Porters Luggage Barrow Used on railway station platforms across Victoria to carry luggage and goods between two locations. Historic - Victorian Railways - Porters Luggage BurrowPorters Luggage Barrow made of Timber - wood and with wrought iron fittings puffing billy, porters luggage barrow, victorian railways

6 NC Brake Van (4 ton capacity) Service History Purchased by the Puffing Billy Preservation Society (Body & underframe only): NC 6 Brake Van (4 ton capacity) - Awaiting restoration *NC 6.VA - 17/12/1919 NWS Built new - /11/1928 - Modified AC Malco BO 5/10/1934 NWS Into Workshops - 9/10/1934 NWS Out of Workshops (5 days) 17/ 3/1955 - Scrapped Historic - Victorian Railways - narrow gauge rolling stock - NC Class Full Guard's Van 6 NCTimber Guards Van wrought iron framepuffing billy, nc van, narrow gauge, victorian railways, 6nc, guards van, narrow gauge rolling stock

V.R NC Class Full Guard's Van body 3 NC ( marked underneath as 22 NQR) 3 NC Brake Van (4 ton capacity) Service History : *NC 3.VA - 17/ 6/1914 NWS Built new - / 5/1928 - Modified AC Malco BO 13/ 8/1932 NWS Into Workshops - 26/10/1932 NWS Out of Workshops (75 days) 11/ 8/1937 NWS Into Workshops - 21/ 9/1937 NWS Out of Workshops (42 days) 19/ 3/1945 NWS Into Workshops - 17/ 8/1945 NWS Out of Workshops (152 days)Historic - Victorian Railways - narrow gauge rolling stock - NC Class Full Guard's Van body 3 NCTimber Guards Van body sitting on wrought iron frame of 22 NQRV.R NC Class Full Guard's Van body 3 NC ( marked underneath as 22 NQR) puffing billy, victorian railways, narrow gauge, nc guards van, narrow gauge rolling stock

BENWERRIN COAL COMPANY SKIP This quarter ton coal truck or skip was used at a small mine situated at Benwerrin near Deans Marsh in Victoria’s Otway Ranges. The mine first opened in 1899 and closed in 1904. With the fuel shortages due to World War 2, the Benwerrin Coal Company reopened the mine in 1941. The coal was loaded into skips and winched out of Box’s Creek valley on a narrow gauge incline to a loading point that was close to the Deans Marsh-Lorne Road. It was then taken by road to the Deans Marsh Railway station. The average gradient of the tramway was 1 in 4 over a length of just under 500 metres (1600 feet). The gauge of the tramway has often been referred to as 375mm (or 15 inches) as shown on the map opposite taken from “Sawdust and Steam”. However, actual measurements of the wheels show the gauge to be 400mm (or 16 inches), which is quite unusual as is the small size of the skip itself. The mine produced up to 30 tonnes of brown coal each week until it closed in 1949 and the incline tramway and its skips were abandoned. Preservation of this coal truck came as a result of interest by the Tramway Museum Society of Victoria (TMSV) in the Barlow or Box type rails that it ran on. These rails had originally come from the Beaumaris Horse Tramway and were obtained by the Benwerrin Coal Company from Hayden Bros’ abandoned timber tramway at nearby Barwon Downs. Members of the TMSV visited the mine in the 1960s only to find that most of the tramway had recently been recovered for scrap. There remained a significant number of relics around the mine adits including most of the skips. One of these remained in good condition and it was recovered for preservation in May 1967. It was restored but never displayed and a second restoration took place by the author over 2012/13 so that it could be placed in the Menzies Creek Museum where it was delivered in February 2013. Little remains of the mine today with trestles and sleepers destroyed in the “Ash Wednesday” Bushfires in 1983. References: Houghton, N (1975), Sawdust and Steam, Light Railway Research Society of Australia. Historic - Industrial Narrow Gauge Railway - Benwerrin Coal Company , Benwerrin , Victoria, AustraliaCoal Skip - made of Iron sheet and wrought iron frame & wheelsB,C.Co Melbournepuffing billy, coal skip, benwerrin coal company, narrow gauge

Sign - Safety Helmet Area, Mines Dept. of VictoriaHistoric - Safety Sign used by Mines Dept. of Victoriametal sign - Sign - Safety Helmet Area Mines Department of Victoria This is a Safety Helmet Area All persons working in or Entering The Quarry or Plant must wear A Safety Helmetpuffing billy, sign - safety helmet area,, mines dept. of victoria

