Showing 324 items
matching indicators
-
Flagstaff Hill Maritime Museum and Village
Instrument - Scale, George Salter & Co, Circa 1921
The Hughes’ Family Scale No. 48 is a spring balance scale. It uses the Imperial measurements of ounces and pounds. There are 16 ounces (OZ) in one pound (LB), and each pound equals approximately 454 grams in Metric measurements. Scales have been used to measure and compare items for value for centuries. A weight was placed on one side of a balance and the object was placed on the other. Adjustments were made to either the weight or the object until the balance was horizontal, which meant that each side was the same weight. The Salter family business began in 1760 with spring makers, Richard and William Salter. In the late 18th century, Richard Salter invented the spring scale, where the weight of an object on the tray of the scale causes pressure on a spring in the scale. The pressure caused by gravity was then measured to calculate the weight of an object. Spring scales are still used today along with the more recent and accurate digital scales. The company began manufacturing in West Bromwich, England, in 1770. The firm was taken over by William’s sons, John and George. In 1824, after the death of John, the firm became George Salter & Co. The company produced a wide variety of products, including Britain’s first bathroom scale and the first English typewriter. In 1884 the Salter Trademark of a Staffordshire knot pierced by an arrow was registered. After over 100 years of manufacturing, the company was bought out by Staveley Industries, which was bought by Weigh-Tronix, and then that company was bought by HoMedics Company in 2004.This scale was made by Salter, the company that invented the balance scale, the first British bathroom scale and the first English typewriter. The scale represents the domestic equipment used for measuring in food preparation over 100 years ago. Modern kitchen scales are still using the same principal, along with scales used in business and industry.Scale; a domestic spring balance scale for measuring weight from 0 to 20 pounds. The scale’s grey metal case has a round white dial on the front with black markings, an arrow indicator and a round shallow metal bowl on a pedestal at the top. The scale is raised on a rectangular metal base with outward-sloping sides. An adjustable screw is on the dome top. The scale is marked from 0 to 20 pounds, with each pound marked in 1-ounce increments. The scale is named the Hughes Family Scale No. 48 and was made in Britain by Salter.“HUGHES’ / FAMILY SCALE / No. 48” “BRITISH MADE” “TO WEIGH 20 LBS BY 1 OZ” “SALTER” above logo [knotted rope with an arrow through loops]flagstaff hill, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, hughes, salter, british made, family scale, no. 48, spring balance, scale, weighing instrument, weights and measures, weighing machine, kitchen utensil, baking accessory, domestic equipment, cookware, bakeware, kitchen scale, kitchen accessory, food preparation, recipes, cooking, measuring -
Australian Gliding Museum
Machine - Glider – Sailplane, Construction completed 1952
This unique aircraft was conceived in 1943 as a two seat trainer. A very large part of the design work can be attributed to Jock Barratt and Harold Bradley. The general layout adopted is similar to the Kite I and Kite II single seat sailplanes of Martin Warner and Allan Campbell. Having regard to this heritage, the glider was originally named Kite III but renamed Pelican 2, perhaps because it was the second two seat training glider built by the Waikerie Gliding Club – the first being the Pelican, a reconfigured Pratt Utility glider. Pelican 2 was first flown in 1952 and regularly since then, at least until about 1992. The Pelican 2’s performance was found to be very good for sailplanes of its era and was often used for more advanced flying in addition to training new pilots. Very few changes have been made to the Pelican 2 over the years. The undercarriage was modified after its initial testing to improve the placement of the wheels. The trailing edge of the rudder (originally straight) was rounded adding to the surface area. The twin shoulder tow line bridles were replaced with a belly hook when aviation design rules declared shoulder bridles dangerous and a nose hook has since been added to allow for aero-towing. A unique home grown sailplane design associated with Australian gliding pioneers Wooden 2 seat glider sailplane with fabric covering. Distinctive features include the pod and boom fuselage with side by side seating for pilot and a second person. The canopy of perspex supported by aluminum framing opens with port and starboard segments separately folding upwards and forward. The instrument panel includes altimeter, airspeed indicator, slip indicator and variometers. In addition to the usual controls, there is a trim operated by a small wheel mounted centrally, at head height, on the bulkhead at the rear of the cockpit. Incorporated in the skid under the fuselage pod are two wheels (one approximately midships and the other at the rear end). It has a three piece cantilever wing of approximately nearly 17 metres. The ailerons run almost full length of the outer wing segments. A Gottingen 426 section has been used changing to M6 at the tips. Outer wing segments are joined to the centre section to give about 300 mm of dihedral at the tips. The glider is equipped with airbrakes. The colour scheme consists of orange fuselage with black nose and skid. The tailplane / elevator and rudder are painted white. The wing is predominantly white with an orange leading edge. Registration VH-GFY On each side of rudder – “Pelican II” in black lettering on a rectangle of silver On each side of fuselage pod the letters ‘FY’ On each side of the fuselage, below the edge of the cockpit opening – “WAIKERIE” in black paint. australian gliding, glider, sailplane, kite, pelican, waikerie gliding club, jock barratt, harold bradley, martin warner, allan campbell -
Flagstaff Hill Maritime Museum and Village
Tool - Ship Taffrail Log Flywheel, 1930+
The flywheel possibly belongs to a Walker's Cherub Mark III Ship-log taffrail, how the flywheel operates is a metal loop of the recording log would have been connected to the flywheel, so you could see if it was spinning properly. After the flywheel, is the rotor that was towed behind the ship and the revolutions of the rotor would register on the indicator, thus measuring the distance the vessel had travelled. Thomas Ferdinand Walker (1837–1921) first patented the Cherub log in 1878. It was one of the first logs in which the recorder was placed onboard a ship rather than being incorporated as part of the rotor. The Cherub Mark III series was produced from 1930 it came in two versions a thousand-mile which is quite rare and a five hundred-mile version.This ship log flywheel was invented and made by a significant marine instrument maker and innovator of machinery Thomas Walker. It demonstrates the huge leap taken to improve navigational accuracy at sea with an instrument that was in use for decades to measure the distance travelled at sea updated versions are in use today by mariners.Log Governor (or Fly-wheel) from a Ships Taffrail Log, metal wheel with 6 spokes, hub has rope attached for connecting to ships log. Boss the other side for attachment to the spinner.Noneflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, log governor -
Warrnambool and District Historical Society Inc.
