The Harris blue electric trains were introduced in c1955 and followed the 'Red Rattlers'. They had a long life and were named after Norman Charles Harris, Chairman of Commissioners of the Victorian Railways, between 1940 and 1950. The first 30 7-carriage trains, known as the first series, were constructed in the United Kingdom by Gloucester Railway Carriage and Wagon Company, and delivered between 1956 and 1959. Another 30, the second series, were built by Martin & King in Melbourne, and delivered between 1961 and 1967. The trains had either two or three sets of hand-operated dual sliding doors per carriage side. Later they were fitted with power doors. Initially, until late 1978, the interiors were split into smoking and no-smoking compartments. In 1978 smoking on trains was abolished. Carriages were also designated as First or Second class until 1958, when one class travel was introduced. they had florescent lights but no heating. Most of the early carriages did not have end doors and gangways between carriages, but safety concerns led these being incorporated in the sets delivered from mid-1966. With the exceptions of the last few carriages built, all Harris trains contained asbestos insulation. The first sets contained blue asbestos, and the later sets contained white asbestos in the linings for insulation of noise and temperature. Due to the presence of asbestos, they began to be withdrawn from the mid-1980s and most were disposed of in the 1990s, by being buried at Talbot Quarry in Clayton, some having been wrapped in plastic. No original Harris trailer cars remain. A coloured photograph of a blue Harris electric train heading towards Surrey Hills station from Mont Albert station. The electricity sub-station and Lorne Parade are on the RHS of the photo and Beresford Street on the LHS. The grey, smoggy appearance of the sky suggests a winter's morning.surrey hills, trains, lorne parade, beresford street, norman charles harris, gloucester railway carriage and wagon company, martin & king, talbot quarry, harris blue train

To celebrate Christmas and advertise Carols by Candlelight, the property team put up a number of external decorations on the Glenferrie Road side of the building at Kooyong.5 images of reindeer lights and banners displayed for Christmasvision australia, carols by candlelight

