Eight page foolscap typed (carbon copy) instruction sheet titled "Rules and Instructions for Traffic Inspectors", pinned in the top left hand corner. Dated 12/9/1950. Published by the MMTB. Details the duties of the Inspectorial staff, details 41 rules covering general matters, staff supervision, traffic, accidents, and investigation of accidents. Has "AWM/ERR.2/9/50." typed in top left hand corner of first sheet.In black ink across top of instruction "BTPS 318." Has about six sets of initials along top edge.trams, tramways, mmtb, instructions, traffic staff, inspectors, accidents

One page foolscap typed (carbon copy) instruction sheet titled "Notice to Inspectors.", Dated 24/6/1952. Published by the SEC Ballarat Tramways, Traffic Office and signed by Les Denmead as Branch Tramways Superintendent. Notes the importance of Inspectors as supervisors and observers, recent complaints, working hours, theatre finishing times, accidents, reports and keeping the trams moving.In black ink across top of instruction "BTPS 319." trams, tramways, sec, instructions, traffic staff, inspectors, accidents

Three page foolscap typed (carbon copy) instruction sheet titled "Questions - Applicants for Inspectorship", Dated 18/2/1946 pined in top left hand corner. Pages 2 and 3 stapled together. First page asks 10 questions of a varied nature and pages 2 and 3 gives suggested answers. Has initials THT/HEJ in top left hand corner. Asks questions re a person damaging a tram, trolley wire falling onto the road, derailments, obstructions, improper tickets, how to use a loop if part defective, how to maintain service, intoxicated or drunken crew, complaints from passengers.In black ink across top of instruction "BTPS 320." trams, tramways, sec, instructions, traffic staff, inspectors, accidents

One page quarto size typed (carbon copy) instruction sheet titled "Inspectorship Questions for Applicants", Dated 5/10/1949. Asks 5 questions of a varied nature. Has initials THT/MRC in top left hand corner. Asks questions re complaints from passengers, gambling on SEC premises (rule 25), motormen leaving trams in the street, rule 24 (intoxication) and exchanging of duties between conductors and motormen.In black ink across top of instruction "BTPS 321." Has in pencil on bottom of sheet, Perdue, Maxwell and J. Young. trams, tramways, sec, instructions, traffic staff, inspectors, accidents

Two page foolscap size typed (carbon copy) instruction sheet titled "Notes: / Applicants for Inspectorship", Dated 20/9/1957 and pinned together in the top left hand corner. Asks 10 questions of a varied nature Has the answers within the paragraph. Has initials AVM/ERA in top left hand corner. Asks questions re duties, instructions, towing or pushing trams, track obstructions, ticket irregularities, intoxicants, derailments, rerailing of bogie trams, serious accidents and honesty of conductors.In black ink in top right hand area of instruction "BTPS 322." trams, tramways, sec, instructions, traffic staff, inspectors, accidents

Three page quarto size typed (carbon copy) instruction sheet titled "Questions / Applicants for Inspectorship", Dated 31/5/1963 and pinned together in the top left hand corner. Asks 10 questions of a varied nature Has initials LJD/PB in top left hand corner. Pages 2 and 3 detail the suggested answers. Asks questions re people found damaging SEC property, trolley wire on road, derailments, track obstructions, ticket irregularities, pedestrian accidents, traffic, drunken crews, passenger complaints and duties.In black ink in top right hand area of instruction "BTPS 323." trams, tramways, sec, instructions, traffic staff, inspectors, accidents

One page foolscap size typed (carbon copy) instruction sheet titled with Questions and Answers for Acting Inspectors. Dated 28/6/1966. Asks 9 questions of a varied nature Asks questions re duties, derailments, track obstructions, ticket irregularities, pedestrian accidents, traffic, drunken crews, passenger complaints conductor honesty.In black ink in top right hand area of instruction, "Acting Inspector 1966 / 28th June", "BTPS 324." Changes to question 1 - additional sub-question and answers. trams, tramways, sec, instructions, traffic staff, inspectors, accidents

