Showing 107 items
matching straight blade
-
Royal Australian and New Zealand College of Obstetricians & Gynaecologists (RANZCOG)
Boyle Davis mouth gag used by Dr Lorna Lloyd-Green
... to be attached and withdrawn. The tongue depressor is a straight metal.... The instrument is assembled by sliding the tongue blade into the frame ...This instrument is part of the tonsillectomy set. Mouth gags are used to keep the patient’s mouth open during oral surgery, leaving both hands of the surgeon free to operate. The Boyle Davis mouth gag consists of the Davis gag, a frame that serves to hold the mouth open and the Boyle tongue depressor to hold the tongue down. The tongue depressor comes in several sizes, from pediatric to adult. The instrument is assembled by sliding the tongue blade into the frame. The mouth gag is held in position using the Draffin bipod stand. (Entworld)White metal mouth gag [254.1] and tongue depressor [254.2] set. There are small leather fittings on the ends of each item. The mouth gag is roughly horseshoe shaped and attached to a metal support with a small lever, which also allows the tongue depressor to be attached and withdrawn. The tongue depressor is a straight metal blade which is bent and curved at either end. -
Geoffrey Kaye Museum of Anaesthetic History
Blade, Laryngoscope, Magill
... Magill straight laryngoscope blade with tubular space... IN ENGLAND Magill straight laryngoscope blade with tubular space ...Magill straight laryngoscope blade with tubular space for a light bulb connection (no light bulb is present). It is a PENLON piece, made in England. Size 1, for infant use. Has a slight yellowish discolouration over its base. General scratches around the base of the blade and a sticky old mark bellow an engraved inscription. It has engraved the name of the hospital where it came from and the initials of its owner.Engraved under the blade arm base the name, Royal Childrens Hospital Engraved in its lateral side attachment base piece the initials, D. A. Stamped at the back of the attachment base piece the type and size, MAGILL / 1 Stamped in its lateral side attachment base piece the trademark name and its made place, REG [is not visible the continuation] / PENLON / MADE IN ENGLANDmagill, blade, royal childrens hospital, metal, d.a. -
Geoffrey Kaye Museum of Anaesthetic History
Blade, Laryngoscope, Soper, circa 1947
... A Soper straight laryngoscope blade adult size with bulb... St Kilda Road Melbourne melbourne soper laryngoscope blade ...A Soper straight laryngoscope blade adult size with bulb only. The blade has minor scratches over its surface and below the arm's blade because of its use. Presence of an old sticky tape mark under the blade. The contact stud at the base of the blade is worn. The end of the blade has a perforated line as part of its design. The metallic base of the light bulb has an oxide spot on it. No inscriptions. No inscriptionssoper, laryngoscope, blade, adult, light bulb -
Forests Commission Retired Personnel Association (FCRPA)
Adze - small
... parallel. The wooden handle is straight and the blade has a slight.... The wooden handle is straight and the blade has a slight curve ...An Adze is versatile cutting tool similar to an axe but with the sharp cutting edge perpendicular to the handle rather than parallel. The wooden handle is straight and the blade has a slight curve. They are used for smoothing or carving wood such as sleepers An adz, with its long handle, cuts with the grain, and the nature of the chips is different from an axe. While they have a similar shape, they should never be confused with a hoe or mattock used for agriculture and horticulture. Adze - smalltimber tools -
Geoffrey Kaye Museum of Anaesthetic History
Laryngoscope, Macintosh
