Instruction - 24 pages, with two punch holes and stapled on the left hand side titled "Air Brake Safety Car Control Equipment" number 84450.1B, pages 3 to 26. Details the M28 brake valve, sanding features, operation, door and step controllers, check valve, CP-25C air compressor, brake valves, air compressor governors, drawings of piping, maintenance, testing, faults and general operation. See Reg Item. 3478 for another similar document. No details as to who published it or dates.trams, tramways, electrical engineering, electrical equipment, air compressors, brakes, instructions, maintenance, controllers

.1 - Instruction - approx. 50 pages, A4 pages with some foolscap pages detailing the: "Wheel diameter compensator - Kit Details and installation instructions", prepared by the Metropolitan Transit Authority for Manager Preston Workshop by the Manager electrical design and communications branch - P. CussZ. Dated July 1984 for fitting to Z1 and Z2 trams. Includes an "Owners' Manual" in a plastic folder, prepared by Selectronic Components of Bayswater. .2 -set of 3 drawings showing the layout for the circuit boards prepared by Precision Engineering dated 29-8-1991, in a labelled plastic folder.trams, tramways, z class, maintenance, electrical engineering, electrical equipment, wheels, the met, tram 980

Drawing shows the power supply arrangement to the overhead for the VR St Kilda Brighton tramway, including Elwood depot and substation. Has been marked up for removal of the line south of Elwood Depot to Brighton and Dickens St crossover. Shows the isolating and paralleling switches and their pole numbers. Not known when the original drawing was prepared. The tramway or electric street raikway operated from 1906 to 1959, the section south of Elwood depot closing in two stages during 1956. See reference for history of the line.Yields information about the power supply arrangements for the St Kilda Brighton tramway.Drawing dyeline print and hand coloured with a cloth back sheet with two punch holes on the left hand side to enable filing.Has numerous pencil inscriptions that updated the drawing to c1957 and a "Cancelled" stamp in the bottom right hand corner.tramways, vr, victorian railways, power supply, electrical switching, electrical engineering, st kilda brighton tramway, elwood depot

The document provides cross sections of track used from c1920 to 1928. The folder is marked "H Bell" most likely the son of the later Chairman, Mr Hector Bell who was a civil engineer with the MMTB. 1 - P3948 - Camberwell Road - 1926 2 - P2789 - Camberwell Road reconstruction - 1920 3 - P3753 - Chapel St - 1926 4 - P60 - Expansion joints Church St bridge - 1924 5 - P3686 - Commercial Road reconstruction - 1926 6 - P4024 - Cotham Road reconstruction - 1927 7 - P4699 - Droop St duplication - 1927 8 - P2384 - Flemington Road conversion - 1925 9 - P1187 - Flemington Road tramway - undated c1920 10 - P4131 - Flinders St conversion - 1927 11 - P4132 - Flinders St conversion - special track drains where subject to flooding - 1927 12 - P3603 - Glenferrie Road east track - 1926 13 - P2608 - Glenferrie Road reconstruction - 1925 14 - P3577 - Glen Huntly Road extension - 1926 15 - P3745 - Glen Huntly Rd duplication - 1926 16 - P4655 - Gilbert Rd duplication - 1928 17 - P2472 - Hannah St at Crossings 1925 18 - P2459 - Hannah St in plantations - 1925 19 - P2582 - High St Prahran reconstruction - 1926 20 - P1594 - High St Prahran reconstruction - 1925 21 - P3611 - High St Malvern reconstruction - 1926 22 - P3900 - Lygon St - 1926 23 - P3689 - Malvern Road reconstruction - 1926 24 - P3951 - West Coburg Route - sleeper spacing - 1926 25 - P4703 - Nicholson St Coburg - duplication - 1928 26 - P4470 - Norwood Road duplication - 1927 27 - P2473 - Park St tramway - 1925 28 - P3707 - Riversdale Road reconstruction - 1926 29 - P4630 - Riversdale Road extension - 1927 30 - P4497- Riversdale Road duplication - 1927 31 - P1387 - South Melbourne Road - special boxed in Construction for Albert Road (parking loop) - 1924 32 - P4691 - Swan St reconstruction - 1927 33 - P3640 - Victoria St part - 1926 (2 copies) 34 - P4522 - Wallen Road reconstruction - 1927 35 - P3939 - Wallen Road reconstruction in front of depot - 1927 36 - P4702 - Trial types of track - 1928 37 - P4254 - Wattletree Road reconstruction - 1927 38 - P4531 - Wattletree Road connection to Glenferrie Road - 1927 39 - P4708 - Wellington Rd siding - 1928Yields information about the various tramway track cross sections used by the MMTB including cable tram conversions.Folder - heavy card cloth covers fitted with two interscrews containing some 39 plus one duplicate folded blue prints. Covers made by Swinnerton Bros of Melbourne - see image 6 for their logo/trademark.Has "H Bell" in ink on rear cover.tramways, mmtb, tram tracks, rails, civil engineering, cable conversion, new tramways

