The anchor is one of four that were carried by the FALLS OF HALLADALE when she was wrecked near Peterborough in 1908. This Rodger’s Anchor was raised from the wreck site by Flagstaff Hill divers (Peter Ronald, Colin Goodall and Gary Hayden) in 1974 and is on permanent outdoor display at the Maritime Village. The imposing 2-tonne artefact required a raft of fourteen 44-gallon drums to raise it from the seabed before it was towed by a crayfish boat to the wharf crane at Port Campbell for loading onto land transport. Following Lieutenant William Rodger’s patent in 1831, anchor design moved away from the separate attachment of straight arms and flat flutes to each side of a long shaft. Rodger’s innovation included the forging of both arms and their flutes as a single uniformly curved piece which was then attached to the crown of the shank by a thick horizontal bolt. The two-inch diameter hole for the securing through-bolt at the crown is clearly visible in this example, the bolt dislodged by corrosion and now missing. The FALLS OF HALLADALE was a four-masted, iron-hulled barque, built by Russell and Co at Greenock in 1866 for the Falls Line of Wright & Breakenridge, Glasgow. The ship was 275 feet long, 42 feet wide, with a 24 feet draft and weighed 2,085 tonnes. She was built to carry as much cargo as possible rather than for speed. Her unmistakably square bilge earned her the title of “warehouse-type” ship and her iron masts and wire rigging enabled her to maintain full sail even in gale conditions. In 1908, with new sails, 29 crew, and 2800 tons of cargo in her hold, the FALLS OF HALLADALE left New York, bound for Melbourne and Sydney via the Cape of Good Hope. 102 days later, at 3 am on the 14th of November, under full sail and in calm seas, with a six knots breeze behind and a misleading fog along the coast, the great vessel rose upon an ocean swell and settled on top of a shelf of rock near Peterborough. There she stayed for nearly two months until the pounding seas and dynamiting by salvagers finally broke her back, and her remains disappeared back into deeper water. The iron-hulled, four-masted barque, the Falls of Halladale, was a bulk carrier of general cargo. She left New York in August 1908 on her way to Melbourne and Sydney. In her hold, along with 56,763 tiles of unusual beautiful green American slates (roofing tiles), 5,673 coils of barbed wire, 600 stoves, 500 sewing machines, 6500 gallons of oil, 14400 gallons of benzene, and many other manufactured items, were 117 cases of crockery and glassware. Three months later and close to her destination, a navigational error caused the Falls of Halladale to be wrecked on a reef off the Peterborough headland at 3 am on the morning of the 15th of November, 1908. The captain and 29 crew members all survived, but her valuable cargo was lost, despite two salvage attempts in 1908-09 and 1910. ABOUT THE ‘FALLS OF HALLADALE’ (1886 - 1908) Built: in1886 by Russell & Co., Greenock shipyards, River Clyde, Scotland, UK. The company was founded in 1870 (or 1873) as a partnership between Joseph Russell (1834-1917), Anderson Rodger and William Todd Lithgow. During the period 1882-92 Russell & Co., standardised designs, which sped up their building process so much that they were able to build 271 ships over that time. In 1886 they introduced a 3000-ton class of sailing vessel with auxiliary engines and brace halyard winches. In 1890 they broke the world output record. Owner: Falls Line, Wright, Breakenridge & Co, 111 Union Street, Glasgow, Scotland. Configuration: Four-masted sailing ship; iron-hulled barque; iron masts, wire rigging, fore & aft lifting bridges. Size: Length 83.87m x Breadth 12.6m x Depth 7.23m, Gross tonnage 2085 ton Wrecked: the night of 14th November 1908, Curdies Inlet, Peterborough south west Victoria Crew: 29 The Falls of Halladale was a four-masted sailing ship built in 1886 in Glasgow, Scotland, for the long-distance cargo trade and was mostly used for the Pacific grain trade. She was owned by Wright, Breakenridge & Co of Glasgow and was one of several Falls Line ships, all of which were named after waterfalls in Scotland. The lines flag was of red, blue and white vertical stripes. The Falls of