House hold item, grinder for grain- coffeegrinder, coffee, ground, grind

A Berdan pan was a grinding pan. The circular pan was set at an angle, and as the pan revolved, a heavy iron ball rotated in the lowest point, grinding sand or mineral to a fine powder. It was frequently used to grind impurities out of amalgam (gold in mercury), and to grind batch-lots of heavy mineral. It is also known as a ball mill. Two strong wooden A frames supporting large iron pivotable bowl with a large iron ball inside the bowl. There are cogs underneath bowl which are connected to rotating belts extending from main battery shaft. The chute attached below the bowl is directed into a circular metal container. The frame is painted green.

Black enamelled cast iron mortar and pestle with mark on base of the letter C surrounded by star of David. Useed for grinding things to powder.Clark & Co No3 5 inchmedicine, pharmacy, mortar & pestle, k100.1.2

Grinding wheel, stone belt driven from the steam engine used for sharpening tools. Has a copper tub on top for water to run onto wheel.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, grinding wheel

Veterinary equipment. Although glass mortars and pestles are fragile, they are stain-resistant The substance to be ground is placed in the mortar and ground, crushed or mixed using the pestle. It would have been used to break up tablets. (identified by vet. Peter Honey) These items were found in an old walk-through dairy at Wombat Track near Orbost. These items are representative of items used in Orbost on dairy farms in the first half of 20th century.A mortar and pestle. The mortar (2397.1) is a shallow bowl. The pestle (2397.2) is a blunt club-shaped object, the end of which is used for crushing and grinding. Both are made of glass.veterinary-equipment mortar-pestle dairy farming

interior view of grinding shopblack and white photograph

The State Electricity Commission of Victoria produced and displayed safety signs for their employees during the construction of the Kiewa Hydro Electric Scheme.KHES was constructed from the late 1940s to early 1960s and included the construction of Mt Beauty and Bogong townships. Safety was a concern for the SECV towards its workers. Metal black print on white background with yellow 'emphasis' at the top - 'Safety'. "Instructions for the use of / Grinding Wheels". There is a circular hole in each corner with a black frame around the perimeter.state electricity commission of victoria, kiewa hydro electric scheme, safety sign, grinding wheels

Owned and used by the late Mr W.T. Sebire 1900. The frame was rebuilt by Russell Sebire.A large sandstone grinding stone disc with a pale blue wooden frame and metal turning handle/ It was used for sharpening tools such as axes in the late 19th or early 20th Century. grinding stones, sandstone, equipment, sharpeners, sharpening stones, steel, wood

This grinding stone (mortar) was used by Aboriginal people to grind or crush different materials such as berries and seeds for food production. In order to grind material, a smaller upper stone (the pestle) would have been used to grind material against this lower stone (the mortar). The stone was found by a farmer on land south of Donald in the 1950’s and was used as a door stop in the family home for many years. In the 1990's the stone was used by the farmer's grandaughter at her home at Swanwater West, to hold the lid down on an above ground swimming pool skimmer box. Stone

