CAst iron lace was made in foundries in most cities. There were 42 such foundries in Melbourne alone. It was cheaper to make than wrought iron. "Pig iron"' iron ore, was melted in a blast furnace, mixed with alloys and poured into moulds usually made with sand. The alloys needed a minimum of 2% carbon.Black and White photo by A Doney of Balustrade on property on the corner of Forest and Barnard Streets Bendigo.A Doney Bendigoalan doney, bendigo, wrought iron, forest street bendigo, barnard street bendigo

Iron leg shackles were worn by convicts to both punish inmates and prevent escape. Combined with physically exhausting labour, they helped control prisoners. The shackles weighed a considerable amount (there were differing sizes) which made it difficult to walk easily, resulting in a shuffling gait.A pair of very heavy leg irons. They are made of iron with holes at each side so they can be bolted around the legs. There is a long iron chain connecting the two D-shaped pieces.leg-irons shackles convicts

GALVANISED IRON TANK RIG ORR OAT BIN MIRAPHOTOGRAPH OF GALVANISED IRON OAT BIN WITH ONE MAN SITTING ON RIM OF TANK ANOTHER MAN STANDING ON WOODEN LADDER AGAINST THE TANK.photographs, weickhardt, tank, oat bin

Sad-irons or "solid" irons were made by blacksmiths and used to smooth out material by pressing the hot iron over it. A piece of sheet -iron was placed over the kitchen fire and the irons placed on it could be heated whilst remaining clean of ash.. The women used 2 irons - one heating while the other was used. Thick cloth or gloves protected their hands from the hot irons. The handle was removed from the cool iron and re- attached to remove the hot iron from the fire. The cool iron was replaced on the fire or stove to heat again. These irons were cleaned with steel wool to prevent them marking the material. If the iron was too hot the material would scorch. Most homes set aside one day for ironing and some large households had an ironing room with a special stove designed to heat irons. However, most women had to work with a heavy, hot iron close to the fireplace even in summer. Thomas Fletcher (1840-1903). By 1880s he had a gas appliance manufactory in Thynne Street, Warrington. By 1895 the company had become Fletcher Russell and Co Gas Engineers, his firm having merged with Alexander and William Russell of Pendleton Iron Works. Circa 1950, the firm merged into Radiation Ltd which was later acquired by 'TI New World'; 1902: Fletcher, Russell & Co. Ltd., Palatine Works, Warrington In 1880 gas -fuelled irons were connected by rubber tubing to the gas light-fittings of the house or to gas canisters. However , not many houses had access to a gas supply until much later and this iron was popular in 1920’sThese sad irons remind us of the difficult circumstances experienced in their daily routines by the pioneers and early settlers of Moorabbin Shire The family of Miss M Curtis were early settlers in Moorabbin Shire.A gas-fuelled flat iron, made in USA , It would have been attached to a gas hose fitting that was also used at night for light in the house. There is a small chimney to allow for air and to try to control the amount of heat in the iron. A 'shield' is under the leather covered handle to protect the user's hand from the heat, however it is made of copper metal - a heat conductor.FLETCHER RUSSELL CO. / LIM/ PATENT/ WARRINGTON on right side of handle 'Registered' on left side of handle ' Fletcher Russell Co L / Warrington, Manchester / & London.sad iron, kitchen equipment, fletcher russell co. ltd., england, warrington, manchester, pioneers, early settlers, market gardeners, sewing, craftwork, clothing, moorabbin, brighton, bentleigh, fireplaces, stoves, domestic gas supply, gas-light, gas cannisters

Cream, long sleeve shirt. Black and gold epaulettes. Gold crown above two gold embroidered anchors with gold "Australia" underneath.Do not boil or wring. Drip dry. Iron lightly with warm ironclothing

CAst iron lace was made in foundries in most cities. There were 42 such factories in Melbourne alone. It was cheaper to make than wrought iron. "Pig iron", iron ore, was melted in a blast furnace, mixed with alloys a nd then poured into moulds usually made of sand. The alloys needed a minimum of 2% carbon.A black and white photograph by Alan Doney of Early Nurses House Lucan Street (Bendigo Base Hospital). Now incorporated in portion of present Nurses home A Doney Bendigo - Copyalan doney, bendigo, wrought iron