... blade, most laryngoscope blades were long and straight... and straight. The straight blades were used to directly hold ...A laryngoscope is an instrument used to view the larynx (voice box), which is the opening to the trachea and lungs. It consists of a “blade,” which goes into the patient’s mouth, and a handle. Prior to 1943 when Macintosh introduced his curved blade, most laryngoscope blades were long and straight. The straight blades were used to directly hold the epiglottis. Macintosh’s curved blade works differently: it indirectly opens the epiglottis by applying pressure to a space between the root of the tongue and epiglottis, called the vallecula. The flange running along the left lower edge of Macintosh’s blade was also a novel innovation. It was designed to move the tongue to the side, which improved the view of the larynx and made more room for a breathing tube. The Macintosh Laryngoscope remains one of the most popular blades worldwide. (Source: Wood Library Museum) This laryngoscope was previously owned by John Mainland, as evidenced by the name etched into the handle. Mainland graduated from the University of Melbourne in 1950 with a Bachelor of Science degree. After researching and completing his medical degree, Mainland entered into the field of anaesthetics, training at the Royal Women's and Royal Children's Hospitals, later Alfred Hospital, in 1959. He completed training in 1964 and remained at the Alfred Hospital. During his career, he also became the first anaesthetist appointed to the position of Professor in Victoria. His other achievements include manufacturing a respiratory monitoring module that accompanied astronauts on the United States moon landing and developing a stimulator to lessen the risk of deep vein thrombosis in surgical patients. Mainland became a Fellow of the Australian and New Zealand College of Anaesthetists in 1992, retiring from the profession in 1997.Oblong shaped handle with textured grip. Attached is a laryngoscope blade in a cruved shaped with light tube running through one side.Etched into top of handle: J.F. MAINLAND •Stamped into top of handle: REGD TRADE MARK / PENLON / MADE IN ENGLAND •Stamped into base of handle: CLOSE [arrow] •Etched into base of blade: MAC / 4 •Stamped into side of blade: REGD TRADE MARK / PENLON / MADE IN ENGLAND •Stamped into side of blade: STAINLESSmacintosh, robert reynolds, new zealand, laryngoscope, mainland, john, alfred hospital, moon landing -
Warrnambool and District Historical Society Inc.
Tools, Plane Tool, Late 19th century
... in the base of the body. The straight-edged metal blade and the wooden... of the body. The straight-edged metal blade and the wooden piece ...This plane tool is believed to have belonged to a Warrnambool carpenter, Henry Phillips. English-born Henry Phillips (1821-1896) came to Australia with his wife Elizabeth in 1849 and lived for some time in Port Fairy. In 1865 he formed a partnership in Warrnambool with Christopher Beattie and established the undertaking business of Beattie and Phillips. This business continued on after the deaths of the founding partners, Beattie and Phillips and lasted until the year 2000. In Warrnambool Henry Phillips was involved in the management of the Mechanics’ Institute.This tool is of interest, firstly as an example of a 19th century carpenter’s tool and secondly as a memento of the 19th century Warrnambool businessman, Henry Phillips. This is a wooden plane tool with a boat-shaped body curved at the sides and a wooden piece inserted in a top opening. This wooden piece holds a metal blade which protrudes at a slit opening in the base of the body. The straight-edged metal blade and the wooden piece are held together by a metal screw. vintage tools, henry phillips -
Warrnambool and District Historical Society Inc.
Tool - Wood Saw, H. Disston & Sins, Late 19th century
... with a serrated edge on the straight side of the blade The handle... blade with a serrated edge on the straight side of the blade ...This saw could have been used in industry or in a home situation. It was made by the H. Disston & Sons of U.S.A. This company was established in 1850 by Henry Disston and by the 20th century it was the largest maker of hand saws in the world. The hand saws used today differ little from this early model. This saw is retained as a good example of a hand tool that is over 100 years old. This hand saw has a triangular-shaped metal blade with a serrated edge on the straight side of the blade The handle is wooden with five metal screws. There is a metal plaque containing the name and emblem of the manufacturer. The saw is a little rusty and stained.‘H. Disston & Sons Philada’ ‘T.E.G.’ household tools, history of warrnambool, wood saw -
Warrnambool and District Historical Society Inc.
