Hand operated washing machine - plunger type - a central cone plunger attached to a fulcrum point (adjustable in height) on side with a long arm. Depth of plunger action also adjustable. All mounted on a three leg frame. Container is slightly coned shaped at bottom and has a drain tap at bottom for emptying water. Container can also be lifted off. Provision made for attachment of a wringer (this could be a later modification). Plunger is approx 37cm in diameter and has four 1.5cm holes for water to be forced through. Unit is galvanised steel but frame appears to have been painted with 'Silverfros'.On Side of container - 'The Zwar' VACUUM Washing Machine Patent No 2089/31domestic items, laundering

Set of four hand written notes on off white paper. .1 - "Car 1041"All electric" Destination Indicators - giving a list of the destination blind fitted to prototype tramcar 1041 - dated 13-7-73. .2 - "Tail light modifications to W2's - gives a list of W2's yet to be fitted and notes on dates. .3 - "W2 Overhauls" - giving a list of W2's and dates of overhauls. - 1973? .4 - "Able bodies W2 trams (1973) - list of W2's in use?, depot, dates of overhaul and some comments in red ink.trams, tramways, 1041, destination roll, lights, w2 class, preston workshops, overhauls, tram 1041

Sir Frederick William Hewitt (1857-1916) wrote one of the earliest comprehensive textbooks on anaesthesia, and designed several pieces of anaesthetic equipment. In 1901, he described his wide-bore ether inhaler, a modification of the Clover Ether Inhaler. Unlike the Clover, it can be refilled with ether while still in use, and the mask is screwed into place so that it "cannot be unexpectedly detached." This version is a modified Hewitt's Inhaler which has a narrower 'ways' than the original Hewitt's, and no water compartment. Additionally, one side of the bowl is made of glass which enabled the person administering anaesthesia to see the level remaining in the bowl. Bowl shaped inhaler with a glass bowl base and metal dome top with a connector which appears to be for a rebreather bag. There is a metal switch at the base of the glass bowl to alter or regulate the flow.Stamped into central tube: COXETER LONDON Stamped into side of metal dome: 6460hewitt, wide-bore, clover, ether, anaesthesia, anesthesiology, anaesthesiology

Sir Frederic W. Hewitt (1857-1916), an accomplished and well respected English anesthesiologist, was an expert in the function and use of the Clover Ether Inhaler. In 1901, Hewitt described his modification of the Clover Inhaler. Often referred to as the Hewitt Wide-Bore Inhaler, Dr. Hewitt introduced changes in order to make it easier to breathe through the device and improve the ventilation of oxygen and carbon dioxide. In 1901, Hewitt was recruited to anesthetize King Edward VII for emergency abdominal surgery. This was just a day or so before the new King was to be coronated. He recovered well, and Hewitt became the first anesthesiologist ever to be knighted. (Source: Wood Library Museum)Tall black round topped box with brass hooks at the sides and brass hinges at rear. There is a brown fabric handle on the top. The box has red padding inside the lid and red lining inside the base and sides. There is a round section in the base of the box for holding the round clear glass bottle for ether. There is also a ellipse-shaped metal inhaler on small metal base with a thin metal handle and pipe with bakelite plug attached via a small metal chain. A brown mask is made of brown leather and celluloid which is connected to the inhaler. There is a metal ether measure for pouring the ether.On notecard in box: (B) HEWITT'S INHALER 1895, MADE BY GEO. BARTH & CO LTD., ADVERTISED AS THE SOLE MAKERS OF THE INHALER AND RECOGNISED BY HEWITT IN HIS TEXT BOOK - ANAESTHETICS AND THEIR ADMINISTRATION - AS THE MAKER OF HIS INHALER. / GIVEN BY DR. E.S. HOLLOWAY IN 1951, WHO ACQUIRED MUCH OF HOWARD JONES' EQUIPMENT AFTER THE LATTER'S DEATH. Stamped on underside of glass bottle in a circle: WUBW [illegible] Blue sticker on inhaler: O.2.13. Printed on inhaler under handle: Geo Barth [illegible] / SOL [illegible] Printed on body of inhaler: Full Printed on body of inhaler: 1/2 Printed on inside of leather mask: F35hewitt, sir frederic, jones, howard, inhaler, geo. barth & co. ltd., ether