Halladale had a sturdy construction built to carry maximum cargo and able to maintain full sail in heavy gales, one of the last of the ‘windjammers’ that sailed the Trade Route. She and her sister ship, the Falls of Garry, were the first ships in the world to include fore and aft lifting bridges. Previous to this, heavily loaded vessels could have heavy seas break along the full length of the deck, causing serious injury or even death to those on deck. The new, raised catwalk-type decking allowed the crew to move above the deck in stormy conditions. This idea is still used today on the most modern tankers and cargo vessels and has proved to be an important step forward in the safety of men at sea. On 4th August 1908, with new sails, 29 crew, and 2800 tons of cargo, the Falls of Halladale left New York, bound for Melbourne and Sydney via the Cape of Good Hope. The cargo on board was valued at £35,000 and included 56,763 tiles of American slate roofing tiles (roof slates), 5,673 coils of barbed wire, 600 stoves, 500 sewing machines, 6,500 gallons of oil, 14,400 gallons of benzene, plumbing iron, 117 cases of crockery and glassware and many other manufactured items. The Falls of Halladale had been at sail for 102 days when, at 3 am on the night of 14th November 1908, under full sail in calm seas with a six knots breeze behind and misleading fog along the coast, the great vessel rose upon an ocean swell and settled on top of a submerged reef near Peterborough on the south-west Victoria’s coast. The ship was jammed on the rocks and began filling with water. The crew launched the two lifeboats and all 29 crew landed safely on the beach over 4 miles away at the Bay of Islands. The postmistress at Peterborough, who kept a watch for vessels in distress, saw the stranding and sent out an alert to the local people. A rescue party went to the aid of the sailors and the Port Campbell rocket crew was dispatched, but the crew had all managed to reach shore safely by the time help arrived. The ship stayed in full sail on the rocky shelf for nearly two months, attracting hundreds of sightseers who watched her slowly disintegrate until the pounding seas and dynamiting by salvagers finally broke her back, and her remains disappeared back into deeper water. The valuable cargo was largely lost, despite two salvage attempts in 1908-09 and 1910. Further salvage operations were made from 1974-1986, during which time 22,000 slate tiles were recovered with the help of 14 oil drums to float them, plus personal artefacts, ship fittings, reams of paper and other items. The Court of Marine Inquiry in Melbourne ruled that the foundering of the ship was entirely due to Captain David Wood Thomson’s navigational error, not too technical failure of the Clyde-built ship. The shipwreck is a popular site for divers, about 300m offshore and in 3 – 15m of water. Some of the original cargo can be seen at the site, including pieces of roof slate and coils of barbed wire.The shipwreck of the FALLS OF HALLADALE is of state significance – Victorian Heritage Register No. S255. She was one of the last ships to sail the Trade Routes. She is one of the first vessels to have fore and aft lifting bridges. She is an example of the remains of an International Cargo Ship and also represents aspects of Victoria’s shipping industry. The wreck is protected as a Historic Shipwreck under the Commonwealth Historic Shipwrecks Act (1976).A large iron Rodger’s anchor recovered from the wreck of the FALLS OF HALLADALE. It has a rounded crown, curved arms and moulded flutes. Heavy duty iron stock with round eyes at either end, fitted over shank and fixed into position by a wedge-shaped metal locking pin. Shackle missing but severed securing bolt remaining in shank. The presence of an empty bolthole at the crown junction of shank and arms confirms Rodger’s type. Corroded from 66 years submersion in seawater but otherwise structure is sound.warrnambool, shipwreck coast, flagstaff hill, shipwrecked coast, flagstaff hill maritime village, flagstaff hill maritime museum, shipwreck artefact, maritime museum, falls of halladale, rodger’s anchor, peterborough reef, 1908 shipwreck, anchor, last days of sail, great clipper ships