This item is from the ‘Pattison Collection’, a collection of books and records that was originally owned by the Warrnambool Mechanics’ Institute, which was founded in Warrnambool in 1853. By 1886 the Warrnambool Mechanics’ Institute (WMI) had grown to have a Library, Museum and Fine Arts Gallery, with a collection of “… choice productions of art, and valuable specimens in almost every branch and many wonderful national curiosities are now to be seen there, including historic relics of the town and district.” It later included a School of Design. Although it was very well patronised, the lack of financial support led the WMI in 1911 to ask the City Council to take it over. In 1935 Ralph Pattison was appointed as City Librarian to establish and organise the Warrnambool Library as it was then called. When the WMI building was pulled down in 1963 a new civic building was erected on the site and the new Warrnambool Library, on behalf of the City Council, took over all the holdings of the WMI. At this time some of the items were separated and identified as the ‘Pattison Collection’, named after Ralph Pattison. Eventually the components of the WMI were distributed from the Warrnambool Library to various places, including the Art Gallery, Historical Society and Flagstaff Hill. Later some were even distributed to other regional branches of Corangamite Regional Library and passed to and fro. It is difficult now to trace just where all of the items have ended up. The books at Flagstaff Hill Maritime Village generally display stamps and markings from Pattison as well as a variety of other institutions including the Mechanics’ Institute itself. RALPH ERIC PATTISON Ralph Eric Pattison was born in Rockhampton, Queensland, in 1891. He married Maude Swan from Warrnambool in 1920 and they set up home in Warrnambool. In 1935 Pattison accepted a position as City Librarian for the Warrnambool City Council. His huge challenge was to make a functional library within two rooms of the Mechanics’ Institute. He tirelessly cleaned, cleared and sorted a disarrayed collection of old books, jars of preserved specimens and other items reserved for exhibition in the city’s museum. He developed and updated the library with a wide variety of books for all tastes, including reference books for students; a difficult task to fulfil during the years following the Depression. He converted all of the lower area of the building into a library, reference room and reading room for members and the public. The books were sorted and stored using a cataloguing and card index system that he had developed himself. He also prepared the upper floor of the building and established the Art Gallery and later the Museum, a place to exhibit the many old relics that had been stored for years for this purpose. One of the treasures he found was a beautiful ancient clock, which he repaired, restored and enjoyed using in his office during the years of his service there. Ralph Pattison was described as “a meticulous gentleman whose punctuality, floorless courtesy and distinctive neat dress were hallmarks of his character, and ‘his’ clock controlled his daily routine, and his opening and closing of the library’s large heavy doors to the minute.” Pattison took leave during 1942 to 1942 to serve in the Royal Australian Navy, Volunteer Reserve as Lieutenant. A few years later he converted one of the Museum’s rooms into a Children’s Library, stocking it with suitable books for the younger generation. This was an instant success. In the 1950’s he had the honour of being appointed to the Victorian Library Board and received more inspiration from the monthly conferences in Melbourne. He was sadly retired in 1959 after over 23 years of service, due to the fact that he had gone over the working age of council officers. However he continued to take a very keen interest in the continual development of the Library until his death in 1969. The Pattison Collection, along with other items at Flagstaff Hill Maritime Village, was originally part of the Warrnambool Mechanics' Institute’s collection. The Warrnambool Mechanics’ Institute Collection is primarily significant in its totality, rather than for the individual objects it contains. Its contents are highly representative of the development of Mechanics' Institute libraries across Australia, particularly Victoria. A diversity of publications and themes has been amassed, and these provide clues to our understanding of the nature of and changes in the reading habits of Victorians from the 1850s to the middle of the 20th century. The collection also highlights the Warrnambool community’s commitment to the Mechanics’ Institute, reading, literacy and learning in the regions, and proves that access to knowledge was not impeded by distance. These items help to provide a more complete picture of our community’s ideals and aspirations. The Warrnambool Mechanics Institute book collection has historical and social significance for its strong association with the Mechanics Institute movement and the important role it played in the intellectual, cultural and social development of people throughout the latter part of the nineteenth century and the early twentieth century. The collection of books is a rare example of an early lending library and its significance is enhanced by the survival of an original collection of many volumes. The Warrnambool Mechanics' Institute’s publication collection is of both local and state significance. The Remains of Edmund Grindal, D.D. Successively Bishop of London and Archbishop of York and Canterbury Edited for The Parker Society by Rev. William Nicholson Publisher: Cambridge University Press Date: 1843 Label on spine cover with typed text PAT 252 GRI Pastedown end page has sticker from Warrnambool Mechanics Institute and Free Library Front loose endpaper has a sticker from Corangamite Regional Library Servicewarrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, shipwrecked-artefact, book, warrnambool mechanics’ institute, pattison collection, warrnambool library, ralph eric pattison, warrnambool city librarian, mechanics’ institute library, victorian library board, warrnambool books and records, warrnambool children’s library, the remains of edmund grindal, rev. william nicholson, the parker society

Cast iron meat mincer/food chopper. Patent Oct.12, 1897 Apr. 18, 1899 Re Sept. 5, 1899 Only one grinding plate - attached.Name of maker and above dates.food chopper, meat mincer, l f & c

Memorandum, typed foolscap, 4 sheets, titled "Notes on Rolling Stock Maintenance Practice", undated, late 1930's? looking at MMTB Workshop and depot maintenance practices, for tramcars. Gives details of the shifts, cleaning, motor inspections, grinding, the use of a single truck breakdown tram, grinding of wheels at depots, annual mileages, defect rate, use of roller bearings on armatures, painting of trams, gear shield grease and varnishing or lacquering of seats and interiors,trams, tramways, tramcar components, brakes, depots, workshops, maintenance, motors, rolling stock, bearings, paint

Cups of this type were often used in pharmacies for grinding powders/medicinesBrass cup with handle on each side.brass, grinding cup, pharmacies, handled cup, measure

Appears to be a millstone that would have been used with another stone to grind wheat.Large circular stone wheel with ridges carved into its outer side. It has a hole through the middle with a metal fixture in it.