Carriage Sign - Coca-Cola Advertising This board was used to advertise the Coca Cola drink. This particular sign was displayed inside, on the end of the Puffing Billy NBH type carriages. Historic - Puffing Billy Railway - Carriage Sign - Coca-Cola Advertising fitted to NBH carriages.Carriage Sign - Coca-Cola Advertising metal painted sign Enjoy the quality taste Drink Coca-cola ice coldpuffing billy, carriage sign, coca-cola

Carriage Sign - Coca-Cola Advertising This board was used to advertise the Coca Cola drink. This particular sign was displayed inside, on the end of the Puffing Billy NBH type carriages. Historic - Puffing Billy Railway - Carriage Sign - Coca-Cola Advertising fitted to NBH carriages.Carriage Sign - Coca-Cola Advertising metal painted signThe Pause that Refreshes Drink Coca-Cola Sign of Good Tastepuffing billy, carriage sign, coca-cola

Carriage Sign - Coca-Cola Advertising This board was used to advertise the Coca Cola drink. This particular sign was displayed inside, on the end of the Puffing Billy NBH type carriages. Historic - Puffing Billy Railway - Carriage Sign - Coca-Cola Advertising fitted to NBH carriages.Carriage Sign - Coca-Cola Advertising metal painted signThe pause that refreshes Coca-Colapuffing billy, carriage sign, coca-cola

Carriage Sign - Puffing Billy Museum Advertising This board was used to advertise the Menzies Creek Museum after it opened in 1970. This particular sign was displayed inside, on the end of the Puffing Billy NBH type carriages. Historic - Puffing Billy Railway - Carriage Sign - Puffing Billy Museum Advertising fitted to NBH carriages.Carriage Sign - Puffing Billy Museum Advertising metal signVisit the Puffing Billy Steam Museum you can see - Steam Locomotives - Working Exhibits - Early Rolling Stock - Souvenirs available the museum is located at Menzies Creek & opens every Sunday 11am to 5pmpuffing billy, puffing billy museum, carriage sign

Victorian Railways Institute - The VRI was formed in 1909, and started operations at the 3rd Floor, Flinders Street Station, on 31 January, 1910. The Commissioners of the day saw a need for a Social Organisation, where Railway Staff could come together and discuss common issues, and relax in a friendly environment. The VRI was also, for many decades, the Primary Educator of all Rail Staff in their Duties and Tickets, from Train Crews, Station staff and the like, through to the Accounting Office team, everyone was trained at the VRI on how to do their jobs in the VRI. At the height of its power, the VRI would lead a member base of 30,000+ Families, all who would have a dedication to the Rail Industry and VRI. Throughout the State, Centres started, the earliest in 1916 in Ballarat, through to the later ones in Sunshine (1962) and beyond.Historic - Victorian Railways Institute Notice BoardV.R Institute Notice Board made of painted timberV.R Institutepuffing billy, victorian railways institute, notice board

Twin Cylinder Racking EnginesHistoric - Industrial - Twin Cylinder Racking EnginesTwin Cylinder Racking Engines made of metal, iron and steeltwin cylinder racking engines, puffing billy

Clarkat A Clarkat Aircraft Tug that has been converted to run on Rails, This Clarkat 'B' was one of 11 machines shipped on 13 April 1943 to the Lathrop Holding & Re-consignment Depot in Lathrop, California. and was used at Jack's Magazine, Maibyrnong, Victoria and later on at Coal Creek Historical Village, Gippsland, Victoria. Clarkat Tug Model C S/N Cx30F Made by Clark Tructractor Div of Clark Equipment Co Battle Creek Michigan U.S.A Serial No. CK 43 470 Code: Heavy Des.Pat. 116092 Historic - Industrial Narrow gauge railway equipment - Jack's Magazine, Maribyrnong, Victoria, Australia Clarkat Aircraft Tug that has been converted to run on Rails, made of steel Coal Creek Tug Clarkat Serial No. CK 43 470 Code: Heavy Des.Pat. 116092 clarkat, clarkat aircraft tug, puffing billy, jack's magazine