A rim splitter was used on the outer rims of older vehicles to facilitate removal and replacement of tires. The tool was used to remove a tyre and replace it onto a split wheel rim. After the air was let out, the safety rim key was pulled. The swing arms were spread out and the three arms evenly spaced around the rim. The single arm with the screw gear needed to be close to the split so that the hooks fit on the rim and the rim was then pulled inward and the tyre could be be removed from the rim. After the tire was repaired or a new one was ready to be put on the collapsed rim the tool was used to push the rim back together and the safety key could be reinserted. A rim splitter were a universal type tool used for many cars of the 1920's and 1930's.A cast iron rim splitter which has two hinged side arms with hooked ends. The middle shaft has a hooked end and an inner bolt that can be screwed up or down.St Joseph Michigan Hercules Product Co Made in U.S.A. L 7motoring rim-splitter tyres tool

Pressed steel black ornate gaslight holder with two swirls- one above and below each other and cast iron flowers attached to the upper support. valve to turn the gas on and off.lighting, uebergang, allansford, domestic items, gaslight, gaslight holder

CAST IRON FEET FOR DISPLAY CABINET. Silver Chrome plated. Some significantly degraded chrome. Appear to be from a display cabinet. Approx 10cm in length. Curved shape. With filligree shapes

In conversation with Mr Tibbett we found out that he obtained this particular unit at an auction in Sydney and brought it home with the intention of one day getting it going again. 'One day' never seemed to come, so he decided to let us have it for our display, rather than jjust collecting dust in his shed.This unit is again of a different manufacturer and construction, highlighting the versatile nature of charcoal producer gas and its applications. A commercially made cast iron unit with a solid round hopper/boiler on a steelframe base. It has a pressure-cooker lid and a car type radiator. Solid built, but rust affected in partsMake: Tysons Cross Draught Model: Official 30hp Heavy Duty Serial: 1368

Cast iron copper with pull out door for fuel at base. Round copper insert with galvanised flue pipe. Round wooden top reinforced with two pieces of wood and a wooden handle.domestic items, laundering

Demonstrates a hand written note about the coefficient of friction.Foolscap sheet - titled "Some special Co-efficient of Friction" setting out parameters for steel tyres and rails, cast iron brake blocks, velocity and types of paving. Hand writtentrams, tramways, brakes, reports, tramcars

Part of series to record changes in BuninyongGrave of Buninyong Pioneer.A B/W and a colour photo, monument, polished granite, pillar on engraved plinth, urn cap, cast iron fence, for early settler George Innes and his daughter.. in Buninyong Cemetery.buninyong, cemetery, headstone, graves, innes, king of splitters, pound, buninyong defiance mine

Part of series to record changes in BuninyongGrave of Buninyong Pioneer.A B/W and a colour photo, monument, polished granite, pillar on engraved plinth, urn cap, cast iron fence, for early settler George Innes and his daughter.. in Buninyong Cemetery.buninyong, cemetery, headstone, graves, francis moss, tresise, apples

The first section of Studley House, now part of the preparatory school for Xavier College conducted by the Society of Jesus in Kew, was built in about 1857 for Parliamentarian John Hodgson, an early settler in the district, as a two-storey residence in the Classical Revival style. The name Studley House was first recorded in the Kew ratebooks in 1862, after the house was purchased in 1860 by James McEvoy, squatter. Alterations and an extension, designed by William J Ellis were undertaken in 1875. The house was again altered in 1919 during the ownership of John Wren, former bookmaker, ALP lobbyist, influential Irish-Catholic and millionaire. After 1969 the house was used by the school. (Victorian Heritage Database, 2023)This work forms part of the collection assembled by the historian Dorothy Rogers (1905-1973), donated to the Kew Historical Society by her son in 2015. The manuscripts, photographs, maps, and documents were sourced by her from both family and local collections or produced as references for her print publications. Many were directly used by Rogers in writing ‘Lovely Old Homes of Kew’ (1961) and 'A History of Kew' (1973), or the numerous articles on local history that she produced for suburban newspapers. Most of the photographs in the collection include detailed annotations in her hand. The Rogers Collection provides a comprehensive insight into the working habits of a historian from the 1960s to the 1970s. Original monochrome photograph of the view from the first floor verandah of Studley House in Nolan Avenue, Kew. The photo shows the detail of the cast iron lace work used on this section of the verandah.Annotation verso: "Lovely lacework of the balcony Studley House"dorothy rogers, studley house -- nolan avenue (kew)