Set of two 35mm Kodak white cardboard colour slide by Keith Kings of 24/12/1967 - .1 - St Kilda Junction, looking north along St Kilda Road, showing the nature of the diversion from the junction for Wellington St. .2 - Dandenong Road, showing the track diversion work for Dandenong Road/Queensway, Windsor.Keith Kings stamp and number "15-1" and "15-5"", with details of exposure. .1 - SW6 car on temporary track at St Kilda Junction looking north from turnout during freeway work .2 - Dandenong Road west from Hornsby St with section of straight track ready to replace curves onto new b.v.w. track to Chapel St - 907 coming off soon to be abandoned street track.trams, tramways, st kilda junction, trackwork, road works, dandenong road, queensway, tram 907

This tea caddy, an attractive item, was given to Margaret Fletcher (date of presentation unknown). A tea caddy in the 19th century was a valued object as tea was expensive and was bought in small quantities. The two side containers are for green and black tea and the middle one was for blending the tea mixtures. The caddy was lockable so that domestic workers etc could not have easy access to a valuable commodity. The local provenance of this object and the identity of Margaret Fletcher have not yet been established. She may be related to John Fletcher, the Warrnambool cordial maker or James Fletcher, the Warrnambool lawyer. This tea caddy is of great interest as an attractive artefact from the 19th century and as an example of a household item no longer in use. It is also of interest because it was given to Margaret Fletcher, possibly a local Warrnambool person. This is a polished wood container made in a casket style. The wood is believed to be Coramandel. The casket has curved sides and is on a base with four legs. The lid has a brass hinge and a gold lock with the key and the lock mechanism missing. Inside are three compartments, two with hinged lids with leather tops and zinc linings. The middle compartment has a glass container set in a wooden compartment. The inscription is on a brass plate inside the casket. ‘Presented to Margaret Fletcher as a Mark of Respect’. margaret fletcher, history of warrnambool

Telephones were mounted on the wall and were operated by turning a small handle situated in the middle of the phone. This connected the speaker to the switch board where they were 'put through' to the other end (speaker).Wall phones were used by State Electricity Commission of Victoria workers and their families on the Kiewa Hydro Electric Scheme. The SECV had a switchboard located at Mt Beauty. Also refer to article in "This Week" Newsletter 30th June 2023 and attached to KVHS 0050Black bakelite wall mounted telephone with handset connected by black spiral plastic cord. The round dial in the centre has a small handle with knob for turning. The base is silver steel with screws to attach it to the wall. The handset has a circular end with 4 small holes for the ear and the other end, the speaker end has 3 rings of small holes and a curved protective mouth piece to direct speech into the holes.On white circle in centre of dial: "To call turn handle and lift hand set. / When finished replace handset and turn handle" Handset embossed on inner side: 164 55wall mounted telephone; state electricity commission of victoria; kiewa hydro electric scheme; telecommunications; switchboard

These hair tongs were used to curl or wave hair. They have the name’ Marcel’ on them. In 1872 Francois Marcel Grateau invented a hairstyle called the ‘Marcel Wave’ where women’s hair styles had mostly deep waves rather than curls. The tongs that were held manually and heated and used at home to produce deep waves or curls become a commonplace item in a woman’s home in the late 19th and early 20th centuries. By the 1930s electric hair tongs were introduced but the non-electric ones continued to be used until the 1950s. These hair tongs belonged to a woman from England and would have been used in the 1930s or 40s. They are a good example of the type of household article used by women 70 or 80 years ago and will be useful for display.This is a scissors-like article with wooden handles and metal blades for waving or curling hair. One blade is heavily curved and the other is a solid round shape. The ends of the blades are tapered. The blades were heated over a stove and used manually to enclose part of a woman’s hair to produce waves or curls. The handles were originally polished black and are somewhat rubbed and the blades and other metal parts are a little rusty. ‘Marcel’ ‘12’ hair curling tongs, warrnambool

These scales come from the Nullawarre Post Office. Nullawarre is a small settlement 25 kilometres south east of Warrnambool. The area was settled in the late 1860s and 1870s and the first school was opened in 1878. The main agricultural pursuit in the Nullawarre district is dairying. The Nullawarre Post Office still operates in the General Store building. This set of scales is of interest as it is a memento of the equipment used in country Post Offices one hundred years ago or more. Scales such as these may still be in use but electronically-operated scales are more likely to be used today.This is a set of metal weighing scales with two trays, one oval in shape and one round, on a balancing mechanism. This mechanism has two ornamental upright metal pieces. The scales are affixed to a wooden base in a rectangular shape with the front edge shaped into two curves. The wooden base has three slots for holding the weights. There are six brass weights with this item. The metal is a little tarnished and the wooden base is stained. nullawarre, history of warrnambool