Badges, TOC-H Badges x 3
TOC H was founded as a Christian organisation during the First World War in Belgium in 1915. Talbot House was a venue for respite from the war for soldiers and civilians. During the 1920s TOC H spread around the world especially to Commonwealth countries. In 1923 the Governor General of Australia wrote to The Reverend "Tubby" Clayton indicating that he and Lady Forster wished to endow a TOC H lamp, the symbol of TOC H in memory of their two sons who were killed in the war. The lamp symbol is a replica of the lamp used to provide light to early Christians who sought refuge in the catacombs of Rome. The cross of Lorraine is an indicator of its origins in the Ypres salient.The lamp is a symbol of an ongoing commitment of TOC H to spread light wherever it may be required. These badges are maintained as mementos of the Warrnambool branch of TOC H which operated from a sandstone building in Koroit Street Warrnambool. It was active during the middle decades of the 20th Century .1 Octagonal metal and enamel badge featuring a gold coloured oil lamp and cross on a green luminous background with rays emanating from the lamp. The badge has a gold edging. The reverse has a pin clip and text .2 and .3 Octagonal metal and enamel lapel badge featuring a gold coloured oil lamp and cross on a royal blue background. The badge has a gold edging. The reverse has a horseshoe shaped device to allow the badge to be secured in the buttonhole of a jacket. .1Indecipherable .2 Stokes and Sons Melbourne .3 2849toc h, tubby clayton, lord forster -
Southern Sherbrooke Historical Society Inc.
Photograph - Photo - A truck owned by Bill Hermon is apparently being refuelled
B&W photo of an open tray truck parked in front of a fuel pump on rough open ground with trees in the background. There is a tall pole beside the pump. The truck has 'MILL ENDS Phone EMERALD 61' painted on the side of the tray, and 'W. J. Hermon/EMERALD/61' painted on the door. There is a manually operated turning indicator – a large white hand shape on a pivoting rod – attached to the door. It appears that the signal is operated through the open driver's window. An unidentified man is in the driver's seat and he is smiling at the camera. Dated 1948. -
Ballarat Tramway Museum
Photograph - Black & White Photograph/s, c1910
Black and white photograph the intersection of Sturt St. and Lydiard St., Ballarat, north side, c 1905 to 1910. Two trams, ESCo No. 14 and 11?, east bound in street, with many people lining the streets, a precursor to a parade? Both trams have the original four side roof mounted destination indicators. Photo also has a number of horse drawn cabs and vehicles in photo. Winter photo? - long shadows. Copy 1 made for No. 12 display 3/99. High Resolution image added 31/8/2012trams, tramways, sturt st., esco, lydiard st. , tram 14 esco, 11 esco -
Melbourne Tram Museum
Newspaper, The Sun, “Tramming it in comfort”, 24/03/1973 12:00:00 AM
Newspaper clipping titled: “Tramming it in comfort” The Sun, 24/3/73 Photo and text of Melbourne’s newest tram Equipped with stop lights and indicators. Melbourne’s newest tram made first appearance at Preston workshops. Orange undercoat. Wide gangways give tram a spacious look, brown padded seats for 48 people. Even heated. Will take another 5 years at present rate of production for 99 others. Transport minister, Wilcox, said can travel at 45 mph. Number of people travelling on trams has increased in the past six months.trams, tramways, prototype tramcar, bourke st, preston workshops, tram 1041 -
Melbourne Tram Museum
Document - Report, Public Transport Corporation (PTC), "Public Transport Corporation - 1996 Annual Report", Oct. 1996
Book, centre stapled, 48 pages + card cover, printed on off-white paper full colour, titled "Public Transport Corporation - Annual Report 1996", providing a report to the Victorian Government on the performance of the PTC for the year 1995 - 1996. Includes a table of contents, Executive Review, attracting customers, changes and improvements, performance indicator, statutory information and Financial statements. Signed by Max Moore-Wilton as Chairman. PTC Chief Executive - Ian Dobbs. Alan Brown was the minister at the time. Has the theme "Moving from a system to a service".Has a white sticker on the front cover ""SOL T"trams, tramways, ptc, annual reports, melbourne -
Bendigo Historical Society Inc.
