The Ballarat School of Mines often conducted assaying for a fee in their Model Mine. Ballarat School of Mines Assay card. Mr Sargent (most probably Robert M. Serjeant) presented 18 bags of sandstone for assayingballarat school of mines, assay, assaying, sandstone, serjeant, r.m. serjeant, robert m. serjeant., mining

Hardcover book with dustjacket, 90 black and white photos. One colour photo of print. Maps on end pages.non-fictionHistory of Alfred Hospital Melbournealfred hospital, ahnl, nursing history, melbourne, prahan

R.M. Serjeant was listed as a mining manager and Joseph Flude as a metallurgist. In 1875 they were both living in Ballarat. The patent number is A.D.1875, 4th March. No 2031. According to the patent the hearth of the furnace is in the form of a cone revolving horizontally. The feed is supplied to the apex of the cone by an archimedian screw. The crown of the furnace comprises a double covering or roof with an intermediate chamber for receiving heated air. The inner covering is pierced to admit of the heated air being brought into contact with the pyrites on the face of the revolving hearth. The discharge of the roasted substance is affected by means of a scraper at the base of the cone. It was claimed that this was a new mode of introducing heated air, and the exclusion of flame during the operation of roasting pyrites. The self-acting charge and discharge of the furnace and the peculiar construction of the hot air chambers, and the use of perforated bricks through which the supply of air is affected were also new. (http://patentsvictoria.net/002031.html) From the Goulburn Herald, 14 September 1878 "A feature connected with the school of mines is the yet unfinished pyrites works. The extraction of the gold from pyrites and the utilization for commercial purposes of other substances connected with pyrites are peculiarly important to Ballarat, because were a simple and inexpensive method devised there are millions and millions of tons of quartz that would then be made remunerative. With this thought in their minds two scientific gentlemen invented the school of mines self-acting rotatory furnace. This, for lack of funds, has not been completed as yet, but the amount in hand for the purpose is daily increasing, and it will eventually be an accomplished fact. It is in contemplation also to erect machinery shops in connection with the school, and it is purposed to con struct a steam-engine to do at once the work of the pyrites treatment and the ma chine room. A model shaft and mine too are being prepared for on the reserve, so that practical mining of the most thorough character may be taught on the ground.'Large indenture on red bordered vellum. The indenture was regarding a patent for the benefit of the Ballarat School of Mines. Letters Patent for an Invention for Roasting Pyrites to be called 'the Ballarat School of Mines self-Acting Pyrites Furnace" to Robery Malachy Serjeant and Joseph Flude. The large document is on a vellum type paper complete with stamps and seal. The document is signed by Acting-Governor William Stawell. Inscriptions and Markings Written on verso: "Date of Patent 4th March 1875 No 2031 Letters Patent for An invention for roasting pyrities to be called "The Ballarat School of Mines Self-acting Pyrities Furnace" to Robert Malachy Serjeant and Joseph Flude Melbourne, Victoriaballarat school of mines, serjeant, r.m. serjeant, robert m. serjeant, flude, joseph flude, patent, barry, redmond barry, rogers, judge rogers, bland, rivett henry bland, john airy, warrington rogers, establishment, indenture, legal, cuthbert, ballarat school of mines trustees, william stawell, john warrington rogers

HMS Nelson was a 126-gun ship of the line of the Royal Navy. Launched on 4 July 1814 at Woolwich Dockyard she was later converted into a screw ship in 1860, and was cut down to a two-decker and fitted with an engine of 2,102 indicated horsepower. In 1865, HMVS Nelson was given to the colony of Victoria as a training ship. She was outfitted and rigged for £42,000 and sailed for Australia in October 1867. Travelling via the Cape of Good Hope, she arrived in February 1868. She was the first ship to dock in the newly constructed Alfred Graving Dock in Williamstown, Victoria.Possibly the first training ship of the Victorian Navy which had a base in Swan Island in Queenscliffe.A black and white photograph of the sailing ship HMS later HMVS Nelson docked at the Alfred Graving Dock, Williamstown, 1872"Nelson" in Alfred Graving Dock Williamstown, Victoria 1872hms nelson, hmvs nelson, alfred graving dock, williamstown