The Refreshment Services Branch was established in 1920, and initially focused on providing station-based refreshment rooms and the dining car service. Its scope expanded to include diverse activities such as stall rental; sales of advertising space on railways infrastructure; laundry services; operation of a hair-dressing salon, a bakery, a butchery and a poultry farm; and the management of the chalet guesthouse at Mt Buffalo. The majority of staff worked in refreshment rooms and dining cars, both of which were a popular feature of the railway service. Previous to 1920 refreshment services had been provided by contractors, but after many complaints the Department decided to provide a standardised service across the system. It grew quickly: five years after it was established the Branch employed approximately 500 staff. Station refreshment facilities ranged from elaborate dining rooms to decorated push-carts. They were staffed predominately by women, who provided everything from a cup of tea to a three course meal. Most refreshment room services were closed in the 1970s. Reference from : Fielding, K. (2012) Victorian Railways - Refreshment Services Branch in Museums Victoria Collections http://collections.museumvictoria.com.au/articles/11470Historic - Replica of a a Victorian Railways Refreshment Services Serving Trolley used on Puffing Billy Railway Replica large wooden serving cart with fitted wooden cabinet featuring sliding glass doors and one glass shelf. Cart has chrome handles, two wooden shelves, a wooden drawer with chrome handle and a small chalkboard adhered to end. Cart has four small black rubber and metal wheels and a metal foot brake.puffing billy, serving trolley, replica, dining cart, refreshment services, victorian railways

Historic - Victorian Railways Station sign used at Whitfield Station Whitfield Station The terminus of the line. Whitfield was the most distant narrow gauge station from Melbourne Opened 1899 Closed 1953 Whitfield was the small terminus for the Whitfield railway line The station had a moderately long passenger platform, small goods yard, goods shed, ticket office and locomotive shed. Platforms 1 Tracks 3 Historic - Victorian Railways Station sign used at Whitfield StationStation Sign - Whitfield large black wooden backing board with white letteringWhitfieldpuffing billy, victorian railways, station sign, whitfield

V.R. Powder & General Goods Van NH1 Gauge 2'6" The NH Powder and Goods van was built in 1910. Its purpose was to carry explosives and general goods, Originally classed as NPH. There were two compartments: a 10ft 8¾ inch (3,270 mm) section for explosives and a 13 ft 7 in (4,140 mm) section for general goods. The sides, ends and doors were covered in sheet metal. With the closing of the mines at Walhalla the need to carry explosives ended and both compartments were used for general goods. The doors were replaced with NU type louvre doors for ventilation. NH1 Covered Truck Service History : NPH NPH 1 was built and issued to traffic June 1910. It was a bogie boxvan set up for general goods and the transportation of explosives. It could carry 6 tons of goods and 4 tons of explosives. No doubt the van was stationed on the Moe - Walhalla line. Walhalla was a gold mining town and the rail line had been built from Moe to provide a faster means of transportation than bullock teams from the sailing boats from Melbourne to Port Albert/Sale via Heyfield. In 1911 the van was converted to all goods transport and recoded to NH. NH The van was fitted with autocouplers in 1928. It was scrapped in 1954. By 1968, the vehicle body had been found and was placed into the Museum at Menzies Creek. Body donated to the Puffing Billy Preservation Society. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 7 tons Capacity 10 tons Built 1910 Number Built 1 In use - Static displayHistoric - Victorian Railways - narrow gauge rolling stock - Powder & General Goods Van Victorian Heritage Register (VHR) Number H2187 Puffing Billy Locomotives and Rolling Stock Collection1 NH - Powder & General Goods Van Made of Timber - wood, wrought iron and metal sheet There were two compartments: a 10ft 8¾ inch (3,270 mm) section for explosives and a 13 ft 7 in (4,140 mm) section for general goods. The sides, ends covered in sheet metal with NU type louvre doors for ventilation. NH1 To carry 10 tonspuffing billy, powder & general goods van nh1, nh1, powder & general goods van, victorian railways, narrow gauge rolling stock