This image is from Wodonga Historical Society's large collection of photographs documenting the construction of the Hume Dam during its initial construction and ongoing development. Hume Dam took 17 years to construct from the turning of the first sod on 28 November 1919 by Sir Ronald Munro-Ferguson, Governor-General of Australia. The first filling was in December 1934 and it was officially opened on 21 November 1936. Between 1950 and 1961 further modifications were made which enlarged its storage capacity. Progressive improvements have been made since that time to ensure the dam meets modern safety standards.This photo reflects a major stage in the construction of the Hume Dam.A large black and white image of construction of the Hume Weir on the Murray River mounted on board.hume dam construction, hume weir australia

Photographs of H class car 60 at the Kew Depot c1920's. .1 - Tram painted in MMTB chocolate and cream colour scheme. Side elevation photo with depot buildings in background. Taken prior to modification of roofs at end of cars to building in destination box. Tram of same class at SEC No. 18. Tram E45 can be seen in the shed. .2 - Front elevation photo with depot buildings in background. Has old style destination box on roof, showing "DEEPDENE" and a route number box above the headlight. Both photos Print and photograph by Sutcliffe of Cromwell buildings 366a Bourke St. Melbourne.Yields information about H class tram No. 60 and Kew DepotSet of two Photograph, Black and White, In ink on the rear: .1 - "M&MTB H-60, Kew Depot `1920's (E45 in shed)" and the photographers stamp. .2 - ditto. KSK print number SA938 and 939.trams, tramways, h class, kew depot, deepdene, e class, tram 60, tram 45

Dr. Joseph Clover (1825-1882), an English physician, first described his Portable Regulating Ether Inhaler on Jan. 20, 1877. Clover was an especially sought after anesthesiologist and early pioneer in the specialty. This was the best-known of many inhalers that Clover designed. The dome-shaped reservoir was turned to points on a control dial to gradually increase or decrease the percentage of the air that passed over the ether. Several inventors based new inhalers on this, while the original continued to be manufactured as late as the beginning of WWII.Metal dome chamber with flat base and two circular pains of glass on each side of the dome as viewing holes. There is a long connector tube with an elbow joint attached to a bulb for a rebreather bag. A previous exhibition label, typed in black ink on buff coloured card, has been tied to the connector.Moulded into the connector for the rebreather bag: MAYER & MELTZER No 212827 •Printed in white on blue sticker: O.2.9. •Stamped into dome: MAYER & MELTZER / LONDON •Typed onto exhibition label: MODIFIED CLOVER'S INHALER. / c.1906. / Name unknown. the modification consists / in windows to shew the ether-level in the / bowl. The inhaler has otherwise the same / restricted channels as the model of 1877 / and shares its faults. / (Gift of Dr. A.E. Rowden White, 1939).joseph clover, wilson smith

This item is part of a group of five green display boards with photographs of sheep. This item is associated with the New South Wales Graziers Association world tour of merino sheep 1928/9.Six black and white photographs and printed paper mounted on green display board. Photographs depict sheep and men. The display board has pin holes in each corner.Front: [handwritten] Typical Badgerface Ewe and Ram. / [printed] This pattern crops up in many breeds all over the world. It behaves / as a simple recessive to white. The typical pattern in very character- / istic, but many modifications are found so that badgerface sheep may range / from those that are almost white to those that are almost black. Back: [handwritten] Typical / Badgerface / ewe and ram / 4 / [printed] PHOTOGRAPH COPYRIGHT / BY / THE ANIMAL BREEDING RESEARCH DEPT., / THE UNIVERSITY, EDINBURGH. / PLEASE RETURN TO :new south wales graziers association, world tour, england, sheep, farm, rural, agriculture