Certificate awarded to Sidney MacDowell upon graduation from the Alfred HospitalOf significance to the AHNL As an example of a nursing graduation certificateBlack gilt embossed folder containing illustration of the Alfred Hospital and a signed certificateOutside cover has traces of gilt embossing.on the front the words Nurse's Certificate and Alfred hospital'. The certiate reads: Alfred Hospital Training School for Nurses Melbourne "October,2nd" 19"45" This is to certify that "Sydney Mabel Hay Macdowell" has attended the prescribed course of Lectures of his Hospital and completed Three years of training. She has passed her Examinations "--------" and is qualified to be registered as a trained general nurse. signed by hospital president (A.Stewart) manager&secy (?) matro (M.Rowe) examiners (? & C.Dyte) and chairman Hon , med. staff (Leonard Ball) atthe side sinature of nurse " Sidney M H Macdowellnurse, certificate, alfred hospital, ahnl

Private George Alfred Williams Service number 70 Final Rank Private Unit 13 Fld.Amb. Conflict/Operation First World War, 1914-1918 Rolls First World War Nominal Roll: Unit 13 Fld.Amb. Conflict First World War, 1914-1918 Rank Private Timeline Date of enlistment 22 September 1914 Date of fate 17 September 1918 Father W.A. Williams of Belle Vue, Eltham Promoted to Corporal 15 March 1916 and transferred to 6th Field Ambulance Transferred to 13th Field Ambulance 9.2.17 Made temporary Sergeant from 27 April to 26 May 1918 whilst his unit awaited a replacement Sergeant at which point he reverted to Corporal. Died of shrapnel wounds to his left side and face received in action with the 4th Australian Field Ambulance in France, 17 Sep. 1918 His mother, Mary Ann Williams (nee Kidd) gave written permission for him to enlist In his Will he left all his effects to his mother.. Williams George Alfred : SERN 70 : POB Heidleberg VIC : POE Broadmeadows VIC : NOK F Williams W A https://recordsearch.naa.gov.au/SearchNRetrieve/Interface/DetailsReports/ItemDetail.aspx?Barcode=1807628&isAv=Nmarg ball collection, 1914, george alfred williams, tesla studios photographer 244 chapel st prahran

Private George Alfred Williams Service number 70 Final Rank Private Unit 13 Fld.Amb. Conflict/Operation First World War, 1914-1918 Rolls First World War Nominal Roll: Unit 13 Fld.Amb. Conflict First World War, 1914-1918 Rank Private Timeline Date of enlistment 22 September 1914 Date of fate 17 September 1918 Father W.A. Williams of Belle Vue, Eltham Promoted to Corporal 15 March 1916 and transferred to 6th Field Ambulance Transferred to 13th Field Ambulance 9.2.17 Made temporary Sergeant from 27 April to 26 May 1918 whilst his unit awaited a replacement Sergeant at which point he reverted to Corporal. Died of shrapnel wounds to his left side and face received in action with the 4th Australian Field Ambulance in France, 17 Sep. 1918 His mother, Mary Ann Williams (nee Kidd) gave written permission for him to enlist In his Will he left all his effects to his mother.. Williams George Alfred : SERN 70 : POB Heidleberg VIC : POE Broadmeadows VIC : NOK F Williams W A https://recordsearch.naa.gov.au/SearchNRetrieve/Interface/DetailsReports/ItemDetail.aspx?Barcode=1807628&isAv=Nmarg ball collection, george alfred williams, 1918, aif, first world war, honour roll

Black and white image of George Street Sydney.sydney, george street

Professor Ernest Edgar Kurth of the University of Tasmania, invented a faster, simpler and cleaner way to produce charcoal on a continuous basis during the second world war. The charcoal was used to produce a combustible gas in motor cars, as a substitute for petrol, which was heavily rationed. The first batch of charcoal was produced in February 1942 and continued until the end of the war. Wood from stringybark trees was cut into lengths and fed into a kiln which converted it into charcoal. The Kiln is located on Beenak Road, 7km north of Gembrook. It has great historical significance, particularly as an alternative supplier of fuel during the second world war. It is a State Registered facility, managed by the Friends of Kirth Kiln and the park is managed by Parks Victoria Green soft covered book of 150 pages, with a photo of 2 men and a boy out in the bush with 3 fires burning.Contains a Prelude about Ernest Edgar Kurth written by Alfred Klink (2013) and a Foreward by John Sullivan (Heritage Officer of Parks Victoria). There is an Acknowledgement page, with recognition given to the grant provided by the Department of Sustainability, Environment, Water, Population and Communities. e.e. kurth, kirth kiln, charcoal kiln, parks victoria