Document - MINING REPORTS - EXTRACTS FROM PRINCESS DAGMAR MINE MANAGER'S REPORT
Two copies of handwritten extracts from the Mine Manager's of the Princess Dagmar Mine, Garden Gully line. Mine Managers were J. Ebboth, Charles Gambetta, A. Williams and S. Richards. Subjects reported on include: supply of water to boiler, new engine- driver, stolen gold, engine house destroyed by fire, painting and cementing the chimney stack, sale of galvd iron and oil barrels, contractors erecting machinery, crushings, repair to shaft, new ropes, broken indicator on winding engine and work stopping and recommencing seven months later. Reports range in date from 1881 to 1914.document, gold, mining reports, mining reports, extracts from princess dagmar mine manager's report, john ebbott, mr roberts, mr lansell, john roberts, bendigo advertiser sat jan 23rd 1897, harkness and coy, almond williams, mr r eddy, f warren, s richards -
Whitehorse Historical Society Inc.
Equipment - Camera, 1951-1954
Kodak Retina 1a 35mm bellows camera with extending bellows, in a leather case (.02) and an Instruction book (in German .03). The camera has a chrome trim with leatherette over the rest of the steel forming the body of the camera. It has a Retina Xenar F 2.8/50mm, Schneider - Kreuznach 2668277 lens covering speeds from B (bulb) to 1/500th of a second and an aperture opening of f2.8 to f16. Provision for a hot flash and various film speeds. Film advance lever with indicator showing number of photos taken. An old cartridge (.04) is loaded in the camera. Four pieces make the set.Kodak Retina Camera|Retina 1a|Kodakphotography, cameras -
Kiewa Valley Historical Society
Console Telephone 10 shutter, circa early 1900s
This manual telephone exchange console is an important piece of equipment which provided the most efficient method of long distance communications in the 1950's to the 1980's. Communications were critical, not only for the regional Hospital, but also for large construction sites i.e. the Kiewa Hydro Scheme, especially if they are in dense rugged mountainous regions. The degree of Occupation Health and Welfare on industrial sites were at a bare minimum compared to the work scene after the 1980's.This telephone exchange console is highly significant to both the Kiewa Valley and Mount Beauty region because it was so important in the communications field relating to operational safety and work related controls. The success of any large undertaken relies heavily upon good communications. In the hospital this method of communications is still used i.e. patient to ward station. This flag system link a patient's room to the controlling nursing station. Identification of the patient needing help is crucial for swift action from the available medical staff. Similarly in large construction sites such as the Kiewa Hydro Scheme, successful instant communications was also essential. This switchboard required a 50 volt supply to successfully operate and was in use when both telecommunications and postal were under the one Federal Government carrier i.e. The Post Master General. A benefit with a line communication system (such as the one that fed this console was that interference from atmospheric conditions did not impede the connection.This console telephone switchboard (manual) unit has a shutter operation (precursor to the light indicator) to identify the caller to the telephone switchboard operator. This switchboard has a ten point indication shutter system allowing the operator to clearly identify where the caller is located. The console has a 44 connection point holes with their configurations in a triangular shape. The shutters are held closed by a small lever at the top which is opened by a small electrical charge from the incoming call. The operator uses a wind up handle to power a magneto connector(handle on the console's right side). The telephone hand set is located on the left side of the console. sec vic kiewa hydro scheme, alternate energy supplies, alpine population growth and communications -
The Beechworth Burke Museum
Geological specimen - Ventifact (wind- or ice-shaped) pebble
Ventifacts are sand-blasted rocks that are typically faceted and often display parallel grooves carved by wind-blown sand. They are useful indicators of wind direction and strength in environments such as deserts, mountains, and coastal areas because they are usually not hidden by later sediment, soil or vegetation cover. In Antarctica ventifaction is strongly related to the composition or type of rock. Ventifacts are important because they provide evidence for abraders such as sand, dust or snow and ice crystals, and offer a unique understanding of past wind processes that are effective in the reconstruction of past wind flow conditions and can provides clues to weather and climate changes in the past. Interestingly ventifacts have also been found on the surface of Mars. They were a threat to the NASA rover due to the sharp angles of the facets, created by the Martian wind over the course of millions of years. These Martian ventifacts act like weathervanes for past wind and weather patterns on the red planet in a similar manner to those found on earth.The Geological Survey of Victoria was instigated in response to the Victorian Gold Rush which began around 1851 in the Beechworth, Castlemaine, Daylesford, Bendigo and Ballarat areas. The survey was conducted by Alfred Richard Cecil Selwyn from his arrival in December 1852 until his resignation in 1869and during this time he trained many notable geologists, e.g. Aplin, Wilkinson, Daintree, who went on to other State survey senior positions. This specimen was among those donated to the Burke Museum in 1868.A hand-sized solid mineral specimen in shades of dark and light browns with light lines visible in all configurations and a groove on configuration 2.light lines visible in all configurations and a groove on configuration 2burke museum, beechworth, geological, geological specimen, ventifact, antarctic region, antarctic, alfred richard cecil selwyn, alfred selwyn, wind direction, wind strength, abraders, wind flow, climate change, reconstruction of wind flow conditions, weather change, mars -
