Has a strong association with Dave Kellett, motorman and inspector in Ballarat; issued to crews in order check and cancel tickets.Brass cast, chrome plated, machined, device used to cancel or punch paper tickets when purchased. Placed a hole in the ticket. Spring loaded, consists of two main parts with a pin & spring. Chrome plated wearing off. - see sketch on original worksheet.Has letter "U" punched inside of handles near pin.trams, tramways, ticket punch, tickets, fares

Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, 52 and 53 and 4444 to 4448, , 4996 and 4497, 9037 and Reg item 934 and 988 for articles on the safeworking systems.Demonstrates aspects of Safeworking on the Ballarat Tramway system to c1936 when replaced by electric signals. Yields Information about the operation of Ballarat's trams and safeworking procedures.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "STURT ST. SOUTH ST. " stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg.trams, tramways, staff, safeworking, tramway staffs, sec, signals

Demonstrates aspects of Safeworking on the Ballarat Tramway system from 1960 to c1936 when replaced by electric signs. Yields Information about the operation of Ballarat's trams and safeworking procedures.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "VICTORIA PARK LOOP / CARLTON ST LOOP" stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg. The top line of words has a reddish paint inlay. Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, to 53, 2473 and 4444 to 4448 and Reg item 934 and 988 for articles on the safeworking systems.trams, tramways, staff, safeworking, tramway staffs, sec, signals

Demonstrates aspects of Safeworking on the Ballarat Tramway system from 1960 to c1936 when replaced by electric signs. Yields Information about the operation of Ballarat's trams and safeworking procedures.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "CAR SHED LOOP / MACARTHUR ST LOOP" stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg. The stamped area appears to have been polished compared to the others. Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, to 53, 2473 and 4444 to 4448, 4496 and Reg item 934 and 988 for articles on the safeworking systems.trams, tramways, staff, safeworking, tramway staffs, sec, signals

Demonstrates aspects of Safeworking on the Ballarat Tramway system from 1960 to c1936 when replaced by electric signs. Yields Information about the operation of Ballarat's trams and safeworking procedures.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "CARLTON ST HADDON ST LOOP " stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg. Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, to 53, 2473 and 4444 to 4448, 4996 and 4497 and Reg item 934 and 988 for articles on the safeworking systems.trams, tramways, staff, safeworking, tramway staffs, sec, signals

Demonstrates aspects of Safeworking on the Ballarat Tramway system from 1960 to c1936 when replaced by electric signs. Yields Information about the operation of Ballarat's trams and safeworking procedures.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "DARLING ST LOOP RUBICON ST LOOP " stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg. Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, to 53, 2473 and 4444 to 4448, , 4996 and 4497 and Reg item 934 and 988 for articles on the safeworking systems.Ballarat Tramways Section Staff Darling St Loop Rubicon St Looptrams, tramways, staff, safeworking, tramway staffs, sec, signals

Demonstrates aspects of Safeworking on the Ballarat Tramway system from 1960 to c1936 when replaced by electric signs. Yields Information about the operation of Ballarat's trams and safeworking procedures.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "URQUHART ST LOOP TO GREY ST LOOP " stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg. Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, to 53, 2473 and 4444 to 4448, , 4996 and 4497 and Reg item 934 and 988 for articles on the safeworking systems.trams, tramways, staff, safeworking, tramway staffs, sec, signals

Demonstrates aspects of Safeworking on the Ballarat Tramway system from 1960 to c1936 when replaced by electric signs. Yields Information about the operation of Ballarat's trams and safeworking procedures.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "PLEASANT ST TO CARLTON ST LOOP " stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg. Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, to 53, 2473 and 4444 to 4448, , 4996 and 4497 and Reg item 934 and 988 for articles on the safeworking systems.trams, tramways, staff, safeworking, tramway staffs, sec, signals