Black and white photographs - 2 copiesTyped below photograph, "Boiler explosion at Ringwood station 20/6/1894. Heard in Box Hill". Article from newspapers:- Weekly Times (Melbourne, Vic. : 1869 - 1954), Saturday 27 January 1894, page 21 Official enquiry. The Board of Enquiry appointed by the Railway Commissioners to enquire into the causes of the boiler explosion which shattered the locomotive at Ringwood on Saturday night, assembled at the Railway department on Wednesday to commence its deliberations, The board consisted of Mr R. Fulton, engineer, C. W. McLean; engineer to the Marine Board, and Mr Mephan Ferguson, iron-founder. There is some difficulty at the outset about the constitution of the board; It was suggested that the Apt of Parliament contemplated that boards of experts, after the manner of the present one, needed, to have their appointments confirmed by the Governor-in-Council. The point, however, was not considered sufficiently important to prevent the board from proceeding with evidence. Robert Greyford, stationmaster at Ringwood, was the first witness. He said he saw the explosion on Saturday night at about twenty minutes to 8. There was a rush to the engine to see what had happened, and the driver and fireman were both found on the platform of the engine. The driver seemed badly hurt, but the fireman, to all appearances, was not so badly injured. They were both attended to and sent up to Melbourne by the last suburban train. Witness had a look at the engine and found the dome and all the plates round the boiler blown clean, away. The springs were also blown clean away. The Chairman (Mr Fulton) : Did you measure the distance ? Witness: Yes; one of the plates was 209 yards away. A piece from the top of the boiler 15 pounds in weight he found driven into the hard beaten track 410 yards away. Several pieces of boiler plate were found scattered at various distances. The buildings roundabout were injured. The Chairman; Did you notice anything peculiar about either of the driver or the fireman ? — No ; nothing wrong, with either of them. If the engine was blowing off at all, it must have been very light. In your opinion, were they perfectly sober ? — Perfectly. In approaching the station, is there a down or an up grade? — A very slight down grade. How is the road from Healesville ? — Up and down all the way. It is down, grade for about 200 yards coming into Ringwood station. They shut off ; steam about a quarter of a mile away, and come in at a good pace. They generally put on 15 pounds of steam while they are in the station. Mr Ferguson : Had the driver the usual load on ? — Yes ; about the usual load. Witness added that he had known the driver personally for about 10 years, and he had always been a careful, steady, sober man. He did not know the fireman so well. John Palmer, porter at Ringwood station, also saw the explosion. He was attending to the train on its arrival. He was knocked down by the force of the explosion. When he got up he saw the engine driver being carried into the office covered in blood. He noticed nothing peculiar about the driver and fireman, nor about the engine. Mr McLean : How far were you from the engine when you were knocked down ? — From ten to fifteen yards. William Paul, the guard of the train to which the injured locomotive Was attached, said he was looking at the engine at the very moment the explosion occurred. It seemed to come from exactly under the dome. The force of it took him off his feet. He was about 15 yards from the tender. When he rose he tried to reach the engine, but could not do so on account of the steam and coal dust. He called out to know whether any of the passengers were injured, and got no response, so that he concluded they were all right. All the lamps but about half dozen were extinguished by the force of the explosion, although the glass was not broken. He could testify most distinctly that the driver and fireman were both sober. The driver was a man who never drank. The steam started to blow off about a minute and a half before the explosion took place. The last place at which the engine took water was Healesville. The Chairman : Do yon know anything of the quality of the water there ? Is it creek water ? — Yes ; it comes from the Graceburn River. You never heard of its quality ?