Ballarat Tramway Museum
Postcard, WTP, Sturt St taken from Grenville St, c1906
Shows horse-drawn vehicles and one electric tram arriving at the terminus, late in the evening. Shows the little shed at the terminus, and buildings on either side of the Sturt St. People waiting around the tram stop. The tram seems to have a "color" light indicator above the driver. Titled "Sturt Street, Ballarat" in red ink in the top left-hand corner. On the rear of the card, has the stamp "R. M. Noy, Postcard collection", cancellation stamp of Ballarat East, 23.5.07, 1d Victorian stamp. Written to Miss Victoria Kemsey? of 225 Victoria Parade, East Melbourne, wishing her many happy returns on the day. Has the logo of WTP." in the top centre of the card. Divided back type. On rear of 2nd copy is a letter to Mrs Spronston of Skelton Cottage Avoca - date stamp not readable. 2nd copy has the publisher "JE" on the rear upper centre.Yields information about Sturt St Ballarat and demonstrates Australian printed colour photo postcards.Colour postcard of Sturt St taken from Grenville St looking down at the Grenville St terminus.Has in pencil $12 along top edge on rear and two stickers "P/U Ballarat" and "Ballarat Vic Tram" both of which had become loose by the time the item was stored.trams, tramways, postcards, sturt st, ballarat, grenville st -
Melbourne Tram Museum
Administrative record - Annual Report/s, Metropolitan Transit Authority (MTA), "Metropolitan Transit Authority of Victoria Annual Report - 1983/84", 1984
Annual Report - 44 pages, A4, gloss card cover, with fold out front cover, gloss printed pages, centre stapled. Features photos of passengers at a railway station, tram stop and a bus stop. Has forward by L.A. Strouse Chairman and Managing Director to the Minister of Transport Steve Crabb. Includes list and photographs of the Board Members, including F. D. Snell, N. Maddock, K. Dunstan, and J. Grigg. Includes a table of contents. Gives information on the Authority, its make up, work including new uniforms. Has a detailed financial statement and balance sheet, personnel statistics and performance indicators. Includes ticketing rearrangements.trams, tramways, annual reports, the met, uniforms, public transport, mta, personnel -
Trafalgar Holden Museum
Vehicle - Holden FE special sedan, July 1956
BY THE time the FJ Holden was replaced with the FE in July 1956, Australia’s own had taken many steps forward. The six-volt electrics were replaced with a 12-volt set-up, the two-piece windscreen was replaced with a single curved item and the skinny 15in rims were replaced with 13x4.5 steelies. Unlike the FX-FJ, the FE was designed locally by an Australian team. The resulting car was much sleeker than the earlier models, being two inches longer in the wheelbase, four inches longer overall and slightly heavier than its predecessor. To compensate, the 132ci grey motor was blessed with another small dose of horsepower thanks to larger valves and improved cylinder heads. Other mechanical improvements included pendulum-style brake and clutch pedals, hydraulic clutch actuation, larger brake drums and recirculating ball (rather than worm and sector) steering. Other great leaps forward included optional heater, indicators, reversing lights, windscreen washers and demister. In knocked down form was the first model to be exported to New ZealandBlack painted special sedan. Added accessories include exterior sun visor, headlight protectors, and on the interior grab handle mounted across the back of the front seatDiecast special sedan badge on rear quarters. Number plate club permit 63450 Hfe special, holden, sedan, car -
Australian Gliding Museum
Machine - Glider – Sailplane, 29/071956
The Slingsby T31 is a two seat training glider that came available in 1951. It is, in effect, a two seat version of the single seat Kirby Tutor. The T31 was marketed by Slingsby Sailplanes both as complete aircraft and kits of parts for assembly. The Australian Gliding Museum’s example (currently registered as VH-GDB) is one of five of this type to grace Australian skies. Three including GDB were assembled in Australia from kits supplied by Slingsby’s in England, the other two were delivered as completed airframes. To date only four remain of which two are airworthy. This aircraft began flying in at Caversham in Western Australia (the then home of the Gliding Club of Western Australia) in July 1956. It was badly damaged in a crash in June 1958. The wreckage was sent to Schneiders in Adelaide for repair. However, the Club decided against having the repairs done, opting instead to buy a new ES52 Kookaburra. After a couple of years, the wreck was purchased by a member of the Waikerie Gliding Club whereupon the glider was rebuilt with some modifications, including a more rounded and better streamlined fuselage nose. It returned to the air in October 1961 at Clare in South Australia. The ownership of VH-GDB passed through a number of clubs, including at Dubbo in New South Wales, Wimmera in Victoria and Pioneer Valley at Mackay in Queensland. Eventually, it came into the hands of Bill Riley of Tocumwal in New South Wales who held it in storage for many years. Riley donated the aircraft to the Museum. It has been restored to airworthiness and is flown at vintage glider rallies and on Museum open days. This exhibit is an excellent example of a Slingsby T31 Tandem Tutor, a type of glider that was used by a number of clubs in the 1950s and 1960s for dual training of pilots to the solo capability.The Slingsby T31b Tandem Tutor is an open cockpit, tandem, two-seater glider with