The Improved Martin-Adelphi Anchor. The introduction of cast steel in 1894 led to the improved Martin-Adelphi pattern, in which the crown and arms are cast in one, and, with the stock, are made of cast steel, the shank remaining of forged iron. A projection in the crown works in a recess (right image), and is secured in its place by a forged steel pin, fitted with a nut and washer, which passes through the crown and the heel of the shank.Stock-anchor - improved Martins patent, Adelphi pattern improved Martins patent anchor, Adelphi pattern

This knife and scabbard belongs to Lindsay Fankhouser, who wore it on his ankle when he served as an engineer/ crewman in the RAAF (Iroquois and Hercules) during the Vietnam war. He used this knife many times a day while he was serving. It is a brown leather knife sheath, with a decorative front and two canvas straps attached at the back. The shorter strap is located at the bottom of the sheath and the longer strap is located just below the belt loop. Both straps are fixed in place with stitching. The top strap has a square of stitching, while the bottom strap has two lines of stitching that follows the stitching of the sheath. The belt loop is at the top of sheath and is a fixed flap of leather that is folded across the top and also holds the handle of the knife in place using a circular hole that fits around the butt of the knife. The bottom canvas strap has three adjustable brass male press studs on the left side as well as the fixed female one on the right. The top canvas strap has four adjustable brass male press studs on the right side as well as as the fixed female one on the right. The sheath is held together by stitching and five iron rivets. There is one on the point of the sheath, two on either side of the top, and two more 51mm below the top two. 46mm above the sheath, there are another two iron rivets on either side. Above that on the holding flap, there are two iron rivets just above the circular hole on either side. On the flap, around the hole there are three brass flat-headed split pins, one on either side and one on the front. At the top of the sheath, above the decorative embossing, there is a dark brown jagged cut strip of fixed leather. All the leather on the object is a reddish-brown, while the canvas and stitching is light beige. The end stitching on the canvas straps is dark grey. The front of the sheath is polished leather, while the back is rough.On back of belt loop flap, there is an embossd manufactuing patent number; PATENT Nr152.463 On face of the sheaf there embossed decoration. It depicts a lion with stylised decorative foliage and above the lion there is a fleur de lise. Above that it reads Soallingen Norge.norway, norge, soallingen, knife, small knife, hunting, scabbard, sheath, vietnam, lindsay fankhouser, raaf

See image 2085i4 for tender re brake blocks detailing the type of cast iron and the Brinell hardness.Demonstrates MMTB tender documents of 1923.Manila colour file marked "Specifications" containing 25 different specifications of the MMTB 1922 to 1925. Not all dated, generally foolscap sheets either pinned or stapled. Dated Tender No. For supply of: 30/6/1925 157 Steel castings Not dated Ballast Hopper trucks 1923 Steelwork for electric and cable tramway crossings Pamphlet Monier Pipes and box culverts Pamphlet Monier – septic tanks and aerators Not dated 229 Purchase of removal of cottages 101 to 107 Bouverie St Carlton Not dated Side tipping ballast trucks 18/7/1923 226 Brake shoes - see pdf file for a full scan 18/7/1923 222 Steel tramway tyres 18/7/1923 220 Concrete Mixing Plants Not dated 219 Dressed wooden poles 9/5/1923 215 Bricks 19/4/1923 214 Reinforced Concrete fencing posts 20/3/1923 213 Tramway steel wire ropes 28/3/1923 212 Painting exterior of 673 Bourke St Melbourne Not dated 210 Alterations to offices at Rathdowne St depot Not dated 202 80lb steel rails and fishplates 5/1/1923 198 GE201 Motors 6/12/1922 197 Hydraulic pit jacks 6/12/1922 195 Supply of Low tension feeder cable Not dated 194 Supply of high tension cable 4/12/1922 188 Supply of hard drawn trolley wire 6/11/1922 186 Dressed wooden poles 20/11/1922 182 Steel Poles 20/12/1922 171 Erection and completion of new car depot Glen Huntly Roadtrams, tramways, mmtb, tenders, specification, trackwork, motors, cables, poles, ballast wagons, glenhuntly tram depot, brake blocks

Photograph, copy print of an old photograph of conductor John McMahon in cable tram uniform with tickets pinned to his jacket along with other items alongside another cable tram crewman (grip man or another conductor - has large pins on his uniform and has the same bag over his shoulder) with a Brunswick depot / route cable tram set in the background. Advised by the donor that the photograph was taken c1923 at the Haymarket - thought to actually be at the Brunswick depot - the iron bars of revenue office. Printed AGFA photo Sensatis paper.trams, tramways, cable trams, mmtb, conductors, brunswick, haymarket, uniforms