— No. How long have you known this engine on the road— About 13 months. Hew long have you known the driver on this line ? — About six weeks. I have known the fireman several years. The driver was a strict teetotaller, and I never saw the fireman take anything to drink in his life. Mr T. H, Woodroffe, chief mechanical engineer of the Victorian Railways, produced a report he had written to the secretary, about this explosion. The document gave facts concerning the engine and the explosion. It stated that the rapture seemed to have occurred at the rim of the plates adjoining the fire box. The engine was built at the Phoenix Foundry, Ballarat, in 1883. It was repaired at various times, the last time being in July of last year when it was sent to the Port Melbourne shops, and was then tested to a cold water pressure of 195 and found all right. It was the custom to overhaul all locomotives about every five years. The Chairman : There were no very heavy repairs in July, 1893; were there? — Not to the boilers. The shop manager's report says that the plug and safety tap holes were repaired, five new copper studs put in firebox, ash-pan door repaired, tender cleaned and overhauled, and studs re-rivetted, and boiler tested to pressure of 195, cold water. Mr Woodroffe read the report of the repairs effected to the boiler in December, 1888. That would be the time the plate was put in the boiler. On that occasion three new plates were put in the bottom and the boiler tested up to 195. The Chairman: Do you keep a record of the water used ?— Yes, the water in this case, I think, came from the Maroondah scheme. Mr Woodroffe said boilers were examined front time to time in the running sheds. In his opinion every possible care had been taken to keep the engine in proper care. There might, however, be lessons learnt from this. The Chairman: No doubt. From his examination of the plates [the] witness did not think the state of them could have been detected from the outside. There were no signs of leakage or sweating or anything of that sort. The next witness- was Walter Stinton, workshop manager at Newport and he said that the injured engine had been repeatedly repaired under his charge. He gave a technical account of the repairs effected on various occasions. The testing of locomotives was under his special notice. They had a high pressure pipe running; round the works, and a pump set at 2001b. When the boiler was pumped full of water the pressure when applied up to 1951b. The board appointed by the department to inquire into the Ringwood locomotive boiler explosion sat again at Spencer street on 25th inst. Mr R. Fulton presided and the other members of the board were. Mr Mephan Ferguson and Mr C. W. McLean. Charles Grubb, foreman of the boiler-makers at the Newport workshops, said he had inspected the pieces of plate that had been blown out of the engine, and after examining them, pointed out to the Chief Mechanical Engineer the portion where the plate had started to burst. It was under the lap, on the right hand side of the boiler. The grooving might be accounted for by bad water. During the past twenty years he had examined all the boilers that came into the Williamstown workshops, and while some were hardly marked at all, others were very badly eaten away. The practice was to cut out the defective portions. In this case the boiler was repaired in a similar manner. The Chairman : Can you suggest any other way of repairing so as to prevent accident ? — No, unless by taking out a plate on one side from the joint, and carrying it further up so as to avoid the joints meeting, or by taking out the plate altogether. What would.be the cost .of putting in a new " plate I—Perhaps about double the price; but I wouldn't recommend that course. It would be putting a new plate against plates that have been in use ten years or so and that would not be advisable. I think the present system better. I consider the present system of repairing the best. This is the first we have had so bad like that, to my knowledge. You attributed this to bad water. Is there no other probable cause ? — Well; unless the iron be bad. This was Lowmoor iron. I think this accident was