One page foolscap size typed (carbon copy) instruction sheet titled "Applicants for Senior Inspector", Dated 1966. Asks 8 questions of a varied nature, typed in a Question and Answer style. Has initials LJD/JMc in top right hand corner. Asks questions re ATMOEA award, Rule 10 or crews affected by alcohol, duties, traffic rosters, rerailing a tram, track obstructions, passenger complaints, ticket checking.In black ink in top right hand area of instruction "BTPS 324.", "1966" and in question 6, the word "moved" written in for the word "used". trams, tramways, sec, instructions, traffic staff, inspectors, accidents

Demonstrates aspects of Safeworking on the Ballarat Tramway system from 1960 to c1936 when replaced by electric signs. Yields Information about the operation of Ballarat's trams and safeworking procedures.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "VICTORIA PARK LOOP / CARLTON ST LOOP" stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg. The top line of words has a reddish paint inlay. Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, to 53, 2473 and 4444 to 4448 and Reg item 934 and 988 for articles on the safeworking systems.trams, tramways, staff, safeworking, tramway staffs, sec, signals

Demonstrates aspects of Safeworking on the Ballarat Tramway system from 1960 to c1936 when replaced by electric signs. Yields Information about the operation of Ballarat's trams and safeworking procedures.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "CAR SHED LOOP / MACARTHUR ST LOOP" stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg. The stamped area appears to have been polished compared to the others. Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, to 53, 2473 and 4444 to 4448, 4496 and Reg item 934 and 988 for articles on the safeworking systems.trams, tramways, staff, safeworking, tramway staffs, sec, signals