high, pylon mounted two piece wing supported by double, wire braced, steel tube struts. The glider is fitted with a main wheel, rubber-block sprung, wooden nose skid and steel leaf sprung, brass shod tailskid. The basic controls of aileron, rudder and elevator are not supplemented with pitch trim. Wing lift spoilers and both aerotow and winch releases are fitted. The instrument panels in both cockpits are fitted with an airspeed indicator, cosim variometer and altimeter. This red and silver painted wood and fabric covered aircraft is in excellent condition having been restored to full airworthy status by the Australian Gliding Museum. SLINGSBY – T31b (nose – both sides) DB Australian Gliding Museum (rudder – both sides) It has been given Serial Number GFA/HB/12 and is registered as VH-GDBaustralian gliding, glider, sailplane, slingsby, tandem tutor, t31, gliding club of western australia, waikerie gliding club, wimmera soaring club, pioneer valley soaring club -
Vision Australia
Equipment - Object, Wormald International Sensory Aids Ltd, Mowat sensor, 197
The Mowat Sensor model MS 01, is a pale green, palm-sized, plastic battery-operated device with a darker green switch on top. It is partially open at one end with two grilles. A microphone plugs into the other end with a wrist strap. It came with a brown vinyl carry case and owner's manual, which are not included. This handheld device for the visually impaired uses high frequency sound to detect objects within a narrow beam. The sensor vibrates if an object is present, responds to closest object within the beam. The vibration rate increases as user approaches object. There are two range settings: short, responds to objects less than 1 meter away (indoor use) and long, responds to objects of sufficient size up to 4 meters. The sensor can be handheld or carried in pocket or purse. As a facility intended for partially sighted people, the compass also includes an in-built color indicator (visible through the semi-transparent enclosure), which indicates the direction using a combination of three colours. Weight: 185 grams. Comes with dark brown vinyl case.1 pale green coloured plastic rectangle sensor with a brown nylon, plaited wrist strap Model MS01assistive devices, orientation and mobility -
Melbourne Tram Museum
Photograph - Black and White photograph, mid to late 1970's
Set of four black and white prints of MMTB buses - MMTB "Official" photographs. .1 - bus 346 - AEC Regal Mark 3 - Comeng .2 - bus 553 - AEC Regal Mark 3 - Martin and King .3 - bus 620 - AEC Regal Mark 4 .4 - bus 588 - AEC Regal Mark 3 - Martin and King - close up of the driver's exit door, rear view mirror, turn indicator (the hand operated type to show either a stop or a right hand turning using a cut out of a hand. Shows the radiator and head lights. .5 - as for .3, but with the doors closed. Information about the buses from: https://fleetlists.busaustralia.com/vicdisp.php accessed 3/9/2019trams, tramways, mmtb, buses -
Melbourne Tram Museum
Newspaper, "Supertram", c1971
Newspaper clipping titled - “Supertram” Photo and text of model of new 70s tram Undetermined source & date Wilcox – transport minister, full scale prototype to cost about $100,000 being constructed by the Tramways Board, new trams will require no major overhauls for 12 years, model 5ft long, 12 inches high, heating in winter, near-noiseless journey, separate entrances and exits, all-electric braking, automatic acceleration and deceleration for a faster operating speed and a more comfortable ride. Passengers will pass a seated conductor at the front entrance. Eliminate fair evasion, estimated at 9% of fare revenue. Wilcox will ask Treasury to approve purchase of 100. Full-scale prototype to have tail and stop lights, and indicators.trams, tramways, prototype tramcar, models, lights -
Federation University Historical Collection
Book, George Brown, Prospectors' Guide (Victoria), 1936
... indicators ...Brown soft covered book with pullout map showing auriferous areas of Victoria. prospecting, gold, geology, quartz reefs, indicators, ballarat indicators, miners' rights, mining leases, forest regulations, equipment, gold cradle, puddling machine, sluice box, whim, whip, california pump, cradle, mining, tools, mining laws -
Flagstaff Hill Maritime Museum and Village
Equipment - Ship's Telegraph section, A. Robinson & Co. Ltd, Late-19th to mid-20th centuries
The ship’s communication system that was used from the late 19th century to early-to-mid-20th-century is called an Engine Order Telegraph (E.O.T.) or ship’s telegraph. The system has two parts, the Bridge Section and the Engine Room Section. The Bridge Section is usually mounted on top of a pedestal, and the Engine Room Section is often attached to a vertical surface. The standard commands printed or stamped onto the dial are the directions of AHEAD and ASTERN, and the speeds of STOP, SLOW, HALF, and FULL. The ship’s pilot on the Bridge of a vessel sends his Orders for speed and direction to the to the Engine Room with the E.O.T. He moves the lever or levers, depending on the number of engines the ship has, to change the indicator on the Bridge Section’s dial to point in the new direction and speed of travel. This change causes the Orders to be duplicated on the Engine Room Section’s dial and a bell to signal the change at the same time. The engineer then adjusts the ship’s engines and steering equipment to follow the pilot’s Order. The manufacturer, A. Robinson & Co. Ltd of Liverpool, established his business in 1780 and continued until 1968 when the business was purchased by marine products maker Chadburns, established in London in 1870.This Engine Room section is part of a ship's telegraph communication system and represents marine technology used in the late-19th to mid-20th-century. Engine Room Section of a ship’s telegraph or Engine Order Telegraph (E.O.T.). The round brass dial has inscriptions stamped around its edge and centre. Red inlaid glass plates have inscriptions in white paint on them. The inscriptions are nautical terms for direction and speed and include the maker’s details. A rotating pointer is joined to the centre of the dial. The maker is A. Robinson & Co. Ltd of Liverpool. Stamped: “FULL / HALF / SLOW / STOP / FULL / HALF / SLOW / STOP”, “AHEAD / ASTERN” Printed: “FULL / HALF / SLOW / STOP / FULL / HALF / SLOW / STOP” Stamped on the dial: “A. ROBINSON & CO. LTD / MANUFACTURERS / LIVERPOOL”flagstaff hill, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, marine technology, marine communications, engine order telegraph, e.o.t., ship’s telegraph, bridge section, engine room section, ship’s engine telegraph section, marine telegraph, a. robinson & co. ltd, liverpool -