The photograph of the Royal District Nursing Service (RDNS) Holden Torana vehicles was taken in the RDNS Headquarters car park at the rear of 452 St Kilda Road. These cars are part of the RDNS fleet, with others housed at RDNS Centres. The cars were used by the RDNS District nurses to visit patients in their own homes. This photograph depicts two door Holden Torana cars of 1972.Royal District Nursing Service (RDNS) has had various modes of transport over the last 130 plus years. At first, from 1885 as Melbourne District Nursing Society (MDNS), their Trained nurses (Nurses) walked the streets and lane ways amid the slums of central Melbourne. As the Society expanded public transport was used, and bicycles were bought by the Society in 1903 and used in inner areas until 1945. During the Spanish flu epidemic, in 1919, MDNS appealed for assistance to procure Motor vehicles so the Nurses could visit an influx of cases. Through trusts, grants and donations four 'Ford T Model' cars were procured which enabled the Nurses to triple their visits. Through constant use the cars were in such a poor state two were sold in 1922 and the others later. In 1922-23 three Peugeot cars were purchased and a woman Chauffeur, 'Miss Sword', was employed who lived in the Home and was also in charge of the garage. MDNS was expanding and a Motor Auxiliary was formed in 1929 to take the Trained nurses (Sisters) to patients, and some Sisters used their own cars; even a motorcycle was used by one Sister in 1933. All these forms of transport were intermingled and in the early 1950s, and now as Melbourne District Nursing Service, seven Ford Prefect cars were bought followed by twelve Ford Anglia cars 1955. Having received Royal patronage; the now Royal District Nursing Service (RDNS) had its own fleet of Holden vehicles by the mid 1960s and the Motor Auxiliary ceased operating in 1971 as by then all staff employed were required to have a driving licence. Seat-belts had been introduced to Victoria in 1959 and District fitted them to their cars from 1962, even though they did not become compulsory until 1970. The Holden vehicles were replaced with grey Holden Torana vehicles. After several years the fleet was changed to white Toyota Corolla vehicles. The Melways Directory of maps was introduced in 1966, which was a boon to the Sisters, though it was a few years before it went beyond Seville, so a large paper map was used by the Sisters visiting patients in the areas passed Seville. By 2009 there were 598 cars in the fleet and the Sisters travelled 9 million 200,000 kilometres – this is equivalent to 12 trips to the moon and back. Black and white photograph of 14, some partly hidden, new grey Holden Torana two door vehicles parked in two rows in the RDNS concrete based car park. The cars are parked with their front lights, grill, bumper bars and number plates facing the left of the photograph. The cars are seen side-on with the full side-on view of the two cars at the beginning of the rows seen in the foreground of the photograph. The flat bonnet is the same width as the rest of the body of the car; the windscreen slopes upward and joins the flat roof; there are two wiper blades resting at the base of the windscreen. In line, and at the level of the windscreen, a quarter window, and two windows divided by a narrow pillar can be seen running along the side of the car above the slightly convex body work and front door. The rear window slopes back from the roof and the slope continues on the upper bodywork of the boot lid. A metal strip runs along the side of the car about half way down the bodywork, and another runs just up from the beginning of the front wheel arch to the rear wheel arch; beside the front wheel arch is the word 'Torana'. The round, with capital letters 'RDNS', insignia can be seen on the upper centre of the front door of the two cars. The solid wheel caps have the Holden logo on them. The front grill which runs between the headlights on either side of the car, slopes slightly backwards from the central Holden badge. The bumper bar below this is metal. Black number plates with white written capital letters and numbers 'LFA - 208' and 'LFA - 207' are seen on two of the cars in the front row. The tops of two front seats with headrests and the top of a long back seat can be seen inside the car. A tall brick fence is seen running along the rear and right hand side of the car park. In the left background is a two storey building with a flat roof, and behind this on its left is a part of a tall building and to its right part of a bare tree can be seen. To the buildings right rear part of a house can be seen. In front and to the right of this is a three storey brick building, with the top two storeys seen above the car park fence. Multiple windows run along both levels of this building which has a tiled hip roof. The tops of some bushes are seen behind parts of the car park fence.Barry Sutton Photographer's Stamp Quote KX83rdns, royal district nursing service, rdns transport, rdns headquarters, rdns car park

Detached sector panel from upper lantern. The lens segment is one of a pair of freestanding panels that formerly stood on a platform in the upper lantern room on either side of a small fixed light. The platform rested above the 1860/62 Chance Bros. first order, fixed lens and could be accessed by a ladder. The two sector lens panels were each set in a bronze frame and comprised a curved wider (belt) piece in the centre with nine curved, slim line pieces above and below it (19 pieces in total). The belt aligned with the light source to provide optimal focus and range. The panels, the light and the platform were installed in 1934 to upgrade the original optical system with red warning lights. Fitting them above the lantern was a convenient and inexpensive way to do this, with each lens panel set up behind a red glass panel to project a red sector to the seaward over to Cape Howe and the Western Shore. The two sectors are likely to be Chance Bros. by manufacture although they do not appear to bear the maker’s name. This is probably because Chance Bros. typically fixed metal plaques to their apparatus and tended not to stamp smaller components such as their lens frames. It could possibly indicate that the two sectors are former components of a larger system, i.e. another lens. This can easily be confirmed by closely inspecting the bronze frames. A series of holes on the frame would indicate that ‘they would have bolted to other panels to make a larger lens assembly’. The absence of holes would confirm that ‘they were made specifically to stand alone’. The sector panels were removed from the Gabo lantern in February 1992. At some point after their removal, they were found in boxes marked with ‘Ince Pt.’, however it is thought that Ince Point lighthouse ‘never had … stand alone sectors’. The panel in the Gabo Island collection is one of two segments discovered at the Eden Killer Whale Museum in about 2007. One section was repatriated to Gabo Island and the other was to go to Smoky Cape Lighthouse in northern NSW. The Gabo lens segment has first level contributory significance for its historic value and provenance to the lantern room. It is recommended that Parks Victoria/AMSA seek to return the Smoky Cape segment to Gabo Island and reunite the sector panels.The Gabo lens segment has first level contributory significance for its historic value and provenance to the lantern room.Section of a lens from a lighting apparatus , rectangular louvers of glass enclosed in a metal frame.

