Hampton & Sons 1942

A sailing block is single or multiple pulleys with one or more sheaves that are enclosed in an assembly between cheeks or chocks. In use, a block is fixed to the end of a line, to a spar, or a surface. A rope line is reeved through the sheaves, and maybe through one or more matching blocks at the far end, to make up what's known as a tackle. The purchase of a tackle refers to its mechanical advantage. In general, the more sheaves in the blocks that make up a tackle, the higher its mechanical advantage. The matter is slightly complicated by the fact that every tackle has a working end where the final run of rope leaves the last sheave. More mechanical advantage can be obtained if this end is attached to the moving load rather than the fixed end of the tackle. Various types of blocks are used in sailing. Some blocks are used to increase mechanical advantage and others are used simply to change the direction of a line. A ratchet block turns freely when a line is pulled in one direction but does not turn the other direction, although the line may slip past the sheave. This kind of block makes a loaded line easier to hold by hand, and is sometimes used on smaller boats for lines like main and jib sheets that are frequently adjusted. A single, large, sail-powered warship in the mid-19th century required more than 1,400 blocks of various kinds and sizes. An item from an old sailing vessel from the late 19th to early 20th century, unfortunately, the item cannot be identified as to what vessel it belonged to. It does however give an insight into a piece of sailing equipment that's design is still in use today on pleasure sailing craft. Wooden closed spelter double rope block with two pully's between sheaves, block has metal frame around outside of the sheaves and 4 metal pins, 2 each side of the frame at top and 2 at bottom, joining the sheaves together. The shaft between the sheaves is also wooden. Remnants of orange and black paint on outside of block. Shafts are chipped, wood has borer holes. (NOTE: Block was rediscovered after relocating objects to new storage area)Noneflagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, sailing ship, pulley, block, sheave, ship equipment, rope block, sail rigging

This Trotman’s pattern stock anchor is the southernmost anchor on display at Flagstaff Hill’s Anchor Graveyard. This large Trotman design anchor was patented in 1852 by John Trotman and was widely used on merchant ships. On April 15th 2001 around midday this anchor was raised from the seabed of Lady Bay, Warrnambool, by the crew from Birdon Dredging, who had been hired to dredge the Harbour. The spokesperson Steve Walker, who worked for the firm, said that the anchor and long chain were found after the chain became tangled in the cutter blade of the dredging equipment. The anchor was lifted from the water and onto the Breakwater then a front-end loader placed it onto a truck that then delivered it to Flagstaff Hill Maritime Museum & Village. Howard Nichol, Museum Manager at the time, had estimated the anchor to be up to 130 years old. The previous Museum Manager, Peter Ronald, who was also a diver, had identified the anchor as a Trotman’s type and similar to those used on some of the major wrecks in the region. According to Nicholl, Museum staff believed it was possible that the anchor is one of two used as a mooring line that had been used to catch driving vessels and prevent ships from washing aground on the sand bar. The mooring line was shown as a dotted line on the 1890 chart of Lady Bay, approved by Lieutenant Stanley of the British Admiralty. by Lieutenant Stanley [British Admiralty]. The location of the anchor corresponds to a point on that map and the length of the chain supports that theory. “The map is quite a detailed survey of the Bay and it shows two anchors with buoys on the ends with probably about 100 yards of chain stretched between them. The ships would drop anchor and was the chain as a snag because this was a treacherous bay before the Breakwater was built and this was a way to eliminate that problem, "said Nichol. The mooring chain was put in place to catch drifting vessels during wild stormy weather. It was identified. ABOUT TROTMAN’S ANCHORS- The British Admiralty wanted an anchor design that had more holding power. The Committee of 1852 on Anchors was appointed to assess and report on the qualities of various anchors including Trotman’s anchors. Trotman’s pattern anchor received the highest score. The anchor is similar to the Admiral’s design but features arms that pivot when the anchor settles and the upper fluke moves to rest against the shank. The anchor then sits lower, which in turn greatly reduces the chances of the anchor’s chain, cable or rope getting tangled. The top of the shank has a fitting that allows a quick release of the anchor’s chain if this becomes necessary. This Trotman’s anchor is significant as a part of the maritime history of the Port of Warrnambool regardless of whether it belonged to one of the 29 ships that were stranded or wrecked in Lady Bay. The anchor is connected to the many attempts to maintain Warrnambool as a safe and manageable port, including the various plans for the construction of the Breakwater.Anchor: an iron Trotman’s pattern style with a rectangular-section shank that is wider in the middle and has a base that extends on two opposite sides in a ‘fork prong’ manner. A crescent-shaped, double-ended arm is fitted into the base of the shank with a bolt, enabling it to pivot. Each arm has a fluke in the shape of an upward palm with an attached metal plate that forms a horn at the back of the palm. A long, round-section pipe is fitted to the top of the shank at 90 degrees to the arms; one side has an elbow bend parallel to the arms, and both ends have an attached metal sphere. The pivoting ring at the top of the shank can be lifted for a quick release of the chain.flagstaff hill, warrnambool, maritime village, maritime museum, shipwreck coast, great ocean road, anchor, mooring, trotman, lady bay, breakwater, admiralty, ship equipment, stock anchor, john trotman, 1852 patent, 2001, birdon dredging, steve walker, howard nichol, peter ronald, british admiralty, lieutenant stanley, committee of 1852 on anchors