caused by the eating away of plates. This one was the worst I have seen, for the short time it had been running. We use three classes of iron — Lowmoor, Monkbridge and Bowling. By Mr Woodroffe (Chief Mechanical Engineer) ; There are engines still running that were repaired at the same time as this one, in 1888, and. in the same way. These are engines 339 and 333. They have been recently examined and are in splendid order. What in your experience, is the age of a boiler on the Victorian railways? — From 17 to 20 years our earlier boilers stood. The later boilers don't stand so well. How is that? — There is difference in construction, and the material is lighter. The old boilers had thicker plates. Have you been asked in any way to curtail boiler affairs? — No, sir; nor in any way. You have never hesitated to carry out any necessary repairs? — Never. Our orders have been to exercise every care in examining, repairing and renewing boilers. Witness said that his practice was when an engine came into the workshop to find out how long she had been running. If over five years, he informed the workshop manager, and they thought it necessary the tubes were taken nut. If everything was in good order witness reported to the manager. The cost of taking out the tubes and putting them in again was about L20. Mr Woodroffe : Have you ever hesitated to repair a boiler on the score of expense ? — No, never. Mr McLean : Hew do yon ascertain whether a boiler requires repairs?— I keep a record of every boiler examined. From every boiler that comes in I have the dome covers taken off, and when it is practical I get inside. l can almost tell from the top of a boiler what the bottom is like. If there is any doubt about it I have the tubes taken out. If I have suspicion of defective plate I cause to have bored a triangle in the plate at the point where there is the most wear. There is a travelling inspector who visits all the running sheds of the colony except Port Melbourne and tests the boilers. He reports to us and we note what he points out. Alfred Thompson, locomotive inspector of the eastern section, said he knew this engine, 297R. He read a list of her repairs. He heard of the accident on Saturday night and went up to Ringwood. The Chairman : Did you ever notice anything peculiar about the engine? — No, I considered her A1 and would not have hesitated to have put on 140lb pressure owing to the repairs she had undergone. Witness considered that the explosion was caused by the expansion and contraction of the plates ; and, no doubt, the plate had been eaten away through bad water. The other side of the boiler showed: signs of corrosion: By Mr Woodroffe ; Is every care taken with the boilers ? — Yes, every possible care is taken for the safety of boilers, Weekly Times (Melbourne, Vic. : 1869 - 1954), Saturday 27 January 1894, page 7 EXPLOSION OF A LOCOMOTIVE BOILER, NARROW ESACPE FROM FATALITIES. THE DAMAGED ENGINE. [See drawing of loco – saved in “Railways” folder] The explosion of a locomotive boiler at Ringwood on Saturday evening, formed the subject of much discussion in railway circles on Monday. The Minister arrived at the office at an unusually early hour and immediately entered into a consultation with the acting chairman, Mr Kibble, and Mr Commissioner Murray. As the result of the interview it was resolved to ask three gentlemen of acknowledged engineering experience to sib as a board with the . object of inquiring into the cause of the accident and furnishing a report. Mr Richardson and the Commissioners are tally seized of the importance of having a searching investigation into the accident, and, with Mr Murray, the former went to Ringwood to inspect the scene of the disaster. They will he accompanied by Mr Woodroffe. During the morning no official report had come to hand from the driver or fireman of the engine in reference to the accident, but that is thought to be due to the circumstance that they have not sufficiently recovered to be able to give a circumstantial account of what occurred. The engine was one of the old R's, and, Mr Kibble pronounced them to be about the best class of engines used. So far nothing can be said as to the probable cause of the accident, as the broken plating of the engine has not been submitted to the inspection of experts. Weekly Times (Melbourne, Vic. : 1869 - 1954), Saturday 27 January 1894, page 7 STATEMENT BY THE FIREMAN. This morning Thomas Miles, fireman on the