Demonstrates uniform cap manufacture, badge and has a strong association with a former Ballarat Driver - Norm HuntSEC Motorman/Drivers/Conductors cap - green cloth exterior, grey cotton interior lining, brown leather internal hat band, black cotton hat band on exterior with a plastic band at the front half of the cap terminating in two small SEC metal buttons on either side, black plastic peak fitted with cap or badge No. 20, nickel plated silver, in the centre of the cap above the hat band. Sewn on the inside is a label "Commonwealth Government Clothing Factories Melbourne (very faded)" and stamped "6 3/4". See also Reg. Item 3044 for an ex Geelong cap. Stored with the cap are a copy of the SEC By-Law 1, August 1965 and the Federal Rules of the ATMOEA - 1969 and three SEC tickets.tramways, trams, uniforms, cap badge, cap

Yields information about the early staff of the Electric Supply Co. of Victoria following the electrification of the tramways and their appearance.Laminated Black and white print from a copy negative of a group of ESCO employees (motormen conductors and pointsboys?) in front of the tram depot with tram cars 17, 10 and 2 behind. All wearing uniform hats, but not all wearing full uniform (no badges but wearing ties - possibly temporary or casual staff - c1906 - 51 people. Print from a copy negative (N13), made early 1997 for display purposes and laminated. Has four Velcro dots on rear. Trams have destination boards fitted to the tram above the roof. 2nd copy - unlaminated added 29/7/2007 from Alan Bradley 5/2007. See also related documents for Museum Vic information on their copy. See reg item 8497 for a block mounted version.trams, tramways, esco, employees, group photo, tram 17, tram 10, tram 2

Cap or arm Badge for the Electric Supply Co. of Victoria (ESCo) "Conductor" with conductor staff number "17" Made from a manufactured and steel plate, nickel plated to indicate the staff number position held by the wearer as part of their uniform. Letters and number stamped, with horizontal lines. At each side of the badge are vertical holes through which light leather straps have been fixed with button holes to enable securing the badge on an arm. Leather straps black on one side and tan on the other. On the rear, silver soldered on are two loops at each end of the badge to enable badge to be sewn or fitted with clips onto the cap or the uniform. Badge appears in some photos of ESCo staff in the 1900's. On the back of the back of the badge in letters is the name of the manufacturer - "Stokes & Sons". Stored within tissue paper, within a heavy cardboard, Kodak Photo paper box.tramways, trams, cap badge, hat badge, uniforms, badges, esco

3044.1 SEC (Geelong) Motorman/Drivers/Conductors cap - green cloth exterior, grey cotton interior lining, brown leather internal hat band, black cotton hat band on exterior. Black plastic peak fitted with cap or with four holes for the employee badge number in the centre of the cap above the hat band. Sewn on the inside is a label "Commonwealth Government Clothing Factory Melbourne" and stamped "7 3/8". The plastic band at the front half of the cap terminating in two small SEC metal buttons on either side is not present. The holes for this are not visible - may not have been present on Geelong caps? 3044.2 - two small SEC Button badge - nickel plated silver with "Stokes" "Vic" stamped on rear. See also Reg. Item 2894 for a Ballarat Cap. On inside of leather hat band in ink "Mr. R. Evans" and "90 Albert St. West Geelong".tramways, trams, uniforms, cap badge, cap

Demonstrates uniform cap manufacture. Appears to be unworn.SEC Motorman/Drivers/Conductors cap - green cloth exterior, grey cotton interior lining, brown leather internal hat band, black cotton hat band on exterior with a plastic band at the front half of the cap terminating in two small SEC metal buttons on either side, black plastic peak. Sewn on the inside is a label "Commonwealth Government Clothing Factories Melbourne" and stamped "6 1/2". On the right hand side of the inside of the brown band, stamped in gold is the Australian Coat of Arms and the words "A quality product / made in Australia / by the Dept. of Supply". Appears never to have been used.tramways, trams, ballarat, uniforms, cap

Demonstrates uniform cap manufacture for a SEC Inspector, shows the "braid" worn by inspectors and has a strong association with Theo Dunstan.SEC Inspectors/Conductors cap - black cloth exterior, grey cotton interior lining, brown leather internal hat band, black cotton hat band with gold trimmings, on exterior with a plastic band at the front half of the cap terminating in two small SEC gold coloured metal buttons on either side, black plastic peak. Fitted with and "Inspector" cap badge - brass, has been polished with Brasso remains on interior of letters. Received from donor as three individual items - reassembled. Assumed made by the Commonwealth Government Clothing Factories Melbourne, as identical style to that of a crew cap.tramways, trams, ballarat, uniforms, cap, inspectors

Demonstrates uniform cap manufacture for a SEC Inspector and has a strong association with Theo Dunstan.A well used - SEC Inspectors/Conductors cap - black cloth exterior, grey cotton interior lining, brown leather internal hat band, on exterior with a plastic band at the front half of the cap terminating in two small SEC gold coloured metal buttons on either side, black plastic peak. Missing the Inspectors trip or "braid" Sewn to the inside top of the cap, a white label with red printing "Commonwealth Government Clothing Factories Melbourne" and stamped "6 5/8".tramways, trams, ballarat, uniforms, cap, inspectors

Demonstrates uniform cap manufacture, badge and has a strong association with a former Ballarat Driver - Jock Menzies.SEC Motorman/Drivers/Conductors cap - green cloth exterior, grey cotton interior lining, brown leather internal hat band, black cotton hat band on exterior with a plastic band at the front half of the cap terminating in two small SEC metal buttons on either side, black plastic peak fitted with cap or badge No. 60, nickel plated silver, in the centre of the cap above the hat band. Sewn on the inside is a label "Commonwealth Government Clothing Factories Melbourne" and stamped "6 3/8". See also Reg. Item 3044 for an ex Geelong cap.tramways, trams, uniforms, cap badge, cap