Demonstrates aspects of Safeworking on the Ballarat Tramway system from 1960 to c1936 when replaced by electric signs. Yields Information about the operation of Ballarat's trams and safeworking procedures. Demonstrates what can happen in use - has been run over by a tram - possibly being exchanged on the move or some other story.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "STURT ST RUBICON ST " stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg. The staff has been run over by a tram and had the last part of the object cut off. Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, to 53, 2473 and 4444 to 4448, , 4996 and 4497 and Reg item 934 and 988 for articles on the safeworking systems.Ballarat Tramways Section Staff Sturt St Rubicon Sttrams, tramways, staff, safeworking, tramway staffs, sec, signals

Demonstrates aspects of tramway operation, cancelling or showing that tickets had been inspected following sales to passengers by the conductor or motorman. Traditionally used by tramway operators to check or cancel tickets.Brass cast, was chrome plated, machined, device or ticket punch, used to cancel or punch paper tickets when purchased. Placed a round hole in the ticket. Spring loaded, consists of two main parts with a pin & spring in addition. . Chrome plate has been extensively worn off. There are no manufacturer markings or numbers on the punch. On the inside of one of the handles are two saw cuts that could have been used to identify the punch.trams, tramways, ticket punch, tickets, fares

Demonstrates tramway equipment used by conductors or One Man Operators to hold and dispense coins when handling fares.Manufactured coin dispenser from brass and steel plate for 3 coins, - 3d, 6d and 1/- (5c and 10c coins fit the relevant slots). Coin holder sections are made from brass, fitted with springs and then braised together as unit. Screwed with four screws onto a cut and folded section of steel. The folded sections of steel would have allowed it fit into a cash bag or holder. The number "40" has been stamped into the lower section of the steel section - see image 3. See Reg Item 7082 for another example.tram, trams, fares, cash handling, tickets

Oval shaped high domed metal meat cover with turned wooden knob & a hanging hook, handle secured with a brass screw with wing nut.domestic equipment, food storage & preservation, meat cover, k199

Black cast iron coffee grinder with pull out drawer for catching ground coffee, gold coloured funnel on top for beans and a handle with wooden knob for turning grinder, brass screw & name plate on front, square base with holes for securing, hand made lid possibly cut from motor oil can.T & C Clark & Co Ltd Wolver Hampton Druertons improved Clark & Co Manufacturersdomestic equipment, food preparation, kitchen, k182

The wreck site of the Earl of Charlemont is historically and archaeologically significant for the remains of its cargo and passengers' belongings from an international immigrant ship of the gold rush period, representing the cultural material being bought out to Australia in a typical immigrant ship. It is socially significant for the descendants of the many immigrants who made it ashore safely, and who have erected a memorial cairn to their forbears on Point Flinders.4 brass implements: fire poker, fire shovel handle, shaft and head of unknown implement, piece if fire tongs. 1 copper dumpship wrecks, earl of charlemont, fire implements

Black wooden mantle clock with pendulum bob, made in U.S.A. by the Sessions Clock Company, mounted on ornate metal feet with metal handles on each end, four faux marble columns in green with metal tops & bases. Round gold dial with black numerals and hands, brass bezel with flat glass. 8 day time and strike, chiming the hours on a gong and half hour on a bell. Original paper label on back with manufacturers details and operating instructions.The Sessions Clock Cohorology, clocks, mantle

Object. Black wooden mantle clock with pendulum bob made in U.S.A by the Sessions Clock Company, mounted on ornate metal feet, and decorated with four columns supporting Gothic arches, with torch like ornamentation between them and an ornate handle on each end. Round white enamel dial with black numerals & hands, a brass bezel with convex glass. 8 day running with gong strike on hour & half hour. Brass plaque on front reads presented to Mr.P.Cooper by his fellow employees of the Water Commission Bendigo on his retirement 30.6.1926.Sessions Made in U.S.Ahorology, clocks, mantle