Detachable collars enclosed in a leather box such as this one were used in the 19th and early 20th centuries, particularly by men in the business and clerical professions. The collars were attached by studs or buttons to a shirt. The collars were removed prior to shirt washing the shirt. The leather box was most useful for travelling. Detachable collars could still be used today particularly by clergymen. Two are named E R Twomey.This box and collars are retained as an example of vintage men's wear. It will be useful for display.A brown leather cylindrical case with a strap and buckle. It has white thread stitching around the rim and upper edge of the lid, the slot for the buckle, the rim and lower edge of the base . Inside are four detachable white winged collars for wearing with a shirt. Each has three holes, one for a button and two for a stud or for buttons at the front, two wings and a curved slot at the back.They are made of very fine cotton and linen.002215.1 J.T. MADE IN ENGLAND ESPECIALLY FOR Buckley & Nunn Ltd. MELBOURNE 002215.2 A stamped lion, WELCH MARCETSON 7 CO. LTD. 4 THE ALATUS TRADE MARK DES M 9 M 520 1 3/4 x 1/2 T14 002215.3 MADE IN ENGLAND FOR BUCKLEY & NUNN MELBOURNE EXTRA QUALITY , A deer head with antlers in a pointed elipse E.R. THOMEY a red inverted drawn triangle two dots Lindum 2x 151/2 002215.4 MADE IN ENGLAND FOR BUCKLEY & NUNN MELBOURNE EXTRA QUALITY, A Deer head with antlers in a pointed elipse . T indecipherable . E.R.T.4 indecipherable. Lindum 2x15 002215.5 E.R. THOMEY Indecipherable Lindum 2x 15 ? warrnambool, detachable vintage collars, detachable men's shirt collars

See Dean Cat 4575PGold coloured metal case. The left and right sides are of black curved plastic. All the metal work has a dimpled appearance. The front cover has the enamelled badge of the Rats of Tobruk Association. The right side of the front cover has a oolumn of letters A-Z. There is a pointer to indicate which letter it is set to. On the bottom edge is a button which opens the lid. Inside are small pages with red lines.Nilsouvenir, mini address book

Herbert Edgar Hewston No 40 AIF. Refer Cat No 2759.2 for his service history. Part of the HEWSTON Collection WW1 & WW2..1) Badge, brass, Returned from Active Service, round with Crown on top, centre has Rising Sun depiction with AIF under. .2) Badge, Rising Sun lapel, blackened brass, 2 lugs on rear. .3) Badge, shoulder, Australia curved shape, blackened brass, 2 lugs on rear. Items relate to No 40 H E HEWSTON 3rd PNR BN AIF..1) “Issued by Dept of Defence, Returned from Active Service No 209185” .2) “Australian Commonwealth Military Forces”numismatics - medals /military, metalcraft- brassware, badges

This butter pat profiler may have been manufactured post 1967 (year post codes appeared in Australia) however the post code was only stamped on after it was machined. This type of butter mould was used by rural families to fashion home/farm made butter. This period was in most rural regions a time of self sufficiency where any domestic type implement which could be fashioned by the family would be crafted with skill. Shopping for goods required catalogues from stores located in major rural towns and cities and involved lengthy waiting times. Travelling to and from these specialised stores was not pleasant due to the relatively poor quality of the roads and the lengthy times taken. The small general stores in the Kiewa Valley could not cater for all the needs of the valley. The 1960's was a time when facilities especially goods and services started to improve drastically. The S.E.C. of Victoria with its Kiewa Hydro Electricity Scheme provided not only an improvement of facilities in the valley but also a increase in the population. This increase resulted in a greater demand for local produce.This item is one of many domestic food processing implements used by Kiewa Valley households in the mid 1900s, whether on the farm or in the small towns and hamlets. Self sufficiency was the key to survival during these early times. Where ever possible supplies from within the valley were preferred to that brought in by travelling salesmen or traders. This butter mould and butter pat was commonly used to fashion "home" made butter throughout the valley and in some cases supplied to "outside" regional towns. Although this method of production was phased out by better access to goods from nearby cities the revival of the good organic home grown produce in the 1980s saw a greater demand of this type of farm based produce.This butter pat is one of two,see KVHS 0071 (B). It has been crafted from wood. One side has grooves running from the handle to the square shaped bottom. These grooves would stop the wet butter from clinging to the pat. The top side of the pat has been bevelled on both sides and the bottom edge. The hand grip is flat and curved to allow for a comfortable hold.domestic food preparation, wooden butter pat, butter mould circular, dairy industry, butter

