A Fid is a conical tapered wooden tool used for separating the strands of rope for splicing. They were a tool traditionally made of wood or bone used to work with rope and canvas in marlinespike seamanship. A Fid differs from a marlinspike in material and purposes. A marlinspike is used in working with wire rope, natural and synthetic lines also may be used to open shackles, and is made of metal. A Fid is used to hold open knots and holes in the canvas, and to separate the "lays" (or strands) of synthetic or natural rope for splicing. A variation of the Fid, the grip fid, is used for ply-split braiding. The grip fid has a jamming cleat to pull a cord back through the cord split by the fid's point. Modern Fids are typically made of aluminium, steel, or plastic. In addition to holding rope open to assist the creation of a rope splice, modern push fid's have markings for precise measurements in a variety of sizes of rope. The length of these fid’s is typically 21 or 22 times the diameter of rope to be spliced. Fids have been used since sailing vessels were first used to travel the worlds seas the tool was invented to be used to splice rope and with working with canvas sails. A Fid is a sailors tool that has maintained its general design for hundreds of years and gives a snapshot into what the working life was like for sailors on board sailing ships for hundreds of years. The tool in its original design is still in regular use today by recreational sailors all over the world to splice and join lengths of rope.Metal Fid painted brown, flattened point turned end and hole for a lanyardNoneflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, marlinspike

This timber fragment is from the shipwreck of the SCHOMBERG (1855). The bow of the ship broke off after an unsuccessful salvage attempt to tow her off the Peterborough reef. At the wreck-site the submerged hull points north towards the beach but the front section is missing. Parts of the bow have been carried away by the eastward bearing ocean currents and have come ashore on the western coast of New Zealand’s South Island. Don Charlwood writes in Wrecks & Reputations (1977) that in 1871 “a piece of wreckage over 20 feet long and 12 feet wide was brought out” by land from its remote location at Tauperika Creek. In 1875 “an even larger section was brought out by sea”. It was suggested at the time that these relics of a large wooden sailing ship were from the wreck of the SCHOMBERG some 20 years earlier on the Victorian coast. “To corroborate the theory”, Charlwood continues, “a piece was sent to Halls of Aberdeen [the ship’s builders in Scotland]. They identified it as having come from the ship they had launched with such pride in 1852.” Charlwood, whose great-grandparents were passengers on the SCHOMBERG’s fateful maiden voyage, acquired some samples of the wreckage timber recovered in New Zealand, and brought them back with him to Australia. In 1976 “comparison was made of timbers from the New Zealand find and timber from the remains of the hull at Peterborough. They proved to be from the same ship.” The extraordinary journey of these pieces of wood from the once mighty clipper ship SCHOMBERG came to an end in 1984, when they were given to Flagstaff Hill by the author, and reunited with other shipwreck timbers and copper bolts from the vessel that are on display at the Maritime Village. The shipwreck of the SCHOMBERG is of State significance - Victorian Heritage Register S612A small piece of wood broken from the timbers of the shipwrecked clipper SCHOMBERG (1855, Peterborough) and retrieved from the southwest coast of New Zealand’s South Island. The artefact bears a reddish stain on exposed parts but the main surface is grey coloured. It appears to have been split off other wood fragments in the Flagstaff Hill collection (6257, 6259). It presents as a lighter less dense wood than oak, but may have lost mass through submersion.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, schomberg, shipwreck timber, don charlwood, ‘wrecks & reputations’

This timber fragment is from the shipwreck of the SCHOMBERG (1855). The bow of the ship broke off after an unsuccessful salvage attempt to tow her off the Peterborough reef. At the wreck-site the submerged hull points north towards the beach but the front section is missing. Parts of the bow have been carried away by the eastward bearing ocean currents and have come ashore on the western coast of New Zealand’s South Island. Don Charlwood writes in Wrecks & Reputations (1977) that in 1871 “a piece of wreckage over 20 feet long and 12 feet wide was brought out” by land from its remote location at Tauperika Creek. In 1875 “an even larger section was brought out by sea”. It was suggested at the time that these relics of a large wooden sailing ship were from the wreck of the SCHOMBERG some 20 years earlier on the Victorian coast. “To corroborate the theory”, Charlwood continues, “a piece was sent to Halls of Aberdeen [the ship’s builders in Scotland]. They identified it as having come from the ship they had launched with such pride in 1852.” Charlwood, whose great-grandparents were passengers on the SCHOMBERG’s fateful maiden voyage, acquired some samples of the wreckage timber recovered in New Zealand, and brought them back with him to Australia. In 1976 “comparison was made of timbers from the New Zealand find and timber from the remains of the hull at Peterborough. They proved to be from the same ship.” The extraordinary journey of these pieces of wood from the once mighty clipper ship SCHOMBERG came to an end in 1984, when they were given to Flagstaff Hill by the author, and reunited with other shipwreck timbers and copper bolts from the vessel that are on display at the Maritime Village. The shipwreck of the SCHOMBERG is of State significance - Victorian Heritage Register S612A piece of wood broken from the timbers of the shipwrecked SCHOMBERG (1855, Peterborough) and retrieved from the southwest coast of New Zealand’s South Island. The artefact is a light grey colour with plain long grain and bears a reddish stain on parts. Part of a drilled hole is red stained with traces of corroded metal still evident. The piece appears to have split off from other fragments that are in the Flagstaff Hill collection (6257, 6258) and it is in fragile condition.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, schomberg, shipwreck timber, don charlwood, ‘wrecks & reputations’