This diary was written by Cpl William Donald McDonald 3403 who served from July 1915 to November 1918. The diary covers the period August 5th 1916 to December 31st 1917.William McDonald was stationed in England mostly at the Salisbury Plain for the entire period. This item was mistakenly identified as as the J A G Brass diary, with 11Lieut J A G Brass being written inside the front cover of the diary. However J A G Brass was a distant cousin of W McDonald who still lived in Scotland and along with other names inside the front cover were contacts for the writer. Among the names are A W Hardy, J W Jolly, I J Windsor, Pte H A Jessop. The book itself is a modified British Service notebook, having been cut down by the author to make it a more manageable size. William McDonald was 35 years of age when he enlisted and was a tailor before enlistingThis diary has historic significance as it records daily life during the first world war. It relates daily life in the army ranks. It also has strong links to local families.Modified Service notebook of the type issued for use in the British Army of World War 1. It would have originally measured 5” x 7”, but has been cut down by nearly removing the fly end of the pages to reduce them about 3.5”. The author, who was a painstakingly neat and fastidious man, has also re-rounded the corners, to prevent them ‘dog-earing’. The aim of the modifications is likely to have been to make the item easy to slip in or out of a tunic pocket. Heavy light grey green card with rounded corners bound with two staples. 96 pages, each with 8 faint, light blue, vertical lines. Handwriting in ink and indelible pencil is across the lines.The front cover of the Notebook (now the back cover of the diary) is annotated as ‘Army Book 136A’, effaced with an imperial crown of the ‘St James’? Pattern with a title inscribed in an ellipse, which would once have read - SUPPLIED FOR THE USE OF OFFICERS AND NCOS.warrnambool, ww1 diary, mcdonald 3403, william donald mcdonald, william mcdonald, j a g brass, world war one

The Fred Rochow Railways Collection incorporates photos related to the operation of the Wodonga Railway Station including different types of trains and railways staff C. 1930 – 1990. It was donated to the Wodonga Historical Society by Fred Rochow, a railwayman who spent many years based in Wodonga. He joined the Victorian Railways on 17th June l947 and retired in 1988. For some time, he was a member of the Australian Federated Union of Locomotive Enginemen and served a term as a member of the Trades Hall Council. He had an extensive knowledge of the struggles that took place to achieve better conditions for railway workers. Fred worked for many years as a fireman and then worked his way up the ranks to driver, experiencing many changes from the days of steam locomotives through to diesel trains, locomotives and even the modern XPT train. He worked throughout Victoria at different stages of his career, with his final working years focused on the northeast of Victoria and the Albury to Melbourne line. After his retirement, Fred continued to share his love of steam miniature trains with the community.This collection has local and statewide significance as it captures images of trains, locomotives and personnel who operated the railway services in Wodonga and throughout Northeast Victoria. The railways played a critical role in opening up Victoria and connecting Australia for trade, business, social communication and transport.George Lynch standing alongside a DD Locomotive. This locomotive is fitted with two C-Class compressors used for testing air brakes on the extended length of a train. The DD Class locomotives entered service in 1902 as a new express passenger and mixed traffic steam locomotive class. They were the most numerous locomotive class on the Victorian Railways, with a total of 261 DD locomotives built. Originally introduced on mainline express passenger services, they were quickly superseded by the much larger A class and were relegated to secondary and branch line passenger and goods service, where they gave excellent service for the next 50 years. With some modifications made to the original design, the DD class locomotives ran on railways throughout Victoria until 1974railways wodonga, fred rochow, wodonga railwaymen, george lynch, dd class locomotives

This item is part of a group of five green display boards with photographs of sheep. This item is associated with the New South Wales Graziers Association world tour of merino sheep 1928/9.Five black and white photographs and printed paper mounted on green display board. Photographs depict sheep and men. The display board has pin holes in each corner.Front: [handwritten] Reversed Badgerface Pattern. / [printed] This is a remarkable instance of a reversal of pattern. The areas / that are black in the badgerface are white in this type, and vice versa. / This pattern behaves as a simple recessive to white and to badgerface / pattern. As in the badgerface, there are many modifications. Figs. / 1-3 show the typical pattern. Fig. 4 shows the head of another sheep / and Figs. 5-6 a typical lamb. Back: [handwritten] Reversed / Badgerface Pattern / 8 / [printed] PHOTOGRAPH COPYRIGHT / BY / THE ANIMAL BREEDING RESEARCH DEPT., / THE UNIVERSITY, EDINBURGH. / PLEASE RETURN TO :new south wales graziers association, world tour, england, sheep, farm, rural, agriculture, scotland