Parks Victoria - Wilsons Promontory Lightstation
Muslin & Wick
This item, which dates to 1988, is contained in the original supply packet and survives in good condition. It was commonly used by lightkeepers for both wet and dry bulb thermometers, with the muslin going into the bottom of the dry bulb where it was held in place by the wick and ‘end of the wick was then placed in a jar of deep water to keep the bulb cool’. The difference in temperatures between the dry and wet bulb thermometers could then be worked out to establish the dew point in the air.They were common in lightstations, but this intact item remains in the original packaging and is a fine representative example of its kind. It was acquired from the Bureau of Meteorology. Recording and communicating weather readings was an important facet of lightstation work and a number of different but related items of meteorological equipment survive at the six lightstations managed by parks Victoria. The Cape Nelson collection includes a pair of Australian-made thermometers in their original box, both in Fahrenheit, with one recording the minimum, the other the maximum temperature and a barometer table with instructions for correcting readings. Cape Otway has a Beaufort Scale, a table of wind forces which lists 12 types on a scale of 1 to 12, and provides associated speed in knots and travel time per minute or hour. Gabo Island has an anemometer, wind speed indicator and a wind speed recorder.Muslin and wick for a wet bulb thermomenter in unopened white paper packaging with directions for use printed on the package on the front.On front of package,"MUSLIN AND WICK FOR WET BULB THERMOMETER......." -
Flagstaff Hill Maritime Museum and Village
Equipment - Ships' Telegraph section, Milne Brothers, Copper and Brass Works, Early-to mid-20th century
This Engine Room section of a ship's telegraph system was part of the equipment of the Ports and Harbour ship the SS Rip. The vessel serviced and maintained the lights and buoys at Port Phillip Bay and Queenscliffe. The SS Rip was possibly the former gunboat "Albert". The ship’s communication system that was used from the late 19th century to early-to-mid-20th-century is called an Engine Order Telegraph (E.O.T.) or ship’s telegraph. The system has two parts, the Bridge Section and the Engine Room Section. The Bridge Section is usually mounted on top of a pedestal, and the Engine Room Section is often attached to a vertical surface. The standard commands printed or stamped onto the dial are the directions of AHEAD and ASTERN, and the speeds of STOP, FULL, EASY, STD. BY. and FIN. ENG. The ship’s pilot on the Bridge of a vessel sends his Orders for speed and direction to the to the Engine Room with the E.O.T. He moves the lever or levers, depending on the number of engines the ship has, to change the indicator on the Bridge Section’s dial to point in the new direction and speed of travel. This change causes the Orders to be duplicated on the Engine Room Section’s dial and a bell to signal the change simultaneously. The engineer then adjusts the ship’s engines and steering equipment to follow the pilot’s Order. The manufacturer, Mulne Bros., was a copper and brass works at 166 Sussex Street Sydney, in December 1892, and previously from 1870 at 128 to 130 Sussex Street. The company made and sold a wide range of equipment including machinery and gauges for the Railways.The Engine Room section is significant for being part of the communications system on the ship SS Rip, owned by Melbourne's Ports & Harbours department and used to service and maintain the navigation signals of Port Phillip Bay and at Queenscliffe in the mid-20th century. The dial is an example of marine equipment made in Australia and used for the safety of Victorian vessels. It is also significant for being made by an early Australian manufacturer, Milne Brothers of Sydney.Engine Room Section of a ship’s telegraph or Engine Order Telegraph (E.O.T.). The round metal dial has inscriptions stamped around the edges. The inscriptions are nautical terms for direction and speed and include the maker’s details. The dial was made by Milne Bros. of Sydney. It was part of the equipment on the "SS Rip" in Victoria.Black paint around dial: "MILNE BROS. / MAKERS / SYDNEY" "FULL EASY STD. BY " "FIN ENG. EASY FULL" ""ASTERN" "STOP" "AHEAD"flagstaff hill, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, marine technology, marine communications, engine order telegraph, e.o.t., ship’s telegraph, bridge section, engine room section, ship’s engine telegraph section, marine telegraph, milne bros., milne brothers, sydney, copper and brass works, ports & harbours ship, ss rip, gunboat albert, service ship, maintenance ship -
Federation University Historical Collection
Document - Document - Project, VIOSH: University of Ballarat, Strategic Plan; Quality Management Project 1994