Yields information about the drawings that were used by the depot or workshop staff as reference drawings. Has a strong association with the depot workshop staff. Yields information about equipment on Ballarat tramcars and Signalling.Folder containing 46 blueprints or Dyeline prints of SEC tram equipment drawings. Front of folder made from a cloth back sheet of paper extended to secure to a thick cardboard runner. Rear of folder made from an old tram advertising panel or cardboard sheet, cut to size and secured to a thick cardboard runner with a cloth backing on both sides. Sheets secured with three brass screwed clips. Front cover damaged in bottom right hand corner. Rear cover breaking apart on outside around cloth binding. Heavy dirt marks from “grease” on bottom half of rear cover. Contains 46 drawings which have been individually catalogued and numbered on the rear of each drawing within the folder. Some of the drawings have been folded. Reg Item Micro Film No. Old BTPS No. SEC Drawing No Title 4807 42/4 1 VB4/8103C Westinghouse T1F Controller Main Cylinder Segments. 4867 47/2 2 BA-T8-8128 Westinghouse 225N Motor Case Bolt 4830 22/3 B 3 BA-T7-7666 Half Ball Brake Hanger Link, Driving Wheel, Brill Maximum Traction Truck 22E 4868 44/3A 4 BA-T8-8113 Split Suspension Bearing for Type W225 Motor (Westinghouse) 4869 52/2 5 BA-T8-8158 Contact Tips for G.E. Compressor Controller 4818 52/3 6 BA-T8-8159 GE B-23 Contact Finger Tips for G.E. Type ‘B’ Main Cylinder 4870 6/1 7A BA-T3-6734 Brass Nut for Switch Mechanism 4829 6/2 7B BA-T3-6735 Tongue Clip Link for Switch Mechanism 4871 6/3 7C BA-T3-6736 Fulcrum for Switch Mechanism 4872 6/4 7D BA-T3-6737 Plunger for Switch Mechanism 4832 7/6 8 BA-T3-6754 Pivot for Switch Mechanism No numbers 9 or 10 4873 17/5 11 BA-T7-7639 Detail of Motor Pinion for Brill Cars 4831.2 21/4 B 12 BA-T7-7661A Half Ball Hanger Links – single bogie trucks 4874 21/6 13A BA-T7-7663 Axle Box Inner Spring Driving Wheels Maximum Traction Truck 22E 4875 22/1 13B BA-T7-7664 Axle Box Outer Spring Driving Wheels Maximum Traction Truck 22E 4876 22/2 14 BA-T7-7665 Body Spring Brill Maximum Traction Truck 22E 4830.2 22/3B 15 BA-T7-7666A Half Ball Brake Hanger Link Driving Wheel Brill Maximum Traction Truck 22E 4877 22/4 16 BA-T7-7667 Body Spring, Brush Maximum Traction Truck 22E 4820.2 22/6 A 17 BA-T7-7669 Wear cups for Half Ball Brake Hanger Links, Single & Double Bogie Trucks 4878 50/5 18 BA-T8-8149 Connections of Line Breaker and Ratchet Switch for use with Drum Controller 4879 74/6 19 BA-T13-8757/9 Signal boxes, Back of Panel Wiring and External Connections 4880 45/1 20 BA-T8-8116 Trolley Harp 4806 15/3 21 BA-T7-7625 Equalizing Lever, Fulcrum, Brill 21 E truck 4881 15/5 22 BA-T7-7626A Brake Beam Fulcrum Brill 21E truck 4808 16/1 23 BA-T7-7628 Pinion Remover, GE 201G and GE 202 motors 4882 16/3 24 BA-T7-7630 Spring Posts, Brill 21E Truck 4883 21/3 25 BA-T7-7660 Brake Shoe Holder, Driving Wheel, Maximum Traction Truck Brill 22E 4884 21/5 26 BA-T7-7662 Brake Rod Guide, Single Bogie Trucks 4885 22/5 27 BA-T7-7668 Brake Shoe Holder, Pony Wheel, Maximum Traction Truck Brill 22E 4809 42/2 B 28 BA-T8-8101 Trolley Wheel and Axle 4815 42/1 B 29 BA-T8-8102A Motor Suspension Bearing, GE 202 Motor 4796.2 42/5 30 BA-T8-8104 Connection Diagram WH 225N Motor 4886 42/6 B 31 BA-T8-8105B Motor Suspension Bearing, GE 201 Motor 4797.2 48/6 32 BA-T8-8137 WH T1F Controllers 4816 49/2 33 BA-T8-8138 Connection Diagram GE 202 Motor 4887 49/3 34 BA-T8-8139 Connection Diagram K-36-J Controller 4888 50/3 35 BA-T8-8146 GE K-36-JR Controllers, with line breaker (Connection diagram) 4889 50/6 36 BA-T8-8150 Commutator for Westinghouse 225N Motor 4846 51/1 37 BA-T8-8151A Armature Bearing Lining, Commutator End, Type GE 201G Motor 4813 51/2 38 BA-T8-8152 Armature Winding Diagram Westinghouse 225 Motor 4840.2 51/40 39 BA-T8-8154A Armature Bearing Lining, Pinion End, Type GE201G Motor 4890 51/6 40 BA-T8-8156 Armature Bearing Lining, Pinion End, Type GE202A Motor 4891 52/1 41 BA-T8-8157A Armature Bearing Lining, Commutator End, Type GE202A Motor 4892 64/5 42A BA-T9-8392A Step Hangers, Single and Double Bogie Trucks, Hinged Type 4785.2 64/6B 42B BA-T9-8392/1A Step Hangers, Single and Maximum Traction Trucks, Fixed Type 4812.2 43/1 43 BA-T8-8106B GE K36J Controller, Main Cylinder Segments 4893 50/2 44 BA-T8-8145A GE B23E Controller, Main Cylinder Segments 4816 65/2 45 BA-T9-8394B Door Lock for Motorman’ Cabin Maximum Traction Trucks. 4810 73/3 46 BA-T13-8757 Ballarat Electric Tramways Signalling System, Arrangements & Details of Box.On front cover of folder, "1 - 46"trams, tramways, drawings, ballarat, sec, depot, workshops

Yields information about the distribution of the SEC tramway by-laws to workers and need to bring to attention to tramway staff, the rules regarding entering hotels and being intoxicated.Set of three letters or copies that involved the publication of the SEC's "Tramways by-Law No. 1" and Rules Governing Employees in 1940. .1 - From Manager Commercial Division, to Manager Ballarat - regarding amendments to the By-Laws (Sheet 17) and future documents - quarto paper, typed, 19/7/1940. .2 - Engineer and Manager (Head Office) regarding reminding employees of Rule No. 23, Rules Governing Employees - about entering hotels and intoxicating liquors, following up a recent case and asking him to send a memo out. Quarto paper, typed, 15/11/1940. .3 - Copy of Memo re above, dated 19/11/1940. to the Tramway Inspectors, quarto, carbon copy - green paper.trams, tramways, by laws, sec, hotels, rules, alcohol