engine the boiler of which exploded on Saturday night, is suffering from an injury to the spine, as well as a very severe shaking to the system. He states that he was fireman on the engine attached to the train which left Healesville on Saturday evening, at ten minutes to 8. Everything went all right until Ringwood was reached, when, .just as the train was about to continue its journey, a load explosion took place and Miles remembers nothing more until he was picked np on the platform ; and found himself suffering from a pain in the back, and an injury to his arm. He cannot think of any reason which could have caused the explosion, as there was plenty of water in the boiler, and everything seemed working all right. Mr R. Fulton, consulting engineer, of Queen street; Mr McLean, a member of the Marine Board ; and Mr Mephan Ferguson, engineer, have consented to act as a board to inquire into the cause of the engine boiler explosion at Ringwood on Saturday evening. The board has been appointed under section 117 of Act 1135, which provides that the Governor-in-Council may direct the taking of a such a step. Mr1 Fulton will act as chairman of the board, which met for the first time at the railway offices, Spencer street, this forenoon. Before separating the members of the Board paid a visit to the Prince's Bridge locomotive sheds in company with Mr Woodroffe, the chief mechanical engineer, for the purpose of inspecting the shattered boiler. It has been stated that the explosion is known to have been caused by a flaw in a plate which was put on the boiler about four years ago, but enquiries have tailed to elicit anything in support of that view. The engineers connected with the department are not inclined to say anything on the subject. Weekly Times (Melbourne, Vic. : 1869 - 1954), Saturday 14 April 1894, page 20 The Ringwood Boiler Explosion, The Minister of Railways has received the supplementary report of the board appointed by him to investigate the circumstances connected with the explosion of a locomotive boiler at Ringwood. In their first report the board did not attach blame to anyone. Mr Richardson felt satisfied that the responsibility of having the engines properly inspected and overhauled periodically could be fixed if the inquiry were extended. He therefore referred the matter again to the Board, who took further evidence. In the report now furnished, the Board hold Loco. Inspector Thompson blameable, but point out as a mitigating circumstance that he had not received "written instructions" respecting inspections and overhauls. Weekly Times (Melbourne, Vic. : 1869 - 1954), Saturday 7 July 1894, page 32 The Ringwood Boiler Explosion. The Minister of Railways takes exception to the tone of a paragraph appearing in a morning contemporary respecting the Ringwood boiler explosion. It makes it appear that Mr Richardson has referred the report of the board which considered the facts connected with the explosion to the Crown solicitor simply because he differed from the finding of the board. The Minister explains that when he received the report he found that the responsibility for having boilers properly inspected and overhauled had not been clearly fixed. He personally obtained farther evidence on that point, and arrived at a conclusion, from which the commissioners differed. As he did not like to take upon himself the responsibility of deciding upon the effect of the evidence, he submitted the matter to the Crown Solicitor, but that officer did not furnish him with the information sought. He has, therefore, referred the question to the Attorney-General, together with the draft of a regulation respecting boiler inspections and overhauls in the future. Mr Richardson says that his whole aim is to have the responsibility positively fixed. Weekly Times (Melbourne, Vic. : 1869 - 1954), Saturday 28 April 1894, page 23 The Minister of Railways has completed his consideration of the supplementary report received by him from the Ringwood Boiler Explosion Board. The report, it will be remembered, held Loco-Inspector Thompson blameable for the non-inspection of the boiler, but considered there was extenuating circumstances. There was a certain amount of doubt as to the absolute instructions given for overhauling engines periodically. Mr. Richardson is sending the report on to the Commissioners with instructions that the responsibility respecting inspection of boilers shall be made clear for the future.