Portable Compound Engine - Marshall & Son's. Builders Number 48317 Built by Marshall Sons & Co., Ltd., Gainsborough, England (Builder’s Number 48317 of approximately 1908/1909), to the order of Robison Brothers, Engineers, South Melbourne. It was used for operating a pump to supply irrigation water at Robinvale in Northern Victoria. Robison Bros & Co. P/L was founded by James McFarlane Robison and his brothers in 1854, initially as plumbers and coppersmiths, the firm expanded into general engineering, boiler-making and brass, iron and steel founders and became one of Melbourne's most important engineering firms. They constructed railway bridges, gold mining equipment, railway locomotives, pumping stations, brewing vessels, abattoir machinery, amongst much else and including the first turnstiles at the Melbourne Cricket Ground. A portable engine is either a steam engine or an internal combustion engine, that remains in one place while operating (providing power to machinery), and can be easily moved from one work site to another. Mounted on wheels or sometimes skids, it is required to be towed between work sites.Historic - Industrial Portable Compound Engine - steam engine - Marshall & Son's. Marshall & Son's Portable Compound Engine - Builders Number 48317 made of steel Marshall & Son's. Builders Number 48317puffing billy, state rivers and water supply commission of victoria, portable compound engine - marshall & son's., portable compound engine, marshall sons & co., ltd., robison bros & co. p/l

0-6-2 Tank Locomotive No.1 "Delta" Gauge 2'0" Identification: 1 Delta Type: 0-6-2T Builder: Perry Engineering, Mile End, South Australia Builder's number: Perry 7967.50.4 of 1950 Building date: 1950 Current status - Static Exhibit Wheel Arrangement 0-6-2T Cylinders (Diameter X Stroke) 10 inches X 18 inches Boiler Pressure 180 psi Driving Wheel (Dia.) 28 ½ inches Weight 16 tons Coal Capacity 27 cubic feet Water Capacity 500 gallons The Perry Engineering Co, Mile End, South Australia built a total of 18 locomotives for the 2’0” gauge tramways used by the sugar industry in Queensland. This 0-6-2T locomotive was built by Perry Engineering Co. Ltd. of Mile End, Adelaide as their Builder's No. 7967.50.4 of 1950. It was used at Qanaba Mill, Bundaberg where it was known as No.1 "Delta". / Qanaba Mill No.1 No. 1 “DELTA” 0-6-2 TANK LOCOMOTIVE Gauge: 2 foot Built by Perry Engineering Company of South Australia in 1950 (Builder’s number 7967.50.4), “DELTA” is a medium sized Australian designed locomotive featuring Walschaert’s valve gear driving piston valves. Weighing 16 tons (16.3 tonnes) it was one of the post-war narrow gauge steam locomotives, which worked in the canefields of Queensland until 1978. “DELTA” worked at various sugar mills in the Bundaberg area and was finally withdrawn from service at Quanba Mill after a life of 28 years. Obtained by the Puffing Billy Preservation Society in 1981. Delivered to Australian Estates Co., Kalamia Mill named DELTA in 1950. Purchased by Fairymead Mill as No 20 DELTA. Purchased by Millaquin Sugar for Qanaba Mill as No. 1 DELTA, 1970 Withdrawn from service, 1978. Obtained by Puffing Billy Preservation Society for display at the Puffing Billy Museum.Historic - Industrial Narrow Gauge Railway - Steam Locomotive used in Queensland in Sugar Mill service. Locomotive No.1 "Delta" - Steam Locomotive - made of steel, and wrought ironDelta0-6-2 tank locomotive no.1 "delta" perry engineering - puffing billy railway perry 7967.50.4 of 1950, puffing billy, qunaba sugar mill, bundaberg, perry engineering, delta, steam locomotive, 0-6-2 tank locomotive no.1

Malcolm Moore No. 1013 Four wheel Diesel Rail Tractor Gauge 2'0" Malcolm Moore rail tractor (Builder’s Number 1013) It was built for the Australian Army in 1943. It was sold to the Inkerman Sugar Mill in Queensland around 1948 for hauling cane and shunting at the works. This rail tractor was originally powered by a Ford side valve V8 petrol engine. It was purchased from the Inkerman Mill of Pioneer Sugar Mills in 1982. Historic - Industrial narrow gauge Railway - Diesel Rail Tractor - used by the Australian Army and Inkerman Sugar Mill in QueenslandDiesel Rail Tractor made of iron and wrought irondiesel rail tractor, puffing billy, inkerman mill, industrial narrow gauge railway, gauge 2’0”, inkerman sugar mill, australian army