Used by tramway revenue clerks, most likely the MMTB, including the Ballarat Tramway Museum to count coins, as only so many 3d or 6d would fit into each container. Each has a hole in the base to enable it to be checked that it was empty prior to use or after being used. One of the 3d containers have a loose "washer" which shows the nature of the construction. Has been secured with a piece of wrapping tape. One of the 6d tubes has a label advising that it would hold "$30 of $2 coins"Demonstrates the methodologies used to count coins and stack them in a revenue office. Provides a sample of each coin that would have been used. Brass coin holder - for use in counting 3d and 6d coins. Made from brass tube with a brass washer rolled or fixed to one end. In storage bag is are 2 x 3d and a 2 x 6d and 1x5c coins. 5 No. x 6d and 6 No. x 3d holders held in the collection.tramways, tickes, cash, cash handling, depots, coins, revenue clerks

An enamelled badge with a flapping bird above a circular target of white black blue and red concentric circles with a brass bow superimposed on it and enclosed by Kew City Bowmen with 2 crossed arrows below, on a violet blue background mounted on the handle of a butter knifeKew City Bowmen (front) Pitcher epns A1 (reverse)kew city bowmen

An enamelled badge with a flapping bird above a circular target of white black blue and red concentric circles with a brass bow superimposed on it and enclosed by Kew City Bowmen with two crossed arrows below, on a violet blue background mounted on the handle of a spoon Kew City Bowmen (front) Pitcher epns A1 (reverse)kew city bowmen, souvenirs - spoons

The original owner of the evening bag was Elizabeth (Betty) McGregor. The bag was a gift from her husband, Ian McGregor (Managing Director of Ingersoll Rand), during a trip to Europe. The bag was purchased in Burlington Arcade, London in 1955. An accompanying photograph shows Betty, in attendance at a Captain's cocktail party with the evening bag on her arm. Betty was the best friend of the my mother, and not having children of their own, Betty and Ian were very good to my sister and I. Betty gifted the bag to me in 1983. As a Kew resident, it gives me much pleasure to pass on this evening bag to the Fashion & Design collection of the Kew Historical Society. (Kate Reeve, 2022)Small brass evening bag, covered with black silk and rhinestones. The box is of a flattened cylindrical shape with a looped handle. The lid of the bag is hinged on one side and contains a mirror on its interior. Inside the evening bag is a small black silk purse attached to the bag with a brass chainNilfashion & design - 1950s, accessories, evening bags

The Kew Historical Society's Fashion & Design collection includes a small and representative collection of reticules, purses and handbags, purchased, inherited or collected by members of the Society. These items date from the Nineteenth and Twentieth centuries, and conform to fashions and styles popular during the period of their use. Some of the items are handmade, while others are mass-produced commercial products. The handbag was owned by, used and donated by Dione McIntyre.The McIntyre Collection of clothing and clothing accessories forms one of the largest single donations to our Fashion & Design collection. It includes clothing and clothing accessories worn by four women in the Cohen and McIntyre families across three generations. The items worn by Melbourne architect, and Kew resident, Dione McIntyre date from the 1960s and 1970s, and include evening wear, day wear, hats and shoes. As Dione McIntyre often accompanied her husband, fellow architect Peter McIntyre, to formal events, there are a number of pieces of evening wear among the items. The McIntyre Collection also includes items worn by women of an earlier generation: by Lilian Cohen, Dione McIntyre's mother, and by her mother-in-law, the wife of the architect Robert McIntyre. At the other end of the chronological spectrum are a number of outfits belonging to, worn and donated by Annie McIntyre. These include outfits created by notable late 20th century Australian and/or international fashion designers. The McIntyre Collection is significant historically and artistically as it includes examples of design that demonstrate changing tastes in fashion over an 80-year period. The collection is also significant in that it includes the work of a large number of Melbourne designers from the 1960s to the 1990s. Black Oroton handbag with brass and black enamel frame and handle. The inside label includes the company name - “OROTON” - and maker details - “Made in West Germany”.costume accessories, handbags, oroton, costume accessories, handbags, purses, oroton, mcintyre collection

