Acetylene lamp with metal base and white glass lampshadeRiemann DR.M.SCH - on upper body|Herm Reimann Chemnitz Gable N Zlighting, kerosene & oil

British Finger Lamp with dark blue glass base and handle. Mouth blown. Would have used kerosene. 1880- 1910.lighting, kerosene & oil

Oil lamp ornate metal base, green glass holder for oil.lighting, kerosene & oil

Guards lamp - of the type used by the Victorian Railways to give a green, red or clear or white signal while shunting or authorising trains to proceed. Used by station staff, shunters, guards and signal men.While not directly related to Ballarat tramways, of the type used by the Railways in the Ballarat district.Hand Lamp, Guards - Exterior casing of a black painted metal railway signal lamp with circular blue (for green colour) and red glass filters and a turning mechanism on the top under a circular handle. Includes the kerosene burner with wick and reflector plate. Item was specifically donated to the Museum by a member who died May 2022.railways, lamps, signals, guards

Prior to the launch of the motor powered Queenscliffe, three row boats were in service as lifeboats. This lantern was part of the equipment of the third lifeboat up to 1926.A brass lamp which was part of the safety equipment on board the Third Queenscliff LifeboatBrass Lantern with interchangeable port and starboard glass filters run of kerosene.Brandt Bros Melbourne Manufacturers 422 Elizabeth Streetlight, navigational safety

Purchased by Christian Ziebell on one of his two visits back to Germany.This object is of primary significance. Christian Ziebell brought it back from Germany on his return visit to Germany in 1856. It always hung where it is now and it is retractable to different heights. It hung on the lowest chain length over the table and was only raised when the family had festive events such as dances when Dorothea would accompany them on the piano. Great care had to be exercised when the lamp was raised because if it went up too high, and therefore became too close to the wooden ceiling, it could cause a fire. Francis Adams – son of Sylvia Adams (Ziebell) restored the lamp in the 1990’s.Original Miller hanging lamp, made of brass and opaque white glass. Lamp has chain-operated raising and lowering mechanism. Decorative brass trimming around widest edge of glass lampshade. Contains tubular wick.B & H Valpirfor written on lowering mechanism on top of the lamp. Rayo 24.98, PAT'D. NOV. 20.94, FEB 28.95, written on top of oil compartment.lighting, kerosene & oil, oil lamp, hanging lamp, original.

Table lamp with tubular wick, paraffin. Cast brass decorative base with four feet, cast brass interior and burner, with glass exterior and covering. Pink and white base colours on glass, with floral pattern printed on both sides of lamp. Cover a semi-circular shape with round neck opening on top.… Success…' (some words unreadable) embossed on burner platelighting, kerosene & oil, table lamp, brass, glass, paraffin, floral

Paraffin lamp. Dark wooden turned ornate stem. Metal base. Vitreous enamel fuel reservoir. Glass chimney with mantel. Plastic and cloth shade."Aladdin 21C Made in England GB. PAT. NOS. 694273-4 21C11" imprinted on fuel reservoir. "Aladdin heat resistant glass" imprinted on chimney. " Remove this gallery when lighting REG. TM. Aladdin Made in England" Written on gallery (under chimney)lighting, kerosene & oil, aladdin, kitchen lamp, light, paraffin, mantel, table lamp, chimney, lamp shade.

Paraffin lamp with clear glass oil reservoir and stand. Oil reservoir is spherical in shape and has a bird pattern embossed while stand has a fluted base with decorative rivets and turns. On top of oil reservoir is a brass wick holder. It seems to be missing the chimney."An Qing China" is imprinted on interior of base along with an "A" in a circle. Chinese characters/letters are also imprinted on base interior and can be translated to the same as the English.lighting, kerosene & oil, light, lamp, paraffin, oil, birds, glass.

A small number of heavy cast iron weights and two rods remain at the Point Hicks Lightstation. These weights comprise one rod with a forked top and four circular weights attached to the bottom of the shaft. The weights and rods were part of the original clockwork mechanism that was fitted beneath the lens to keep the kerosene‐fuelled light turning. They were attached to a cable or chains and moved vertically in similar fashion to the way weights move on grandfather clocks. As the weight fell, the optic clock was driven and the lens was turned. To keep the clock turning, the weight needed to be wound back up to the top of its travel. The cables and weights in this lighthouse were visible as they moved through the length of the tower up to the lantern room. It was usual for systems to move inside a tube extending up to the top, but in this case the tower’s cast iron spiral staircase, which is supported on cantilever cast iron brackets set into the concrete wall, spiralled around the space in which they moved. Lighthouse keepers had the arduous job of having to constantly wind the clock to keep the light active, and at least two keepers needed to observe a strict roster of hours. When electric motors were invented, all of this became redundant and the motors were able to turn the optic for as long as there was power to drive them. In December 1964, the original 1890 Chance Bros kerosene‐fuelled light and clockwork mechanism were replaced by small electric motor, and the number of keepers reduced to two. The six circular weights and rods originate from the obsolete system and may have been part of a larger set. Wilsons Promontory retains seven of its original set of ten weights, all of which are detached from the tower’s weight tube. Cape Schanck has a set of fourteen weights remaining in situ as well as another four detached weights, which have inscriptions. One weight is displayed in the lantern room at Cape Otway. The image shows four of the clockwork weights attached to a rod with a forked top. They were part of the original clockwork mechanism that was fitted beneath the lens to keep the kerosene‐fuelled light turning. The Aldis lamp in its case sits on the floor next to the weights. Source: Parks Victoria.The Point Hicks weights have first level contributory significance for the insights they provide into the superseded technology and operations of a late nineteenth century lighthouse. They are well provenanced and are significant for their historic value as part of the lightstation’s Chance Brothers optical system installed in 1890. Four circular metal weights are stored on a metal rod with a forked section at the top. The weights have a cut out section which allows the weights to be removed easily.