Wooden ammunition box with rope and timber carry handles. 2 u shaped metal closing clips secured by a split pin. The wood lid is hinged with 2 webbing strips. The inside has yellow felt padding and provision for wood dividers (missing)upper side of box has "S8" embossed. No other markingsbox, australian, military, army, ammunition, 1958

The original small, pioneer cottage was built in the late 1840s to early1850s, by an unknown pioneer. It was located on part of a 30 Acre allotment that was originally part of Henry Dendy’s 'Special Survey Brighton' granted in 1841 (5120acres). There is a small display of external cladding shingles from the original pioneer cottage. Wooden shingles were usually thin (3⁄8 to 3⁄4 in or 10 to 19 mm), relatively narrow (3 to 8 in or 76 to 203 mm), of varying length (14 to 36 in or 360 to 910 mm), and almost always planed smooth. The traditional method for making wooden shingles was to rive - hand split - them from straight-grained knot-free sections of logs pre-cut to the desired length known as bolts. These bolts were quartered or split into wedges. A mallet and axe were used to split out thin pieces of wood. The wood species varied according to available local woods, but only the more durable inner section of the log was usually used. The softer sapwood generally was not used because it deteriorated quickly. Because hand-split shingles were somewhat irregular along the split surface, it was necessary to dress or plane the shingles to make them fit evenly on the roof. This reworking was necessary to provide a tight-fitting roof over typically open shingle lath or sheathing boards. These are the original shingles found on Box Cottage by L Lewis 1970 and used in the reconstruction in 19843 x wood Shingles used on roof of Box Cottage c 1850box cottage museum ormond, henry dendy special survey brighton 1841, brighton, moorabbin shire, parish of moorabbin, county of bourke,cottages, pioneers, ormond, colonial, mckinnon, dendy henry, box william, box elizabeth, reitman william, convicts, lewis timber co. ltd., deam h, museums, box alonzo, smith a,

A Fid is a conical tapered wooden tool used for separating the strands of rope for splicing. They were a tool traditionally made of wood or bone used to work with rope and canvas in marlinespike seamanship. A Fid differs from a marlinspike in material and purposes. A marlinspike is used in working with wire rope, natural and synthetic lines also may be used to open shackles, and is made of metal. A Fid is used to hold open knots and holes in the canvas, and to separate the "lays" (or strands) of synthetic or natural rope for splicing. A variation of the Fid, the grip fid, is used for ply-split braiding. The grip fid has a jamming cleat to pull a cord back through the cord split by the fid's point. Modern Fids are typically made of aluminium, steel, or plastic. In addition to holding rope open to assist the creation of a rope splice, modern push fid's have markings for precise measurements in a variety of sizes of rope. The length of these fid’s is typically 21 or 22 times the diameter of rope to be spliced. Fids have been used since sailing vessels were first used to travel the worlds seas the tool was invented to be used to splice rope and with working with canvas sails. A Fid is a sailors tool that has maintained its general design for hundreds of years and gives a snapshot into what the working life was like for sailors on board sailing ships for hundreds of years. The tool in its original design is still in regular use today by recreational sailors all over the world to splice and join lengths of rope.Metal Fid painted half green, flattened end with a lanyard holeNoneflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, marlinspike