Old cast iron butter churn stand, with four legs. Mechanism includes wheel, stand for container and handle. Signs of having been painted black, but paint has chipped offPlaque saying 'McCormick Deering Chicago USA, made by International Harvester Company' with makers symbol of 'C H H'food technology, dairying, butter, churn, dairy, milk, food, industry

Used by students at BurnleyWooden handles direct a metal chassis with two tynes attached and two cast iron spoked wheels. Pulled by second person with rope attached. Stencil of manufacturer painted on wooden handles.MINTERN D.W.HOE burnley college of horticulture, hoe, pedestrian plough, hand plough

This iron would have been used locally. Wehner's Blacksmith's was founded at Orbost in 1889. Oswald Wehner began working in 1910 with his father. In 1947 Ossie's son, Tom started blacksmithing, working alongside his father. Wehner's closed in 1991. (ref. In Times Gone By - Deborah Hall)This is an example of an implement used locally in the livestock industry in the last century. "Wehner's Blacksmiths was an important part in the business life of Orbost and was probably the most recent business to close with a link to our past." (Deborah Hall)Branding iron with either M or W as the brand. Circular, hanging.branding-iron rural-industry livestock

Thomas Crouch Watts was born on March 7th. 1865, to Joseph and Susan Watts. Before the real estate business commenced, Thomas and his brother were in partnership as booksellers and stationers in a shop at View Point. Thomas lived in a fine house in Rowan Street, which was called 'Ottawa' Thomas started his real estate business in the early 1900s in a shop in View Street. His daughter Edna was the book keeper and typist, Stewart Watson was the salesman and Stanley Phipps (Edith Lunn's father) was the property manager and valuer. When Thomas Watts died in 1914, his daughter took over the running of the business. She married Stewart Watson in 1918. Eventually the name of the business was changed to Bishop and Earl. From a letter from Edith Lunn re T.C. Watts & Son. 'The firm of T.C. Watts & Son later became Bishop and Earl. When the firm of Bishop and Earl ceased to operate after the death of Edith Lunn's father, S.P. Bishop, Miss. June Parry, Secretary of the BHS was a member of staff. June rescued all the photos of properties listed for sale from the office and placed them into the custody of the BHS.' Black and white photograph: weatherboard house, corrugated iron roof, bullnose verandah, picket fence, cast iron lace, one chimney visible , central door, window each side of front door, wrought iron gate. 'Mr Syme, Houston Street, Bendigo' written on back of image. 'Date 16 May 1930'. 2012 photo of the house attached to the record.Frank A. Jeffreebendigo, business, t.c. watts & son, t.c. watts collection, real estate

W.J. CHAMPION OWNED A GENERAL DRAPER SHOP IN FRASER STREET, CLUNES FOR MANY YEARS. TWO STOREY BUILDING, THREE SHOP WINDOWS, IRON VERANDAH POSTS, ORNATE CAST IRON DECORATION ON TOP OF POSTS..1 SEPIA PHOTOGRAPH MOUNTED ON CARDBOARD OF W. J. CHAMPION SHOP, FRASER STREET, CLUNES, GROUP OF GENTLEMEN IN FOREGROUND. .2 BLACK AND WHITE COPY OF THE ABOVE PHOTOGRAPH PRINTED ON GLOSS PHOTOGRAPHIC PAPERlocal history, photography, photographs, shops, w.j. champion.[ 2 storey building], buildings

Coopers tool for making wine barrelsWooden handled bow shaped planeAlan Patent Cast Steel