Pouch, small, brown leather with strap fastening. Short cord & metal clip attached to strap at back, stitched with rivet reinforcements.trades-leatherworking, military equipment - containers, passchendaele barracks trust

Portable morse code metal box with canvas shoulder strap. Case Mark II PMG Melbourne 1942

Metal, flat round plate with flange for attachment to headligh, with with metal hood attached (welded/soldered?). Light slot attached from backnone

Used at the Ballarat School of Mines Chemistry Labratory, which was closed and dismantled with TAFE Cuts.Wooden test tube holder with teh capacity to hold six test tubesscientific instrument, test tube holder, laboratory

A plastic device to enable a sighted person to communicate with a person who is Deaf-Blind in either standard Braille or Moon. The centre radius of the disc has the ordinary alphabet printed in black. Moving outwards from the centre, are the corresponding letters embossed in Braille, then on the outer edge are the corresponding letters in Moon. The user moved the indicator arm around the disc until the desired letter and corresponding symbol was positioned under the cut-out in the centre of the arm. The deaf-blind person could then touch the disc to determine the letters being communicated. Numbers and punctuation are not included.White plastic disc with black indicator armbraille equipment, assistive devices

A steam boiler like this late 18th century boiler, is often called a colonial boiler. Steam boilers were used in factories throughout Australia, mounted over similar designs of brick furnaces. This heat from the fire travels through the tubes in this fire tube boiler and the water heats as it circulates around them. Another kind of boiler is a water tube boiler, in which the water is inside the tubes and the heat of the combustion surrounds the tubes. The boiler in our collection burned wood as fuel but others of this design could also burn coal, coke, gas and liquid fuels. The boiler was made by T & F Johnson, boilermakers. In 1922 their factory was located at Coventry Street, South Melbourne. They were still advertising their 'Colonial, multi, vertical boilers, all sizes' at the same address in 1934. The connected pressure gauge, made in London by Dewrance, measures 0 to 400 pounds per square inch. John Dewrance is renowned as a pioneer of the steam locomotive in the early 19th century. He founded John Dewrance & Co. in South London in 1844. His son Sir John Dewrance took over in 1879. In 1939 the company became a subsidiary of Babcock & Wilcox, and was eventually owned by Emerson. How the boiler works: - A boiler is about two-thirds filled with water and heat is applied, in this case in the form of burning wood. The heat is transferred through the metal of the boiler to the water. When the water boils the steam rises to the top, and as it escapes from the boiler the steam pressure builds up in the steam space to later be released to do work; drive machinery such as ship and train engines, turbines, presses, wheels, and driving belts to operate looms and saws. The heat associated with the boiler can be used for preserving food, sterilising, factory manufacturing processes, and steaming wood for shipbuilding. Every boiler has several components fitted for safe operation: - - Safety valves - Gauge glass - Pressure gauge - Main steam stop valve - Water check valve - Blowdown valve - Manhole doorThe boiler is a significant item that gives us a snapshot of early Melbourne's industrial history. It is an example of the technological advancement during the Industrial Revolution where steam-driven machinery and motors could perform tasks more efficiently than manual labour. The makers were one of many boilermaker businesses in Melbourne during the early late-19th andearly 20th centuries. The maritime trade and skills of boilermaking are still learned and applied today. The Dewrance steam pressure gauge connected to the boiler was made by the London firms foundered by John Dewrance. He was renowned for developing the steam locomotive in the early 19th century.Boiler; a horizontal cylindrical underfired steam boiler. It is a multi-tubular design and is timber plank-clad, with brass fittings and pressure gauges. The boiler has an iron door at one end with a metal chimney above it. It is installed over a brick-enclosed solid fuel furnace. Two large, wood-mounted pressure gauges are connected to the boiler and have inscriptions. An inscription is on a red, cast iron plaque above the boiler door. The boiler's maker is T & F Johnson, South Melbourne. One of the pressure gauges was made by Dewrance, London..Maker's plate: "T & F JOHNSON / BOILERMAKERS / SOUTH MELBOURNE" Pressure gauge: "POUNDS PRESSURE / PER [square] INCH / DEWRANCE LONDON"flagstaff hill, warrnambool, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, boiler, multi tube boiler, steam boiler, steam technology, underfired boiler, horizontal boiler, timber clad boiler, steam power, industrialisation, boilermakers, south melbourne, dewrance, john dewrance, pressure gauge, dewrance pressure gauge, t & f johnson, london, steam engine, steam locomotive, pounds per square inch, 19th century, steam machine, johnson tyne foundry, colonial boiler, fire tube boiler