The kerosene container is documeted as having been used to fill slush lamps, hand lamps and train engine lights, and is part of the Wodonga Historical Society's railways collection.The kerosene container has local significance as it was donated by a Wodonga resident and is part of Wodonga Historical Society's railways collection. It is documented as having been used to fill slush lamps, hand lamps and train engine lights. Grey metal kerosene container with a looped handle attached to the sides, as well as a handle on the back of the container with a metal chain attached to it to secure the cap for the container. Used to fill slush lamps, hand lamps and train engine lights.kerosene container, kerosene bottle, fuel for railway lamps

This image is representative of many photographs illustrating the level crossing in the centre of Wodonga. Since its opening in 1873 the railway line had crossed High Street, originally called Sydney Road. It bisected the city with level crossing gates frequently stopping the flow of traffic and pedestrians as trains passed through. Signal Box B stood on the eastern side of the High Street level crossing and a big wheel closed and opened the gates. On 17th September, 1961, it was replaced by boom gates and flashing lights. The railway crossing was removed from High Street as part of the Wodonga Rail Bypass project. This involved a 5.5 kilometres bypass, the elimination of 11 level crossings and the relocation of the Wodonga station. It was moved from its original central location to a position on a new line on the northern edge of the town. The old station closed on 8 November 2008 and the new station opened on 25 June 2011.This image has local and statewide significance as it captures the former crossing in a major railway system. The railways played a critical role in opening up Victoria and connecting Australia for trade, business, social communication and transport.A black and white photo of the railway level crossing in High Street, Wodonga with gates closed. The Melbourne to Sydney railway line went through the centre of Wodonga and trains frequently held up internal vehicular and pedestrian traffic in the main street. railways wodonga, wodonga railway relocation, high st wodonga rail crossing

"Summer Car" 11 outside Mac's Hotel in Corio Tce. To the right is Strachan, Murray and Shannon's wool store whose facade still stands. The tramcar, shown in pristine condition was one of the two trailers motorised in 1913 with equipment identical to that of the Duncan & Fraser cars. They were built for use mainly on the new South route to the Barwon River. The coloured destination lights were from left: Red for GEELONG WEST, blank (later blue for the East route), white for SOUTH GEELONG and green for NEWTOWN. Side destination boxes have been added. Late 1913.Black and white print on paperNo. 1 inside a circle, and 13-7 written in ink on reverse. GSR7109/13/1/7 written on reverse in pencil.geelong tramway summer car 11, geelong streetscape, geelong tramway motorised trailer, geelong tram destination lights

Mrs Goldsmith died on 24th February 1951. Annual Report 1952: "Mrs Goldsmith Memorial: The new fault stool placed in the chapel in memory of Mrs Goldsmith was dedicated on Sunday, May 18. It was unveiled by Miss Maud Breaks in the presence of many old friends and correspondents."Wooden stool with kneeler covered with red vinylOn the plaque located on the right side: A.D.G. / In Loving Memory of / Annie Goldsmith / Widow of the Late Rev. A.G. Goldsmith / Died at Cullompton, England, On February 24th 1951 / This mMemorial Given by Friends and / Members of the Harbour Lights Guildanne treverton goldsmith (nee lobb), cullompton

Rose Series postcard No. P 10526 titled "Swanston St looking south Melbourne", from just north of Collins Stret. Trams in the view are S class No 164 and W class No 381? On the left side is a cable tram in Collins Street waiting to cross Swanston Street. An early MMTB bus is also heading south in Swanston Street with motorcycle and side car behind it. The cable tram signal is visible just to the left of the bus. This signal would continue to control all tram movements through the intersection until the insulation of modern motor traffic lights around 1929. On the left of photo is the imposing Queen Victoria building demolished in the mid 1960's to make way for the City Square. Yields information about Swanston St. at the intersection with Collins St.Postcard - printed real photograph with Rose Stereograph Co. name on the rear. Unused.trams, tramways, swanston st, s class, tram 164, cable trams, signals, w class, collins st