Item issued to 20164 Granville Inverell Hamilton BULLUSS Born 12/11/1909 in Hamilton NSW . He enlisted at Tamworth into the RAAF. Service records not available to the public.RAAF Fitters Manual II.E belonging to L.A.C G. Bulluss. Book has black binding with black cord to bind it. Cover is a dirty cream colour with black writing. On front cover in two drawings in ink.R.A.A.F. 3613 Fitters II.E Flight Mechanics, Course Notes, Engineering School. Issue 3 - 1941. This book is R.A.A.F Property and is NOT TO BE REPRODUCED without authority. Inside cover written in ink is numerous names and addresses. On the front cover is a drawing of clouds and rain and the RAAF crest. Inside on various pages is some sketches in pencil, quite a few of people in profile.raaf, manual, wwii, world war 2

A set of plans and drawings relating to the CSIRO research vessel. There are 10 clear plastic pockets each containing drawings. The collection has a hard plastic cover. There are two loose leaf pages at the front of the collection - a title page and a list of contents. non-fictionSet of plans relating to CSIRO Research Vessel 1980nautical, seamanship, maritime, vessel, plans

(1) Site Plan by Alexander Metherell Pty. Ltd. Job No BHC/1 Drawing No SP/3 dated Dec 1983. On reverse, Plan SP/3 Library - Boulevard." (2) 4 tracing paper copies with various annotations. (3) Tracing paper planting plan. (4) Coloured, laminated copy, Proposed Planting: Engineering Block and 2 sketches on tracing paper and paper. Also see B15.0352 for Full Report.alexander metherell, library

British Army Manual Army code 70427.This is a vinyl covered book. Dark blue colour, the printing is in gold ink. Inside are instructions for field engineers with drawings and charts. At the rear are several lined square blank pages, 1" square. They are a different shade. The binding is metal and pages can be removed.military engineering, manual, royal engineers

The drawing titled "Ballarat Rolling Stock Wiring Diagram - Existing and Proposed Tail Light Installation" shows wiring for both single-truckers and bogie trams. Shows switches, lights, and wiring layout. Does not include a battery that was actually installed. Drawing undated, possibly c1949.Yields information about possible wiring of tail lights in Ballarat trams.Foolscap drawing - faded, undatedsecv, ballarat, tail lights, electrical engineering

Yellow cover, bound booklet. On front cover WMC Engineering Services Pty Limited. Lump Sum Contract No BGO 05., specification for double drum winder conversion Carshalton shaft, Bendigo Gold Operations. December 1987 .Booklet contains conditions of tendering, conditions of contract, draft agreement, and specifications. Appendices: drawing list; pricing schedule; contract summary and schedule of fees. double drum winder, specifications, wmc engineering, bendigo gold, gold mining

Used by Colin Sach during his employment as Manager of the Chemistry Dept. at the University of Melbourne over a period of forty years.Manufacturing History Museum Victoria Commentary: Australian manufacturing history Philip Wollen Many years ago, when I was an ambition young man, I took over a company called Hecla.|This business was formed in 1872, long before Federation was even contemplated. The company established a rich tradition in the Australian manufacturing industry. The prodigious product range included kettles, mixers, toasters, hairdryers, urns, pie warmers, bain maries, and electric blankets for the domestic and commercial market. During the war it even manufactured parts for aircraft. It was one of Melbourne's largest employers.|Hecla was one of the pioneers in TV advertising, led by icons like Bert Newton, Bobby Limb, Evie Hayes and Graham Kennedy who ad Jibbed his way through irreverent and unscripted naughtiness about Hecla electric blankets and foot warmers. The slogan was 'By Hecla, its good1'. One can imagine the fun Bert and Graham had with their double entendres.|In the 60's Hecla entered into a partnership with General Electric and expanded rapidly. The massive factory, on the corner of Alexandra Parade and Chapel Street overlooking the Yarra River was a Melbourne landmark.|The business was formed by one of the scions of Melbourne industry. Mr Marriott was a metal worker of some repute, building the lights in front of Melbourne's Parliament House, the first steam car, the sideboard at the RACY Club, and the first factory to run on electricity.|By the time I acquired the company it was a shadow of its former self, incapable of competing with cheap Chinese imports. Wandering around the warehouse late one night I discovered a large, boarded up storeroom which appeared not to have been opened in decades.