Illustrated book with light blue cover. Abbreviated title and authors name printed in silver on front cover and spine.non-fictionA history of nursing at Royal Prince Alfred Hospital, Sydney from 1882 to 1932.royal prince alfred hospital -sydney-history, nursing-nsw-history, nurses

The Process of Making Pottery Decorating, Firing, Glazing, Making, Technical There is a rhythm and flow to clay. It can’t be done all at once! Even the making process! It can take weeks to get everything done, especially if you can only work on your pottery once a week! Even though we have three hour classes, it’s often just not enough time! Here is an overview of some of the processes so you have a bit more grasp on some of the technical stuff! Step One – Design There are SO many ideas out there for making stuff in clay! From delicate porcelain jewellery, through to heavy sculptural work and everything in between. Deciding your direction is sometimes not that easy – when you first start, try everything, you will naturally gravitate to the style that you enjoy! The options and variations are endless and can get a wee bit overwhelming too! Check in with me before you start to ensure your ideas will work, what order you might do things, how you could achieve the look you are seeking and any other technical data required! Step Two – Making Clay is thixotropic. This means that as you work with it, the clay first gets sloppier and wetter, before is begins to dry in the atmosphere. For most things, you simply can’t do all parts of the project at once. An example of work order might look like: Get last weeks work out from the shelves Prepare clay for today’s work – roll your clay, prepare balls for throwing, make the first stage of a pinch pot) Clean up last week’s work and put it on the shelf for bisque firing Check that you have any glazing to do – and do enough of it that you will have time to finish your main project Do the next step of your next project – there might be a further step that can’t be complete immediately, in that case, wrap your work well and put onto the shelves. Letting your work rest for a while can really help keep your work clean and professional looking. Many things require bagging under plastic to keep it ready for work the next week – put your name on the outside of the bag so you can find your work easily. We have stickers and markers. Consider how you want to decorate your work – coloured slip can be applied at a fairly wet stage (remembering that it will make your work even wetter!). Trying to apply slip to dry clay won’t work! If you want to do sgraffito – you will need to keep the work leather hard (a state of dryness where you can still work the clay with a little effort and a little water and care). Step Three – Drying Most of the time your work can go into the rack uncovered to let it dry out for the following week. If you want to continue forming or shaping you will need to double bag your work – put your work on a suitable sized bat and put the bat in a bag so the base of the bag is under the bat, then put another bag over the top of the work and tuck the top of the bag under the bat. If you want to trim (or turn) your thrown work the following week, it should also be double bagged. If your work is large, delicate, or of uneven thicknesses, you should lightly cover your work for drying. When considering the drying process, bare in mind the weather, humidity and wind! The hotter and dryer, the faster things dry and work can dry unevenly in the shelves – this can lead to cracking – another time to lightly cover your work for drying. Step Four – Trimming and Cleaning Up Your work is dry! It is called greenware now and it is at it’s most fragile! Handle everything with two hands. I often refer to soft hands – keep everything gentle and with your fingers spread as much as possible. Try to not pick up things like plates too much, and always with both hands! Before your work can be bisque fired it should be “cleaned up”. You work won’t go into the kiln if it has sharp edges – when glazed, sharp edges turn into razor blades! Use a piece of fly wire to rub the work all over – this will scratch a little so be light handed. Use a knife or metal kidney to scrape any areas that require a bit more dynamic treatment than the fly wire offers! Finally, a very light wipe over with a slightly damp sponge can help soften and soothe all of your edges and dags! Trimming thrown work: If you are planning to trim (or turn) your thrown work (and you should be), make sure you bag it well – your work should be leather hard to almost dry for easiest trimming. Use this step to finish the work completely – use a metal kidney to polish the surface, or a slightly damp sponge to give a freshly thrown look. Wipe the sponge around the rim after trimming, and check the inside of the pot for dags! Trimming slip cast work: Usually I will trim the rims of your work on the wheel the following day to make that stage easier, however you will still need to check your work for lumps and bumps. Last but not least – check that your name is still clearly on the bottom of your work. Step Five – Bisque Firing When the work is completely dry it can go into the bisque kiln. The bisque kiln is fired to 1000°C. This process burns off the water in the clay as well as some of the chemically bound water. The structure of the