Vertical cylinder steam engine painted black, red and grey. In working order. Large flywheel and pulley on RHS and mounted on a raised concrete base. Belt drive overhead governor.No. "8532" is cast on the LHS of the frame.engines, steam, vertical

Zeehan & North East Dundas Tramway Bogie 1896 The North East Dundas Tramway (NEDT) was a 2 ft (610 mm) narrow gauge tramway on West Coast Tasmania that ran between Zeehan and Deep Lead (now Williamsford). It was part of Tasmanian Government Railways. The line was opened in 1896 to carry ore from the Williamsford mines to Zeehan where it would be loaded onto another train for shipment to Burnie. The narrow-gauge (2 ft) was chosen because of the extremely difficult terrain that the railway crossed, requiring several big trestle bridges, including one at the foot of Montezuma Falls. After some rain the engine and carriages would get soaked by spray from the falls. There was a break-of-gauge with the mainline 1,067 mm (3 ft 6 in) system at Zeehan. The railway was closed in 1932. The rolling stock for the Tramway was built in the Launceston Railway workshops, and comprised twenty five eight-wheel low-side trucks, tare 3 tons 1 cwt. 1 qr., load 10 tons; six eight-wheel flat trucks, tare 2 tons 18 cwt. 1 qr., load 10 tons; two four-wheel bolster trucks, for carrying long timber, tare 1 ton 19 cwt., load 5 tons; and four passenger cars, each with six cross-seats with reversible backs, to carry eighteen passengers, also a locker for mails and parcels. All trucks and cars have cast-steel wheels 21 inches in diameter and are fitted with automatic vacuum brakes. The trucks have side levers and the cars have hand-screw brakes. The vacuum brake can be worked from the engine or from the passenger cars, which act as brake vans. When this brake was introduced, one effect was to accelerate the journey speed by about 10 minutes owing to more even running on down gradients. Historic - Industrial Narrow Gauge railway - Bogie used on the Zeehan & North East Dundas Tramway, Tasmania, Australia Bogie made from steel, iron and wrought ironZN & NTDS ML TRAM 1896 Griffinpuffing billy, bogie, zeehan & north east dundas tramway bogie, zeehan & north east dundas tramway, industrial narrow gauge railway, gauge: 2' (610 mm)

A soldering iron is a hand tool used in soldering. It supplies heat to melt solder so that it can flow into the joint between two workpieces. The iron was heated over a fire or in a charcoal brazier. Soldering irons were primarily used by tinsmiths and coppersmiths to work with thin sheet metal. These hand soldering irons have been replaced by electric ones.Used by coppersmiths and tinsmiths and workers in the Kiewa Valley.The soldering irons have a wooden handle, an iron rod and are made of copper at the pointy end (the bit).shaped like a pyramid.soldering iron, hand tool, coppersmith, tinsmith