Grinder for grain, metal with square grain holder situated on top of grinding mechanism with turning handle. Made by "THE ARCADE MFG CO FREEPORT ILL. USA. Has "No 1 Patent Apld. For" stamped on front.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

This domestic appliance is typical of the period when food processing was done at home. It would have been before the time of mass food processing factoriesBlack metal grain grinder. Top slides off to collect the ground grain. Opening at top to pour in grain. The back has holes to screw or nail to bench. There is a long grinding arm of metal with a wooden handle.Underneath -3 Under storer - T&C Clark & Co - Wolverhampton Bottom of handle - Clark & Cogrinder food-preparation domestic clark-t&c

This large and very heavy stone was donated by Albert Emphield. Where he found it is unknown, but he worked in the Orbost forest areas and lived at Cabbage Tree Creek.Aboriginal usage, tool manufacture.A large rock of generally oval shape and with a number of flatish surfaces and hole indentations which were identified by archaeologist Dr Joanna Freslov 2.6.2008 as being used by Aboriginal people as a grinding or tool-sharpening stone.aboriginal-grinding-stone

This object was used for grinding coffee beans. Originally purchased by Susan Barnett for $2.50 in an 'OP' shop.A honey coloured wooden coffee grinder with a metal lid and a red handle.BE/ (insignia in centre of a dog straddling a globe) / HA / GESCHMIEDETES MALHWERKdrinks, coffee grinder, dink comsumption, george evans collection

Advertising brochures for Linishall Multi-Purpose Abrasive Belt Grinding Equipment and Loroch Automatic Saw Sharpener.2 pamphlets text and colour illustrationsmachinery, tools

Diggers & Mining. Diggers and Miners. . . . . To the water-driven wheel, which drove grinding pans. These grinders further crushed the tailings and the remaining gold was extracted. Markings: 43 994.5 WAL. Used as a teaching aid. Used as a teaching aid.hanimounteducation, tertiary, goldfields

Cast iron pestle is heavy an brings substantial weight to the task of grinding and crushing dry and fresh spices, seeds, medicines and pillsUsed by the residents of the Kiewa Valley for grinding and crushing.Cast Iron large pestle. Solid and heavy.cast iron pestle