clay is not altered that much at this temperature. Inside the bisque kiln, the work is stacked a little, small bowl inside a larger bowl and onto a heavy plate. Smaller items like decorations or drink coasters might get stacked several high. Consideration is paid to the weight of the stack and shape of the work. A bisque kiln can fire about one and a half times the amount of work that the glaze kiln can fire. The firing takes about 10 hours to complete the cycle and about two days to cool down. Once it has been emptied the work is placed in the glaze room ready for you to decorate! Step Six – Glazing Decorating your work with colour can be a lot of fun – and time consuming! There are three main options for surface treatment at this stage: Oxide Washes Underglazes Glazes Washes and underglazes do not “glaze” the work – It will still need a layer of glaze to fully seal the clay (washes don’t need glaze on surfaces not designed for food or liquid as they can gloss up a little on their own). Underglazes are stable colourants that turn out pretty much how they look in the jar. They can be mixed with each other to form other colours and can be used like water colours to paint onto your work. Mostly they should have a clear glaze on top to seal them. Oxides are a different species – the pink oxide (cobalt) wash turns out bright blue for instance. They don’t always need a glaze on top, and some glazes can change the colour of the wash! The glazes need no other “glaze” on top! Be careful of unknown glaze interactions – you can put any combination of glaze in a bowl or on a plate, but only a single glaze on the outside of any vertical surface! Glazes are a chemical reaction under heat. We don’t know the exact chemicals in the Mayco glazes we use. I can guess by the way they interact with each other, however, on the whole, you need to test every idea you have, and not run the test on a vertical surface! Simply put, glaze is a layer of glass like substance that bonds with the clay underneath. Clay is made of silica, alumina and water. Glaze is made of mostly silica. Silica has a melting point of 1700°C and we fire to 1240°C. The silica requires a “flux” to help it melt at the lower temperature. Fluxes can be all sorts of chemicals – a common one is calcium – calcium has a melting point of 2500°C, however, together they both melt at a much lower temperature! Colourants are metal oxides like cobalt (blue), chrome (green through black), copper (green, blue, even red!), manganese (black, purple and pink) iron (red brown), etc. Different chemicals in the glaze can have dramatic effects. for example, barium carbonate (which we don’t use) turns manganese bright pink! Other elements can turn manganese dioxide brown, blue, purple and reddish brown. Manganese dioxide is a flux in and of itself as well. So, glazes that get their black and purple colours, often interact with other glazes and RUN! Our mirror black is a good example – it mixes really well with many glazes because it fluxes them – causes them to melt faster. It will also bring out many beautiful colours in the glazes because it’s black colouring most definitely comes from manganese dioxide! Glaze chemistry is a whole subject on it’s own! We use commercial Mayco glazes on purpose – for their huge range of colour possibilities, stability, cool interactions, artistic freedom with the ability to easily brush the glazes on and ease of use. We currently have almost 50 glazes on hand! A major project is to test the interactions of all glazes with each other. That is 2,500 test tiles!!!! I’m going to make the wall behind the wheels the feature wall of pretty colours! Step Seven – Glaze (Gloss or sometimes called “Glost”) Firing Most of the time this is the final stage of making your creation (but not always!) The glaze kiln goes to 1240°C. This is called cone 6, or midrange. It is the low end of stoneware temperatures. Stoneware clays and glazes are typically fired at cone 8 – 10, that is 1260 – 1290°C. The energy requirement to go from 1240°C to 1280°C is almost a 30% more! Our clay is formulated to vitrify (mature, turn “glass-like”) at 1240°, as are our glazes. A glaze kiln take around 12 hours to reach temperature and two to three days to cool down. Sometimes a third firing process is required – this is for decoration that is added to work after the glaze firing. For example – adding precious metals and lustres. this firing temperature is usually around 600 – 800°C depending upon the techniques being used. There are many students interested in gold and silver trims – we will be doing this third type of firing soon! After firing your work will be in the student finished work shelves. Remember to pay for it before you head out the door! There is a small extra charge for using porcelain clay (it’s more than twice the price of regular clay), and for any third firing process! Once your work has been fired it can not turn back into clay for millennia – so don’t fire it if you don’t like it! Put it in the bucket for recycling. https://firebirdstudios.com.au/the-process-of-making-pottery/Ceramics have evolved over thousands of years.Earthenware dessert plate, cream colour. Made by Alfred Meakin, England. Backstamped ‘Alfred Meakin England’. flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, alfred meakin, ceramics, earthenware, kitchenware