Former Puffing Billy Locomotive Boiler 6A - front tube plate missing Historic - Former Puffing Billy Locomotive Boiler 6A - front tube plate missing Former Puffing Billy Locomotive Boiler 6A - front tube plate missing Made of iron , wrought iron , metal;puffing billy, 6a boiler

NKS Type Gangers Trolly - Victorian Railways 2'6" gauge trolly - a KS series Section Car oftern called the Kasey Jones The narrow gauge version of the broad gauge KS series cars. They were classed NKS with two stroke motors. These cars were built by the Spotswood Workshops, with castings coming from the Newport Workshops. KS is lighter car capable of carrying 4 men or sevenhundredweight Historic - Victorian Railways Narrow Gauge - Track Patrol Vehicle used by Puffing Billy Preservation SocietyMotorised small rectangular trolly made of wood and wrought iron Engine Type: 1 Cyl. reversible Fuel: 2 stroke Transmission: Belt driveNKS 8puffing billy, victorian railways, trolley, narrow gauge, 2'6" gauge, kasey, trolly

NKS Type Gangers Trolly - Victorian Railways 2'6" gauge trolley - a KS series Section Car oftern called the Kasey Jones The narrow gauge version of the broad gauge KS series cars. They were classed NKS with two stroke motors. These cars were built by the Spotswood Workshops, with castings coming from the Newport Workshops. KS is lighter car capable of carrying 4 men or sevenhundredweight Trolly 9 was built for the State Electricity Commission of Victoria for use on their metre gauge railway of Yallourn. It was sold to a preservation group at Walhalla and regauged to 2 foot 6 inch. It came to the Puffing Billy Railway in the early 1980s.Historic - Victorian Railways Narrow Gauge - Track Patrol Vehicle used by the State Electricity Commission of Victoria for use on their 900mm gauge railway of Yallourn. And then at Walhalla Railway where it was regauged to 2 foot 6 inchMotorised small rectangular trolly made of wood and wrought iron - currently stored dismantled Engine Type: 1 Cyl. reversible Fuel: 2 stroke Transmission: Belt driveNKS 9puffing billy, puffing billy museum, trolley, narrow gauge, 2'6" gauge, victorian railways, state electricity commission of victoria - yallourn., trolly

Climax geared locomotive No. 1694 in active service on special occasions - stored at Emerald Station A Miraculous Survivor Climax locomotive No.1694 is a miraculous survivor of a rare breed of steam locomotive. For about 100 years from the mid-1850s sawn timber was carted from Victorian sawmills to the nearest railway station by timber tramway. These tramways were generally very rough, steeply graded, sharply curved, and of narrow gauge. Many had wooden rails, and horses provided haulage. The better ones used steam locomotives. In all about fifty steam locomotives are known to have worked on Victorian timber tramways. These locomotives were usually somewhat peculiar - made to cope with arduous, rough conditions, rather than speed. Climax locomotive No.1694 is the only one of these locomotives to survive intact. It was built in 1928 by the Climax Manufacturing Company, Corry, Pennsylvania, USA, for the Forests Commission of Victoria. The distinctive feature of the Climax locomotive is that the cylinders do not directly connect to the driving wheels. Instead they drive a cross shaft near the centre of the locomotive. From there the drive is transmitted to the small driving wheels through rotating shafts, universal joints, and bevel gears. The driving wheels are mounted in two four-wheel bogies so that they can easily follow sharp curves in the track. None of these features are found in normal steam locomotives. The result is a locomotive that is extremely powerful for its size, and that will cope with sharp curves and steep grades with ease. But this is at the cost of speed, Climax locomotive No.1694 is just about flat-out at 13 km/h (8 mph). Climax Locomotive Built in 1928 for the Forests Commission of Victoria and painted all-over black with the name CLIMAX painted on the sides of the cab in white block letters, this locomotive was issued to the Tyers Valley tramway which branched off the Moe to Walhalla line at Collins Siding. This locomotive was withdrawn from service in 1949 following the closure of the tramway and in 1950 it travelled from Tyers Junction to Collins Siding to Erica where it remained stored until 1965. Loaned to the Puffing Billy Preservation Society for its Steam Museum, it was taken to Menzies Creek in 1965 where it remained until 1982 when the Emerald Tourist Railway Board bought it and transferred it to Belgrave for restoration. It was returned to service for special use on the Belgrave to Gembrook line in 1988 painted in its original all-over black livery, except that the word “Climax” on the sides of the cab was now painted in the style of the Climax Manufacturing Co., a style that this locomotive had never carried.Historical - Industrial railway - Forests Commission of Victoria, Timber Logging Climax Locomotive Climax geared Steam locomotive made of steel and wrought iron Climax 1694climax locomotive works, climax, geared steam locomotive, puffing billy, climax locomotive no. 1694, steam locomotive