Cooper S.E. Ball Bearing Grinder made and guaranteed by Sunbeam Corporation Limited. Grinders like this example have been made the same since the early 1900s, with this grinder thought to have been produced in the 1960s. It is belt driven, with the other end of the belt being attached to an engine; the same engine that would have powered the overhead shearing equipment in shearing sheds. It was common for shearing teams to bring their own equipment, especially pre-1960 as most shearing sheds were not connected to power, and shearers preferred to work with their own equipment. The engines that powered the shears and grinder were typically fuelled with kerosene or petrol. The large circular disks are attached to the bolt that protrudes from the grinder and fastened tightly with a nut. An example of seeing a similar grinder in action can be found on the following link - https://www.youtube.com/watch?v=O7eimI_Gm9o. Inventor Frederick Wolseley made the world's first commercially successful power-shearing system in Australia in 1888. US company Cooper, which had been founded in 1843 as a maker of sheep dip, began selling Wolseley equipment in the USA in 1895. The Chicago Flexible Shaft Company successfully entered the power-shearing market a few years later and entered a joint venture with Cooper. It set up a branch in Sydney and sold shearing sets, and engines to power them, into the Australian market. In 1921 the US parent company, realising it needed to make products whose sales were not as seasonal as those of shearing equipment, made its first household appliances and branded them Sunbeam. In 1933, changes in exchange rates and taxes led the company to manufacture engines and shearing equipment in Australia via subsidiary Cooper Engineering, which changed its name to Sunbeam in 1946. Although most Australians know of this company as a major manufacturer of household appliances, its rural division flourished and retained the Sunbeam name for shearing equipment even after it was taken over by New Zealand company Tru-Test in 2001. The grinder is formed from a central arch shaped block of green painted metal. Much of this paint has been lost to age, leaving the grinder in a ‘farm used’ condition with much surface oxidation present. On the front of the arch is a specification plate, reading “Cooper S.E. ball bearing grinder. Made and guaranteed by Sunbeam”. At the foot of the arch, three bolt holes are found for securing the grinder to the base of a solid wooden surface. Two of the bolt holes are found on the front of the grinder, with another found on the rear. From the central arch, a bolt protrudes to the right of the grinder. This large bolt is for securing a grinding plate to the grinder. Above the central arch is a pendulum which holds the comb / cutter that is being sharpened. From the pendulum, a large arm extends down (not pictured) to meet and strike the plate spinning at a rapid speed. On the left-hand side of the central arch of the grinder, a wheel is found which a belt is attached to for power. This belt is then attached to a separate engine, spinning the wheel and hence powering the grinder. The wheel is partially covered with a section of protective bent tube, designed to provide protection from the rapidly spinning wheel. Below this wheel is the belt shifter. It is designed to move the protective bent tube from one side of the grinder to the other, to accommodate the grinder in the setup of different shearing sheds. The two separate grinding plates are identical. They have a slight slope for sharpening the comb and cutters in the correct method, with a slight bias towards the base, or “tooth”, of the equipment. The disks have a large central bolt for attaching to the grinder. They have tags on the horizontal axis of the grinding plates, for securing the plates in transportation, and to help with initial alignment when setting up the grinder. The reverse of these grinding plates has the same green painted metal finish found on the grinder. This paint is also in a ‘farm used’ condition, with surface oxidation present. The grinder would be provided from the factory with a comb holder, shifter for securing the grinding plates, emery cloth and emery glue. The emery cloth is what does the actual grinding and is applied to the grinding disks, replacing once well worn. These items can be seen in the final images in the multimedia section, showcasing advertising for this grinder. Plate. Inscribed. “Cooper / S.E. BALL BEARING GRINDER / MADE AND GUARANTEED BY / Sunbeam / CORPORATION LIMITED / SYDNEY MELBOURNE / ADELAIDE BRISBANE ”sheep shearing, shearing equipment, sunbeam, grinder

Owned by Mrs Leach9cm mouth grinding chamber 11cm long mince exit diameter disc with exit holes and warning to screw this ring up tight. 11.5cm worm to mince the meat controlled by 16cm handle. Another screw moves to hold the mincer to the kitchen table.Enterprise, on chamber: tinned meat chopper No 5; on clamp: MF'G. CO. Phila. U.S.A..domestic items, food preparation

"Textile Machinery Specialities" - Dronsfield Bros Ltd, Atlas Works, Oldham, England, 13th ed. 1924. Catalogue for grinding machines and card making machines.textile machinery, dronsfield bros ltd

Sharpening is done by grinding away material on this implement with an abrasive substance harder than the material of the tool to be sharpened. A sharpening wheel is an efficient way to sharpen blade edges.Mobile knife-sharpening services are no longer commonly used. In the disposable society of the 21st century we can throw away our blunt scissors, knives or tools and buy replacements.A cast iron knife or tool sharpening wheel attach to a wooden base. It has a wooden turning handle.A McMillan Federal Knife Cleanerknife-grinder

The site includes a Hoffman kiln, clay mill building, grinding pans and brick presses, relics of the downdraught kiln stack, office, former locomotive shed, and quarry.The buildings of a brickworks in Box Hill, Victoria.box hill, surrey, surrey drive, brickworks, factory, industrial heritage, ruin, standard brickworks

This item is representative of grinding stones used throughout Australia to enable people to maintain farm and domestic utensils.A large circular grinding stone with metal handle. It was used on a stand and also with water to shapen blades such as knives, axes and hand shears. The wheel is a large cirle of sandstone. These were common in the late 19th and early 20th Century. It would have been used on a wooden frame.domestic tools, household utensils

John Berrill & Sons pigment grinder was patented in NY c1860. It was used to grind down pigment to mix with linseed oil, to make paint, before commercial paints became availableCast Iron pigment mill. "J. Berrill, Mfg. Waterville, NY"pigment grinder, painting, painting and decorating, trades, tools, j. berrill, john berrill and sons