Langlands Company History: Langlands foundry was Melbourne's first foundry and iron shipbuilder established in 1842, only 8 years after the founding of the Victorian colony by two Scottish immigrants, Robert Langlands and Thomas Fulton, who had formed a partnership before emigrating (1813–1859). The business was known as the 'Langlands Foundry Co'. Henry Langlands (1794-1863), left Scotland in 1846 with his wife Christian, née Thoms, and five surviving children to join his brother Robert. By the time he arrived in early January of 1847 the partnership of Robert Langlands and Fulton had dissolved as Fulton had gone off to establish his own works. It was at this time that the two brothers took over ownership of Langlands foundry. Several years later Robert retired and Henry became sole the proprietor. The foundry was originally located on Flinders Lane between King and Spencer streets. Their sole machine tool, when they commenced as a business, was a small slide rest lathe turned by foot. In about 1865 they moved to the south side of the Yarra River, to the Yarra bank near the Spencer Street Bridge and then in about 1886 they moved to Grant Street, South Melbourne. The works employed as many as 350 workers manufacturing a wide range of marine, mining, civil engineering, railway and general manufacturing components including engines and boilers. The foundry prospered despite high wages and the lack of raw materials. It became known for high-quality products that competed successfully with any imported articles. By the time Henry retired, the foundry was one of the largest employers in Victoria and was responsible for casting the first bell and lamp-posts in the colony. The business was carried on by his sons after Henry's death. The company was responsible for fabricating the boiler for the first railway locomotive to operate in Australia, built-in 1854 by Robertson, Martin & Smith for the Melbourne and Hobson's Bay Railway Company. Also in the 1860s, they commenced manufacture of cast iron pipes for the Board of Works, which was then laying the first reticulated water supply system in Melbourne. Langlands was well known for its gold mining equipment, being the first company in Victoria to take up the manufacture of mining machinery, and it played an important role in equipping Victoria's and Australia's first mineral boom in the 1850s and 1860s. Langlands Foundry was an incubator for several engineers including Herbert Austin (1866–1941) who worked as a fitter at Langlands and went on to work on the Wolesely Shearing machine. He also founded the Austin Motor Company in 1905. Around the 1890s Langlands Foundry Co. declined and was bought up by the Austral Otis Co. in about 1893. History for Grimoldi: John Baptist Grimoldi was born in London UK. His Father was Domeneck Grimoldi, who was born in Amsterdam with an Italian Father and Dutch mother. Domeneck was also a scientific instrument maker. John B Grimoldi had served his apprenticeship to his older brother Henry Grimoldi in Brooke Street, Holburn, London and had emigrated from England to Australia to start his own meteorological and scientific instrument makers business at 81 Queens St Melbourne. He operated his business in 1862 until 1883 when it was brought by William Samuel and Charles Frederick, also well known scientific instrument makers who had emigrated to Melbourne in 1875. John Grimoldi became successful and made a number of high quality measuring instruments for the Meteorological Observatory in Melbourne. The barometer was installed at Warrnambool's old jetty and then the Breakwater as part of the Victorian Government's insistence that barometers be placed at all major Victorian ports. This coastal barometer is representative of barometers that were installed through this government scheme that began in 1866. The collecting of meteorological data was an important aspect of the Melbourne Observatory's work from its inception. Just as astronomy had an important practical role to play in navigation, timekeeping and surveying, so the meteorological service provided up to date weather information and forecasts that were essential for shipping and agriculture. As a result, instruments made by the early instrument makers of Australia was of significant importance to the development and safe trading of companies operating during the Victorian colonies early days. The provenance of this artefact is well documented and demonstrates, in particular, the importance of the barometer to the local fishermen and mariners of Warrnambool. This barometer is historically significant for its association with Langlands’ Foundry which pioneered technology in the developing colony by establishing the first ironworks in Melbourne founded in 1842. Also, it is significant for its connection to John B Grimoldi who made the barometer and thermometer housed in the cast iron case. Grimoldi, a successful meteorological and scientific instrument maker, arrived in the colony from England and established his business in 1862 becoming an instrument maker to the Melbourne Observatory. Additional significance is its completeness and for its rarity, as it is believed to be one of only two extant barometers of this type and in 1986 it was moved to Flagstaff Hill Maritime Village as part of its museum collection. Coast Barometer No. 8 is a tall, red painted cast iron pillar containing a vertical combined barometer and thermometer. Half way down in the cast iron framed glass door is a keyhole. Inside is a wooden case containing a mercury barometer at the top with a thermometer attached underneath, each with a separate glass window and a silver coloured metal backing plate. Just below the barometer, on the right-hand side, is a brass disc with a hole for a gauge key in the centre. The barometer has a silvered tin backing plate with a scale, in inches, of "27 to 31" on the right side and includes a Vernier with finer markings, which is set by turning the gauge key. The thermometer has a silvered tin backing plate with a scale on the left side of "30 to 140". Each of the scales has markings showing the units between the numbers.Inscription at the top front of the pillar reads "COAST BAROMETER" Inscribed on the bottom of the pillar is "No 8". and "LANGLANDS BROS & CO ENGINEERS MELBOURNE " The barometer backing plate is inscribed "COAST BAROMETER NO. 8, VICTORIA" and printed on the left of the scale, has "J GRIMOLDI" on the top and left of the scale, inscribed "Maker, MELBOURNE". There is an inscription on the bottom right-hand side of the thermometer scale, just above the 30 mark "FREEZING" Etched into the timber inside the case are the Roman numerals "VIII" (the number 8)flagstaff hill, warrnambool, maritime village, maritime museum, flagstaff hill maritime museum & village, shipwreck coast, great ocean road, warrnambool breakwater, coast barometer, coastal barometer, barometer, weather warning, ports and harbours, fishery barometer, sea coast barometer, austral otis co, coast barometer no. 8, henry grimoldi, henry langlands, john baptist grimoldi, langlands foundry co, meteorological instrument maker, robert langlands, scientific instrument maker, thermometer, thomas fulton

