Showing 10660 items
matching water-supply
-
Bendigo Historical Society Inc.
Document - CONNELLY, TATCHELL, DUNLOP COLLECTION: RECEIVAL OF LETTER CARDS
Two printed cards acknowledging the receival of a letter. One is from Thos F Morkham, Secretary for Lands, dated 28 Sept 1898 and addressed to Messrs Connelly Tatchell & Dunlop, Williamson St, Bendigo and the other from C W Langtree, Secretary for Mines and Water Supply, dated 30/3/87, and addressed to ? J Connelly Esq, Albion Chambers, Sandhurst.business, legal, connelly & tatchell, connelly & tatchell collection: receival of letter cards, c w langtree, ? j connelly esq, b a wallace, thos f morkham, connelly tatchell & dunlop -
Seaworks Maritime Museum
Diagram
Cross section of wharves and steel framed sheds built along the Yarra river between the 1920s and 1960s. The South Melbourne side of the Yarra River is reclaimed swamp land. Without a solid foundation for the construction of the wharves and transit sheds, extended piles were sunk into the mud to support the wharf and shed structures. An example of this design may be found at 5 South Wharf which was built in the 1930s. The transit sheds gave shelter for cargo while waiting to be loaded onto a ship or to be collected by truck after being unloaded from a ship. The transit shed became surplus to requirements with the introduction of containers.Wooden diagram of a transit shed featuring a shed sitting atop mud with some water. It shows the splices sitting in the mud to support the shed. "Steel Frames Transit Shed/ 15 South Wharf/ Model of Typical wharf construction/ of 1940- made for the opening of/ the "new" 15 South wharf shed (1944),/ Note the deep piles and elevated/ rear of the shed to allow for the truck/ trays./ This shed feature disappeared/ from port construction with the/ coming of the container era/ reinforced wharf apron/ 3 ton travelling crane/ reinforced concrete shed floor/ concrete road/ water level/ concrete pile cap/ cradled piles/ timber pile splices/ mud/ mild steel pile splices/ 110 ft pile" "On loan from Port of Melbourne Authority" -
Bendigo Military Museum
Equipment - WEBBING KIT, 1911; Post 1911
The 1908 pattern was used during WWI, made from woven cotton & water proofed. The kit is used for school groups.Webbing kit complete including 1908 pattern webbing, gas mask haversack, personnel items, rations. Refer attached sheet. .1) Waist belt with brass buckles & keepers. .2) Braces x 2, connects to waist belt & large pack. .3) Bayonet. .4) Bayonet carrier. .5) Bayonet scabbard. .6) Entrenching tool carrier [fits to .5)]. .7) Entrenching tool handle, wood & metal [fits to .6)]. .8) Entrenching tool, metal, combination shovel & pick. .9) Entrenching tool carrier [fits inside .8)]. .10) Cartridge carriers x 2, 1 left hand, 1 right hand. .11) Water bottle, metal, blue colour. .12) Water bottle cover, khaki wool. .13) Water bottle carrier. .14) Pack, large. .15) Great coat, wool, [inside .14)]. .16) Helmet, steel with inside liner & chin strap. .17) Mess tin carrier, replica. .18) Haversack, side pack. .19) Carry all, white cotton, for personnel hygiene items [inside .18)]. .20) Razor, cut throat [inside .19)]. .21) Comb [inside .19)]. .22) Toothbrush [inside .19)]. .23) Shaving brush [inside .19)]. .24) Laces, leather, not original, [inside .19)]. .25) Soap [inside .19)]. .26) Tin bully beef x 2, replicas, [inside .18)]. .27) Tin stew, replica, [inside .18)]. .28) Pair socks, khaki wool, not original, [inside .18)]. .29) Field dressing, WWII issue, [inside .18)]. .30) Towel, brown colour, not original, [inside .18)]. .31) Gas mask carrier bag & straps. (Cowley) .32) Water bottle, metal, blue colour, [inside .31)].Items 1 - 13, there are numerous markings all stamped on from, “A.A.O.D”, “L”, “R”, “S”, “M.E.C.O”, “49th INF”, Years examples, “8.12”, “1.13”, “1911”military history - equipment / army, medicine-first aid, personal effects - containers, toilet requisites - shaving -
Lara RSL Sub Branch
Painting Lara RSL, March 2018
Painting of Lara RSL in 2018. Building erected in June 1864. Used by the Shire of Corio from 1874 to 1937. The Lara RSL sub branch had their first official meeting in the building on 11/4/1949.Water Coloured Painting in Wooden FrameRear of Painting - Donated by Karen and Rob Dick. Painted by Karen Dick March 2018lara rsl buiding watercolour karen dick 2018 -
Federation University Historical Collection
Geological specimen - Rocks, Petrified Wood
From the Ballarat School of Mines.Petrified wood with some water polish.rocks, geology, petrified wood -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Tools, small brass water tap, c1900
This Water tap is typical of those used by early settlers in Moorabbin Shire c1900 Water tap, small brassearly settlers, pioneers, market gardeners, moorabbin, bentleigh, brighton, cheltenham, tools, metal workers, plumbers -
Running Rabbits Military Museum operated by the Upwey Belgrave RSL Sub Branch
Water Bottle
Water bottle, no webbing, Aluminium. Chineseequipment, vietnam, army -
Running Rabbits Military Museum operated by the Upwey Belgrave RSL Sub Branch
Water Bottle
Australian water bottle attached to EQ146equipment, ww2, army -
Running Rabbits Military Museum operated by the Upwey Belgrave RSL Sub Branch
Water Bottle
Water Bottle comprising pannikin and holderequipment, 1st gulf war, army -
Running Rabbits Military Museum operated by the Upwey Belgrave RSL Sub Branch
Water Sterilization Kit
Sterilizling outfit for use with Water Bottlesequipment -
Running Rabbits Military Museum operated by the Upwey Belgrave RSL Sub Branch
Water Bottle Webbing
Water bottle webbing pattern 37equipment, ww2+, army -
Running Rabbits Military Museum operated by the Upwey Belgrave RSL Sub Branch
Water Bottle
Water bottle blue enamel and strappingequipment, ww1, army -
Bendigo Historical Society Inc.