Tool - Carpenter's hand saw, H. Disston & Sons, Late 19th century
... with a serrated edge on the straight side. The blade has details...-shaped metal blade with a serrated edge on the straight side ...This saw was made by H. Disston and Sons, a Philadelphia, U.S.A. company founded in 1850 by Henry Disston. It became the largest saw maker in the world in the 20th century. This saw could have been used for industrial or for household purposes. The hand saw used today features the same basic pattern as this one. This saw has no known local provenance but is retained as an example of a hand saw that is over 100 years old. This saw has a triangular-shaped metal blade with a serrated edge on the straight side. The blade has details of the manufacturer imprinted into the metal but this is mostly indecipherable. The wooden handle has four wooden screws and a fern pattern etched into one side. It also has a metal plaque with the name and emblem of the maker. The saw has some staining.‘H. Disston & Sons Philada’household tools, history of warrnambool, wood saw -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Tools, metal scythe, c1880
... straight, the blade parallel to the ground and very close... by holding the handle , with the arms straight, the blade parallel ...A scythe is an agricultural hand tool for mowing grass or reaping crops. It was largely replaced by horse-drawn and then tractor machinery. A scythe consists of a wooden shaft and a long, curved blade is mounted at the lower end, perpendicular. Scythes always have the blade projecting from the left side when in use. Mowing is done by holding the handle , with the arms straight, the blade parallel to the ground and very close to it, and the body twisted to the right. The body is then twisted steadily to the left, moving the scythe blade along its length in a long arc from right to left, ending in front of the mower, thus depositing the cut grass to the left. Mowing proceeds with a steady rhythm, stopping at frequent intervals to sharpen the blade. The correct technique has a slicing action on the grass, cutting a narrow strip with each stroke Mowing grass is easier when it is damp, and so hay-making traditionally began at dawn and often stopped early, the heat of the day being spent raking and carting the hay cut on previous daysEarly settlers and market gardeners used these scythes as they established their farms in Moorabbin Shire c1880A large metal scythe with a wooden handle x 2early settlers, pioneers, market gardeners, moorabbin, bentleigh, brighton, cheltenham, tools, blacksmiths -
Royal Australian and New Zealand College of Obstetricians & Gynaecologists (RANZCOG)
Artery forceps used by Dr Lorna Lloyd-Green
... Two pairs of stainless steel straight artery forceps... pairs of stainless steel straight artery forceps. Forcep blades ...These forceps belonged to Dr Lorna Lloyd-Green.Two pairs of stainless steel straight artery forceps. Forcep blades are secured with a screw attachment. One pair of forceps (.1) is inscribed with the number '3' inside both forcep shafts. The second pair (.2) is inscribed with the number '2' inside both forcep shafts.'3' '2'surgery -
Warrnambool and District Historical Society Inc.
Small Chisel, Late 19th century
... of the handle to form a chiselling straight edge. The metal blade... indented in the middle to give a firmer grasp and a metal blade ...This chisel is one of several tools that are believed to have belonged to the Warrnambool carpenter and businessman, Henry Phillips. English-born Henry Phillips (1821-1896) came to Australia with his wife Elizabeth in 1849. They lived for some years in Port Fairy. In 1865 Henry formed a partnership with Christopher Beattie to establish the Warrnambool undertaking business of Beattie and Phillips. This business continued on after the deaths of the founders and lasted until the year 2000. In Warrnambool Henry Phillips was involved in the management of the Mechanics Institute. This tool has a wooden handle indented in the middle to give a firmer grasp and a metal blade inserted at the end of the handle to form a chiselling straight edge. The metal blade is held at the handle end by a band of metal. The wood in the handle has been gouged out and broken at the top end on both sides. Traces of paint are on the handle and the blade is rusted.vintage tools, henry phillips, warrnambool, history of warrnambool -
Warrnambool RSL Sub Branch
Cut Throat or Straight Razor, Max Voos, Germany, 1930's-1940's
... cutthroat/straight razor with steel blade. Two handle pieces known... side no inscriptions. Blade: Side 1- FLIC enclosed ...Curved Acrylic (probably) or tortortoise shell handled cutthroat/straight razor with steel blade. Two handle pieces known as 'scales'. Blade hinged through handle with rivet at one end. Thumb notch as part of blade continues past hinge. Two more rivets attach two pieces of handle together; 1st rivet with spacer 4cm from hinge rivet, 2nd rivet at opposite end to hinge. Handle:Gold decorative writing-Flic R with 'REGD' enclosed below on one side approx 9 cm from hinge. 2nd side no inscriptions. Blade: Side 1- FLIC enclosed in rectangular parrallelagram next to hinge. Etched 'gold' decoration and inscription along back edge. Inscription reads 'FLIC GOLD'. Blade: Side 2- Near Hinge- MADE IN GERMANY FROM BEST FLIC SILVER STEEL. Blade: Back edge- Serrations for 5cm from hinge. -