This collection of photos depicts the members of the Learmonth A.N.A. Branch No.75,in 1912.It was presented to C.Medwell Esq.(Secretary),by his fellow members in appreciation of services to the branch as Secretary.The members are C.Hamilton, B.H.Louden, J.Ritchie, W.R.Sara, M.Baird, A.Patterson, A.E.Medwell, R.E.Sara - Assistant Secretary, R.Dowler, J.R.Creelman, J.Leys - commmitee, J.Doolan - President, J.Whately, T.Whately, M.Donovan - commitee, T.E.Connelly - commitee, W.McCubbin, D.Doyle, E.C.Kinnersley, M.Ryan - Trustee, P.Ryan - Treasurer, M.Casey - Secretary, J.Medwell - Trustee, Dr C.A.Courtney - Medical Officer, J.Tonks, J.C.Robertson, J.Yates, J.Curran, P.Casey - commitee,R.L.Medwell, D.Baird, A.E.Stewart, A.Whately - Vice President, H.A.Page - commitee, W.H.Lang, H.Lang, W.D.Sara - Auditor, W.T.Hamilton - Auditor, R.Jarrett, A.Medwell, F.Kinnersley, W.W.Walker, J.Barnes, J.Parker. Original photo showing members belonging to the Learmonth A.N.A. Branch no.75 in 1912Black and white photos of A.N.A.members in 1912,set in wide dark brown frame with carved decorative outer edge,the mount is lighter brown wood. The main photo of C.Medwell Esq.Secretary, is surrounded by a decorative gold trim and between each photo there are decorative markings in white.The Inscriptions are white edged in black.The photos vary in shape,oval, rectangular,rectangular with curved top and rectangular with shaped cut top. LEARMONTH A.N.A. BRANCH N0.75. PRESENTED TO C. MEDWELL Esq. BY HIS FELLOWS MEMBERS AS A MARK OF ESTEEM & APPRECIATION OF VALUABLE SERVICES RENDERED TO THE BRANCH AS SECRETARY. LEARMONTH 1912. Richards & Co. Photos.learmonth ana branch no 75, c medwell 1912

This chair is one of a set of four chairs from the St. Nicholas Seamen’s Church, 139 Nelson Place, Williamstown, Victoria, during religious services there. The Church was operated by the Mission to Seamen organisation. * for more detailed history please see our Registration Number 658, Set of chairs This set of chairs is significant historically for its origin in the St Nicholas Mission to Seamen's Church in Williamstown, established in 1857 to cater for the physical, social, and spiritual needs of seafarers. It originated in Bristol, England when a Seamen's Mission was formed in 1837. The set of chairs is historically significant for its connection to the Ladies Lightkeepers’ Auxiliary, an organisation of women, formed to support seafarers. The connection of this set of chairs to the Mission to Seamen and to the Ladies Lightkeepers’ Auxiliary highlights the strong community awareness of the life of people at sea, their dangers and hardships, and their need for physical, financial, spiritual and moral support. Chair: Australian Colonial rail back dining chair. Chair is one of a set of four (4) cedar wood chairs. Each chair has a rounded rail back, flat cross rail, flat solid wood seat, curved back legs and colonial turned front legs. Mid-brown colour, veneer finish. The set of chairs is part of the St Nicholas Seamen's Church Williamstown Collection. flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, religion, religious service, sailors rest, sailors’ church, bethel sailors’ church, bethel floating church, ladies harbour light guild, lightkeepers’ auxiliary, missions to seamen victoria, mission to seafarers, flying angel’s club, ann street williamstown, st nicholas seaman’s church williamstown, st nicholas mission to seamen church williamstown, mission to seamen williamstown, st nicholas seamen’s church flagstaff hill, 139 nelson place williamstown, church furniture, religious furniture, religious worship, anglican church, chair, dining chair, kitchen chair, domestic furniture, colonial chair, australian colonial period, cedar chair

