Engine-Tangye's Patent size B engine 4 inch cyldiametre 8 inch stroke. 'Birmingham' painted green.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

The Davey Paxman Experimental Steam Engine was purchased as the result of a bequest from Thomas Bath. The 'substantial sum' was used to build an Engineering Laboratory. The Ballarat School of Mines Council minutes of 08 November 1901 record: - Plans for [the] proposed building were submitted ... and ... it was resolved that a temporary building for an Engineering Laboratory be put up.' This laboratory, as an existing building, is first mentioned in the Ballarat School of Mines President's Annual Report of 1901, presented on 28 February 1902, reporting 'the erection of a building 67ft long by 33 ft wide' This report also lists all the equipment that would be accommodated in the Engineering Laboratory, including the experimental steam engine and boiler. The experimental Davey-Paxman steam engine arrived in Ballarat towards the end of 1902. The Engineering Laboratory was opened on 14 August 1903 by His Excellency Sir Sydenham Clarke. This engineering laboratory remained in use till about 1945. By 1944 preparations were under way at the Ballarat School of Mines to expand existing facilities, to be ready for the influx of returned soldiers. A new Heat Engines laboratory was built, this time of brick construction, replacing the previous corrugated-iron shed. In the early stages the steam engine was used to drive an overhead transmission shaft for machinery in the adjacent workshop. Later the steam engine was moved to a space that became the Heat Thermodynamics Laboratory. At the end of 1969 the engine was relocated to the Thermodynamics Laboratory at the then Ballarat Institute of Advanced Education (BIAE) Mt Helen Campus. It was donated to Sovereign Hill in 2006. According to the research of Rohan Lamb in 2001 around five experimental steam engines were made by Davey Paxman, and three of these had similar configuration to the Ballarat School of Mines Steam Engine, however, each of these was also unique with different valve arrangements. The list, which was on a scrap of paper in a folio held in the Essex Archives, confirmed that one was sent to India. The Ballarat steam engine can be dated to late 1901 to early 1902. Zig Plavina was responsible for moving the steam engine to Mount Helen, and worked on it as a technician for many years. He observed the following: * The condenser is driven by the low pressure engine. * The following arrangements are possible: i) the high pressure engine alone, exhausting to atmosphere. Condenser not used, crankshaft flanges not coupled. ii) crankshafts coupled, mains pressure (120 psi) steam supplied to high pressure engine, partially expanded steam delivered to low pressure engine (Tandem operation). Choice available re exhaust steam: either to the condenser or to atmosphere. iii) crankshafts not coupled, reduced pressure steam supplied to low pressure engine. Exhaust steam - either to the condenser or to atmosphere. * Valve arrangement - a choice of Pickering cut-off or throttle governor. On low pressure engine - throttle governor only.Black and white photograph of the Davey Paxman Experimental Steam Engine. On the brake is returned serviceman Norman WIlliam Ludbrook (Diploma Electrical Engineering, 1952). Far right is Roy E. Mawby (Diploma Electrical Engineering, 1950)steam engine, model steam engine, davey paxman, electrical engineering, laboratory, scientific instrument, norman ludbrook, norman william ludbrook, roay mawby, roy e. mawby

Two ink plan drawings, one with brown and grey shading, showing proposed sites and relative positions for an engine house and engine. .1) shows Plan A and Plan B options .2) shows elevations of brick engine houseengine house, robert ditchburn, w. watson, plans, mining