861 John Benn Locomotive - in active service - Emerald Station Built in 1886 by Société Anonyme Usines Métallurgiques du Hainaut - Locomotives Couillet for the West Melbourne site of the Metropolitan Gas Company, as a four-wheel tank locomotive similar to 986 and named “John Benn”. The West Melbourne gas works sourced its coal from Maitland, New South Wales, and the coal was brought by ship to a wharf adjacent to the West Melbourne gas plant. John Benn and Carbon were used to haul the coal over a 762 mm (2 ft 6 in) gauge railway from the wharf to the gasworks, a distance of about 450 metres (500 yards). It was withdrawn from service in the 1930s and stored until sold privately in 1962. It was rebuilt by its new owners in the style of an American locomotive of the 1880s and was used for some years at Walhalla. It currently has the name “J.C. Rees” and is used in active service for the 861 Footplate Experience. Wheels: 2-4-2ST Builder: Couillet Build Date: 1886 Construction No.: 861 Empty Weight: Unknown Weight on Drivers: Unknown Driver Diameter: Unknown Tractive Effort: Unknown Boiler Pressure: Unknown Cylinders: Unknown Fuel: Coal Gauge: 30 inchesHistoric - Industrial railways - Metropolitan Gas Company Ltd, Melbourne Steam LocomotiveDecauville Steam Locomotive 861 John Reespuffing billy, narrow gauge, industrial narrow gauge railway, metropolitan gas company, decauville 43, steam locomotive, john rees, john benn, 861 locomotive, couillet, 861

G42 Garratt Steam Locomotive Traffic and train loadings on Victoria's narrow gauge railways reached their peak during the 1920s. To assist in handling the longer, heavier trains, the Victorian Railways ordered two larger, more powerful Beyer Garratt locomotives. These were delivered in 1926 and were numbered G41 and G42. They were sent to work on the Colac–Beech Forest–Crowes line and the Moe–Walhalla line respectively. After the line from Moe closed in 1954, G42 was sent to Colac, where it worked with its mate, G41, until closure of that line in mid-1962. G41 had been in poor condition and was scrapped, whereas a brighter future awaited G42. The Victorian Railways offered G42 to the Puffing Billy Preservation Society, for display as a static exhibit in the Menzies Creek Museum. Over time, a plan evolved to restore G42 to operation, a goal that was eventually achieved by the launch of G42 back into traffic in April 2004. G42 now continues to operate as a restored member of the Puffing Billy Railway's locomotive fleet. No. originally constructed: 2 No. in service: 1 (No. 42) Boiler pressure: (lb/sq. in) 180 Boiler heating surface: 1268 sq ft (117.8 m2) Tractive effort: (85%) 26,860 lbs (12.18 t) Driving wheel diameter: 36" (91.44 cm) Max axle load: 9t 5cwt Length Overall: 51' 7" (15.72m) Height Overall: 10' 8" (3.28m) Date of manufacture: 1926 Manufacturer: Beyer Peacock Place of manufacture: Manchester UK Locomotive Type: Garratt Coal capacity: 70 cwt Cylinder diameter: 13" (33.02 cm) Cylinder stroke: 18" (45.72 cm) Wheel arrangement: 2-6-0+0-6-2 Roadworthy weight: 69t Water capacity: 1680 gal (7,637.43 l) Beyer Peacock - Garratt Locomotives Register Works Number - 6268 / 1926 Gauge/Railway/Class - 2'6"/Victorian Government Rlys/G Type - 2-6-0+0-6-2 No. G42 Notes - Australia G42 Built in 1926 and painted all-over black, this Garratt locomotive was issued to the Moe to Walhalla line where it remained—other than for overhauls—until the line closed in 1954. After an overhaul at Newport Workshops, it was issued to the Colac to Crowes line and remained there until that line closed in 1962 when it was returned to Newport Workshops for storage. In 1964 it was sold to the Puffing Billy Preservation Society and removed from the V.R. register 3 months later. It arrived at Belgrave in 1968 and was hauled to Menzies Creek for static display in the museum. 1986 saw the commencement of restoration the Belgrave workshops and has been restored to its 1946 to 1954 condition with raised cab roof, raised marker lamps, steel cow-catchers and all-over black livery. It was returned to service on April 18, 2004. Service History : Jun 1926 - Moe - initial allocation of a new locomotive Jun 1926 - Oct 1954 Moe Oct 1954 - Jan 1955 Workshops Jun 1955 - May 1962 Colac Jul 1962 - Dec 1965 Workshops - Stored Jan 1968 - Feb 1968 Belgrave - Stored Feb 1968 - 1982 - Menzies Creek Steam Museum 1982 - 2004 - Under restoration Apr 2004 - Belgrave - In active service at Puffing Billy Railway BelgraveHistoric - Victorian Railways - Narrow Gauge - Garratt Steam Locomotive - G42 Victorian Heritage Register (VHR) Number H2187 G42 Garratt Steam Locomotive made of steel, iron and wrought iron with brass fittings - the Locomotive is in Active Service - Belgrave Station G42puffing billy, narrow gauge, garratt, g42, steam locomotive, beyer peacock, victorian railways