This chair is one of a set of four chairs from the St. Nicholas Seamen’s Church, 139 Nelson Place, Williamstown, Victoria, during religious services there. The Church was operated by the Mission to Seamen organisation. * for more detailed history please see our Registration Number 658, Set of chairs This set of chairs is significant historically for its origin in the St Nicholas Mission to Seamen's Church in Williamstown, established in 1857 to cater for the physical, social, and spiritual needs of seafarers. It originated in Bristol, England when a Seamen's Mission was formed in 1837. The set of chairs is historically significant for its connection to the Ladies Lightkeepers’ Auxiliary, an organisation of women, formed to support seafarers. The connection of this set of chairs to the Mission to Seamen and to the Ladies Lightkeepers’ Auxiliary highlights the strong community awareness of the life of people at sea, their dangers and hardships, and their need for physical, financial, spiritual and moral support. Chair: Australian Colonial rail back dining chair. Chair is one of a set of four (4) cedar wood chairs. Each chair has a rounded rail back, flat cross rail, flat solid wood seat, curved back legs and colonial turned front legs. Mid-brown colour, veneer finish. The set of chairs is part of the St Nicholas Seamen's Church Williamstown Collection. flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, religion, religious service, sailors rest, sailors’ church, bethel sailors’ church, bethel floating church, ladies harbour light guild, lightkeepers’ auxiliary, missions to seamen victoria, mission to seafarers, flying angel’s club, ann street williamstown, st nicholas seaman’s church williamstown, st nicholas mission to seamen church williamstown, mission to seamen williamstown, st nicholas seamen’s church flagstaff hill, 139 nelson place williamstown, church furniture, religious furniture, religious worship, anglican church, chair, dining chair, kitchen chair, domestic furniture, colonial chair, australian colonial period, cedar chair

This chair is one of a set of four chairs from the St. Nicholas Seamen’s Church, 139 Nelson Place, Williamstown, Victoria, during religious services there. The Church was operated by the Mission to Seamen organisation. * for more detailed history please see our Registration Number 658, Set of chairs This set of chairs is significant historically for its origin in the St Nicholas Mission to Seamen's Church in Williamstown, established in 1857 to cater for the physical, social, and spiritual needs of seafarers. It originated in Bristol, England when a Seamen's Mission was formed in 1837. The set of chairs is historically significant for its connection to the Ladies Lightkeepers’ Auxiliary, an organisation of women, formed to support seafarers. The connection of this set of chairs to the Mission to Seamen and to the Ladies Lightkeepers’ Auxiliary highlights the strong community awareness of the life of people at sea, their dangers and hardships, and their need for physical, financial, spiritual and moral support. Chair: Australian Colonial rail back dining chair. Chair is one of a set of four (4) cedar wood chairs. Each chair has a rounded rail back, flat cross rail, flat solid wood seat, curved back legs and colonial turned front legs. Mid-brown colour, veneer finish. The set of chairs is part of the St Nicholas Seamen's Church Williamstown Collection. flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, religion, religious service, sailors rest, sailors’ church, bethel sailors’ church, bethel floating church, ladies harbour light guild, lightkeepers’ auxiliary, missions to seamen victoria, mission to seafarers, flying angel’s club, ann street williamstown, st nicholas seaman’s church williamstown, st nicholas mission to seamen church williamstown, mission to seamen williamstown, st nicholas seamen’s church flagstaff hill, 139 nelson place williamstown, church furniture, religious furniture, religious worship, anglican church, chair, dining chair, kitchen chair, domestic furniture, colonial chair, australian colonial period, cedar chair

This chair is one of a set of four chairs from the St. Nicholas Seamen’s Church, 139 Nelson Place, Williamstown, Victoria, during religious services there. The Church was operated by the Mission to Seamen organisation. * for more detailed history please see our Registration Number 658, Set of chairs This set of chairs is significant historically for its origin in the St Nicholas Mission to Seamen's Church in Williamstown, established in 1857 to cater for the physical, social, and spiritual needs of seafarers. It originated in Bristol, England when a Seamen's Mission was formed in 1837. The set of chairs is historically significant for its connection to the Ladies Lightkeepers’ Auxiliary, an organisation of women, formed to support seafarers. The connection of this set of chairs to the Mission to Seamen and to the Ladies Lightkeepers’ Auxiliary highlights the strong community awareness of the life of people at sea, their dangers and hardships, and their need for physical, financial, spiritual and moral support. Chair: Australian Colonial rail back dining chair. Chair is one of a set of four (4) cedar wood chairs. Each chair has a rounded rail back, flat cross rail, flat solid wood seat, curved back legs and colonial turned front legs. Mid-brown colour, veneer finish. The set of chairs is part of the St Nicholas Seamen's Church Williamstown Collection. flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, religion, religious service, sailors rest, sailors’ church, bethel sailors’ church, bethel floating church, ladies harbour light guild, lightkeepers’ auxiliary, missions to seamen victoria, mission to seafarers, flying angel’s club, ann street williamstown, st nicholas seaman’s church williamstown, st nicholas mission to seamen church williamstown, mission to seamen williamstown, st nicholas seamen’s church flagstaff hill, 139 nelson place williamstown, church furniture, religious furniture, religious worship, anglican church, chair, dining chair, kitchen chair, domestic furniture, colonial chair, australian colonial period, cedar chair