The 5th/6th Battalion Royal Victoria Regiment Historical Collection
Weapon - 303 Bayonet, Pattern 1907 bayonet without hooked quillon
... its push button locking bolt The polished blade is straight... by Australian forces in the first and second world wars 5/6 RVR blade ...Bayonet type used by Australian forces in the first and second world warsBritish Pattern 07 bayonet and scabbard. The hilt has a straight crossguard with a muzzle ring and the grips are plain wood held to the tang with two screw bolts. The pommel is missing its push button locking bolt The polished blade is straight having a single fuller to each side and the riccasso is stamped with MA 1907 over 1. '. The brown leather scabbard has a blued steel chape and tear drop locket. The locket throat edge is stamped 3MD35564. The leather body is marked on the reverse MANGROVITE '44.blade -1907 1 Scabbard -MANGROVITE '44.5/6 rvr -
Upper Yarra Museum
Razor, Cut throat
... the blade angle. Straight razors cover a much greater area per... the blade angle. Straight razors cover a much greater area per ...Sharped Edged instrument used for cleaning hair from the skin. http://en.wikipedia.org/wiki/Straight_razor A straight razor is a razor with a blade that can fold into its handle.[1] They are also called open razors and cut-throat razors. HISTORY The first modern straight razor complete with decorated handles and hollow ground blades was constructed in Sheffield, England, by Benjamin Huntsman in 1740. Huntsman's process was adopted by the French sometime later. The English manufacturers were even more reluctant than the French to adopt the process and only did so after they saw its success in France.[5] Straight razors were the most common form of shaving before the 20th century and remained that common in many countries until the 1950s. TODAY Straight razors are still manufactured. DOVO, of Solingen, Germany, and Thiers Issard of France are two of the most well-known European manufacturers. Feather Safety Razor Co. Ltd. of Osaka, Japan makes a razor with the same form as a traditional straight, but featuring a disposable blade that can be installed through an injector-type system. Modern straight razor users are known to favor them for a variety of reasons. Some are attracted to the nostalgia of using old and traditional methods of shaving. It is a masculine ritual comparable to pipe smoking. Others profess an interest in reducing the waste of disposable blades.[11][22] Still others agree that straight razors provide a superior shave through a larger blade and greater control of the blade including the blade angle. Straight razors cover a much greater area per shaving stroke because their cutting edge is much longer than any of the multiblade razors. Ivory cut throat razor, with cream case 00121.3.Known as a straight razor.Razor with square point, full hollow ground 5/8” blade and double transverse stabiliser. The centre pin adds stability and rigidity to the handle---I think this is it ROM Parts The narrow end of the blade pivots on a pin, between 2 pieces of ivory forms the handle. LONG EXTRACT FROM WIKI _ SHORTEN to describe 00121 The parts of a straight razor and their function are described as follows: The narrow end of the blade rotates on a pin called the pivot, between two protective pieces called the scales or handle. The upward curved metal end of the narrow part of the blade beyond the pivot is called the tang and acts as a lever to help raise the blade from the handle. One or two fingers resting on the tang also help stabilize the blade while shaving. The narrow support piece between the tang and the main blade is called the shank, but this reference is often avoided because it can be confusing. The shank sometimes features decorations and the stamp of the country of origin. The top side and the underside of the shank can sometimes exhibit indentations known as fluting, or jimps for a more secure grip.[8] The curved lower part of the main blade from the shank to the cutting edge is called the shoulder.[9] The point where the shoulder joins the cutting edge is called the heel. A thick strip of metal running transversely at the junction where the main blade attaches to the shank is called the stabiliser. The stabiliser can be double,[10] single or can be absent in some razor models. The first stabiliser is usually very narrow and thicker and runs at the shank to blade junction, covering the shank and just spilling over to the shoulder. The second stabiliser can be distinguished since it is considerably wider and narrower, appearing after the first stabiliser and running lower into the shoulder. The non-cutting top of the blade is called the back or the spine while the cutting part of the blade opposite the back is called the cutting edge.