Yields information about the distribution of the SEC tramway by-laws to workers and staff in 1956.Carbon copy of memo on green demi foolscap paper dated 16/8/1956 to the Branch Tramway Superintendent from the Manager Ballarat, regarding forwarding five copies of "Tramways By-Law No. 1", brought from Melbourne.trams, tramways, by laws, sec

Yields information about the correspondence between the SEC staff about the opening of tram tracks for underground services.Original of a report, handwritten in pencil from a copy book (pages 26 and 27), dated 23/3/1937, addressed to the Manager, from Mr. Mawby titled "Opening up of tram tracks by Plumber etc" reporting on a Mr. McLean excavating under track in Drummond St on 23/3 for a Ballarat Water Board pipe and the issues that arose. No notification to the SEC, underground services, and the absence of advice from traffic crews. Gas company also mentioned in the letter.Various initials and notes in red pencil or ink.tram, trams, letters, sec, tram track

Has a strong association with BTM staff c2007, in the meal room of the BTM depot.Laminated A4 colour print of six BTM members in the meal room, Begonia festival? c2007. Photographer unknown at time of cataloguing, In photograph are: Carolyn Cleak, Greg Rogers, Andrew Paroissien, Guye, Graeme Cleak and Merle Clowes.trams, tramways, btm, depot

Has a strong association with BTM staff, Richard Gilbert c2007.Laminated A4 colour print of Richard Gilbert, c2007. lifting the pole on No. 40 at St Aidans Drive. Photographer unknown at time of cataloguing, trams, tramways, btm, st aidans drive, trolley poles, tram 40

Has a strong association with BTM staff, Richard Gilbert c2007.Colour print of Richard Gilbert holding the trolley rope on No. 27 prior to turning the pole at Carlton St terminus. Photo c2006, prior to repainting of the tram. Photographer and date unknown at time of cataloguing, trams, tramways, btm, carlton st, trolley poles, tram 27

Has a strong association with BTM staff, Richard Gilbert, Alan Snowball, and Carolyn Dean c2006.Laminated A4 colour print of publicity filming at the depot c2006, featuring Richard Gilbert, Alan Snowball and Carolyn Dean, with tram 671 in the background.trams, tramways, btm, depot, publicity, tram 671

Has a strong association with BTM staff, Richard Gilbert c2008.Laminated A4 colour print of Richard Gilbert talking to a visiting group of Seniors, c2008 in tram 661.trams, tramways, btm, visitors, special trams, tram 661

Has a strong association with BTM staff, Neil Lardner c2005.Laminated A4 colour print of BTM Conductor Neil Lardner giving a ticket to a passenger on a single truck tramcar, c2006, Begonia Festival, Carolyn Dean. Used in the 2005 - 2006 Annual Report.trams, tramways, btm, conductors, tickets

Yields information about the appearance of Bendigo electric trams at the time of opening, how passengers could be seated, staff, paint schemes, decorations, and truck arrangements.Black and White photograph of four trams at Charing Cross, taken from the south east corner, looking towards the Beehive building and Ezywalkin stores. Trams 7, 5 and 26 in the photograph. Photo by Andrew Ward 15.1.1972.On rear in ink "Sat 15.1.72" / "single truck car 7 and bogie cars 5 & 26" in the top left hand corner and in a mix of ink and pencil "Bendigo Trust / Andrew C. Ward, Bendigo Vic 3550".trams, tramways, bendigo, charing cross, pall mall, tram 7, tram 5, tram 26

Yields information about the operation of the BTM and the management of tramcar operations. Demonstrates how information within tram crews and shed staff was distributed.Fifty Six page document within grey card covers, folded A4 paper to form an A5 booklet titled "Ballarat Tramway Museum Operations Manual, December 2008". Provides details of the manual, index, operational procedures, driver training, requirements, many procedures, and some forms. Issued to existing workers and new workers at the time. See memo in back of worksheet for Reg item 4440 for details and mailing list.trams, tramways, btm, operations, instructions, procedures

Yields information about the operation of the BTM and the management of tramcar operations. Demonstrates how information within tram crews and shed staff was distributed.Twenty four page document within yellow card covers, folded A4 paper to form an A5 booklet titled "Ballarat Tramway Museum Conductor Operations Manual, November 2008". Provides details of the manual, index, operational procedures, map, requirements, many procedures, and some forms. Issued to existing workers and new workers at the time. See memo in back of worksheet for Reg item 4440 for details and mailing list.trams, tramways, btm, operations, instructions, procedures, conductors