Established by George Guthrie in 1857 (about 5km north of its current site) and then again seven years later in 1864 after it initially closed, Bendigo Pottery remains one of the most influential and longest running Pottery’s in Australia. Over the years the Pottery has contributed to the growth and development of the district through both its products including building products, table ware and decorative and commemorative war as well as artistically, being responsible for training and supporting many potters locally. The City of Greater Bendigo has had a long history of partnering with Bendigo Pottery and the Civic Collection holds a number of important items within its collection. This Alfred Deakin 'reform' flask was one of a limited edition character bottles produced by the Pottery to commemorate important figures in Australian politics. The original reform flasks were English salt-glazed stoneware flasks produced in the early 19th century shaped into the form of figures connected with the Reform Bill of 1832. Much was made of puns like ‘the spirit of reform’ at the time. Artist John Frith has taken the reform flask form as inspiration for a series of political ceramics of some Australian Prime Ministers. The series includes Edmund Barton, Alfred Deakin and Chris Watson.Glazed ceramic flask in the shape Alfred Deakin. Square shaped with most of the detail on the front facing side other than head which is more detailed. Cork still in place in top of head.On reverse of flask; Alfred Deakin / Prime Minister / of Australia / 1903 - 1904 / 1905 - 1908 / 1909 - 1910 Bendigo Pottery / LMTED / Edition Series / 101/200 /Australia Signed lower left; 'Frith'australian politics, bendigo pottery

"The Alfred Hospital was founded in 1869 as a result of the work of a number of Melbourne doctors who fought a long and internecine battle for an additional general hospital treating its first patient in 1871. Prahran Council donated a parcel of low lying land for the provision of a Hospital. In 1870, the Melbourne architect, Charles Webb, won the competition to design The Alfred Hospital with his revolutionary design. Webb incorporated the "Nightingale" design principles by designing large light filled pavilions as wards connected by covered corridors or walkways." (Alfred Health)Small colour print mounted on a wood block. Print depicts a series of five red brick buildings at centre, with a dirt road snaking up from the left foreground to the front of the central building. A man is driving a two horse buggy along the dirt road towards the buildings. The landscape on either side of the road consists of grassland and low vegetation, as well as four shallow circular pits (two on either side) which contain vegetation. There are two figures in the right foreground cutting grass with scythes. A flock of birds is visible in the sky in the central background, above the main hospital building. Text printed below image reads 'THE ORIGINAL DESIGN OF THE ALFRED HOSPITAL/By C.Webb, Arckitect (sic)'. The back of the wooden block to which the print is affixes is painted black, and a circular hook has been attached to the centre back of the block for hanging the artwork. The hook is gold coloured, and attached using two gold coloured pins and a small strap. Handwriting at bottom right of the back of the object reads 'ANN TAVELL''THE ORIGINAL DESIGN OF THE ALFRED HOSPITAL/By C.Webb, Arckitect (sic)'

George Hotelblack and white photograph, unmounted, good conditionInscription "Geoff Bull 03/03/81"

McGhie George & Isabelle photographed outside their Patrick Street house Stawell c 1900. Isabella McGhie born in Tain Scotland nee McDonald. Died 21.11.1914 aged 82. They were married at Ararat in August 1858. George was born in Orkney and died 20.5.1913 aged 88Black & White photo of George & Isabella Mc Ghie. George is seated and Isabella is standing with her arm on Georges shoulder. they are outside their Patrick St home. c 1900Printed on the back of the photo " George & Isabella McGhie Date not know, but estimate around 1900. Taken outside their house in Patrick Street, Stawell. Original held by Sue Goodluck, great-granddaughter of Wilhelmina McGhie, daughter of George & Isabella".stawell portrait

Alfred Deakin (3 August 1856 – 7 October 1919) was an Australian politician who served as the second Prime Minister of Australia, in office for three separate terms – 1903 to 1904, 1905 to 1908, and 1909 to 1910. Before entering office, he was a leader of the movement for Australian federation. (Wikipedia)Black and white image of Alfred Deakin.portrait, alfred deakin, prime minister