Slide - BENDIGO VIEWS, Apr 1960
Slide. Bendigo Views. Water and trees.slide, bendigo, bendigo views, bendigo views -
Tatura Irrigation & Wartime Camps Museum
Photograph - copy
Borrowed for copying.Rushworth's first water pumping station. -
Stawell Historical Society Inc
Memorabilia - Realia, 1910-1930
Bedroom Water Jug . Leyshon Familystawell -
Stawell Historical Society Inc
Memorabilia - Realia, c1940's
I. Richards – Aerated Water Stawellstawell -
Clunes Museum
Photograph
PHOTOCOPY OF CLUNES TOURELLO WATER SHED.local history, photography, photographs, water supply -
Stawell Historical Society Inc
Slide, Ian McCann, Lake Bellfield
Lake Bellfield With Water after completionlake bellfield -
Stawell Historical Society Inc
Functional object - Bottle
Hemley & Sons Aerated Water Bottlestawell -
Stawell Historical Society Inc
Photograph, Stawell Gold Mine
Mine at Dusk or Dawn across watergold mining -
Ballarat Heritage Services
Photograph - Colour, Clare Gervasoni, Wombat Botanical Gardens, Daylesford, 2019, 23/04/2019
Water stressed Rhododendrons in the Wombat Gardens. wombat botanical gardens, daylesford botanical gardens, daylesford, trees -
Ringwood RSL Sub-Branch
Uniform, WW2 vintage
Water repellant light canvas rectangleARP Warden printed black on white -
Ringwood RSL Sub-Branch
Equipment, WW1
WW1 leather water bottle holder -
Running Rabbits Military Museum operated by the Upwey Belgrave RSL Sub Branch
Webbing
37 Pattern water bottle holderequipment, ww1, army -
Queenscliffe Maritime Museum
Painting - Water colour painting of The Lord Warden, The Lord Warden, 1917
Arthur V Gregory b.1867, d.1957 worked from studio at 326 Albert Road South Melbourne established by his father G F Gregory in 1852Water colour painting in wooden frameThe Lord Warden passing Cape Otway 1870 A.V. Gregory-17-lord warden, a.v. gregory, water colour -
Vision Australia
Painting - Artwork, Lin Ditchfield, Sydney Industrial Blind Institution in William Street, 1971
Watercolour by Lin Ditchfield of the Royal Blind Society of New South Wales (formerly the Sydney Industrial Blind Institution) in William Street, Sydney. Built in 1880, the Edmund Blacket designed building was eventually sold in 1971. Located on the corner of William Street and Boomerang Place, the site was keenly sought by developers as the city landscape transformed into high rise office builidings, as evidenced in the background of this painting.Painted by Lin Ditchfield1 water colour in beige frameLin Ditchfield 1971royal blind society of new south wales, lin ditchfield -
University of Melbourne, Burnley Campus Archives
Photograph - Black and white print, 906/8, c. 1949
Seed raising bed being watered.seed raising beds, watering, e. m. gibson collection -
Lilydale RSL Sub Branch
Water Bottle and Carrier
Used by George Styles 3 RAR 1953 in Korea and later in Vietnam. George Styles is a long time Mooroolbark resident1903 pattern water bottle and carrier. George Styles 3RAR -
City of Ballarat
Artwork, other - Public Artwork, Petersen Fountain, 1922
This fountain was created as the result of a bequest from Ballarat businessman Carsten Heinrich Petersen who was killed at the age of eighty-five years when crossing Sturt Street opposite the Base Hospital. On the other side of the street were three brick shops which he owned. The fountain has four bronze frog water spouts beneath four marble stork spouts. Above the top bowl is another stork in bronze with its wings spread and water issues from its outstretched beak. The Petersen Fountain has been restored many times, first in 1977 with funds provided by the Rotary Club of Ballarat South. In 1989 further restoration works were completed to replace bronze frogs and a brass and copper stork made by Ballarat craftsman Lloyd Lusk to replace the original bird which was stolen and never recovered. The second stork was also stolen on the 3rd of August 1983 and further repairs of the fountain were carried out in 1993. The artwork is of historical and aesthetic significance to the people of Ballarat. The Petersen Fountain is carved marble, features storks carved into its base and the faces of cherubs in the bowl. It has a copper crane perched at the top and bronze frogs surrounding that spray water. The fountain stands on a granite base. PRESENTED/ BY/ C.H. PETERSEN/ BORN IN DENMARK 2nd MARCH 1836/ DIED BALLAARAT 9 FEBRUARY 1922petersen fountain -
Flagstaff Hill Maritime Museum and Village
Domestic object - Plate, Johnson Bros