Yields information about the operation of the BTM and the management of tramcar operations. Demonstrates how information within tram crews and shed staff was distributed.Thirty Six page document within grey card covers, folded A4 paper to form an A5 booklet titled "Ballarat Tramway Museum Driver Operations Manual, November 2008". Provides details of the manual, index, details of tramcar equipment, tramcar braking, fault finding and Operating Instructions. Issued to existing workers and new workers at the time. See memo in back of worksheet for Reg item 4440 for details and mailing list.trams, tramways, btm, operations, instructions, procedures, drivers

Demonstrates aspects of Safeworking on the Ballarat Tramway system from 1960 to c1936 when replaced by electric signs. Yields Information about the operation of Ballarat's trams and safeworking procedures.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "CARLTON ST HADDON ST LOOP " stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg. Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, to 53, 2473 and 4444 to 4448, 4996 and 4497 and Reg item 934 and 988 for articles on the safeworking systems.trams, tramways, staff, safeworking, tramway staffs, sec, signals

Demonstrates aspects of Safeworking on the Ballarat Tramway system from 1960 to c1936 when replaced by electric signs. Yields Information about the operation of Ballarat's trams and safeworking procedures.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "DARLING ST LOOP RUBICON ST LOOP " stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg. Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, to 53, 2473 and 4444 to 4448, , 4996 and 4497 and Reg item 934 and 988 for articles on the safeworking systems.Ballarat Tramways Section Staff Darling St Loop Rubicon St Looptrams, tramways, staff, safeworking, tramway staffs, sec, signals

Demonstrates aspects of Safeworking on the Ballarat Tramway system from 1960 to c1936 when replaced by electric signs. Yields Information about the operation of Ballarat's trams and safeworking procedures.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "URQUHART ST LOOP TO GREY ST LOOP " stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg. Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, to 53, 2473 and 4444 to 4448, , 4996 and 4497 and Reg item 934 and 988 for articles on the safeworking systems.trams, tramways, staff, safeworking, tramway staffs, sec, signals

Demonstrates aspects of Safeworking on the Ballarat Tramway system from 1960 to c1936 when replaced by electric signs. Yields Information about the operation of Ballarat's trams and safeworking procedures.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "PLEASANT ST TO CARLTON ST LOOP " stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg. Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, to 53, 2473 and 4444 to 4448, , 4996 and 4497 and Reg item 934 and 988 for articles on the safeworking systems.trams, tramways, staff, safeworking, tramway staffs, sec, signals

Demonstrates aspects of Safeworking on the Ballarat Tramway system from 1960 to c1936 when replaced by electric signs. Yields Information about the operation of Ballarat's trams and safeworking procedures. Demonstrates what can happen in use - has been run over by a tram - possibly being exchanged on the move or some other story.Cast brass item with a flat part recessed section with the words "BALLARAT TRAMWAYS SECTION STAFF" cast into the surface and a flat section underneath, flush with the outside edges in which the words "STURT ST RUBICON ST " stamped in. Has an open rounded end which forms a handle or a point where it could be hung on a peg. The staff has been run over by a tram and had the last part of the object cut off. Used as a means of authorising a tramcar to have sole use of the track between the named points to avoid head on collisions. Safeworking object - known as a section staff. Not known when made, but in use until the introduction of the electric signalling in the mid 1930's by the SEC. See also Reg Items 934 and 988 for details of use and other examples are at 1851, to 53, 2473 and 4444 to 4448, , 4996 and 4497 and Reg item 934 and 988 for articles on the safeworking systems.Ballarat Tramways Section Staff Sturt St Rubicon Sttrams, tramways, staff, safeworking, tramway staffs, sec, signals

Yields information about the roster for the Ballarat tram depot staff - pitmen, cleaners etc.Plastic covered sheet of paper which has been typed to provide a five week rotation roster for the Tram depot staff, dated 30/5/1968. Gives Afternoon and night shifts. Titled "Tramway Depot (Five Day Forty Hour Week) Roster". The sheet of paper has been covered both side with an adhesive plastic film.trams, tramways, ballarat, depot