Alfred Deakin (3 August 1856 – 7 October 1919) was an Australian politician who served as the second Prime Minister of Australia, in office for three separate terms – 1903 to 1904, 1905 to 1908, and 1909 to 1910. Before entering office, he was a leader of the movement for Australian federation. (Wikipedia)Black and white image of Alfred Deakin.portrait, alfred deakin, prime minister

artist, architectural drawings, margaret picken, camberwell, housesartist, architectural drawings, margaret picken, camberwell, houses

A property illustration by Margaret Picken Commissioned by the real estate agency Woodards, Camberwell for the purpose of advertising 10 Alfred St., Burwood for sale in 1999. Made by using Rotring ‘Rapidigraph’ drafting pens with Rotring ink on Rapidigraph polyester drafting film, double matte. The suburb lines are believed to have been redrawn, making this property no longer in Burwood, but located in Glen iris. This property is listed as having sold for in 1999 for $380,000 Trained as a cartographic draftsman within the mining industry, Margaret Picken is an artist who worked producing property illustrations for real estate agencies in eastern suburbs of Victoria from 1983-2005. Retiring from the industry as technological changes favoured coloured photography over illustrations, and commissioning companies over sole contractors.This artwork is of Historical Significance as a record of local domestic architecture.A Black ink line drawing on drafters film by Maragret Picken, of 10 Alfred St., Burwood. Depicted is a one-story brick house situated back from a front lawn with a large tree, and a driveway on the right, leading to a connected carport. There to two hole punches just below the upper edge, and a approximately 1cmx1cm tape reside mark left of centre near the bottom edge 10 Alfred St., Burwood Maragret Picken - 99 Woodards - c'wellwhitehorse historical society, schwerkolt cottage, housing, architecture, margaret picken, burwood, glen iris, house, garden

The original of this portrait was painted by Max Meldrum in 1926. In 1934 the Ballarat School of Mines sought donations to purchase the portrait for the Art Gallery of Ballarat, where it is held today. Donations were handed by the Balllarat School of Mines Registrar, John B. Robinson. Professor Alfred Mica Smith was a famed professor at the Ballarat School of MinesFramed reproduction of a painting of Alfred Mica Smith. available, alfred mica smith, max meldrum, john b. robinson

Former SMB mining student Alfred Johnston was the son of Charles Johnston of Cork, Ireland, and Elizabeth Jameson, the family owning a large furniture store in Fitzroy. Alfred joined the Fifth Victorian (Mounted Riffles) contingent at the Melbourne suburb of Hawthorn. The October 1901 Ballarat School of Mines (SMB) Students Magazine reported 'Alf. Johnston's gone. The news came as a shock to all of us at the school. He who was with us a few short months ago, in all strength of sturdy manhood, has met a soldier's death in South Africa, and we sincerely mourn his loss…. His heart was in the school, and he did his best to further its interests … His last act on leaving Australian shores was to send a telegram from Albany to Prof. Mica Smith, to whom he was warmly attached, wishing the School and all connected with it "Good-bye". In his short, all to short, life of 29 years, he had more adventure than falls the lot of most men, and possibly the spirit of adventure, and also, of duty, prompted him to throw in his lot with the "colors," and leave for the front. The news of his death comes to us with added weight of sadness when we remember that he was one of the organisers of the School entertainment last year to help swell the fund for the erection of a statue to fallen Victorian soldiers.' The SMB Annual Report of 1901 recognised the loss of one of their students: 'Mr Johnston was, until the date of his leaving for active military service in South Africa, one of our students. While here besides being regarded as a general favourite for his urbanity and manliness, he was noted as a faithful, diligent, and most successful student. The news of Lieutenant Johnston's death cast quite a gloom over the school and it was early decided that in addition to a letter of condolence sent to his parents a bronze tablet, suitably inscribed, be erected to his memory in some prominent part of the school. On the 4th November last the ceremony of unveiling the memorial tablet was performed by Professor A. Mica Smith in the presence of several members of the late Lieutenant A.G. Johnston's family, the President and Members of Council, the Staff and Students of the School, and a number of prominent citizens.Brass shield used to commemorate the death of former Ballarat School of Mines graduate Alfred G. Johnston who died during the Boer War. In memory of Alfred G. Johnston Lieut. Fifth Regt V.M.R., and student of this school who fell at Rhenoster Kop, South Africa May 7th 1901 aged 29 years. An esteemed student and a gallant soldier.boer war, victorian mounted rifles, alfred johnston, memorial, rhenoster kop, south africa, south african war