Victorian Institute of Occupational Safety and Health (VIOSH) Australia is the Asia-Pacific centre for teaching and research in occupational health and safety (OHS) and is known as one of Australia's leaders on the field. VIOSH has a global reputation for its innovative approach within the field of OHS management. VIOSH had its first intake of students in 1979. At that time the Institution was known as the Ballarat College of Advanced Education. In 1990 it became known as Ballarat University College, then in 1994 as University of Ballarat. It was 2014 that it became Federation University. VIOSH Australia students are safety managers, senior advisors and experienced OHS professionals. They come from all over Australia and industry. Students are taught active research and enquiry; rather than textbook learning and a one-size fits all approach. VIOSH accepts people into the Graduate Diploma of Occupational Hazard Management who have no undergraduate degree - on the basis of extensive work experience and knowledge. Memo from Don Maconachie was sent to all VIOSH Staff in relation to the development of a VIOSH Strategic Plan. They were to develop value statement, vision statement, aims, goals, objectives, targets, strategies. Staff provided with forms to be completed coving these aspects. They were to state the responsible person, timeline, target groups, resources required and indicators of success. On completion results compiled and given to staff. Report would then be sent to Director of VIOSH Australia.Forty-two pages that was stapled together in sections. Type written with relevant charts.viosh, victorian institute of occupational safety and health, quality management project, visor strategic plan, don maconachie, mission statement, aims, targets, director -
Federation University Historical Collection
Photograph (black & white), Ballarat School of Mines Students visit the Last Chance Mine, c 1898
The mining class visited the Last Chance on the afternoon of Thursday, 8th June, under the guidance of Mr Kirby, the mine manager. Mr Campbell, the photographic instructor, also dared the perils of the deep in order to take some flashlight photos. As this was Mr Campbell's first visit below, several difficulties which he did not now existed prevented success. The students all ranged themselves in poetic and heroic attitudes for the first flashlight, but the development of the plate showed only the light from the candles and the moisture on the lens. The next two tries were better, but were under-exposed, and of no value, except as experience. Two gentlemen from England also went below with the students, but history repeated itself and Australia won the "test." The Englishmen left early. Mr Hart secured a fine specimen of arsenopyrite and indicator slate; also a bootlace, the property of a much-vexed miner, whose boots Mr Hart had borrowed. Horrors! Mr Hart steal a bootlace! Impossible! However, a tragedy was averted by the miner securing a new lace, and he was at once all smiles - so were the students. Mr Campbell took a photo of the students dressed for the occasion, and some were flattered, and some looked very like the universal "Weary Willie". (Ballarat School of Mines Students' Magazine, July 1899, p.2.)Over 24 men pose for a photograph outside the Last Chance mine. Some of the men are members of the visiting Ballarat School of Mines mining class. Thomas Hart (beard) stands at the back right. Verso: Copied from Annual report 1898, Thomas Hart - back Row, 2nd from right with beard.ballarat school of mines, last chance, thomas hart, john rowe, hart, mining, mining alumni, rowe, charles campbell -
Trafalgar Holden Museum
Vehicle - VY Acclaim sedan, 2002
The front and rear of the body had minor restyling, with new front grille, headlights and taillights. The interior has been significantly upgraded. Interior upgrade includes a new instrument panel, centre console and steering wheel and new design transmission lever and handbrake.[2] There is also a new mobile phone power outlet under the centre console. The new instrument cluster features a large multi-function digital display (single or triple-window, depending on model), which displays information such as radio station display, PRND321 gear selected indicator, trip computer with stopwatch function, service reminders and a help facility. Standard features (on some models) now include "twilight sentinel" - automatic headlamp control, programmable headlamps off time delay, high feature Blaupunkt audio systems, road-speed sensitive intermittent wipers and passenger airbags. The VY Series II update added cruise control, front power windows variable front seat lumbar support, and revised interior trims. A 245 kW (329 hp) V8 was introduced to sports variants and a sportier repositioning of the Calais model. This repositioning included a subtle body kit, the option of a 235 kW V8 in place of the previous 225 kW (302 hp) and a firmer suspension tune (known as FE 1.5) that was not as stiff as the FE2 suspension on sports variants. Released in September 2002 and produced until August 2004 (with a Series II released in August 2003), the VY series was the first major design departure (both inside and out) of the third generation Commodore range released in August 1997. It launched at the same time as the Ford Falcon (BA).VY Holden 4 door sedan white paint with grey fabric upholsteryLion and stone emblem grille centre, V6 badge on mudguards, Commodore badge on boot LHS, Lion and stone badge on boot centre, Acclaim badge RHS of boot lidvehicle, commodore, car -
Federation University Historical Collection
Book, Australasian Institute of Mining Engineers, Transactions of the Australasian Institute of Mining Engineers, Volume X, 1905