The website: austinmemories.com provides a list of extracts from the Austin Motor company archive and makes mention that in WW2 some 3,500 lifeboats were provided for ships. In the link above there is also reference to airborne lifeboats. It seems that the Austin 8HP so-called lifeboat motor was very often re-used by boating enthusiasts which would account for the publication or e-issue? of this manual in 1986. It seems likely that this temperamental engine was still of interest to people like ship's engineers.Mariner Duncan had a particular regard for the Mission to Seafarers. This plate for display on a commissioned new table at the MTSV chapel acknowledges his bequest and the material donated. Collectively the G W Duncan material includes: photographs, professional data memorabilia and written and commercially printed resources. The memorabilia relates to his career at sea and in particular the role of an engineer, including a handwritten manual of notes and references relating to the mechanical and engineering aspects and areas of responsibility for maintenance. Commercially printed well handled small handbook or manual with rounded corners; for an Austin 8 HP engine for a lifeboat.see image for front cover mariner manuals, lifeboats, manual, motors, austin, george winfield duncan (1922-2017), ship engineer, s.s. athenic

Portrait of two gentlemen in suites seated in Cane Chairs. Jim Greenwood right (Engine Driver at 3 Jacks Mine) and his friend.A Sepia Photograph of two (2) seated males in cane chairs by a table, both dressed in suits, both with short haircuts.Herbert's Studio St (the rest is missing) in gold print on rear, in hand written script: Uncle Jim Greenwood right and his friend Engine drive at 3 Jack's Mine Stawellstawell, greenwood

Provides a report from The Age, 28-11-1989 written by Ingrid Swendsen, about the rejection by the Planning and Environment Minister , Tom Roper to protect the former cable tram winding or Engine house on the corner of Bridge and Punt Roads Richmond, despite the recommendation of the Historic Buildings Council to add it to the register. The building was later demolished by the Roads Corporation to widen the intersection. The Tramways have a small sub-station on the site. Quotes Douglas Hill of the National Trust and Roz Hansen of the Historic Buildings Council. Provides a report on the rejection of a recommendation to protect a historic building.Photocopy of a newspaper clipping from The Age 28-11-1989 - Roper rejects proposal to protect historic tram engine roomtrams, tramways, cable trams, engine house, winding house, punt road, bridge road, demolition, richmond, historic buildings council

K Class 157 Steam Train Engine pulling freight in cutting under Colquhuon Street bridge. Photo was taken from Hill Street Stawell around c 1962. Copy from original photograph of "K" Class 157 Steam engine pulling freight trucks going up the cutting and under the Colquhuon St. bridge. The rail line runs parallel to Napier St. c 1962. K 157.railways

Joel Joel Bridge Traction Engine Accident. Set of three photographs. C1922 Wimmera Bridge on Stawell Road. For information on accident see third SheetThree B/W photos of an accident on a bridge. A Traction engine broke through the surface of the bridge whilst towing a trailer full of lumber. the top photo is a close up of the tractor ashowing the rear wheel still on the bridge. The Second Photo shows the tractor and trailer from left rear, while the last phot shows the Secen from the right front.shire, archie slorach, joel area, john frampton

This engine was a Commonwealth Aircraft Corporation (CAC) build, and had been upgraded to 92 specification at some time. This engine as acquired, was completely seized and great difficulty was encountered in dismantling it. The pistons in Nos 1, 13, 3, 2 and 5 had "grown" into the cylinder bores requiring some unorthodox methods to remove them. The cylinder barrels have been brought up to a reasonable standard, those beyond repair were replaced from stock. After getting various parts from the US, this engine was eventually brought up to running order.The Pratt & Whitney R 1830 is a double row 14 cylinder air cooled radial engine with a capacity of 1830 cubic inches, (30 litres), developing some 1200 horsepower at a maximum 2700 rpm.Engine Number 54828

Engine steam operated large thin fly wheel and small wide fly wheel 710mmL x 360mmW. Bench mounted for running toolsflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Engine steam operated coal fired has large fly wheel painted green and red, mounted on wood 790mmH x 460mmW Circa 1880flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Completed by Glen Stuart in 2007 and published by PMH&PS in October 2008, when Glen spoke on the subject at a PMH&PS meeting"My Time At Engine Works" by Glen Stuart. Yellow paperback 48 pages illustrated. A memoir of Glen's working life, building marine engines.industry - manufacturing, transport - shipping, commonwealth engine works, glen stuart