The Fred Rochow Railways Collection incorporates photos related to the operation of the Wodonga Railway Station including different types of trains and railways staff C. 1930 – 1990. It was donated to the Wodonga Historical Society by Fred Rochow, a railwayman who spent many years based in Wodonga. He joined the Victorian Railways on 17th June l947 and retired in 1988. For some time, he was a member of the Australian Federated Union of Locomotive Enginemen and served a term as a member of the Trades Hall Council. He had an extensive knowledge of the struggles that took place to achieve better conditions for railway workers. Fred worked for many years as a fireman and then worked his way up the ranks to driver, experiencing many changes from the days of steam locomotives through to diesel trains, locomotives and even the modern XPT train. He worked throughout Victoria at different stages of his career, with his final working years focused on the northeast of Victoria and the Albury to Melbourne line. After his retirement, Fred continued to share his love of steam miniature trains with the community.This collection has local and statewide significance as it captures images of trains, locomotives and personnel who operated the railway services in Wodonga and throughout Northeast Victoria. The railways played a critical role in opening up Victoria and connecting Australia for trade, business, social communication and transport.Left to right: W. Orchard, Hec Lloyd, Jack Hinchcliffe, Charlie Edmondson, George Lynch, Jack Bowden, Driver Tommy Black. "Edward Henty" Considered by many to be Victorian Railways' greatest passenger locomotives, the 4 S class steam locomotives were the first 3 cylinder steam locomotives. This small class was built to run the Melbourne to Albury passenger trains and spent their entire careers on the North East line. They were built unstreamlined and ran in this condition until 1937. The streamlining modifications complimented the all new "Spirit Of Progress" carriages. The S class ran the "Spirit" until 1952 at which time the newly delivered B class diesels took over. Locomotive S302 - the "Edward Henty" was withdrawn in July 1954, having covered 1,446,468 miles. On the locomotive in the background "EDWARD HENTY"railways wodonga, fred rochow, wodonga railwaymen, steam locomotive 302, edward henty

Copy of newspaper article (Jan. 1958): "Out of the Past" "The first post office at Eltham as it appeared in the eighties (sic). This photo was in the possession of the Burgoyne family, whose association with the Postal Department ended yesterday when the new post office was opened." The article indicates the photo is from the 1880s however it actually pre-dates the connection of the Electric Telegraph line in 1877 - most likely early 1870s. The Telegraph Office was opened Thursday, June 7, 1877 and the lines were connected to the building above the awning near where the lower corner of the large sign is. A similar image of the building dated circa 1888 (EDHS_00139) shows the telegraph line connection. The awning has also been updated with corrugated iron in lieu of bark shingles and the false facade above the awning removed. It is possible these modifications were made to the building at the time of the telegraph line connection. This photo forms part of a collection of photographs gathered by the Shire of Eltham for their centenary project book,"Pioneers and Painters: 100 years of the Shire of Eltham" by Alan Marshall (1971). The collection of over 500 images is held in partnership between Eltham District Historical Society and Yarra Plenty Regional Library (Eltham Library) and is now formally known as the 'The Shire of Eltham Pioneers Photograph Collection.' It is significant in being the first community sourced collection representing the places and people of the Shire's first one hundred years.Digital imagesepp, shire of eltham pioneers photograph collection, eltham, post office