Leather pouch for inclusion on belt issued to soldiersBrown leather pouch with two belt keepers on the back. Has large yellowing stitching.On back has C.H.F. ^ engraved into the leatherleather pouch, pouch, leather, map case, belt pouch

The Sydney Homeopathic Dispensary was established in July 1858. At a time when medicine was become more scientific and evidence based, homeopathy relied on the Galenic tradition to treat patients.Wooden box with two drawers secured by a brass pin inside top lid, containing a variety of homeopathic substances. Some of the cork tops are missing, others are broken but sealed. Some of the cork tops have the abbreviated name of the contents on them.Printed in gold leaf on the inside of the lid: JOHN BELL. / HOMEOPATHIC CHEMIST. / GEORGE STREET / SYDNEY.homeopathy, galen, homeopathic, galenic

Popular mass market manual camera. Made by the Eastman Kodak Co. of Rochester N. Y.Black box camera, hinged rear panel; with exposed 116 film and "Picture taking with the Nos. 2 and 2A Brownie cameras" bookletNo. 2A Brownie/Model C/Use Film No. 116/Eastman Kodak Co./Rochester N. Y.cameras, brownie camera, photography

Small hand-operated black painted metal sewing machine with gold decoration. Placed on a wooden base. Has rectangular wooden lid. Made by Frister & Rossmannsee photossewing, sewing machine, hand-operated, frister & rossmann

Khaki webbing belt with brass buckles, clasps and brass keepers for length adjustment. At the back of the belt there are two additional brass webbing fittings for attaching basic webbing straps."HALL"passchendaele barracks trust, webbing belt, equipment

These forceps are a type of uterine forceps used for gynaecological procedures. This is one of a collection of items associated with Dr Felix Henry Meyer (1858-1937). Meyer was a very prominent early obstetrician and doctor, playing a part in the establishment of the role of the chair of obstetrics at the University of Melbourne in 1929. He was also a foundation member of the Royal Australian College of Surgeons.Set of metal scissor style forceps. Consists of two blades, joined with a pin, with a small ratchet for clamping below the finger grips/handles. The end of the forceps curves to one side, and each blade of the forceps ends with a hook. When the forceps are closed, the hooks on either blade join together to make a loop.surgery

Imported and sold by Holden and Frost during the late 19th century and early 20th century for use on saddlery Retailed by Holden and Frost for military agriculture and civilian use c1910Nickel plated Bridle roller buckleequine, military, agriculture, civilian ca1910

Used on horse tackle in the 19th and 20th centuries and imported by Holden and FrostSold by Holden and Frost for military agricultural and civilian use C1900Steel spring tandem hook used on horse tacklehorse equine military, iculture, spring tandem hook

A telegraph or Morse key, sends a series of electrical signals down a telegraph line or via radio frequencies; the signals are interpreted as Morse code, a binary form of language constructed of 'dots and dashes', combinations of which correspond to letters of the alphabet. The motion of the key acts to complete an electrical circuit between the sender and receiver, producing a short pulse 'dot' or longer 'dash,' the space between the code indicates a broken current or wave.Device used to transmit telegraphic messages in Morse code through the manipulation of electric signals. The metal 'key' sits in a central bracket on which it moves up and down aided by a spring, controlled by an operator pushing the black Bakelite knob on the protruding end of the device. The motion presses the key onto a circular metal disc, completing the circuit and sending an electrical pulse to the receiver. The apparatus is secured to a wooden base with wires attached to the terminals; a cut out section of the base suggests wires may have entered through this area, attaching to a battery.Printed ink on base: "PMG"telegraph, telegraphist, morse code, mechanisation