[11] Finally the other free end of the blade, at the opposite end of the tang, is called the point and, sometimes, the head or the nose.[9][12] There are two to three pins in any handle. The middle pin, if present, is plastic coated and is called the plug.[13] Its function is to stabilise the sides of the handle so that they cannot be squeezed in the middle. When folded into the scales, the blade is protected from accidental damage, and the user is protected from accidental injury. During folding, the back of the blade, being thick and normally with a curved cross-section, acts as a natural stopper and prevents further rotation of the blade out of the handle from the other side shaving, lever, handle, blade, pivot, razor, tang -
Flagstaff Hill Maritime Museum and Village
Domestic object - Razor Strop, Early 19th century
... to maintain a shaving edge on a thin blade such as a straight razor... sharpens straight razors and safety blades and removes old razor ...A razor strop is flexible strip of leather or canvas used to maintain a shaving edge on a thin blade such as a straight razor. Fine powdered jeweler's rouge or other pastes can be added as an abrasive to polish the blade. The strop may be a hanging strip or a hand-held paddle. This one is a hanging strop. Strops were quite commonly found in barber shops and homes before the invention of the safety razor, They are still used for sharpening tool blades. The person using the strop would draw the spine of the blade down along the strop with the blade following, without putting any pressure on the blade. At the end of the stroke, rotate the blade over its spine then draw the spine along the strop again so that the edge moves away from the top. The finer grade of leather strap is used to give the final finish. KEEN EDGE MANUFACTURER In March 1906 Popular Mechanics magazine included an advertisement for Keen Edge Strop. The promise given by the advertiser, Eddy Mfg. Co. (206 Broadway, New York) was “Use the Keen Edge strop for 90 days and if not satisfied return to us and we will refund your money“. The advertisement was for a Combination Razor Strop, “the only strop made which requires no dressing.” Readers were invited to send for a booklet on Razor and the Face. In 1924 Popular Mechanics, published by Hearst Magazines, displayed an advertisement seeking a sales manager “… to sell [to] drug, hardware and cigar stores Keen Edge Strop Dressing, which sharpens straight razors and safety blades and removes old razor strops.” At that time the Keen Edge Mfg. Company was in Dallas, Texas. Razor strops are of historical significance, representing personal effects of men from the time period when men relied on strops to keep a sharp edge on their shaving blade. Strops were commonly owned and used until the acceptance of safety razors.Razor strop, leather and metal. Keen Edge brand, double straps: two straps of different grade leather joined at ends with metal fittings. Stropping faces; sharpening surface is stained red and finishing surface is stained black. One end has padded, bulbous shaped leather handle, the other end has metal, swivel hook hanger. Inscriptions pressed into leather at the ends of the straps. Impressed into leather "FINEST SELECTED HIDE", "KEEN EDGE", "FINISH" (black stained side), “A SHARPENER" (red stained side), “1 2 3”warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, great ocean road, shaving leather, shaving accessory, barber’s equipment, barber shop razor strop, razor strop, straight razor, razor and knife sharpener, keen edge razor strop -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Tools, Coping saw, c1900
... ensures that the thin blade is straight and not twisted along its... ensures that the thin blade is straight and not twisted along its ...A coping saw is a type of hand saw used to cut intricate external shapes and interior cutouts in woodworking or carpentry. It is widely used to cut mouldings to create coped rather than miter joints. It is occasionally used to create fretwork though it is not able to match a fretsaw in intricacy of cut, particularly in thin materials. Coping saw blades are always thicker and much coarser cutting than typical fretsaw blades. A coping saw consists of a thin, hardened steel blade, stretched between the ends of a square, c-shaped, springy-iron frame to which a handle is attached. The blade is easily removed from the frame so that the blade can be passed through a drilled hole in the middle of a piece of wood. The frame is then re-attached to the blade and the cut starts from the middle of the piece. Long cuts perpendicular to the edge of the material are possible but the shallow depth of the frame rather limits