Demonstrates uniform cap manufacture for possibility a SEC Inspector.A used - SEC? Inspectors/Conductors cap - black cloth exterior, with a blue band on the edge red cotton interior lining, brown leather internal hat band, black plastic peak on the outside, green fabric on the inside. Note no holes in the side of the cap for the SEC cap band, but there are two holes in the top peak for a number or a badge. May not be an SEC cap, but the black decorative binding is the same as in the SEC Inspectors cap. There is the remnants of a manufacturers stamp on the inside red lining. tramways, trams, ballarat, uniforms, cap, inspectors

Copy of a colour slide showing Tram 42 in Lydiard Street North, at the terminus. This photo is taken from the north east looking down Lydiard Street. The conductor is adjusting the trolley pole it is preparing to head back into the city, and the destination board is reading Sebastopol. The shelter at the terminus can be seen, and there is a female passenger in hat and coat walking away from the tram. The photographer says this was taken on the last of the last tram to run in Lydiard Street in 1971. There is another photographer further down the street.trams, tramways, ballarat trams, crews, houses, last day, lydiard st nth, secv tramways, street scene, terminus, tramway closure, maximum traction, tram 42

Newspaper clipping from the Melton Moorabool leader, August 24. 2011, titled "Its hats off to Ryan", featuring BTM Conductor, Ryan Vanderzweep of Melton Mowbray College.btm, conductors

Illustration Black and white print of a group of ESCO employees in uniform in front of the tram depot with two tram behind. All wearing uniform caps except one wearing a straw hat. 35 men in uniform, one baby and in the back is a man not in uniform. Photo used in the 1986 - 1987 Annual Report on the rear cover. Original print not held by the Museum. Glenise Kellett advised 1/2020 that the man lying on the ground is Arthur Willem (Bill) Evan Gunn, tram conductor, buried 10/7/1919.trams, tramways, esco, employees, group photo

Black and white print from a copy negative of a group of ESCO employees (motormen conductors and pointsboys?) in front of the tram depot with tram cars 17, 10 and 2 behind. All wearing uniform hats, but not all wearing full uniform (no badges but wearing ties - possibly temporary or casual staff - c1906 - 51 people. Trams have destination boards fitted to the tram above the roof. See Reg Item 709 for a wider view. Yields information about the early staff of the Electric Supply Co. of Victoria following the electrification of the tramways and their appearance.Block mounted photograph with gold edges onto a heavy card back and foam with four holes with a support screw.esco, group photo, tramways, ballarat, employees, crews

Used by tramways to indicate the position of the person to a passenger or another employee. Most likely made as a general production item by Stokes for tramways and railways.Demonstrates an item made to indicate the wearer's position of the tramway employee.Uniform Badge for a "Conductor". Manufactured by Stokes and Sons, Melbourne. Made from a cast brass item and then nickel plated. Cast in the form of the handwritten or script word/s and underlined and rounded to fit on a cap. On the rear, silver soldered on are two brass loops at either of the badge to enable to be sewn or fitted with clips onto a cap. On the back of the back of the badge in very small letters is the name of the manufacturer - Stokes & Sons / Melbourne. tramways, trams, cap badge, hat badge, uniforms

BHS CollectionA tram conductor in tramway uniform, '9' badge on hat. Mounted in brown card folder. Possibly Basil Miller but not named on portrait.Reg V. Brock, Bendigoperson, individual, basil miller

1937 - Cap Badge for a "Conductor". Manufactured by Stokes and Sons, Melbourne. Made from a cast brass item, to indicate the position held by the wearer on their cap as part of their uniform. Cast in the form of the handwritten or script word/s and underlined. On the rear, silver soldered on are two brass loops at either of the badge to enable to be sewn or fitted with clips onto the cap. On the back of the back of the badge in very small letters is the name of the manufacturer - Stokes & Sons / Melbourne. Same manufacturers logo as in Reg Item 1940. Part of the ESCo company and possibly early SEC uniform. ESCo employee number on a special lapel bade - see Reg. item 1952. Not used by the SEC from 1940 - employee number on the cap but early SEC uniforms show them on the collar of the jacket - not known if this uniform adopted. See Reg. Item 1368 for photos of early SEC uniform showing badge on the neck. Assumed collected by Les from materials left over from the ESCo era in the SEC offices. 1937.1 - Item - as above, but nickel plated, with "Stokes" stamped into metal on rear of badge. Item ex SEC. Item 1937.1 added 2/1/05. tramways, trams, cap badge, hat badge, uniforms, esco

BHS CollectionBlack and white photo copy of No. 20 Electric Tram, ex Brisbane. Driver extreme right of photo, conductor 2nd from left. Man in hat on tram. On back written in blue ink 'Bendigo', ''The New Tram''- !!! Actually Brisbane No 20, suitably ''touched''. Copied from ''The Bendigonian'', 24/6/02, previously printed on 2/10/1900.'person, individual, basil miller

The Motorman or Conductor in winter uniform with SEC type number on his hat and a 3-button coat. The change in coat design would suggest that these photographs were taken in the late 1930s or in the 40s when uniforms would have been standardized across the three regional tramways in Victoria.Black and white print on paper.11-3 and GRS710/11/1/3 written on the reverse in pencil. No. 3 in a circle written on the reverse in pen.motorman, conductor, sec uniform c1930, tramway winter uniform c1930