Date made January 2009Colour photograph showing western side of western pier. Rocks extend from end of pier along base of sand dunes, some vegetation on dunes. Signs and lights on piers. Lakes Entrance Victoria topography, beaches

Francis Powell (1861-) and Francis Hanmer (1858-1925) founded Powell and Hanmer Ltd in the Summer of 1885 for the manufacturer of bike and carriage lamps. Their first advertisements began to appear in November of 1885. Early models of the automobile, motorbike and bicycles used carbide lamps as headlamps. Acetylene gas, derived from carbide, enabled early automobiles to drive safely at night. Thick concave mirrors combined with magnifying lenses projected the acetylene flame light. These type of lights were used until reliable batteries and dynamos became available, and manufacturers switched to electric lights.Acetylene bicycle light carbide. Green and red side lens. 200 cm High. Inscription Powell & Hanmer Birmingham. Previous Catalogue Number 112.lighting, accessories, bicycle light

Car was built by GM Thailand designed by HoldenDesigned in AustraliaBronze orange body. Roof rack. Snorkel mounted on front panel. Driving lights mounted on roof rack. Winch on front bumper. Off road wheels and tyres. Crew cabin utility vehicleHolden emblem front grille. Z71 4X4 on panel in roll bar. Colorado XTreme on back and both sidesvehicle, holden, off road

2013 Concept pilot used for media release of VE sedans. Engine is a High performance V6 . ( No V8 available in this model)Built by GMH in Elizabeth (South Australia) as promotional pre release vehicle4 Door sedan .Nitrate (Silver - Grey) Side indicators mounted on vents on front quarter panel. Day running lights together with fog lights lower front bumper. Alloy wheels, pronounced chrome grilleRound Holden emblem both centre grill and boot lid, Calais on LHS Boot lidholden, ve concept, calais

This distress EPIRB unit (Emergency Position Indication Radio Beacon) was found on the beach at Levy's Point, Warrnambool, in December 2000 by a Warrnambool resident. Local police were alerted at the time. This distress signal unit is a world-wide COSPAS/SARSAT, satellite assisted, SAR (Search and Rescue) system for location of distress transmissions emitted by an EPIRB. Offshore cruising vessels must have such a unit as part of its essential safety equipment. This model EPIRB relies on four satellites with orbit times of approximately 100 minutes. Earlier units relied solely on aircraft flying overhead to detect and forward on the EPIRB’s location to Search And Rescue authorities, whereas this new system utilises satellites. An employee from the Lokata firm provided additional information about the Lokata EPIRB units. They had a machined aluminium case with labels that were also made on site. The units could be activated manually or automatically released when a magnetic switch in the case casing was activated. This later model, circa 1983, would have been mounted externally on a vessel's bulkhead in a spring-loaded, stainless-steel protective 'skeleton' mounting, The unit released when the water pressure sensor detected a set time it was under the water, in a similar way that life crafts were released. Each unit was registered to a particular vessel - the vessel's details on this unit are indecipherable. The Lokata Company was established in 1970, designing and manufacturing marine products including communications. The company no longer makes products with the “Lokata” brand. In 2001 Sartech Engineering Ltd. took over the support for the Lokata EPIRB beacons. This emergency location device is a late 20th century invention to help save lives at sea. It adds to the history of maritime life, its risks, the lives lost as sea, and the many inventions aimed as rescuing and saving lives. The local area is notorious for the number of lives lost through shipwreck. It also carries stories of heroic efforts to save lives, and other inventions to help reduce the chance of accidents at sea.EPIRB unit; “Emergency Position Indication Radio Beacon”. A distress communication unit for sending a distress location transmission in an emergency at sea. The EPIRB is a yellow, rectangular box with dials, buttons, indicator lights and instruction. An antenna protrudes from the top of the unit. The EPIRB unit sends a 406P (X) EPIRB, with 406M-Hz frequency, 48-hour duration signal. The maker was LOKATA Ltd in England. Remnants of a white label remain on the side. Circa 1980s."NAME OF VESSEL 'SERVICE IF SELF TEST FAILS' " “LO-KATA” moulded into the body. "406P (X) EPIRB" “Model 406” "Lokata Type No 92408" "UK Type approved to MPT 1278" "Class 2" "Made by Lokata Ltd, Falmouth Cornwall England TR10 8AE"" "LOKATE LTD. New North Road Hainault, Ilford Essex IG6 2UR" "ARMED / SAFE / TRANSMIT / CODE / DISPLAY / SET / wait / pass / fail / TEST" "IDENTIFIER / 1349:24034234N" [some characters may be different] "COUNTRY / DENMARK" "VESSEL IDENTITY / 124 [the rest is indecipherable]flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, emergency position indicating radio beacon, epirb, lokata ltd, marine safety equipment, satellite transmitting beacon, safety equipment, distress signal, life saving, safety at sea, shipwreck location, lo-kata, falmouth, emergency, beacon, radio signal, communication, marine equipment