how far from the edge one may cut. The much deeper frame of the fretsaw is more useful for cutting well away from the edge but conversely cannot manage the thicker materials commonly cut by the coping saws. The coping saw blade is installed with the teeth pointing towards the handle. Unlike a hacksaw, which has the teeth pointed away from the handle, the coping saw cuts on the pull stroke. The coping saw blade is removable by partially unscrewing the handle. The blade is prevented from rotating by means of the short, steady bar provided where the blade is attached. Loosening the handle also allows the blade to be rotated relative to the frame as desired. Carefully aligning the finger steady bars at the top and bottom of the blade ensures that the thin blade is straight and not twisted along its length. Re-tightening the handle tensions the blade and locks it at the desired angle relative to the frame. The short steady bar nearest the handle is held securely between finger and thumb while the handle is tightened to ensure the blade remains at the desired angle. Unlike the fretsaw the coping saw blade has holding pins which lock securely into the angled slots of the rotatable blade holders. Gentle curves are achieved by slowly turning the whole frame by means of the handle while continuing to cut steadily. A coping saw with wooden handle but no bladetools, saws, steel , clamps, metalwork, woodwork, carpentry, early settlers, pioneers, market gardeners, moorabbin, bentleigh, cheltenham, fretsaw, coping saw, bowsaw, blacksmiths, -
Orbost & District Historical Society
leather strop, Early 20th century
... to maintain a shaving edge on a thin blade such as a straight razor... to maintain a shaving edge on a thin blade such as a straight razor ...A razor strop is flexible strip of leather or canvas used to maintain a shaving edge on a thin blade such as a straight razor. Fine powdered jeweler's rouge or other pastes can be added as an abrasive to polish the blade. The strop may be a hanging strip or a hand-held paddle. This one is a hanging strop. Strops were quite commonly found in barber shops and homes before the invention of the safety razor, They are still used for sharpening tool blades.This item is an example of the self-reliance shown by rural families when household necessities were not readily available.A flexible double-layered horse hide leather strop. One strip has a slightly coarser texture. This is a hanging strop which has a metal swivel on top so that the strop can be turned over while hanging from a hook/peg.On hand grip The Keen Edge Strop, genuine horse hide All Black Stropper No. 2strop razor-strop shaving personal-effects -
Orbost & District Historical Society
razor, Durham Duplex Razor Company, Early 20th century
This a cheaper version of The Durham razors. The Durham Safety Razor Co. was founded in New York,N.Y.c1908 by Thomas C. Durham. The first Durham Duplex U.S. Patent was filed in October 1906 and then in January and March 1907. By 1920 Durham-Duplex claimed eight million users. after many mergers a successor company Durham Duplex in Sheffield England still operates selling blades and knives with retractable blades.The Durham Demonstrator was a popularly used safety razor and hair trimmer of the first half of the 20th century before the use of electric razors.A Durham Demonstrator. This is a hair thinning and trimming resembling a straight razor which folds back into the handle. The handle is black plastic/ composite. It still contains the blade which is double edged. it has a built-in open comb safety guard.On handle: "To Be Used With/ Durham-Duplex Blades" on one side and "Durham Demonstrator" on the other. The blade is marked "Pat'd U.S.A. May, 28 07"razor durham-demonstrator grooming hair-trimmer -
Orbost & District Historical Society
razor, Thomas R. cadman & Sons Ltd, Early -first half 20th century
... , which incorporates a disposable blade. Straight razors were once ...Straight razors were once the principal method of manual shaving but have been largely overshadowed by the safety razor, which incorporates a disposable blade.Straight razors were once the main method of shaving, This razor with the BENGALL mark was known for its quality on an international scale. During WW11 Cadmans supplied the defence forces with 250,999 razorsCut Throat Razor by 'T R Cadman & Sons Sheffield England'. It has a metal blade, a cream coloured bakelite handle, with a pin hinge for folding to cover blade.Bengall R. Cadman & Sons Sheffield Englandrazor grooming cut-throat-razor -
Orbost & District Historical Society
razor, Early 1900's
Straight razors were once the principal method of manual shaving, they have been largely overshadowed by the safety razor and electric razors.A straight razor with an ivory coloured bakelite handle. the blade folds back into the handle'RELIANCE - WALDOO ERN 1683 Made in Germanygrooming ern-carl razors-straight -
Orbost & District Historical Society