The Let 13 Blanik was designed in 1956 by Karel Dlouhý of VZLÚ Letňany as a training glider. It filled that role very well and approximately 3000 have been built since production started in 1958. However, following a fatal accident involving a Blanik in Austria in 2010 that raised concerns about main spar metal fatigue, the type was grounded in Europe and America. In Australia, the extension of the life of this type of glider beyond 5000 hours / 18000 launches is dependent on compliance with directives for the inspection and modification of fatigue critical components. It is understood that VH-GAQ was built in 1971 and first registered on 14 August 1972. It is a Blanik that has been retired from service because of the metal fatigue concerns that apply to the type generally and the expense involved in complying with the applicable directives for on-going airworthiness certification. VH-GAQ was donated to the Australian Gliding Museum by the Australian Junior Gliding Club in 2010. Popular mass produced, metal, two seat sailplane. Used by many clubs in Australia in the 1970s. The Blanik VH-GAQ is a large two seat glider – sailplane of metal construction. It is finished in a white colour scheme with red detailing consisting of a red fuselage nose and adjoining red stripe along the fuselage sides to about midships. The control surfaces (ailerons, flaps, elevators and rudder) are covered with aircraft fabric and painted silver. The Perspex canopy fully encloses the cockpit which is fully equipped for dual flying. Registration VH-GAQ in black on sides of fuselage to the rearaustralian gliding, glider, sailplane, let kunovice, blanik

Lambert Ormsby was a New Zealand surgeon who migrated to Ireland. He described his inhaler in a letter to the Lancet in 1877.Ormsby listed the advantages of his inhaler as simple, inexpensive, small quantity required to produce sleep, prevents evaporation of ether, portable and small (can be carried in pocket), short time to complete anaesthesia (two minutes) and safe. Disadvantages of this apparatus were that it had to be removed in order to recharge the sponge with ether or when anaesthesia becomes too deep. Considerable carbon dioxide accumulation developed and there would also be some oxygen lack. In thirty years of use, Ormsby's Inhaler underwent certain modifications, an exhalation valve was fitted to the mask and device for recharging the sponge with ether was later added. The Ormsby inhaler was modified by Carter Braine in 1898 with the aim of making it easier to clean. Essentially it is very similar except there is no net around the bag.The inhaler consists of an india-rubber flexible bag enclosed within a net bag to limit expansion. There is a soft metallic mouthpiece with india-rubber tubing around the edge. The tubing had to be purchased separately from the manufacturer. The body contains a wire cage with a similarly shaped hollow sponge into which ether was poured.Maker's details inscribed into metal ring around the bore: Barth Co. London.ormsby, new zealand, carbon dioxide, carbon accumulation, carter braine, portable

non-fictionA booklet describing the history of the Hume Dam in question-and-answer format, illustrated by photographs from the Albury City Collection and other sources. This booklet was produced to accompany the exhibition "Turning the sod: building the Hume Dam", on display at Lavington Library from 21 December 2019 -1 March 2020." hume dam, dams -- new south wales, hume dam history, dams -- new south wales -- design and construction

The Pavillion was an extension to the Eltham Living and Learning Centre which was opened 8 October, 1994 In 1857, tanner John Pearson purchased three and a half acres of land in Little Eltham, at the western end of Pitt Street, with a 70-foot frontage to Maria Street (Main Road) and stretching down to the Diamond Creek for £100. He contracted Benjamin Oliver Wallis to build house for him. Wallis, a mason by trade who originated from the Cornish village of Newlyn, migrated to Melbourne in 1853 and was shortly engaged by Richard Warren to build the Eltham Hotel, which opened in 1854. When Warren fell into financial difficulty in 1858, Wallis purchased the hotel. That same year, Pearson constructed a tannery below the house with access to the water in the Diamond Creek. When Pearson became bankrupt in 1867, Wallis similarly acquired the house from Pearson’s creditors in 1868 and lived there until his death in 1896. For some of this time the house was in the name of Wallis’s son Richard but following his death in 1888, ownership reverted to his father. It was purchased by retired teacher Richard Gilsenen in 1899. Gilsenen was made acting head teacher at the Eltham State School in 1906 following the sudden death of head teacher John Brown. In the 1950s the house was bought by retired engineer Dr Alfred Fitzpatrick and his wife Claire who made various modifications to house goats and poultry as well as structural modifications to the house. In the early 1970s, Eltham Shire Councillors Frank Maas and Don Maling proposed an extended communities’ activities program be set up and the Commonwealth Grants Commission was approached for financial assistance. In 1974 a $50,000 Commonwealth Grant was received by the Shire Council to acquire the Fitzpatrick property as part of the planning to establish an extended communities’ activities program. The Fitzpatricks moved next door and Claire taught at the new Living and Learning Centre, which began in 1975, one of the first community education centres in Victoria.jim connor collection, eltham, eltham living and learning centre, living and learning centre, pavilion