The Process of Making Pottery Decorating, Firing, Glazing, Making, Technical There is a rhythm and flow to clay. It can’t be done all at once! Even the making process! It can take weeks to get everything done, especially if you can only work on your pottery once a week! Even though we have three hour classes, it’s often just not enough time! Here is an overview of some of the processes so you have a bit more grasp on some of the technical stuff! Step One – Design There are SO many ideas out there for making stuff in clay! From delicate porcelain jewellery, through to heavy sculptural work and everything in between. Deciding your direction is sometimes not that easy – when you first start, try everything, you will naturally gravitate to the style that you enjoy! The options and variations are endless and can get a wee bit overwhelming too! Check in with me before you start to ensure your ideas will work, what order you might do things, how you could achieve the look you are seeking and any other technical data required! Step Two – Making Clay is thixotropic. This means that as you work with it, the clay first gets sloppier and wetter, before is begins to dry in the atmosphere. For most things, you simply can’t do all parts of the project at once. An example of work order might look like: Get last weeks work out from the shelves Prepare clay for today’s work – roll your clay, prepare balls for throwing, make the first stage of a pinch pot) Clean up last week’s work and put it on the shelf for bisque firing Check that you have any glazing to do – and do enough of it that you will have time to finish your main project Do the next step of your next project – there might be a further step that can’t be complete immediately, in that case, wrap your work well and put onto the shelves. Letting your work rest for a while can really help keep your work clean and professional looking. Many things require bagging under plastic to keep it ready for work the next week – put your name on the outside of the bag so you can find your work easily. We have stickers and markers. Consider how you want to decorate your work – coloured slip can be applied at a fairly wet stage (remembering that it will make your work even wetter!). Trying to apply slip to dry clay won’t work! If you want to do sgraffito – you will need to keep the work leather hard (a state of dryness where you can still work the clay with a little effort and a little water and care). Step Three – Drying Most of the time your work can go into the rack uncovered to let it dry out for the following week. If you want to continue forming or shaping you will need to double bag your work – put your work on a suitable sized bat and put the bat in a bag so the base of the bag is under the bat, then put another bag over the top of the work and tuck the top of the bag under the bat. If you want to trim (or turn) your thrown work the following week, it should also be double bagged. If your work is large, delicate, or of uneven thicknesses, you should lightly cover your work for drying. When considering the drying process, bare in mind the weather, humidity and wind! The hotter and dryer, the faster things dry and work can dry unevenly in the shelves – this can lead to cracking – another time to lightly cover your work for drying. Step Four – Trimming and Cleaning Up Your work is dry! It is called greenware now and it is at it’s most fragile! Handle everything with two hands. I often refer to soft hands – keep everything gentle and with your fingers spread as much as possible. Try to not pick up things like plates too much, and always with both hands! Before your work can be bisque fired it should be “cleaned up”. You work won’t go into the kiln if it has sharp edges – when glazed, sharp edges turn into razor blades! Use a piece of fly wire to rub the work all over – this will scratch a little so be light handed. Use a knife or metal kidney to scrape any areas that require a bit more dynamic treatment than the fly wire offers! Finally, a very light wipe over with a slightly damp sponge can help soften and soothe all of your edges and dags! Trimming thrown work: If you are planning to trim (or turn) your thrown work (and you should be), make sure you bag it well – your work should be leather hard to almost dry for easiest trimming. Use this step to finish the work completely – use a metal kidney to polish the surface, or a slightly damp sponge to give a freshly thrown look. Wipe the sponge around the rim after trimming, and check the inside of the pot for dags! Trimming slip cast work: Usually I will trim the rims of your work on the wheel the following day to make that stage easier, however you will still need to check your work for lumps and bumps. Last but not least – check that your name is still clearly on the bottom of your work. Step Five – Bisque Firing When the work is completely dry it can go into the bisque kiln. The bisque kiln is fired to 1000°C. This process burns off the water in the clay as well as some of the chemically bound water. The structure of the clay is not altered that much at this temperature. Inside the bisque kiln, the work is stacked a little, small bowl inside a larger bowl and onto a heavy plate. Smaller items like decorations or drink coasters might get stacked several high. Consideration is paid to the weight of the stack and shape of the work. A bisque kiln can fire about one and a half times the amount of work that