Black powder splitting guns were commonly used to split large logs into more manageable pieces before the advent of excavators and front-end loaders in bush logging operations. A typical splitting gun used in Victorian forests was a piece of high-grade steel about 1-1/2 to 2 inches in diameter and about 16 inches long, and slightly tapered at one end. They had a ¾ inch hole drilled about 9 inches deep into the centre of the shaft with a small pilot hole drilled from the outside to load the fuse. The tube was carefully loaded with an amount of black gunpowder using a funnel and spoon. Experience being the guide on how much powder to use, which depended on log size, species and difficulty of splitting the wood. The hole was stopped with a piece of wadded paper and the gun positioned at the end of a length of the log to be split. The splitting gun was then belted into the log with a large wooden maul or even the back of an axe to a depth of about 3 to 4 inches. There were often markings as a guide. This also had the effect of tamping the black powder inside the gun. Preferably the gun was backed up by another large log to absorb the shock and avoid it flying off in the bush somewhere. I have seen guns where a length of string and coloured flag could be attached to help find them. A length of fuse was then inserted in the small hole and lit. Kaboom !!!! Needless to say, the splitting gun was a dangerous implement.Commonly used to split pulpwood but now rareBlack Powder Splitting GunFive marking rings used to guide how far the gun was in the logforest harvesting

Also known as a froe (or frow), shake axe or paling knife, this tool is used for cleaving wood by splitting it along the grain. The L-shaped tool is hammered on the top edge of its blade into the end of a piece of wood in the direction of the grain, then twisting the blade in the wood by rotating the haft (handle).Shingle knife or paling splitter Metal knife with short wooden handletimber tools

The geometric pattern mimic Ukrainian embroidery design,using straw marquetry technique (which is similar to that of wood marquetry). The wheat straw was soaked in different pigments to achieve the required shades,dried,split and ironed flat. Then cut into various sizes and shapes to create this pattern. The pieces where then glued onto a backing board.The backing board was then glued on the back of the photo album. This album was received as a birthday gift in early1960's.This form of straw art is very rarely seen today.Book is black.Back page is coloured straw design. photographsphoto, book, straw, ukrainian design, 1960, family dutka

Round tapered section of mild steel. Widest end has been split to edges. Used to drive steel and wood into their final position.trades, blacksmithing

Original postcard showing two men splitting wood in the forest at Mt Dandenong. They are using axes. Early 1900s.On front of postcard: Splitting in the State Forestwood chop, splitters, wood splitters, forest, mt dandenong, axes

Postcard with title RAIL SPLITTERS printed on the front showing three men and a boy at a large, sawn tree. They all have implements used for cutting and sawing. There is a long gun leaning on the front of the felled tree. The postcard was written by Fred Dorey and sent to his sister Mary.in 1905.POSTCARD MT. DANDENONG SERIES Handwritten in black ink on back: Miss M Dorey 35 Smith Street Fitzroy Mt Dandenong 22.10.05 Dear Mary Write & let us know if you know this photo. Mrs Grant is getting a big boarding house up and Mrs Keys is going put up a new house hoping you are well I remain Your truly Fred fred dorey, mary dorey, tree, rail splitters, wood chop

An late 18th century court tennis racquet, made from two pieces of interlocked wood, secured with two screws. One is the handle/throat, the other is the shoulders/head. The latter unfortunately had, at some point in the past, split at the crown, and whipping was applied to reinforce it. The gut stringing is three-way. The throat and lower shoulders have been hand painted, with both linear and floral designs. Across the thoat on the obverse is the monogram which reads 'BWB'. Materials: Wood, Lacquer, Metal, Gut, Paint, Stringtennis

A wooden racquet, with a split open throat. Inscription across the base of the head of obverse: "RANGER". Inscription across the base of the head of reverse: HARRY C. LEE & CO. Company logo 'LEE' is stamped upon orange leather butt cap. Manufacturing details feature on left side of stem. Materials: Wood, Glue, Lacquer, Ink, Leather, Metal, Gut, Stringtennis

A wooden racquet, with a split open throat. Inscription across the base of the head of obverse: "RANGER". Inscription across the base of the head of reverse: HARRY C. LEE & CO. Company logo 'LEE' is stamped upon orange leather butt cap. Manufacturing details feature on left side of stem. Materials: Wood, Glue, Lacquer, Ink, Leather, Metal, Gut, Stringtennis

A wooden racquet with a split open throat, and long handle. The base of the head on the obverse features decal inscription: PRESIDENT. The short stem on the reverse features a decal of a crowned garter with the inscription: E. KENT. Remnants of the inscription DUCO PERMANENT/HIGH POLISH FINISH, feature across left side of stem. Materials: Wood, Glue, Lacquer, Metal, Gut, Ink, Leather, Cloth, Stringtennis

A wooden racquet with a split open throat, and long handle. The base of the head on both sides features decal inscription: SPEEDWOOD. The short stem on the obverse features a decal of a crowned garter with the inscription: E. KENT. Company logo also features on red cloth butt cover, impressed in gold.The inscription DUCO PERMANENT/HIGH POLISH FINISH, feature across right side of stem. Patent information across left side of stem. Materials: Wood, Glue, Lacquer, Metal, Gut, Ink, Leather, Cloth, Stringtennis