Belgrave railway station is the terminus of the electrified line from Melbourne in Victoria, Australia, serving the eastern Melbourne suburb of Belgrave. Opened as Monbulk on 18 December 1900, it was renamed Belgrave on 21 November 1904. It was upgraded to a Premium station on 2 July 1996. The station was originally on the Upper Ferntree Gully – Gembrook narrow gauge line. It, along with the rest of the line, officially closed on 30 April 1954. However it saw further use between 1955 and early 1958, when trains were operated by the Puffing Billy Preservation Society in co-operation with the Victorian Railways. The station area re-opened on 19 February 1962 when the line as far as Belgrave was converted to broad gauge and used electric traction as part of the suburban network.[1] It has one island platform with two faces. It is serviced by Metro Trains' Belgrave line services The Puffing Billy Railway Belgrave station is located 100 metres north of the station and is accessible via a short footpath. It was required to be located further down the line than the original narrow-gauge station (which was approximately where the current suburban station car park is located). ref: https://en.wikipedia.org/wiki/Belgrave_railway_station photos at http://www.vicrailstations.com/Gembrook/Belgrave/Belgrave.htmlHistoric - Victorian Railways Station sign used at Belgrave StationStation Sign - Belgrave Metal sign - white enamel back ground with black letters Belgravepuffing billy, victorian railways, belgrave station

Station Sign - Yea Yea Station Opened 16 November 1883 Closed 8 November 1978 Yea is a former railway station in Yea, Victoria, Australia. The tracks have been removed and the reserve has been turned into The Yea Railway Park consisting of the historic railway station and eleven acres of parkland. It has a picnic shelter, barbecue, toilets, playground, skatepark, walking track, community reserve and includes Rotary Park. The station building houses Blackthorn Textiles (a privately run craft shop). Also on the site are the former goods sheds which are available for hire for varied functions. The Yea Country Market is held in the park on the first Saturday of each month and local artists hold an exhibition and sale in the goods sheds each Easter. The site is listed on the Victorian Heritage Register ref: https://en.wikipedia.org/wiki/Yea_railway_station photo at http://vhd.heritagecouncil.vic.gov.au/vhd-images/places/000/078/092.jpg Historic - Victorian Railways Station sign used at Yea StationStation Sign - Yea Metal rectangle Station Name Sign with white enamel back ground and black lettersYeapuffing billy, station sign, yea station

Station Sign - Tecoma Tecoma railway station is located on the Belgrave line in Victoria, Australia. It serves the eastern Melbourne suburb of Tecoma opening on 1st December 1924. The station was originally on the Upper Ferntree Gully - Gembrook narrow gauge line. It along with the rest of the line closed on 30 April 1954, reopening on 19 February 1962 when the line as far as Belgrave was converted to broad gauge. ref: https://en.wikipedia.org/wiki/Tecoma_railway_stationHistoric - Victorian Railways Station sign used at Tecoma StationStation Sign - Tecoma wooden rectangle Station name sign pained yellow background with black letters Tecomapuffing billy, station sign, tecoma station, narrow gauge, puffing billy museum