This item is from the private collection of George Shirling of Red Onion, Falls Creek. It recognises his participation at the Winter Olympic Games in Albertville in 1992 where he was the team psychologist. 23 Australian athletes competed, participating in alpine skiing, biathlon, bobsleigh, cross-country skiing, figure skating, freestyle skiing, luge, short track speed skating, and speed skating. Steven Lee and Adrian Costa from Falls Creek were included in this team. The Men's Downhill competition of the Albertville 1992 Olympics in which Steve Lee competed was held at Val d'Isère on Sunday, 9 February 1992. George Shirling arrived in Falls Creek in 1962. He engaged Phil Nowell to build the original Koki Alpine Lodge which opened in 1965 with 14 beds. George operated the lodge with Michael “Baldy” Blackwell as manager. He credited the success of Koki to “Baldy” Blackwell. “Baldy” with Phil Nowell started the Trackers Mountain Lodge in partnership during the 1980s. In 1971 George sold Koki Lodge to Sigi Doerr. He also graduated in sport psychology in 1981 and George later owned the Red Onion Chalet. In 2024 the renamed Koki Alpine resort remains a highly popular destination in Falls Creek. George Shirling passed away on 27th February 2023. He had remained actively involved in Falls Creek and was generous with his time and knowledge, always an amazing supporter of The Falls Creek Museum and Falls Creek Village.This item is significant because it was worn by Steve Lee at the Albertville Winter Olympics 1992.A racing bib worn by Steve Lee at Albertville. It is white with red trim. It bears the Albertville Olympic logo and the number 46 in black. A typed sign is included in the display. Albertville Olympic Logo 46 Val d'Isère On Sign ITEM No 110 Racing Bib No. 46 - downhill - Steven Lee Albertville Winter Olympics, 1992 Donation of Steven Lee george shirling, albertville 1992, steve lee, adrian costa

Item re Frederick Gardner DAVEY DFC No 410533 RAAF. Refer Reg No 3536P for his service details.Cloth bag containing x 2 First Field Dressings each in a waterproof cover. Instructions for use printed on the front.dressings, medical, wounds

Manufactured and sold by Holden and Frost during 19th century Manufactured and sold by Holden and Frost for equine, militarty, agricultural and civilian use C1900Nickel D Girth used as an equestrian accessoryequine, military, agriculture, civilian c1900, girth strap ring

Unable to locate by either name or number.Faded army green long narrow heavy cotton duffle bag, used for carrying personal items. It has a top draw cord which threads through a series of brass eyelets. The draw cord when closed can be used as a carrying device."216 N. MC GR--OR?" = 3 red lines, "VX18238 61077". On base, "VX18238 61077". passchendaele barracks trust, duffle bag, equipment

Wooden folding table with canvas struts underneath and a leather securing strapSVYtable

This apparatus was devised by Hamilton Irving an English general surgeon in 1907. Supra pubic prostatectomy surgery was being performed more frequently due to improvements in procedures. There were issues post-operatively as dressings were saturated with urine and causing excoriation. The receiver was said to be easy to apply, comfortable to wear and effective in keeping the patient dry and able to move freely in bed. Supra pubic urinary drainage cover/receiver, metal with two drainage outlets to enable urine to drain via an abdominal drain tube following a supra pubic cystoscopy and prostatectomy, held in place by a leather belt, two rubber tubes were then attached other ends placed in a urinalFront of appliance has 'RAMSAY' inscribed as well as 'Wd 3' [Ward 3].post operative prostatectomy 1930s, medical equipment

Kodak Tele-Ektalite 600 Camera. Instruction Book and film 200 KodakKodak 600photography, photographs / slides / film

In the early 1920s Australia was gifted six J class submarines from the Royal Navy. These were the latest and largest submarines built by the RN for service in World War I. They were competent but were in service with the Royal Navy for only a short time before the end of the war. Once in Australia they were placed into service but there was little appetite for submarines or in fact any other military endeavour in the early ‘twenties’. The world was exhausted from a long and dirty war followed by a devastating Influenza Epidemic. The J class boats were soon retired and sunk as breakwaters or scuttled in the ship graveyard area off the mouth of Port Phillip Bay.Popular diving sites in Ships Graveyard outside the rip between Point Lonsdale and Barwon HeadsCircular brass plaque inscribed with J5 North Sea 1917 1918 made from a piece of navigational equipment used on the submarine J5 mounted on woodSubmarine J5 North Sea 1917 - 1918j class submarines, j5, ships graveyard, port phillip

Francis Robert LEONARD SX8804. Enlisted 13/07/1940. Discharged 17/01/1946. Rank Private, 2/166 Aust Workshops.Khaki webbing belt with evidence of green colouring. The belt has brass clasp fittings and brass sliding keepers. On the inside of the belt, the sewn in adjustment points are very worn and have been well used. There are two close additional brass webbing attachment points towards the centre of the belt."SX8804"passchendaele barracks trust, leonard, webbing belt, equipment, ww2