A wooden racquet with a split open throat, and long handle. The base of the head on the obverse features decal inscription: WOVEN-WOOD. The short stem on the reverse features a decal of a crowned garter with the inscription: E. KENT. Patent information across left side of stem. A hand poked, then inlaid inscription across the handle on obverse: CED. Materials: Wood, Glue, Lacquer, Metal, Gut, Ink, Leather, Cloth, Stringtennis

A wooden racquet with a split, open throat. The base of the head on both sides features the decal inscription: MONARCH. The stem on the obverse features the decal logo, in gold, red and black, of a dog above a diamond device. Inscription within and below device: D & M/.../SPORTING GOODS/MADE IN/U.S.A. Logo also features on red butt cover, impressed in gold. Inscription along right side of stem: MADE BY THE DRAPER-MAYNARD COMPANY/PLYMOUTH, N.H. Materials: Wood, Glue, Lacquer, Metal, Ink, Gut, String, Leather, Clothtennis

A wooden racquet with an open throat, split by a steel threading shaft, with inscription: CRAVEN. PAT. The base of the head on both sides features the decal inscription: SHUR-TITE. The stem on the obverse features a decal logo, in gold, red and black, of a dog above a diamond device. Inscription within and below device: D & M/.../SPORTING GOODS/MADE IN/U.S.A. Logo also features on red butt cover, impressed in gold. Inscription along right side of stem: MADE BY THE DRAPER-MAYNARD COMPANY/PLYMOUTH, N.H. Materials: Wood, Glue, Lacquer, Metal, Ink, Gut, String, Leather, Clothtennis

Dark wood honour board with gold lettering attached to the wall in the foyer at the Brighton Town Hall. A roundel in timber relief at the top containing the City of Brighton crest and British Coat of Arms. Below that is a raised timber relief panel inscribed in gold lettering 'MAYORS OF THE MUNICIPALITY'. The list of names and dates of the mayors from 1859 to 1965 is split over 2 raised timber panels, in four columns and divided by the headings BOROUGH, TOWN and CITY. mayor, municpality, brighton, city of brighton, borough of brighton, town of brighton, honour board, crest, coat of arms, brighton town hall

A Chemold Roy Emerson tennis racquet, with open throat, ribbon whipping around shoulders, and leather handle grip with repetitive quatrefoil perorations. Chemold logo features across base of head. Model name features along split shaft of throat. Red, white and blue Chemold trademark features at base of shaft. Plain, white plastic butt cap. Materials: Wood, Nylon, Ink, Plastic, Leather, Glue, Lacquer, Metal, Ribbon, Painttennis

A Davis CL-500, fibreglass composite tennis racquet, with an open throat and large head. Racquet features plain leather handle grip. Davis logo features across base of head. Model name features along split shaft. TAD "Kings of the Court" trademark features on lower shaft on reverse. Davis coat-of-arms "Duce virtute comite fortuna" trademark features on lower shaft on obverse. TAD trademark features on rubber butt cap. Materials: Wood, Nylon, Ink, Glue, Lacquer, Metal, Leather, Adhesive tape, Rubber, Fibreglass, Painttennis

A Davis Topspin, fibreglass composite tennis racquet, with an open throat, diagonally strung head, and leather handle grip with X-formation perforations. Davis logo features across base of head. Model name features along split shaft. TAD "Kings of the Court" trademark features on lower shaft on reverse. Davis coat-of-arms "Duce virtute comite fortuna" trademark features on lower shaft on obverse. TAD trademark features on rubber butt cap. Materials: Wood, Nylon, Ink, Glue, Lacquer, Metal, Leather, Adhesive tape, Rubber, Fibreglasstennis

A Dunlop Speed throat tennis racquet, with open throat/split shaft, ribbon whipping around shoulders and lower shaft, and leather handle with X-formation perforations. Dunlop logo features across base of head. Model name features on lower shaft. 'D' trademark in arrowhead device also features on lower shaft and white plastic butt cap. Materials: Wood, Plastic, Ink, Leather, Glue, Lacquer, Metal, Adhesive tape, Enamel, Nylon, Ribbontennis

An unstrung Dunlop prototype, wood-fibreglass composite racquet with oversize head and open throat/split shaft. Only adhesive label, on lower shaft on obverse reads: 361 GRAMS/31.9 CMS. Handle grip is still sealed in plastic wrap-around. Materials: Wood, Plastic, Leather, Glue, Lacquer, Metal, Adhesive tape, Fibreglasstennis