Was the stand for a Chance Brothers air & oil containers fitted with pump handle & pressure gauges.This type of installation was once common and relied on the lightkeeper having to pressurise the cylinders manually at regular intervals throughout the hours of darkness. The oil was fed under pressure to the burner mantle. It is all that remains of an air and kerosene oil tank installation, with each rounded side formerly supporting a heavy iron tank. The containers would have been fitted with a pump handle and pressure gauges. An intact assemblage is displayed in the AMSA offices, Canberra with a text that explains ‘This type of installation was once common and relied on the lightkeeper having to pressurise the cylinders manually at regular intervals throughout the hours of darkness’.The system involved vaporising kerosene under pressure and mixing it with air and then burning the vapour to heat an incandescent mantle. The use of kerosene as a fuel to light the lantern became the most common system of illumination from the 1860s after the oil industry in the United States began to develop. The kerosene vapour burner was created in 1901 by British inventor Arthur Kitson (1859-1937) and perfected by Chance Bros for burning a more intense light in their renowned lenses. The lamp had to be watched throughout the night in case a mantle broke, and the tanks needed to be maintained by hand-pumping each hour or so. The Point Hicks lantern was initially lit by a six-wick Trinity house kerosene burner. This was replaced by the more efficient and brighter 55mm vaporised kerosene mantle burner in 1905, and the tank stand is probably original to this apparatus. Electricity eventually replaced kerosene at Point Hicks in 1964 making the tank installation obsolete, and the last kerosene system in an Australian lighthouse was replaced in 1985. Gabo Island Lightstation has a pair of tanks that are not attached to the optical system and are no longer in the lighthouse. They are also missing the pressure gauges that were formerly attached to the top of each cylinder. An intact tank assemblage is displayed at the Cape Schanck Lighthouse Museum it is detached and not original to the lighthouse. Although corroded, the remnant Point Hicks tank stand has first level contributory importance to the lightstation. It is significant for its provenance and historical value as part of the Chance Bros vaporised kerosene burner introduced in 1905 to intensify the light and improve the efficiency of the system. The rusted iron stand rests on four short legs and is shaped like a pair of spectacles.

Tilley lamp Model x 246. Complete Mantel broken, black top, silver base, pump action, and with handlekerosene lamps

These types of metal and glass railway signalling lamps were used for communication, safety and lighting by train guards, shunters and signalmen, as well as station staff in the late 1880s to the early 1900s. They were hand operated and used fuel such as kerosene.The three railway signalling lamps have local significance as a set donated by a resident of Wodonga who worked for the Victorian Railways, as well as national significance as examples of the communication and safety equipment used by the railways in Australia in the late 19th century and early 20th century.Set of three painted black metal and glass railway signal lamps used for various purposes during train journeys. The largest signal lamp has circular blue and red glass filters and a turning mechanism on the top under the handle. "A y" on a small copper plate on one side of the largest signal lamp - Lamp 1.railway lamps, signalling lamp, train signal lamps

Metal and glass railway signalling lamps were used for communication, safety and lighting by train guards, shunters and signalmen, as well as station staff in the late 1880s to the early 1900s. They were hand operated and used fuel such as kerosene.The railway signal lamp has local significance as part of a set of three lamps donated by a resident of Wodonga who worked for the Victorian Railways. It also has national significance as an example of communication and safety equipment used by the railways in Australia in the late 19th century and early 20th century.Exterior casing of a black painted metal railway signal lamp with circular blue and red glass filters and a turning mechanism on the top under a circular handle. Small copper plate with the letters "A y" stamped on it, on one side of the lamp. "A y"railway lamps, signalling lamp, train signal lamps

Metal and glass railway signalling lamps were used for communication, safety and lighting by train guards, shunters and signalmen, as well as station staff in the late 1880s to the early 1900s. They were hand operated and used fuel such as kerosene.The railway signal lamp has local significance as part of a set of three lamps donated by a resident of Wodonga who worked for the Victorian Railways. It also has national significance as an example of communication and safety equipment used by the railways in Australia in the late 19th century and early 20th century.Black painted metal signal lamp with a circular metal cover over a clear glass disk at the front and an elongated oval shaped handle at the back. The circular metal cover has a vertical slit in it. There is an inscription on the top of the lamp with the date 1917 and the company name "Eli Griffiths & Sons, Birmingham"."ELI GRIFFITHS & SONS / 1917 / BIRMINGHAM"railway lamps, signalling lamp, train signal lamps, railway equipment