Set of two tender documents, each of two foolscap sheets for the supply and delivery of castings to the Boards repair shops (Nicholson St or Holden St?), with patterns supplied by the Board. Gives details of the quality, approx. quantity, patterns, delivery, rejection, payment, cancellation and other details. .1 - "Manufacture, supply and delivery of iron castings contract No. 96" - 70 to 85 tons /half year - tenders closed 29/4/1929. .2 - "Manufacture, supply and delivery of steel castings contract No. 96" - 50 tons / year - tenders closed 10/6/1920. 2 copies of each, either pinned or clipped with a brass clip in top left hand corner.trams, tramways, tenders, contracts, mmtb, cable trams, castings, brake blocks

A Dray is a type of dead axle wagon that was used to transport heavy loads or objects. They had a flat level floor and while some had no sides, others had box bodies and sides. Tip Drays (also known as Tip Carts, Muck Cart, Scotch Cart, Tumbrel or Putt in different parts of England) were smaller than other drays as their loads were heavy and usually only pulled by one horse. Their basic design included two wheels, a tipping body and shafts. The Tip Dray has a unique mechanism that allows the top to tip backwards to tip the load out of the back of the dray. The tipper was activated by a handle at the front allowing the driver to operate it while still having control over the horse. A Tip Dray was an indispensable piece of equipment in the days before tractors and mechanical trucks. They were used by farmers and carters to transport hay, rocks, bricks, gravel and rubbish etc. and because they were useful for dumping loads, they were favoured for use in road and railway construction. A photo in the collection of the Lorne Historical Society shows a tipping dray being used during the construction of the Great Ocean Road. They were part of the daily street traffic in towns and cities around Australia from the early days of settlement. In Australia in the early 1900's, carters began to join unions to protect their jobs and pay. N.S.W. had a "Trolley, Draymen and Carters Union", Queensland had a "Tip Dray Men's Association" and in W. A. the "Top Dray Driver's Union" had a "cessation of work" in 1911 when they were fighting for an increase in their day's wages. In 1910 a meeting of Tip Carters was held in Geelong at the Trades Hall to discuss the formation of a union (The Geelong Tip Dray Carters) which was a success and a schedule of rates for all carting, whether by contract or day labor, was fixed. By 1912 they had "labelled" more than 50 drays and had representatives on the "Trades Hall and Eight Hours Committee". By the mid 1930's and early 1940's, tip drays were being superseded by mechanical trucks and utes. However tip drays continued to be used in some circumstances. They were a practical solution to the problem of petrol rationing during W. W. 2. It was noted in a letter to the editor in the "Sunshine Advocate" in 1938 that a positive argument for continued use of Tip Drays for rubbish collection related to the idea that a horse drawn vehicle involved with lots of stops and starts at different houses (very like a milkman's delivery route) often involved the horse "driving itself" while the driver picked up the rubbish - something a motor truck was unable to do! Another article written in August 1935 and published in the Age in a parliamentary report into the rubber industry noted "tip drays had almost disappeared and in their place, metal was carted in 5 ton motor trucks" but the report went on to say that as a part of the Government relief work (during the Great Depression) the Government had "to some extent reintroduced the tip drays so that a greater number of men would be employed". This particular tip dray was owned by Mr. Oswald (Jack) Bourke. He used it to deliver dry goods from Sunbury to the Queen Victoria Market in Melbourne several times a week in the 1930's and then (between 1945 and 1962) Mr. Bourke used it on the garbage round in Springvale Victoria for the Springvale Council. The Council owned three drays and the "No. 3" painted on this dray is in recognition of its original number. After the death of Mr. Bourke in 1990, one of Mr. Bourke's sons (Andy) found the dray in a shed and restored it. The sign writing on the back and side panels were added during the restoration. This Tipping Dray is a significant example of a horse drawn vehicle that was used by workers from the early days of white settlement through to the 1940's and even into the early 1960's. It was used in a range of "working class" occupations - road construction, railway construction, carting goods, rubbish collection etc. and would have been found in cities, country towns and on farms.A wooden and metal tipping dray with a box body and four sides. It has two iron and wooden wheels (with 14 spokes), two wooden shafts and a metal tipping mechanism. The back panel folds down to allow loads to be dumped out. It is painted in green and cream with sign writing on one of the sides and on the front and back panels. It features decorative painted lines and designs in burgundy, cream and light blue on most of the wooden parts. The tipping mechanism is on the front of the dray's left side and consists of a metal pin secured with a metal ring, and a lever.Front of dray - "No. 3" Side of dray - "A. & M. BOURKE / Contractors / LONGWARRY" Back of dray - "G.T. ANDREWS / QUEEN VICTORIA MARKET - Stand C23 / Phone DANDENONG 225"flagstaff hill maritime museum and village, warrnambool, shipwreck coast, tipping dray, dray, tip dray, tip cart, vehicles, horse drawn vehicle, springvale council, jack bourke, muck cart, scotch cart, tumbrel, putt, box body, oswald bourke, sunbury, queen victoria market, melbourne, no. 3