Brass door roller from a former Melbourne cable car trailer - numbered 2 222 - probably No. 2 end of trailer No. 222. Consists of a large cast section for attachment to the top of the door, roller wheel and axle. Cable trams commenced in 1885 and by 1891 there were 350 sets. (see reference) See p79 of "Mind the Curve", John D.Keating re number of tram built by 1891.melbourne, cable trams, door roller, tramcar component

John McLaren Dimmick was the son of Cr William (Roy) Dimmick (1888-1947) and his wife, Myrtle Elvira (nee Monie - 1888-1976). He had brothers Samuel Guy McLaren Dimmick and Frank McLaren Dimmick.Black and white photo of a boy identified as John Dimmick with his prize-winning decorated bicycle on one of the curved paths in the Surrey Gardens. He is dressed in a shirt, tie and jumper. He is holding a bicycle which is liberally decorated and with flags on the handle-bars. A 1st prize certificate is attached to the handlebars. The WW1 war memorial can be seen in the background and also Dr Box's home, 'Montalto (demolished). SH763 on rear in pencil.empire day celebrations, surrey gardens, children, festivals and celebrations, john dimmick, john mclaren dimmick

A meat grinder or mincer was used for mincing or fine chopping of raw or cooked meat, fish, vegetables or similar food. It replaced tools like a mincing knife.A small vintage cast iron mincer with a wooden handle attached to the long cast iron handle. It can be screwed to a table or bench, secured tightly by a two pronged claws. It has a white enamel coated funnel at the top for the meat to be pushed into the mechanism which when the handle is turned operates the inner mechanism which forces the minced meat out through a side opening. The cast iron handle is curved.'Loveload London 1'domestic objects, kitchen equipment, cooking equipment, meat grinders, meat mincers

A meat grinder or mincer was used for mincing or fine chopping of raw or cooked meat, fish, vegetables or similar food. It replaced tools like a mincing knife.A cast iron mincer with a wooden handle attached to the long cast iron handle. It can be screwed to a table or bench, secured tightly by a two pronged claws. It has a funnel at the top for the meat to be pushed into the mechanism which when the handle is turned operates the inner mechanism which forces the minced meat out through a side opening. The cast iron handle is curved. There are three mincing attachments tied with string.'UNIVERSAL' is stamped on the top of the mincer. Stamped on the front side of the handle - ' L.P. F&C. NEW BRITAIN. CONN.U.S.A.' On the inside of the cast iron handle is stamped - 'PATENT 10.2.1897. PATENT.MAY 15.1900. 4.18. 1890...... and several other numbers which are difficult to decipher.domestic objects, kitchen equipment, cooking equipment, meat grinders, meat mincers

Book - black covers - 4 sections sewn - 124 pages lined - titled "Lengths of Lines and Curves". Has an index. Gives details of junction layouts, distances, hand drawing layouts, route and track miles, tables of actual distances, average distance and figure on which mileage is worked. In the rear of the book are some hand written calculation notes. Not all pages imaged, just those with a diagram.On top of the cover of one copy in ink "pages 1, 4, 14,17, 23"trams, tramways, trackwork, mmtb, mileages

Poster - of a page of the April 2003 issue of Transit Australia, giving an elevation and floor plan of "The Oporto Eurotram" that was demonstrated in Melbourne during January and March 2003. Has an outline dimension drawing of the tram and the Bombardier builder and logo, with some details about it operations and limitations about curves. Has been prepared using two sheets of A3 paper. See Reg Item 4754 for photos by Colin Rough.trams, tramways, combino, citadis, eurotram, melbourne, docklands, aeta, tram 18