These types of metal and glass railway signal lamps were used for communication, safety and lighting by train guards, shunters and signalmen, as well as station staff in the late 1880s to the early 1900s. They were hand operated and used fuel such as kerosene.The railway signal lamp has local significance as part of a set of three lamps donated by a resident of Wodonga who worked for the Victorian Railways. It also has national significance as an example of communication and safety equipment used by the railways in Australia in the late 19th century and early 20th century.Black painted metal signal lamp with a clear glass lens secured at the front and one thin elongated oval shaped handle showing at the back. The metal appears to be tin plated iron under the black paint layer. There is an oval plate with an embossed inscription on the proper left side of the lamp that is partly covered by the door at the front which holds the clear glass lens. The inscription includes the date 1901."...NARIPPINGILLE STOVE / CO LTD 1901 / PATENT...S & / ...NUFACTURERS / RMINGHAM" on an oval shaped plate on the proper left side, which is partly covered by the door with the clear glass lens.railways wodonga, victorian railways

The kerosene container is documeted as having been used to fill slush lamps, hand lamps and train engine lights, and is part of the Wodonga Historical Society's railways collection.The kerosene container has local significance as it was donated by a Wodonga resident and is part of Wodonga Historical Society's railways collection. It is documented as having been used to fill slush lamps, hand lamps and train engine lights. Grey metal kerosene container with a looped handle attached to the sides, as well as a handle on the back of the container with a metal chain attached to it to secure the cap for the container. Used to fill slush lamps, hand lamps and train engine lights.kerosene container, kerosene bottle, fuel for railway lamps

This book documents the development of manufactured goods available in Australia over the period 1880 to 1940. This was the period between the end of the gold rushes and the Second World War. It consists of 224 pages including explanatory text, illustrations and a bibliography.Manufactured goods available in Australia over the period 1880 to 1940 underwent massive change. Australia moved from long skirts to shorter styles, from kerosene lamps to electric lights, from horse drawn vehicles to cars and aeroplanes. This collection reflects these changes in many aspects of people's life styles.manufactured goods australia 1880 - 1940, social life and customs, australian shopping directories

Steel framed paraffin lamp with steel base. Glass bulbous chimney with embossed writing and makers mark. Thin steel wire for protecting glass, and as handle on top with hook indent, attached to frame. Mechanism for raising and lowering glass casing by small handle attached to frame for facilitating lighting. Wick trimming device on side of base, and cap covering hole in base for filling.On glass - 'Feuerhand, Made in Germany' embossed. On opposite side, company logo of hand holding flames. On base - 'Made in Germany', embossed. Company logo. '*Nr. 327' Company logo on oil cap, wick trimming knob and on top of framelighting, kerosene and oil, hurricane, lamp, paraffin, feuerhand, lighting. dora buckley

This is a typical example of a flat wick domestic paraffin lamp used in households prior to the introduction of electricity.A flat-wick lamp is a simple type of paraffin lamp, which burns paraffin drawn up through a wick by capillary action. A flat-wick lamp has a fuel tank (fount), with the lamp burner attached. Attached to the fuel tank, four prongs hold the glass chimney, which acts to prevent the flame from being blown out and enhances a thermally induced draft. The glass chimney needs a "throat", or slight constriction, to create the proper draft for complete combustion of the fuel; the draft carries more air (oxygen) past the flame, helping to produce a smokeless light, which is brighter than an open flame would produce. The wick holder has holes around the outer edges. When the lantern is lit and a chimney is attached, the thermally induced draft draws air through these holes and passes over the top of the wick. This has a cooling effect and keeps the wick from over heating. The lamp burner has a flat wick, made of cotton. The lower part of the wick dips into the fount and absorbs the paraffin; the top part of the wick extends out of the wick tube of the lamp burner, which includes a wick-adjustment mechanism. Adjusting how much of the wick extends above the wick tube controls the flame. The wick tube surrounds the wick and ensures that the correct amount of air reaches the lamp burner. Adjustment is usually done by means of a small knob operating a cric, which is a toothed metal sprocket bearing against the wick. If the wick is too high, and extends beyond the burner cone at the top of the wick tube, the lamp will produce smoke and soot (unburned carbon). When the lamp is lit, the paraffin that the wick has absorbed burns and produces a clear, bright, yellow flame. As the paraffin burns, capillary action in the wick draws more kerosene up from the fuel tank. All paraffin flat-wick lamps use the dead-flame burner design, where the flame is fed cold air from below, and hot air exits above. (Source: Wikipedia accessed 24 Nov 2023) This lantern has a circular heavy green glass base for holding the paraffin. The base has a 12mm green glass handle. There is a small clear glass chimney with a fluted upper edge and some bubbles in the glass. The metal burner and wick holder has four metal prongs to hold the glass chimney in place. The round metal wick winder is functioning. There is a small amount of residual paraffin in the base. The flat wick is made of cotton.There are no markings to indicate the manufacturer.paraffin lamp, flat wick lamp, domestic lantern