Publicity photograph of the cast from 'Cop Shop': [Back row] Paula Duncan, John Orcsik, Lynda Stoner, Gregory Ross, Terry Donovan, ?, Joanna Lockwood, Peter Adams. [Front row] Terry Norris, Louise Philip, Gil Tucker. Signed on the back 'To Neil, All my best, Gregory Ross. 3AW Yvonne Lawrence card is unsigned, however Bruce Mansfield and Philip Brady have autographed their with the first name only.1 black and white publicity photo of the cast from the TV show 'Cop Shop', 2 postcard sized publicity cards from 3AWnon-fictionassociation for the blind, elizabeth maxwell, neil maxwell, gregory ross, bruce mansfield, philip brady

The donor inherited this Wardana machine from her mother, who bought it in about 1933 and used it to sew garments for her sister's dressmaking business in Frankston, Victoria. The donor often used this machine until she purchased an updated model. There were originally three Ward Brothers who owned the North Melbourne sewing machine business but they had a falling out. This machine's decals on the map of Australia only include the two remaining brothers. The Ward Brothers, G & S Ward, established their sewing machine business in North Melbourne in 1888. The cabinets and ironwork of the machines were made in Australia and the Ward Bros. imported their machines from overseas manufacturers in England, America and Germany. The assembled machines were sold under brand names that included Ward, A.N.A. the patriotic-sounding Australian Sewing Machine Company. The "Wardana" was one of their brands.This sewing machine was fabricated in Australia from imported parts from England, giving a snapshot into the early manufacturing industries that were operating at the time just after Federation.Sewing machine in a wooden cabinet with iron foot-operated cast iron treadle mechanism. The hinged cabinet top opens out to form a worktop. The sewing machine lifts out of the cabinet to sit level with the worktop, resting on two supports within the cabinet. The lockable cabinet door opens from right to left revealing fitted shelves and spikes for spools and bobbins. The gold-painted maker's name is cast into the black treadle. The machine has its original instruction book, oil can, and eighteen accessories in an enclosed cardboard box. The round shallow oil bottle has a rubber dispensing tube. Colourful decals decorate the black body of the machine. Inscriptions include a Serial Number stamped on the bed of the machine. The Wardarna Central Bobbin machine was made in England for the Ward Brothers of North Melbourne.TREADLE: cast into metal ACROSS THE TOPE AND ON THE FOOTPLATE "WARD", "WARD" SERIAL NUMBER stamped into oval plate "28383" DECAL: (Map of Australia ) with images of [two brothers] , "WARDANA" above (logo of the rising sun) DECAL: (Decorative floral design with heraldic-like emblems) above "MADE IN ENGLAND" ARM: "WARDANA" PEDESTAL: "C.B." (representing Central Bobbin) "MADE IN ENGLAND" "MADE IN ENGLAND / FOR / WARD BROS / NORTH MELBOURNE" BOOK TITLE: "Instructions for Treadle Machine" ACCESSORIES: some have indecipherable embossed stamps OIL BOTTLE base: (image of log and short lines radiating from a central inscription (indecipherable)sewing machine, domestic, wardana, ward bros., central bobbin, made in england, north melbourne, c.b., flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, treadle sewing machine, home industry, clothing, dressmaking, clothing manufacturer

Melotte brand milk separator with red cast iron base and silver-coloured tin milk container and a separating can. A milk float sits in the top. The steel handle has a wooden grip.Melotte/ Supplied by T Robinson and Co Pty Ltd Spotswood Melbourneallansford, separators, dairying