Buninyong Bivium (2016) by Cliff Burtt engages with the geography and history of the Buninyong region in both pre and post settlement. The town of Buninyong is dominated by the profiles of Mt Helen and the extinct volcano Mt. Buninyong. Traditional land of the Wadawurrung people, today the area remains a significant site for the culture of indigenous people and their connection to the land. The profile of this sculpture is based on topographical mapping of the area, depicting sections of the landscape. The gaps between the elements of the work can be viewed as representations of the shafts sunk into the earth by the early gold miners and compound curves on the upper surfaces are mirroring the topography of the area, while cut-aways in the sides are suggestive of rock strata.The artwork is of aesthetic and social significance to the people of BallaratCorten steel sculpture made of five unique sculptural pieces secured to at concreate base at pavement levelbuninyong, cliff burtt, sculpture, public art, mining, ballarat

The Fashion & Design collection of the Kew Historical Society includes examples of women’s, men’s, children’s and infants’ clothing from the 18th, 19th and 20th centuries. Items in the collection were largely produced for, or purchased by women in Melbourne, and includes examples of outerwear, protective wear, nightwear, underwear and costume accessories.The V&A's history of fashion describes 1930s dresses as characterised by '... a slinky femininity... Parisian couturiers introduced the bias-cut into their designs, which caused the fabric to skim over the body's curves. Long, simple and clinging evening gowns, made of satin were popular. Often the dresses had low scooping backs'.Full length floral crepe evening dress with squared neck and short puffed sleeves.australian fashion - 1930s, women's clothing, evening dresses

Rose Series postcard No. P 1040, titled "Flinders Street Railway Station, Melbourne" showing the entrance to the station, many motor cars, some with black-out headlight covers, a MMTB Leyland bus, and a W2 class tram either 288 or 388 (Kew Depot cars at the time.) with the destination of Spencer St. This would have to be one of the first W2 class cars to have the metal gutter replaced by a storm/drip rail. There is an advertising board on the railway station verandah, advertising Liberty Loans. You can just make out the tram overhead for the curve from Swanston Street into Flinders Street.Yields information about Flinders Street and railway station in the early 1940s.Postcard - printed real photograph with Rose Stereograph Co. name on the rear.tramways, trams, flinders st, flinders st station, w2 class, buses, mmtb buses, world war ii

This tool is part of a large collection of vintage tools and they are believed to have belonged to a Warrnambool businessman, Henry Phillips. English-born carpenter, Henry Phillips (1821-1896), with his wife, Elizabeth, came to Australia in 1849 and lived in Port Fairy for some time. In 1865 he formed a partnership with Christopher Beattie and established the undertaking firm of Beattie and Phillips. The funeral business continued on after the deaths of the two founders and lasted until the year 2000. In Warrnambool Henry Phillips was involved with the management of the Mechanics’ Institute.This tool is of interest as an example of a vintage tool and also as a memento of the 19th century Warrnambool businessman, Henry Phillips.This is a large rectangular-shaped wooden plane tool. It has a curved wooden handle with a flattened top and this is inserted into the top of the body of the tool. The middle section of the top of the tool had been gouged out and a metal blade inserted at an angle and this blade partly protrudes at the base to make a planing tool. The metal blade is held in place by a covering piece of wood and a metal screw holds both the inserted wood and the blade in place.vintage tools, henry phillips,, history of warrnambool

This is a teacher's desk which came from Woodford State School. The school began in 1854 in a private dwelling with a new building constructed in 1874. The school still operates today.This is a very fine example of an early 20th century school teacher's desk. As it comes from one of the earliest schools in the district, it is of considerable significance.This is a wooden desk, now varnished, with a lift up, slanted lid with brass hinges and a brass key hole. On the top right hand side is a brass insert with a porcelain ink well. The desk has four turned legs with end struts. The desk lid may be made of pine but the rest of the desk seems to be made of a different wood. There are signs of old borer on the left hand front and the curved part on that side is missing.woodford state school

Metal RAAF Point Cook crest mounted on a small dark red coloured plaque. The plaque has a mounting slot on the back and foward sloping curved sides meeting at a lower point. The circular RAAF crest has a jeweled crown at the top, black lettering at the bottom, and gold lettering on a circular blue enamel background surrounding a brown coloured line drawing of an eagle flying over water with the sun in the background.Point Cook Royal Australian Air Force First And Foremostraaf, point cook, crest, metal, plaque