Sixteen page book with brown paper covers in addition. Pages printed on art paper with a red overprint on some pages. Titled "Nachod Signals", published by the Nachod and United States Signal Co. Inc, successors to Nachod Signal Co of Louisville Kentucky. Has a list of dates on page 2, of patents, the last being 5/2/1918. Has on the bottom of most pages "Nachod Spells Safety" Details the Nachod signals system, type CD with the details of the operation, elements of the system, signal layout, installation and wiring, trolley Contactors, signal aspects, relays, assembly on poles, ordering information, fuses, special designs and modifications, information in ordering, quantity and list of material, and specification details of the Type P on the last three pages. See also Reg Item 3318 for another US company system, received by ESCo at the same time. Indicates that the Nachod and US Signal Company had merged.On top of page 1 "Ballarat Tramway Preservation Society Catalogue No. 3" in black ink and overstamped ESCO's date stamp of 4 Nov. 1926. On page 2 at bottom :"Nachod and United States Signal Co. Inc successors to" has been overstamped. trams, tramways, signals, railways, tramways

Report - carbon typed copy - 43 foolscap sheets bound within a brown card folder, stapled, with signs of an adhesive tape binding on the outside. Titled "Information - Tram 980 (PCC Equipment)", dated February 1964, prepared by the MMTB Engineering Department Testing Department Report No. I 5/1/144. Signed by W. Hines 6/2/64, report prepared by CLF. Provides a synopsis of the report, purpose of investigation, design, operational history, time in workshops, maintenance program, schedule speeds, riding qualities, has appendices with design modification, list of time in workshops, PCC tramcars maintenance program, workshops maintenance of ten typical trams, MMTB Tramcar Schedule speeds. Includes photographs of the failure of the main body transom and the replacement one, and two graphs. Second copy added 31-5-2016 from donation of Geoff Warburton. This copy - has red binding tape.trams, tramways, testing, pcc, preston workshops, reports, specification, tramcar manufacture, tramcar design, maintenance, tram 980

Located in High Street, Wodonga, this hotel underwent many modifications and name changes. It was built c1859 by James Bambrick close to the intended rail terminal in Huon Street. The site of the rail terminal actually changed but the name remained. James Bambrick served three terms as Wodonga Council president and was it was commonly referred to as “Bambrick’s Hotel”. It included 30 rooms as well as dining facilities. James Bambrick ran the hotel until 1902 when it was sold to J. Donnelly for £3,000. In 1912, whilst operated by T. J. Weller, the residential section of the hotel was almost completely destroyed by fire but only the ceiling of the bar was damaged and it continued to operate. Over the ensuing years the licensee changed hands frequently. By 1952, John Perry, owner of the “Stump” Junction Hotel also had the freehold of the Railway Hotel At some stage in the mid 1980’s the hotel was renamed as the “Murray River Hotel”, but still displayed the sign of the Railway Hotel. In 2009, it was closed for a short time whilst renovations took place to convert it into O’Maille’s Irish Hotel. It was demolished in 2020. These images document changes to an important local building first established c1868. It was an important meeting place and also the location of the earliest Council meetings in Wodonga.A set of photos both black and white and colour depicting changes to the Railway Hotel, Wodonga over timeA variety of names and advertising signsjames bambrick wodonga, bambrick's hotel, railway hotel wodonga, murray river hotel wodonga, o'maille's hotel,