Saw Bench - New Record Saw Bench Timber framed with steel wheels, belt driven saw blade powered by a Rosbery internal combustion engine. The Rosebery Engine No C28437 R.P.M 800 H.P. 6 Manufactured By Westinghouse Rosebery Pty.Ltd. Sydney Rosebery Engine Works Ltd began as the engine and pump manufacturing division of Buzacott & Company, and in 1923 became an incorporated company. In 1935, Westinghouse gave Rosebery Engine Works the right to manufacture and sell nearly all Westinghouse products. The name of the company then changed to Westinghouse Rosebery Ltd From the late nineteenth century, petrol engines gradually supplanted steam engines for running a wide range of machines, and in turn petrol engines were largely supplanted by electric motors. The Champion was a successful small petrol engine made by the large Sydney company, Westinghouse Rosebery, based on the American-designed Fuller and Johnson engine. With hopper cooling and a fuel tank between the skids, and weighing only 240 pounds (109 kg), it was easy to mount on wheeled transport, making the Champion a self-contained mobile source of power. Engines of this type were used in rural areas for driving chaff cutters, small saw benches, pumps and orchard sprayers. These engines were also commonly used in both rural and urban areas for powering concrete mixers. Both Westinghouse Rosebery in NSW and Toowoomba Foundry in Queensland made these engines in large quantities, beginning in the 1920s when tariff protection made local manufacturing viable. The production of small petrol engines continued in Australia until the 1970s, when reduced tariff protection led to increased competition from cheaper imported engines. Historic - Industrial Timber working - belt driven saw blade powered by a Rosbery internal combustion engine. Timber framed with steel wheels, belt driven saw blade powered by a Rosbery internal combustion engine. The Rosebery Engine No c28437 R.P.M 800 H.P. 6 Manufactured By Westinghouse Rosebery Pty.ltd. Sydneysaw bench, puffing billy, new record, internal combustioin, westinghouse rosebery pty.ltd., rosebery pty, internal combustion engine.

These log books would have been kept for each aircraft at the air stationHard back bound book 305 pages with columns. sections titled Chronological Log, Repair Log, Modification LogAero Engine Log Book, Type of engine-Cheetah BHP. 340. Series or Mk No. IX Makers number AS34299, A Number DG750, A 143950log book, aero engine log, repair log, anson, cheetah

Coloured photo of Diesel Engine in Blackburn Cool Stores.blackburn cool store, diesel engines

Coloured photo of Diesel Engine in Blackburn Cool Stores.blackburn cool store

This photograph was printed from a glass negative held in the Society's picture collection. The original glass negative is part of a set donated to the Society by Ian McKenzie, a professional photographer in Kew. Stationary engine, ca. 1900-ca. 1920. An early stationary engine that might have been used to drive a piece of immobile equipment, such as a pump, generator, or mill or factory machinery. stationery engine, glass negatives

Henry Sutton is a talented world-wide accepted inventor with inventions relating to the telephone, photography, wireless, cars, motorcycles, and bicycles as well as many more inventions. Henry was also one of four brothers that ran the Sutton's Music Store after the death of their Father Richard Sutton. Henry Sutton taught Applied Electricity at the Ballarat School of Mines in 1883 to 1886.Patent document relating to the Combustion Engine of Henry Sutton in 1899patent, victoria, henry sutton, combustion engine, c.n. dalton

Henry Sutton is a talented world-wide accepted inventor with inventions relating to the telephone, photography, wireless, cars, motorcycles, and bicycles as well as many more inventions. Henry was also one of four brothers that ran the Sutton's Music Store after the death of their Father Richard Sutton. Henry Sutton taught Applied Electricity at the Ballarat School of Mines in 1883 to 1886.A3 sized document relating to the patent of the "Combustion Engine" in NSWhenry sutton, patent, combustion engine, nsw, new south wales

General electric turboshaft engine fitted to Bell UH1 helicopter.aircraft engine, get58