The Kew Historical Society's Fashion & Design collection includes a small and representative collection of reticules, purses and handbags, purchased, inherited or collected by members of the Society. These items date from the Nineteenth and Twentieth centuries, and conform to fashions and styles popular during the period of their use. Some of the items are handmade, while others are mass-produced commercial products. The handbag was owned by Dione McIntyreThe McIntyre Collection of clothing and clothing accessories forms one of the largest single donations to our Fashion & Design collection. It includes clothing and clothing accessories worn by four women in the Cohen and McIntyre families across three generations. The items worn by Melbourne architect, and Kew resident, Dione McIntyre date from the 1960s and 1970s, and include evening wear, day wear, hats and shoes. As Dione McIntyre often accompanied her husband, fellow architect Peter McIntyre, to formal events, there are a number of pieces of evening wear among the items. The McIntyre Collection also includes items worn by women of an earlier generation: by Lilian Cohen, Dione McIntyre's mother, and by her mother-in-law, the wife of the architect Robert McIntyre. At the other end of the chronological spectrum are a number of outfits belonging to, worn and donated by Annie McIntyre. These include outfits created by notable late 20th century Australian and/or international fashion designers. The McIntyre Collection is significant historically and artistically as it includes examples of design that demonstrate changing tastes in fashion over an 80-year period. The collection is also significant in that it includes the work of a large number of Melbourne designers from the 1960s to the 1990s. White, Oroton style handbag with brass and white enamel frame and handle.handbags, costume accessories, oroton, mcintyre collection

Fibre (?) suitcase, green, with green lining. Two clasps with keyholes, and handle. Pockets on inside made of lining. Light-coloured stitching on outside.secure lever' marked on brass locks. On lid stays, 'A.E.L. Patent 8475'personal effects, travel goods, suitcase, travel, green fibre (?)

Condiments set including stand made of brass (?) with four ball feet, flat base, wire frame and handle to fit four glass containers. 1st glass container: rectangular glass box (no lid) with moulded geometric pattern. 2nd glass container: square base with round neck, same geometric pattern, broken stopper. 3rd glass container: square with metal hinged lid with knob.E.P.N.S., 1' (Electro-Plated Nickel Silver), embossed on frame and metal lid of 3rd itemdomestic items, food and drink consumption, condiments, glass, rack, e.p.n.s., metalwork

Vinyl imitation-crocodile skin light brown rectangular box, lined with cream satin. Brass clasp on front. Inside, one casine comb, half fine-tooth, half large-tooth. One hairbrush with casine handle and plastic bristles.No visible markingstoilet requisites, hairdressing, hair, brush, comb, casine, set

Nickel plated skim milk and cream separator. Splits into six pieces; some pieces are believed to be missing. Two pieces are cylindrical and have long spouts that curve downwards at the ends. Conical shaped piece which goes in centre and has hole through the middle (This piece has removable brass screw). Long straight rod with wooden handle and small, threaded section at other end. Rounded, circular rubber band, probably used as seal. Large round pot with thin flanged rim, seated on raised base edges. Tap with fitting on one side. Round piece with three evenly spaced legs. both sides slightly domed - fits into upper separator piece.On the brass nut of the conical shaped piece is engraved "unscrew" with an arrow adjacent. "10516-C" with another arrow and oval shaped trademark with lines inside. Embossed on the external casing of the conical piece is "2".food technology, dairying, milk, cream, dairy, separator, nickel, steel.

Pair of copper vases, with long cylindrical necks and wide, rounded bases. Two handles, made of brass, one on each side, follow shape of vase, made of flattened metal. Necks have decorative embossing with floral motifs. Rim also made of brass.No visible markingsdomestic items, ornaments, vase, flowers, decorative

Large rectangular trunk lined with green and cream material. On each side is a mesh dome which opens with a clasp (to protect certain items?) including top and bottom. Brass clasp with locking mechanism, who smaller latches on either side. Leather handle, leather re-enforcements on each corner, attached with tacks. Exterior made of flaxite fiberBrass plaque on left hand side, 'Warranted Flaxite fiber rec trade mark featherweight' with feather in the centre. Sticker saying 'luggage Melbourne (sp.-st.) Cootamundra (NSW) Victorian Railways' on right hand side.personal effects, travel goods, trunk, travel, lock, storage, flaxite, featherweight