cross cut saw, first half 20th century
... into a steel socket at each end. The blade has one straight edge.... The blade has one straight edge and a toothed curved edge. cross cut ...Crosscut saws are used to cut down trees and to saw the trunks to length. This is a two man cross cut saw. The two-man crosscut saw has wooden handles that fit into a steel socket at each end. The teeth are designed to enable both users to have equal strength.Orbost has historically been based on the timber industry and it remains an important but diminishing economic activity. Timber cutting tools are reminders of this history.A steel bladed cross cut saw with wooden handles that fit into a steel socket at each end. The blade has one straight edge and a toothed curved edge. saw timber cross-cut-saw tool -
Flagstaff Hill Maritime Museum and Village
Tool - Bow Saw, Prior to 1950
A coopers turning or bow saw is a woodworking tool used for straight or curved cuts. A bow saw is a type of frame saw with a thin toothed blade that is held in tension by a frame with two long narrow handles called "cheeks" that are supported and separated by a thin stretcher in the center of the handles, making a wide H shape (the cheeks form the uprights of the H, the stretcher the crossbar of the H). The blade is kept in tension with a turnbuckle that runs parallel to the blade between the two cheeks but on the opposite side of the stretcher.An age old tool used for cutting timber for hundreds of years before the modern cross cut saws were invented. This design of saw was part of a Coopers tool kit and used in the production of making barrels. However this item at this time cannot be associated with an historical event, person or place, provenance is unknown, item assessed as a collection asset as it is believed to have been produced before 1950.Bow saw wooden handle with metal blade missingNonewarrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, bow saw, turning saw, coopers tools, cutting wood, sawing timber, coopering -
Kiewa Valley Historical Society
Straight Myringotome Knife
This medical / hospital instrument was used in the Tawonga District General Hospital which was built in the 1950s specifically for the increase in population due to the Kiewa Hydro Scheme.Historically Significant: Shows the development of scientific hospital equipment. Provenance: Used in the Tawonga District General Hospital which was remote and therefore required good equipment. Good condition and good interpretation capacity.Steel instrument - handle wide with gentle curve. Blade short, thin, flat and sharp with some rust.H.A.T.MELB. on handle Some rust on blade.medical equipment. hospital equipment. tawonga. mt beauty. hospital. medical. knife. nurse. doctor. -
Kiewa Valley Historical Society
Packing Forceps - straight
This medical / hospital instrument was used in the Tawonga District General Hospital which was built in the 1950s specifically for the increase in population due to the Kiewa Hydro Scheme.Historical: Shows the development of scientific hospital equipment. Provenance: used in the Tawonga District General Hospital which was remote and therefore required good equipment. Good condition and good interpretation capacity.Long steel scissors. Blades are bowed when closed with serrated ends for gripping. Used with packing gauze into a cavity.medical equipment. hospital equipment. scissors, forceps. mt beauty. tawonga. -
Kiewa Valley Historical Society
Skin Graft Knife
This medical / hospital equipment was used in the Tawonga District General Hospital which was built in the 1950s specifically for the increase in population due to the Kiewa Hydro Scheme.Historical: Shows the development of scientific hospital equipment. Provenance: Used in the Tawonga District General Hospital which was remote and therefore required good equipment.In yellow cardboard box with black writing. Hollow (loop) handle. Pivot is a screw so that the blade can be taken out. Blade has a hole for the screw. Has a shorter straight side and a longer side with teeth like a saw. It fits in a cavity shaped for the knife. Another cavity is next to it but is empty.Box: Eschmann Skin Graft Knife / Including ten sterile disposable blades. Followed by 3 other languages. Made in England hospital equipment. medical instrument. tawonga. mt beauty. knife. skin graft -
Kiewa Valley Historical Society
Tin Snips - Tool
Used by builders and plumbers to cut tin.Used by Alan Tyers who worked for the State Electricity Commission of Victoria on the Kiewa Hydro Scheme.Cousin's Regular Pattern. Used by builders and plumbers to cut tin. Regular pattern with straight cutting edge. Best cast steel, black finish, ground blades. 9 inch. When closed blades meet at the point. Handles meet when closed and are curved outwards."J. Cousins & Sons. Sheffield"- Inscribed on handle side of pivot on one side.tinsmith, tin snips, tool, secv, cousin's & sons -
Warrnambool and District Historical Society Inc.