Black and white photograph of two single truck trams (No. 26 being the rear tram nearest to the photographer) at the City terminus in Sturt St. at the intersection with Lydiard St. Robert Burns statue in the background. Both trams in the intermediate scheme of lights but no large white strip under the dash canopy lights. This places the photog as being taken during the early 1961's onwards. Both trams have Briquettes roof advertisements. A bogie tram is on the other side of the road. No. 26 showing "Gardens via Sturt St. W". Two copies held.trams, tramways, sturt st., city terminus, tram 26

Yields information about the launch of the Gold Tram and the people involved on the day.Newspaper cutting, page 4, from The Courier, Ballarat, June 15, 2001, headed "TRAMS IN BALLARAT" featuring three different tram stories. Headed "STUDY" and titled "Tram study ready to go", about the consideration of tenders for the study to consider the return of trams to Ballarat, or other form of transport. Quotes Dianne Smith, Ballarat Tourism Executive Director. Headed "GOLD TRAM" and titled "Sparkling reminder of a golden past", about the launch of the Gold Tram 45, by the Mayor, David Vendy the previous day at the tram depot. Quotes Richard Gilbert as president and Cr. Vendy. Features a photograph of Cr. Liz Sheedy and the Mayor standing along side, breaking through the banner ( See Reg. Item 1777). See Reg item 3839 for a colour photograph of the photo of No. 45. Headed "TRACKS" and titled "Section torn from Skipton St" about the excavation of about 50m of track in Skipton St. Ballarat at the intersection with Drummond St. during the reconstruction of the intersection associated with installation of traffic lights and new traffic islands. Quotes Peter Winspur, Secretary. A number of calls were received about the work. See Reg. Item 1778 for photos on the day.ballarat city tramway, gold tram, skipton st, trackwork

The Panther lamp was made by Powell and Hanmer of Birmingham. (see Item 7354) This model appears to be dated from the 1920's. Early models of the automobile, motorbike and bicycles used carbide lamps as headlamps. Acetylene gas, derived from carbide, enabled early automobiles to drive safely at night. Thick concave mirrors combined with magnifying lenses projected the acetylene flame light. These type of lights were used until reliable batteries and dynamos became available, and manufacturers switched to electric lights.Carbide Vehicle Lamp.-Silvered Metal, Lens Assembly . Small Green lens on both sides of the assembly, with a clear lens in front. 'Panther B'Ham' is stamped on the lower part of the assembly. In addition a Logo is Stamped with 'P H' and 'Ltd' under those letters. Carbide Gas section missing.Panther B'Ham