Upwey Station Sign; Upwey Railway Station is located on the Belgrave line in Victoria, Australia. This railway serves the Eastern region of Melbourne. Upwey Railway Station opened on the 3rd of June 1901. Upwey Railway Station has a crossing loop in the middle of a six kilometre section of single railway track between Ferntree Gully Railway Station and Belgrave Railway Station. The station was originally on the Upper Ferntree Gully to Gembrook narrow gauge line. The Upper Ferntree Gully to Gembrook Narrow Gauge railway line officially closed on the 30th of April 1954. It saw further use between 1955 and early 1958, when trains were operated by the Puffing Billy Preservation Society in co-operation with the Victorian Railways. The Upper Ferntree Gully to Belgrave section was converted to Broad Guage and re-opened on the 19th of February 1962. This station sign shown here was one of a number used on the Upwey Railway Station while it was Narrow Gauge. Historic - Victorian Railways Station sign used at Upwey StationUpwey wooden rectangle Station name sign pained yellow background with black font.Upweypuffing billy, station sign, upwey station, victorian railways

Station Sign - Fielder Fielder Station is situated on the Puffing Billy Railway in Australia. It opened as a Stopping Place on Monday 10 September 1928, as part of the Gembrook railway line. It was originally an unnamed platform, with time tables noting a station at 38 miles (61 km). In 1929, local Harry Watson constructed a Mallee shed and unofficially named it Ancaster after his home town in Lincolnshire, England, but this was quickly changed by some children to Laura, who was a young local girl. The Victorian Railways officially named it Fielder from Tuesday 5 February 1929, after a nearby resident. It was planned to name the station after the two local residents Cullen and Fielder and combinations of the two names were suggested, however Fielder was the name finally chosen. It remained nothing more than a Mallee shed with small office and a name board for the rest of its operating life. It was closed with the line on 30 April 1954 and the Mallee shed was sold to US Buslines for unknown use. After closure, the site fell into disrepair, and by the 1990s, little trace of Fielder remained. However, by that time, efforts were being made to extend the railway from Lakeside through to Gembrook, which would complete the entire length of the original line. In 1996, a group of volunteers led by Richard Schurmann in collaboration with the descendants of the Fielder family rebuilt the platform and waiting shed, which was officially re-opened on Saturday 19 April 1997 in preparation for the extension of the line which re-opened in 1998. On 18 November 2012 a plaque was unveiled on the station shed in tribute to the Fielder Family Trains do not normally stop at Fielder ref: https://en.wikipedia.org/wiki/Fielder_railway_station photos at http://www.vicrailstations.com/Gembrook/Fielder/Fielder.htmlHistoric - Station sign used at Fielder StationStation Sign - Fielder wooden rectangle Station name sign pained black background with white lettersFielderpuffing billy, station sign, fielder station

Station Sign - Emerald Emerald Station is situated on the Puffing Billy Railway in Victoria, Australia. It was opened with the Railway on 18 December 1900 and comprised a platform track and a loop siding. A passing loop was added between the two a few years later. There was also a spur siding off the Down end of No. 3 Road. Two standard 12 ft by 20 ft timber portable station buildings with a Van Goods Shed between (all adjoining) were provided on the platform and a Goods Shed on the No. 3 Road loop siding. Other buildings included Tea Rooms, lamp room and toilets along with a cattle race and loading bank. The station building was later reduced in length by one of the portables which housed the General and Ladies' waiting rooms. Emerald today remains very similar to the early days, but has had other Roads added into a Carriage Workshops, a turntable and storage sidings. Also, a Signal and Telegraph Branch depot in the form of a large Goods Shed and a multi-purpose yard building in the form of a Locomotive Depot administration building have been added. During 2009, the station building underwent stage one of an internal restoration to its former glory. ref: https://en.wikipedia.org/wiki/Emerald_railway_station,_Victoria photos at http://www.vicrailstations.com/Gembrook/Emerald/Emerald.html Historic - Victorian Railways Station sign used at Emerald Station Station Sign - Emerald Metal rectangle Station Name Sign with white enamel back ground and black lettersEmeraldstation sign, puffing billy, emerald station