Fabric covered hardcovered book of 367 pages. Includes a number of pullout plans. Contents * Mount Lyell Mining Field Tasmania by Professor J.W. Gregory * Concentration of solver-led ores (with 6 plates) by V.F. Stanley Low * Phosphate Deposites of Ocean and Pleasnt Islands (with 15 plates) by F. Danvers Power * Coal and Coal Mining in New SoPleassant Isuth Wales by Thomas Parton * Method of TImbering at the Mount Rex Tin Mne, Ben Lomand, Tasmania by Mark Ireland * Peck's Centrifugal Elevator by W. Peck * A Portable Assay Furnace by J.J. Gillio * NOtes on Sampling by A.C. Thomas * The Career of the Gold Dredge i n New South Wales by David K. Blair * The Transmission of Power by COmpressed Air in Mines by R.W. Chapman * The Misplacement of Mning Shafts and Adits in Victoria (with 7 figures) * The Indicators of the Daylesford Gold Mines, Victoria * Mining Accounts by R.N. Kirknon-fictionausimm, a.s. kenyon, frank a. moss, mount lyell, j.w. gregory, coal, gold dredge, transmission of power, mining shaft audits, daylesford gold mines, spitzkastens, ocean island banaba, pleasant island nauru, pinnacles on flat reef pleasant island, ocean island, blow hole howe bay, rock phosphate, thomas parton, mark ireland, mount rex tin mine, ngapara dredge, w. peck, w.h. vale, daylesford, jim crow diggings, glenmona gmc, f. danvers power, leigh g. hancock, workers' industrial union of australia (barrier district) -
Federation University Historical Collection
Document - Documents, Golden Point - Mount Pleasant Progress Association Establishment
The Golden Point - Mt Pleasant Progress Association was established on Wednesday 6 April 1983. Membership was open to any person or organisation in the area generally bounded by Bridge mall and Skipton Street, Elsworth Street and main Road. annual family or organisation membership was $2.00. Mara Gluyas served as secretary of the Golden Point - Mt Pleasant Progress Association from 1983 to 1994. Ian McKinnon was the President from 1983 to 1992. Kerry Daniels was the President in 1994.A small white cardboard box with purple lid of A4 documents relating to the establishment of the Golden Point - Mt Pleasant Progress Association. The documents include the original constitution and minutes. Topics include: Pearce's Park; removal of elms, names and addresses of members, Sovereign Hill realignment; Sovereign Hill Lookout; membership form; Golden Point Historic Mines Direction Indicator; Ballarat Observatory; Nerrina Tip; Yarrowee Creek; Mine Capping (Sovereign Mine); tree planting (Sovereign Hill Lookout); Magpie Street Park; Hill Street; Yarrowee Flora Park; Barkly Street; South Street Bluestone Gutter; Ballarat Goldfields; Eastern baths site; Grant Street; Flooding; Aboriginal Advancement League; Sunnyside Woollen Mill; Chinese Garden; Golden Point Primary School closure; Ballarat West Goldfields; Sovereign Hill Land Title and Management Revision; Wainwright; Street; Llanberris; Yuille's Station Parkgolden point, mount pleasant, mt pleasant, ian mckinnno, mara gluyas, peter hiscock, frank williams, geoff howard, leigh gillett, sovereign hill, kerry daniels, norm strange; graeme kent; george netherway; keith rash; ian mckinnon, albert graham, bryan crebbin, jim humphreys. wid radbourn, heath martin, janet dore, alex mills park -
Federation University Historical Collection
Book, Memoirs of the Geological Survey of Victoria No 14 The Ballarat Goldfields, 1923
William Baragwanath was educated at the Ballarat School of Mines, obtaining a Geology Certificate in 1911. After further study he went on the become Secretary for Mines, and Chief Mining Surveyor. Baragwanath was a Councillor of the Ballarat School of Mine from 1916 to 1950.Pink covered foolscap book of 257 pages and 32 maps and plans by William Baragwanath. Contents include topography, physiography, historical, geology, basalt, faults, dykes, minerals leads, alluvial mines, nuggets, structure of Ballarat West goldfields, structure of Ballarat East gold-field, quartz formation, indicators, defunct mines, existing mines, table of deepest shafts. Images include: section of the Ballarat Gold-Field, Dead HOrse Flat, lakes formed by Basalt Flows, Gong Gong Creek, Frenchman's Lead, Ballarat West Mines, LEases and positions of shafts (1857), puddling, White Horse Lead, Woah Hawp Canton, Ballarat Township mines, Sebastopol, syncline, Victoria United Line, First Chance Mine, Llanberris No 1 Mine, Saddle Reef, New Normanby Mine, Woah Hawp Canton Mine, South Star Mine, Sebastopol Plateau, south Woah Hawp Mine, Woah No. 2 Minegeology, geological survey no 14, ballarat, baragwanath, william baragwanath -
Victorian Aboriginal Corporation for Languages
Conference proceedings, Mary Jane Norris, Endangered languages beyond boundaries : community connections, collaborative approaches and cross-disciplinary research =? Langues en pe?ril au-dela? des frontie?res : connexions communautaires, approches collaboratives, et rechecrche interdisciplinaire : proceedings of the 17th FEL Conference Carleton University, Ottawa, Ontario Canada 1-4 October 2013, 2013
Session 1: Collaborations with language and cultural organizations, and governments Session 2: Collaborations with universities, researchers, institutes and schools Session 3: Strategies/issues across language, culture, geography, place and generations I: standardization and dialects Session 4: Strategies issues across language, culture, geography, place and generations II: Minority languages, regions and rural/urban areas Session 6: Language and culture connections: Health, well-being, and educational outcomes Session 7: Strategies/issues across language, culture, geography, place and generations III: Generations and families Session 8: Language assessment, documentation and diversity: Indicators of vitality, endangerment and the implications of data collection Session 5: Poster sessions I: Hard copy: Community connections, collaborative approaches, cross-disciplinary research Session 5: Poster session II: Electronic: Collaborative approaches with information and computer technologiesmaps, b&w photographs, colour photographs, illustrations, graphscollaboration, community involvement, cross disciplinary research