Set of six magazines, A4 photocopied titled ""Around the Tracks Newsletter of the Workshops"" edited by Norm Cross stapled on the left hand side, during the early days of The Met. .1 - Issue 4 - 11 A4 pages, undated, cFeb.1985, titled suggested by Bruce Pyke, news from paint shop, body shop, MTA Cricket, machine shop, E. Sires President of the Shop Committee, plan of changes to Cameron Hall, floor plan, buy and sell. .2 - Issue 5 - 6 A4 sheets, printed on yellow paper, Paint shop news, Pete Budge Manning, Cricket news, history of 2001 written by Norm Cross, machine shop news, and for sale or buy. .3 - Issue 6 - 4 A sheets, poem "The lights of Cobb & Co", Workshops cricket trip April, Roachie & Yabby on Safari, general news and for sale and buy. .4 - Issue 7 - 8 A4 sheets, a crossword, general personal news, Apprentice Day and awards, includes a list of apprentices who completed their training including Craig Tooke, machine shop news, list of trams not repainted, Roachie & Yabby on Safari part 2, notice to employees about the microwave oven and prevention of back injuries. .5 - Issue 8 - 8 sheets mainly doubled side, printed on pink paper, minutes of the Workshops Consultative Committee, the use of MTA personnel at Mt Buffalo (written by Craig Roach - (The War that never ends"), Credit Union meeting, poem by Bobby Sparks (Chester), Malcolm, the Story of a film, new library books, changes to the workshops, new traverser. .6 - Issue 9 - Christmas - 11 A4 sheets single sided, body shop news, personality profiles, machine shop news, Fleeing the Killing fields (Cambodia) by John Prideaux, for sale and buy.Yellow highlighted applied where Norm's name is mentioned or his columns.trams, tramways, preston workshops, the met, cricket, sports, unions, cameron hall, apprentices, malcolm

Document - 9 A4 pages, stapled in the top left hand corner, photocopied double sided - titled "Instructions to Drivers on Z class trams". Provides information on the operation, faults, defects, line breakers, track brake, lights, points, PA, Safety, Hot Weather, design changes on Z5, notes on the Z3 tram, power limiting switch, overspeed, faults -when it will not drive. Dated 1/5/1989. Original copy replaced 1/7/2020 with a better copy from Keith Kings.trams, tramways, the met, drivers, driver training, instructions, ptc, z class

Set of two Black and White photographs of the front section of tram SW5 840 in Flinders Melbourne, tram has a Associated Securities Limited advertisement on the side of the tram. Tram has run number K5, route 48 and destination of Spencer St. Photo taken post August 1971 as the tram is fitted with Marker lights .1 - view of tram and a motor vehicle (Ford Galaxy) with a damaged front right headlight and minor damage to the tram front of the door post. Also note the damaged bumper bar on the car. .2 - photo of the tram crew looking at the front of the tram - Opps more paperwork.trams, tramways, flinders st, accidents, crews, route 48, motor vehicles, sw5 class, tram 840

Report and photographs of various mechanisms to identify and check clearances for Safety Zones on tramways. .1 - Report - 4 pages stapled in top left hand corner - titled "Interim Report - Nicholson Street Safety Bars", dated 20/6/1978 signed by R. G. Vanselow. Describes the work involved in providing a type of "jiggle bars" leading up to the safety zone. Many photographs of the various types of safety zone marks were included within the folder. The photos of 912 are related to the clearance testing carried out during 1973 for the Z class. See also Reg Item 480? .2 - tram 912 fitted with a wooden device to measure clearances - with a concrete safety zone being checked. .3 - tram 1040 in Bourke St with a Safety Zone sign on the left - King St? .4 - tram and traffic at the Bourke St terminus. .5 - not used. .6 - tram 1000 at ditto on a wet day .7 - as for .2 .8 - ditto .9 - ditto .10 - side on view of W2 447 with a concrete prow fitted with a set of flashing lights. .11 - to .15 - series of large prints of enlarged 35mm negatives of night testing of safety zone sign taken at South Melbourne Depot and in St Kilda Road. .16 Bourke St - looking west at Russell St? with caption "prow replacing type 2 (Hairpin sign) with both original (white) and new MCC (Yellow) line marking on approach". .17 - Bourke St - looking west at Kings St and caption "Prow replacing type 2 (Hairpin sign) with original line marking on approach. .16 and .17 taken on Polaroid Instamatic cameras.Some of the photos have captions written on the rear.trams, tramways, tram stops, bourke st, safety zone, testing, z class, safety, tram 912, tram 1040, tram 1000, tram 447