|Over several months I combed through the room, unearthing a treasure trove of products from a bygone era. Dusty files, engineering drawings, wooden prototypes, patent records, and correspondence from distributors on every continent.|I decided to track down an old man, Ray, long retired after 50 years with Hecla. He was not well off financially and welcomed the paid work. It turned out that he had done his apprenticeship with the company and there wasn't much he didn't know about it. He had been personally involved in the manufacture of almost every type of product on the Hecla smorgasbord's of products.|So for over 2 years he methodically assembled a mini museum of Hecla products, painstakingly polishing them and ensuring they were in working order. He attached the original brochure of each product and their respective warranty cards. For him it was ,a labour of love. For me it was a fascinating, if vicarious journey, into Australia's manufacturing past.|My colleagues complained that I was wasting money on his salary, our time and factory space on stuff that should have been dumped years ago. I tried to explain that I was merely a steward of the Hecla tradition, not merely an owner. Besides, the look on Ray's face convinced me that there was another dynamic at work. One I could see, but didn't really understand.|After he Passed away I faced a dilemma. What to do with this 'museum' of Hecla history. Nobody was interested.|So I kept the 'stuff' in private storage, hoping that same day someone would be interested in it. And the years passed.|Finally, I had a brainwave. Perhaps the Melbourne Museum would be interested. It was a long shot but I made the call. I had a nagging suspicion that they would think I was simply trying to get them to relieve me of paying for this huge collection to be taken to the tip.|To my surprise they said they would be willing to take a look, I secretly hoped that they would take the whole collection and not leave me with an incomplete jumble of appliances that I would indeed have to take to the tip.|On the appointed day, four serious looking young people showed up. Armed with digital cameras, note books and poker faces they spent four hours analysing the goods and the supporting materials. I asked them if they had any interest and their response was decidedly non-committal. It depends on the acquisitions committee, I was told. I was disheartened and packed up the exhibits to go back into storage.|Imagine my surprise when months later they telephoned to say that they had researched the history of the company, and yes, they would like to take the whole collection. And a truck with 'handlers' would arrive the following day to pick it up. Two years ago all Hecla's archives left me forever and went to the Museum's warehouse.|Well, to my delight I received a call yesterday inviting me to a private viewing of the exhibition at the Melbourne Museum. These young historians had meticulously assembled an impressive display of Melbourne's industry and technology going back to the 1800's. They thanked me like a significant benefactor when it is I who should have thanked them.|I saw the excitement in the eyes of these young people who had somehow managed to dig out and assemble memories from Australia's past. If this is the standard of care that the curators of the Melbourne Museum show all their exhibits, our history is in safe hands.|Their meticulous work took me back to those years long ago when I saw an old man lovingly assembling and cataloging a lifetime of his work.|It took me back to the day when Australians actually made things. Long before we became a nation of quarrymen. Before we became animal-factory 'farmers'. Of a time when products didn't break down, or dumped and replaced before the warranty expired. When men like Mr Marriott cared deeply about what their hands produced.|It reminded me of the call I received from an elderly lady in Tasmania asking for the electrical element for a Hecla K7 kettle. I searched the archives and called her back. The K7 was produced decades earlier and we no longer carried that spare part. She was quite disheartened and told me her kettle had finally 'given up the ghost' and she couldn't bear to part with it. It was a present from her husband on their wedding day 45 years ago. Her final words were 'they don't make them like that, do they? By Hecla they were good1'|I'm glad I followed my instinct and put Ray back on the payroll all those years ago..|I like to think Mr Marriott would have been pleased.Square metal box with electrical elements inside. Used to stand on or to put feet on when sitting. Elaborate pattern in centre with inscription.Hecla Foot Warmerdomestic items, heating