Part of the G. Hadden collection which is a textbook for candidates for the under managers cert."Winning and Working" is the name of this book which is a hard bound book with a black cover with gold lettering and 525 pages.Inside the front cover of the book is the name "G. Hadden Private".

A. Part of thet G. Hadden colletion. B. Describes mining arithmitic and mining ventilation theory for mining students.A. Tate's Mining B. Hard Bound, Red Cover, Gold Lettering with 96 pages.Inside front cover: "G. Hadden Broome Cres Wonthaggi"

A. Part of the George Hadden collection B.Descibes in detail all aspects of mine surveying"A treatise on mine surveying" Hard Bound, red cover, gold lettering, 372 pages plus a 60 page advertising supplement.Inside front cover: "A.Blackburn Shottou Colliery Co. Durham.", "G.Hadden"

A. Part of the G.Hadden Collection. B. Describes all types of mining machinery"Mining Machinery" Hard Bound, gold lettering, 378 pages.Inside front cover "G.Hadden Private", "10/-"

Used at State Coal Mine to oil equipmentTin oil can with a long spout and top and rear handle

Used by miners as identification disc.Small brass disc with number stamped on, two holes near top edge, brass chain attached.1758

Small brass disk with a number stamped on. Two holes near top edge."1089"

Owned by General Manager J. McLeish.Stained beige cover. Inscription title in black. 327 pages. Titled "Transcriptions of the Australasian Institute of Mining Engineers Vol XIV".On cover " Australasian Institute of Mining Engineers". On spine " Transcriptions Australasian Institute of Mining Engineers Vol XIV".

Key that opened the gates to No. 20 shaft.Key on metal chain. Chain is attached to a large metal tag.on tag: 20 shaft gates. on key: R 62, Dalson (7V) Melb. Aust.

Booklet of "Daily Inspection" report sheets, serrated edge. Green cardboard cover, stapled spine covered in grey binding tape.

Notebook used to record bags of horse feed at the different mine areas.Dirty brown cardboard cover, grey binding tape on spine. Black text on front cover.Victorian Railways. Notebook 1875-49

Skip token used by miners to identify which skips they had filled.Small brass rectangle with one curved end. Small hole through left-hand side."19"

Skip token used by miners to identify which skips they had filled.833.1, 833.2: small brass diamond with rope attached through a hole in the top corner."5"

Skip token used by miners to identify which skips they had filled.Small brass diamond with rope attached through a hole in the top corner."18"

Used by miners at SCM to test for gas.Davey Safety Lampon side: EP 82

Used for first aid in SCMBlack first aid box with a red cross on the lid. Still has first aid contents inside

Railway luggage ticket to ensure that luggage reaches its destination which is the State Coal Mine.Small used railway luggage ticket with inscriptions.Yes

Booklet about the Edison Model J Miners Electric Safety Cap Lamp. Small booklet with black and blue text, appears to be the manual for the lamp (SCM 0004)

Nobby Smith's bag used when out riding his horse fixing fences. Made by Arthur Smales. Nobby Smith worked for almost 30 years at the SCM as a Stable Manager. "Come here! Gee off" Joe & Lyn Chambers December 1991Leather bag / satchel with flap and buckle, long shoulder strap. Side panel stiched with white stitching.

Shower rose from Kirrak Area change rooms.Steel cylinder with small opening at the top

Block and tackle hook with frame for two pulleys. (pulleys missing) hook rotates in metal pin (as designed), but metal pin rusted into frame; surface rust all over. Composed of three sheets of steel connected by belts to hook.

Wooden pattern used to make impression in sand to form mold for casting hot metal. These patterns were for the caps for bearing covers.Wood, with an oval footprint. Pins underneath with covered channel across oval, cylindrical cap mounted on top of channel, semi-circular (approx) flanges either side of channel cover.

Wood, cylindrical base, curved narrowing neck, sperical (approx) top; nail hammered diagionally through top.

Two slightly different wooden patterns for casting unknown item. (approx.) Rectangular piece of wood with a narrower piece affixed across top ( long side of rectangle); narrow piece has two curved 'wedges' attached (one loose).

It is unknown what this item was a pattern for.One flat piece of rectangular wood with a hole on the top - center and two nails, one at the top left corner, one at the bottom - RH corner. A second piece of wood is attached on top of the first; it is smaller in width and split exactly in two. There is a design cut out of second piece in shape of a pear. Bulbous part of design is centered around a hole in the first piece of wood. Three nails protrude from the second piece of wood. Three nails in the second piece of wood are located; one in each section of the more bulbous end of cut-out, & third on one section of the smaller end of cut-out. Hole on bottom of wood does not go all of the way through.

This is a pattern for the stove front for the oat kiln at the mill.Rectangular piece of wood, broken at one end with two full cutouts and part of third. One, and the part of another cut-out is high arches. Frame, missing in places, running along outer rim and along cut-outs. Two rows of nails run down between arches holding braces in palce on back.

Augers were used in processing the grain, however this wooden auger is possibly a pattern for a cast metal auger.A long piece of hexagonal wood with a descending spiral of square wooden blades. On the top it has a circular piece of wood

Used to make cast for the metal ring gear for the water wheel which powered the Mill.Slightly arched wooden pattern with wooden ridges along the edge. Three square metal plates with a hole in the centre, bolted on with four bolts. Ten pentagin pieces of wood attached to the face.

Used as pattern to cast crown wheel of drive on water wheel. Actual drive has since been sold, only mold remainsCircular wooden pattern, raised centre circular area surrounded by four wide, flat spokes at regular intervals (the interim spaces being cut out with rounded corners) which are in turn surrounded by a rim which tapers back from the centre of the piece and has fixed to it regularly interleaved slats. Slats of protruding oblongs tapered from attachment to top and also central end to outer point. Light coloured wood 1 & 2 are Broken off pieces of back.

Probably used to drive machinery as part of milling process.From left to right along long centre pole (horizontal) is a small wide wheel, on a narrow arched stand.At the centre of the pole is a larger, slimmer wheel followed by a smaller wheel.