Hacksaw & blade, Early 20th century
... with a metal blade on the straight side affixed with screws. The blade... shape with a metal blade on the straight side affixed ...This hack saw would have been used to cut metal. The blades were interchangeable according to the requirements of the job. The item could have been used on a farm or in industry. This item is retained as a good example of a tool commonly used in past times.This is a hack saw. It has a metal frame in a D shape with a metal blade on the straight side affixed with screws. The blade is finely serrated. Attached to the metal frame is a wooden handle. This hack saw also has an extra blade attached to the fixed blade with a piece of wire flex. The metal is somewhat rusty and the wooden handle is worn. vintage hand tools -
Warrnambool and District Historical Society Inc.
Wood Plane Tool, Late 19th century
... and has a centre piece gouged out and a metal blade protected... blade has a straight edge. A wooden handle at the end ...This tool is one of several in a collection that is believed to have belonged to the Warrnambool carpenter and businessman, Henry Phillips. English-born Henry Phillips (1821-1896) came to Australia with his wife Elizabeth in 1849. They lived for some years in Port Fairy and in 1865 Henry formed a partnership with Christopher Beattie to establish the Warrnambool undertaking business of Beattie and Phillips. This business continued on after the deaths of the founders and lasted until the year 2000. In Warrnambool Henry Phillips was involved in the management of the Mechanics Institute.This item is retained as an example of a vintage tool and as a memento of the Warrnambool carpenter and businessman, Henry Phillips.This is a large wood plane tool. It is rectangular in shape and has a centre piece gouged out and a metal blade protected by a wooden piece inserted into the top hole and protruding at the base of the body to form a planing tool. The metal blade has a straight edge. A wooden handle at the end of the tool body has been broken off but is retained with the tool. vintage tools, henry phillips, warrnambool, history of warrnambool -
Warrnambool and District Historical Society Inc.
Small Straight Plane, Late 19th century
This item is one of several tools that are believed to have belonged to the Warrnambool carpenter and businessman, Henry Phillips. English-born Henry Phillips (1821-1896) came to Australia with his wife Elizabeth in 1849. They lived in Port Fairy for some years. In 1865 Henry formed a partnership with Christopher Beattie and established the Warrnambool undertaking business of Beattie and Phillips. This business continued on after the deaths of the founders and lasted until the year 2000. In Warrnambool Henry Phillips was involved in the management of the Mechanics Institute. This item is of interest as an example of a vintage tool and as a memento of the Warrnambool carpenter and businessman, Henry Phillips.This is a piece of wood shaped to make two handles at the ends and a middle piece that has a metal blade inserted at the top. The metal blade has two projecting ends that fit through the middle wooden piece. When held upside down this item is used as a planing tool. vintage tools, henry phillips -
Lara RSL Sub Branch
Japanese Cavalry Sword, Japanese Model 1899 Cavalry Sword
Japanese Model 1899 Cavalry SwordJapanese Model 1899 Cavalry Sword This Japanese Model 1899 Cavalry Sword has a interesting hilt in that the grip is of wood with a metal backstrap. The wood is probably is very hard, and has been nicely checkered. The checkering continues right through on to the metal backstrap, giving a very interesting effect. The pommel is smooth and round, with a spanner type flush mounted nut which most likely acts to retain the tang. There is also a screw and spanner that is retaining the grip. The pommel is smooth and round, with a spanner type flush mounted nut which most likely acts to retain the tang. This Japanese Model 1899 Cavalry Sword has a interesting hilt in that the grip is of wood with a metal backstrap. The wood is probably is very hard, and has been nicely checkered. The pommel is smooth and round, with a spanner type flush mounted nut which most likely acts to retain the tang. The scabbard is a heavy duty steel example which exactly matches the steel used to construct the hilt. The scabbard is perfectly straight throughout, with a single carrying band and ring.A number is stamped near the hilt on the shoulder of the blade " 96982"japanese model 1899 cavalry sword, metal scabbard