Set of two black and white photographs, of the front of a Mock-up tram at Preston workshops, the fore running of prototype tram 1041. In an e-mail of 2/9/2019, Mal Rowe advised: - > The second one I think is of a large model of the future 1041, of interest. > The left side photograph could be a model or an early rough-up of the mock up. The right side Photograph is probably the mock-up - judging by the window in the background. See: https://tdu.to/m/168842/melbourne-1040-and-a-half c late 1960's. The photo with the window in the background could be the actual mock-up (two copies held), while the 2nd is of a narrower body, but has workshop lights reflected in the window. All photos have a remnant of an adhesive strip on the rear.trams, tramways, prototype tramcar, preston workshops, models, 1041

Set of six colour prints of trams at Preston workshops 1979. .1 - 9W Scrubber on temporary cable tram bogies while body is repairs. Side panels have been removed. .2 - W2 234 (Transporting Art) and other stored trams. .3 - SW2 275 with lights on and a "Tram Alive" sign. .4 - Z1 class tram front with power on. .5 - Z2 114 being commissioned - vicsig.net gives the in service date of July 1979. .6 - PCC 1041 Printed on Kodak Papertrams, tramways, preston workshops, service tramcars, scrubber tram, transporting art, w2 class, z class, tram 9w, tram 234, tram 275, tram 114, tram 1041, pcc class, sw2 class, z2 class

Set of five Photographs, Black and White, of St Kilda Road, with works about to commence to convert the cable tram to electric trams. .1 - Overhead pole holes being dug in the one of the central plantations - pole and a Furphy water cart alongside. A cable tram is passing at speed. Note the scale of the houses opposite and the number of side walk superintendents! .2 - View of St Kilda Road with a few motor cars and one cable tram. Looking south on the Sth Melb. side. .3 - ditto, view of cable tram track, poles laid out on the central plantation, note the street lights. About seven cable trams in the view. Look south towards St Kilda Junction. The Junction hotel is in the view. .4 - similar photo, but further north. Cable trailer 74 in the view. .5 - View of St Kilda Road, vehicle road with a number of vehicles in the view. Looking south on the east side of the roadway. Photos Print and photograph by Sutcliffe of Cromwell buildings 366a Bourke St. Melbourne.In ink and pencil on the rear: .1 - "M&MTB H-60, Kew Depot `1920's (E45 in shed)" and the photographers stamp. .2 - "MMTB St Kilda Road about 1924" and in pencil "Tramway poles erected, pole not removed? Sth Melb side, looking south along motor track" .3 - As above - and in pencil - Tramway poles not erected - ????" .4 - As above with notes in pencil. .5 - As above with notes in pencil. About 1924 KSK print number SA932 to SA936.trams, tramways, st kilda rd, cable trams, conversion, trackwork, overhead, construction, tram 74

Set of four Photographs, Black and White, of the MMTB Tourist Bus late 1920's. .1 - Side on view of the MMTB Tourist bus showing the lettering and logo. .2 - Front on view showing the radiator, head lights and other details including the crank handle. .3 - Interior view looking along the bus from the front. Shows the curtains and the extensively upholstered seats. .4 - ditto showing the woven cane seats. Photos Print and photograph by Sutcliffe of Cromwell buildings 366a Bourke St. Melbourne.In ink on the rear: All "M&MTB Tourist bus late 1920's" and the photographers stamp, with .3 and .4 adding "Interior" KSK print number SA957 to 960trams, tramways, mmtb, tourist bus, buses, interiors

Set of two Photographs, Black and White, of the MMTB bus 7 - Tilling Stevens, petrol electric bus. .1 - Front on view showing the radiator, head lights and other details including the crank handle - shows the destination of Elsternwick via High St. Registration Number 68907. .2 - Side on view of the bus showing the lettering, logo, doorways and destination. Photos Print and photograph by Sutcliffe of Cromwell buildings 366a Bourke St. Melbourne.In ink on the rear: .1 - "M&MTB Tilling Stevens, Petrol Electric Bus No. 7, late 1920's. .2 - as above plus "33 seats" KSK print numbers SA951 and SA952.trams, tramways, mmtb, buses, elsternwick, tilling stevens, tram 7