Photocopy of 54 data sheets published by Westinghouse Electric & Manufacturing Company of East Pittsburgh Pa, USA c1920. Consists of plastic cover, header page with Westinghouse logo, contents sheets (2 pages), forward, 67 pages (single side photocopy) and heavy rear card cover bound with a green comb binder. Original material lent by Craig Tooke of the Melbourne Tramcar Preservation Association at Haddon. Photocopied by Warren Doubleday March 2000. List of contents produced 30/6/2000 and then bound. Contains data sheets regarding motors, commutators, brushes, armatures, bearings, field coils, pinions, lubrication, air piping, axle collars, resistance grids, gear cases and other technical information. Westinghouse Railway Operating Data 30/6/2000 List of Contents Page No. Care and repair of commutators 1 Undercutting commutators 2 Railway Motor carbon brushes 3 Brush holders 4 Flashing of railway motors 5 Soldering railway armatures 6 Armature Winding 7 Banding armatures 8 Railway Motor Bearings 9 Lubrication of railway motor bearings 10 How to babbitt motor bearings 11 Oil, grease and waster for motors and gears 12 Saturation of motor bearing waste 13 Testing Polarity of Field Coils 14 Charging of storage batteries on Interurban & street rail cars 15 Precautions to be taken with blower installations on motor cars 16 Putting on Railway Motor Pinions 17 How to take armatures out of box frame motors 18 Dipping and Baking of Railway Motors 19 War time dipping and baking outfits 20 Dipping and baking railway motors will decrease troubles 21 Protection of Motor Bearings from Dust 25 Winter Operation of Railway Motor equipments 26 Installation of Air piping to prevent freezing 27 Maintenance of Traction Brake Equipment 28 Maintenance of controller fingers and contacts 29 Hand operated circuit breakers 30 Railway Motor Testing I 31 Railway Motor Testing II 33 Railway Motor Testing III 35 Railway Motor Testing IV 36 Railway Motor Testing V 37 Removing and replacing railway motor armature shaft 39 Mounting and Maintenance of car resistors 40 Lubrication of control apparatus 41 Maintenance of fuse boxes for railway service 42 Does it pay to dip and bake armatures 43 Dipping and Baking as a financial asset 44 Shop Organisation 45 Tinning Malleable Iron Bearing shells 46 Life of armature bearings or railway motors 47 The assembly of complete sets of commutator segments 48 Electric welding as a factor in reclamation 50 Metal to Metal press, shrink and clamping fit allowances 52 Life of railway motor carbon brushes 54 General information of grid resistance design for the operating man 56 Stopping a car by braking with the motors 57 Railway Motor shafts and their maintenance 58 Axle collars 59 Gear cases 60 Ventilated railway motors 62 Revamping Loose armature bearings 64 Life of axle bearings of railway motors 65 Heat-treated bolts for railway service 66 Document imaged over 7 parts 7-9-2016 - see hi res files. trams, tramways, westinghouse, motors, data sheets, technical information

One of a group of signs that were fitted into tramcars in Ballarat, giving instructions to passengers about prams, behaviour, smoking, fare payment, talking to the motorman, instructions or information to drivers etc. Yields information about the sign manufacture, demonstrates the type of signs provided in tramcars.Enamel sign, black capital letters and lines on white background, titled "Passengers are requested not to enter into conversation with the motorman when tram is in motion". One of a number similar signs donated to the Ballarat Tramway Preservation Society by the SEC following closure of the Ballarat Tramways system in 1971. Sign has a black enamel backing, with marks from the enamelling process. On the rear is part of a paper sign about mounting the sign with screws and not using nails and the name of the manufacturer "Simpson & S? Pirie Street......" (See Reg Item 4899 for the full manufacturers label) .1 - As for above, added 31/12/2010/ trams, tramways, tramcars, signs, motormen, passengers

Yields information about the types of tramway signals available for use on tramways systems. The type BY was used by the SEC in Ballarat and Bendigo.Four page Pamphlet or Brochure Forest City ATS1, printed brochure with illustrations "Automatic Tramway and Crossing Signals" – four types noted. Four types: 1. Tramway type "C: Car counting signal, up to 10 cars 2. Tramway type "BY" - non car counting signals 3. Level crossing signal operated by approaching cars 4. Turning Warning signals with notes on rear page of the set up for automatic control signals for rail crossings on roads, docks etc. Date stamped by SEC 20/9/1949 on front cover.Has “218” in biro in bottom left hand corner.trams, tramways, forest city signals, level crossings, signals

Yields information about the types of automatic point Turing mechanisms used on tramway systems, not actually used in Ballarat or Bendigo.Four page Pamphlet or Brochure Forest City No. 19, "Collins Patent Automatic Point Turner". Four page printed brochure with illustrations 1940’s? describing the Point turning mechanism with illustrations, of the equipment, method of operation advantages, wiring, the street box and curb (kerb) control box. c1940's? Has “217” in biro in bottom left hand corner.trams, tramways, forest city signals, level crossings, signals

Circulated between 1966 and 1984, the one dollar bank note was issued following Australia's switch to decimal currency. It was later replaced by the dollar coin. Legal tender throughout the Commonwealth of Australia and the territories of the Commonwealth. Issued by the Reserve Bank of Australia, with the signatures of both the Governor of the Reserve Bank (J.G.Phillips), and the Secretary to the Treasury (R.J.Randall) noted on the obverse. Australian one dollar notes carry individual serial numbers.Demonstrates the one dollar note as it was circulated in Australia between 1966 and 1984. It represents currency used by Ballarat passengers to pay their tram fares, and received by SEC Ballarat Tramway crews/staff in wage packets.Orange, yellow and brown minted note on white treated paper. The obverse depicts Queen Elizabeth the II, the Australian Coat of Arms and the "1" denoting value. The reverse depicts Aborginal drawings, including animals and people, as well as the "1".btm, cash, bank notes, australian currency, ballarat tramway museum, australian one dollar note

Circulated between 1966 and 1988, the two dollar bank note was issued by the Reserve Bank of Australia following Australia's switch to decimal currency. It was later replaced by the two dollar coin. Legal tender throughout the Commonwealth of Australia and the Territories of the Commonwealth. Signed by J G Phillips, Governor of Reverse Bank of Australia, and R J Randall, Secretary to the Treasury. Each note is assigned a unique serial number, this notes serial number reads GJJ 982843.Demonstrates the two dollar note as it was circulated in Australia between 1966 and 1988. It represents currency used by Ballarat passengers to pay their tram fares and received by SEC Ballarat Tramway crews/staff in wage packets. Green and yellow minted note on treated white paper. Obverse depicts John Macarthur, a merino ram and a "2" denoting its value. The reverse depicts William James Farrer, alongside ears of wheat and the "2".btm, ballarat tramway museum, cash, bank notes, australian currency, money, two dollar bank note

Used by the Forrest City Signal system to initiate or cancel a signal indication. The trolley wheel would make contact with the steel strips which would send an electrical impulse to the control box that either would enable the signal to be shown or cancelled. There was one on the trolley wire at either end of the section. See reference for further details.Demonstrates part of the Forest City Signal system.Signal contactor mechanism comprising two brass ears, a section of copper trolley wire, two steel strips assembled onto a section of wood fitted with steel covers where the ears are fitted through. Item refurbished for display purposes by Depot staff 2023.forest city signals, tramways, overhead