Yellow fire fighter helmet with blue logo and orange fittings and reflecting tapeBROWN/Prosperity through service/ 11530/ Brown/ Fireman's helmet/3/Model Pro Helmets/ Size Date Batch (WGT 1215/ N.F.P.A. 1972/1985 Instructions to user : shell and liner constructed of fibreglass and polyethylene lining helmet can be seriously damaged by substances such as petrol, paint, adhesives or cleaning agents. Make no modifications. Fasten helmet securely. If helmet experiences a severe blow return it to the manufacturer for inspection or destroy and replace it. WARNING: no helmet can protect the wearer from all injuries. The manufacturer accepts no liability for injuries resulting from or during the use of this helmet/ MANUFACTURED BY PACIFIC HELMETS (NZ) LTD. WANGANUI. NEW ZEALAND.

Dr. Curt Schimmelbusch (1860-1895), a German physician, designed his original mask around 1889 while an assistant surgeon. Surgical assistants were often assigned the task of delivering the anesthetic. During anesthesia it was not uncommon for ether and chloroform to get onto the patient’s skin, causing irritation. Chloroform can even cause burn-like reactions. Schimmelbusch designed the rim of his mask so that both sides curve away from the patient’s face to form a kind of trough. He intended the trough-like rim to collect excess anesthetic that would otherwise have trickled onto the patient’s face. To anesthetize a patient, gauze was stretched over the metal bars and fastened in place by the hinge. The mask was placed over the patient’s nose and mouth, and the anesthetic was applied in drops or lightly poured onto the gauze so that the patient breathed in evaporated anesthetic as well as air. This type of mask is sometimes still used today for ether anesthesia in developing countries when other means are not available. (Wood Library Museum of Anesthesiology) This particular object is a modified version of Schimmelbusch's design, known as Chadborn's modification.Oval shaped chromium plated mask with two metal strips linked front to back and side to side to create a dome. An oval shaped mobile wire frame is attached to the lower part of the mask by a hinge at the back, approximately two inches from the lip of the metal handle. A "U" shaped bit of metal is attached to the front of the mask which acts as a clip to fasten the wire frame to the lower section of the mask.anaesthesia

This Minnitt machine was owned by Dr Mary Clementina DeGaris. Dr DeGaris qualified from medicine, MB BS, at the University of Melbourne in 1905. She continued her studies, becoming only the second woman in Victoria to qualify MD, in 1907. With the outbreak of war, DeGaris attempted to enlist as a doctor with the Australian Army but was refused. Undeterred she travelled to England, where she joined the Scottish Women's Hospitals for Foreign Service, a medical group made up entirely of women. After the war, she returned to Australia and set up practice as an obstetrician in Geelong, Victoria. Subsequently, the Geelong Hospital named a wing after her, "DeGaris House", which is now part of Geelong Private Hospital. DeGaris was awarded the St Saba medal, 3rd class, for her work during WWI. Robert James Minnitt introduced the concept of self-administered analgesia, using an apparatus designed and built in conjunction with London scientific instrument-maker, Charles King. The Minnitt apparatus met with considerable success and led to further modifications, including the introduction of the Queen Charlotte gas-air analgesia apparatus in 1936.Brown leather suitcase with brass locks and leather handle. Inside the case is metal equipment, with arms for attaching cylinders. On top of the case, located underneath the handle, is a small brass plate, bearing the name of the owner in black printed script on a piece of card or paper held inside the plate.Printed in black ink on name plate: Dr Mary C. De Garis.minnitt, geelong, scottish women's hospitals, world war i, obstetrician

19 NQ - Pulpwood Truck Untrafficable NQ Pulpwood wagon. In the 1950s, NQR 19 was modified by the removal of its sides and ends and the installation of intermediate upright staunchions to carry pulp-wood on the Beech Forest line. This modification was permanent and the vehicle became 19 NQ. 19 NQ - Service History 26/11/1898 NWS Built new NQ 19 was modified by having upright frames added to allow it to carry pulp-wood. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons In use 14 To be restored 6 *NQR 19.VA - 26/11/1898 NWS Built new - / /1926 - To NQ 19.VA - NQ 19.VA - /10/1958 NWS Modified To Pulpwood Carrier Only vehicle modified to this configuration Purchased by Puffing Billy Preservation Society. Sec 65/2711. RS 65/6012. "An NM (13) and pulpwood wagon .... for displayat Museum.....scrap value to be charged direct to the PBPS."Historic - Victorian Railways Narrow Gauge - Rolling Stock - Pulpwood wagon - Pulpwood Truck19 NQ - Pulpwood wagon - Pulpwood Truck made of Steel and metal 19 NQ puffing billy railway, pbr, rolling stock , 19 nq, pulpwood wagon - pulpwood truck, victorian railways, narrow gauge rolling stock