the glaze kiln can fire. The firing takes about 10 hours to complete the cycle and about two days to cool down. Once it has been emptied the work is placed in the glaze room ready for you to decorate! Step Six – Glazing Decorating your work with colour can be a lot of fun – and time consuming! There are three main options for surface treatment at this stage: Oxide Washes Underglazes Glazes Washes and underglazes do not “glaze” the work – It will still need a layer of glaze to fully seal the clay (washes don’t need glaze on surfaces not designed for food or liquid as they can gloss up a little on their own). Underglazes are stable colourants that turn out pretty much how they look in the jar. They can be mixed with each other to form other colours and can be used like water colours to paint onto your work. Mostly they should have a clear glaze on top to seal them. Oxides are a different species – the pink oxide (cobalt) wash turns out bright blue for instance. They don’t always need a glaze on top, and some glazes can change the colour of the wash! The glazes need no other “glaze” on top! Be careful of unknown glaze interactions – you can put any combination of glaze in a bowl or on a plate, but only a single glaze on the outside of any vertical surface! Glazes are a chemical reaction under heat. We don’t know the exact chemicals in the Mayco glazes we use. I can guess by the way they interact with each other, however, on the whole, you need to test every idea you have, and not run the test on a vertical surface! Simply put, glaze is a layer of glass like substance that bonds with the clay underneath. Clay is made of silica, alumina and water. Glaze is made of mostly silica. Silica has a melting point of 1700°C and we fire to 1240°C. The silica requires a “flux” to help it melt at the lower temperature. Fluxes can be all sorts of chemicals – a common one is calcium – calcium has a melting point of 2500°C, however, together they both melt at a much lower temperature! Colourants are metal oxides like cobalt (blue), chrome (green through black), copper (green, blue, even red!), manganese (black, purple and pink) iron (red brown), etc. Different chemicals in the glaze can have dramatic effects. for example, barium carbonate (which we don’t use) turns manganese bright pink! Other elements can turn manganese dioxide brown, blue, purple and reddish brown. Manganese dioxide is a flux in and of itself as well. So, glazes that get their black and purple colours, often interact with other glazes and RUN! Our mirror black is a good example – it mixes really well with many glazes because it fluxes them – causes them to melt faster. It will also bring out many beautiful colours in the glazes because it’s black colouring most definitely comes from manganese dioxide! Glaze chemistry is a whole subject on it’s own! We use commercial Mayco glazes on purpose – for their huge range of colour possibilities, stability, cool interactions, artistic freedom with the ability to easily brush the glazes on and ease of use. We currently have almost 50 glazes on hand! A major project is to test the interactions of all glazes with each other. That is 2,500 test tiles!!!! I’m going to make the wall behind the wheels the feature wall of pretty colours! Step Seven – Glaze (Gloss or sometimes called “Glost”) Firing Most of the time this is the final stage of making your creation (but not always!) The glaze kiln goes to 1240°C. This is called cone 6, or midrange. It is the low end of stoneware temperatures. Stoneware clays and glazes are typically fired at cone 8 – 10, that is 1260 – 1290°C. The energy requirement to go from 1240°C to 1280°C is almost a 30% more! Our clay is formulated to vitrify (mature, turn “glass-like”) at 1240°, as are our glazes. A glaze kiln take around 12 hours to reach temperature and two to three days to cool down. Sometimes a third firing process is required – this is for decoration that is added to work after the glaze firing. For example – adding precious metals and lustres. this firing temperature is usually around 600 – 800°C depending upon the techniques being used. There are many students interested in gold and silver trims – we will be doing this third type of firing soon! After firing your work will be in the student finished work shelves. Remember to pay for it before you head out the door! There is a small extra charge for using porcelain clay (it’s more than twice the price of regular clay), and for any third firing process! Once your work has been fired it can not turn back into clay for millennia – so don’t fire it if you don’t like it! Put it in the bucket for recycling. https://firebirdstudios.com.au/the-process-of-making-pottery/Ceramics have evolved over thousands of years.A white earthenware side plate with a gadroon edge. Has water marks and chips on front.‘Johnson Bros England Reg No 15587’flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, johnson bros, ceramics, tableware