Grace Mitchell, a talented artist in later life and baker managed a pastry shop business near the corner of Mt Pleasant and Main Roads Eltham in the 1950’s. Shortly after her marriage to Arthur Mitchell in 1948 he had an accident that caused a head injury and was unable to work. Grace realised she needed to be home to care for her husband as well as earn an income. She managed the bureaucracy of council permits, made modifications to her home with savings to get the business off the ground without having to borrow money. Grace and Arthur were avid gardeners and would grow, wash and mince vegetables for pasties while Grace hand made and rolled the pastry. They cooked and minced their own meat for the pies and the fruit for the sweet pies came from their orchard at the rear of the property. She also baked scones and cakes. Grace operated her pastry shop for over 16 years. She supported the Shillinglaw Cottage Preservation Campaign to preserve the cottage through its Flavour of Eltham community cookbook published in 1964 and hosted cooking classes in the new Living and Learning Centre. Grace Mitchell passed away aged 95 years in 2011.Roll of 35mm colour negative film, 6 strips and associated colour print 10 x 15 cmFuji 100classes, eltham, living and learning centre, pottery class, eltham living and learning centre, grace mitchell, ursula dors, teaching, learning

The Fred Rochow Railways Collection incorporates photos related to the operation of the Wodonga Railway Station including different types of trains and railways staff C. 1930 – 1990. It was donated to the Wodonga Historical Society by Fred Rochow, a railwayman who spent many years based in Wodonga. He joined the Victorian Railways on 17th June l947 and retired in 1988. For some time, he was a member of the Australian Federated Union of Locomotive Enginemen and served a term as a member of the Trades Hall Council. He had an extensive knowledge of the struggles that took place to achieve better conditions for railway workers. Fred worked for many years as a fireman and then worked his way up the ranks to driver, experiencing many changes from the days of steam locomotives through to diesel trains, locomotives and even the modern XPT train. He worked throughout Victoria at different stages of his career, with his final working years focused on the northeast of Victoria and the Albury to Melbourne line. After his retirement, Fred continued to share his love of steam miniature trains with the community.This collection has local and statewide significance as it captures images of trains, locomotives and personnel who operated the railway services in Wodonga and throughout Northeast Victoria. The railways played a critical role in opening up Victoria and connecting Australia for trade, business, social communication and transport.Left to right: Jack Hinchcliffe, George Lynch, Bill Orchard, Hec Lloyd, ; BILL ROWE; Bill Rowe, Bill McLaren, Jack Dore, Jack Bowden, George Judge, Harry Alderson, Charlie Edmondson, Fireman Cyril Hughes. Cyril Hughes was born on 30 January 1903, started cleaning on 17 December 1924 and passed his Driving Qualifications on 27 June1941. "Sir Thomas Mitchell" Considered by many to be Victorian Railways' greatest passenger locomotives, the 4 S class steam locomotives were the first 3 cylinder steam locomotives. This small class was built to run the Melbourne to Albury passenger trains and spent their entire careers on the North East line. They were built unstreamlined and ran in this condition until 1937. The streamlining modifications complimented the all new "Spirit Of Progress" carriages. The S class ran the "Spirit" until 1952 at which time the newly delivered B class diesels took over. Locomotive S301 - the "Sir Thomas Mitchell" was withdrawn in October 1953, having covered 1,414,367 miles. On the locomotive in the background "SIR THOMAS MITCHELL"railways wodonga, fred rochow, wodonga railwaymen, steam locomotive s301, locomotive "sir thomas mitchell"