Black powder splitting guns were commonly used to split large logs into more manageable pieces before the advent of excavators and front-end loaders in bush logging operations. A typical splitting gun used in Victorian forests was a piece of high-grade steel about 1-1/2 to 2 inches in diameter and about 16 inches long, and slightly tapered at one end. They had a ¾ inch hole drilled about 9 inches deep into the centre of the shaft with a small pilot hole drilled from the outside to load the fuse. The tube was carefully loaded with an amount of black gunpowder using a funnel and spoon. Experience being the guide on how much powder to use, which depended on log size, species and difficulty of splitting the wood. The hole was stopped with a piece of wadded paper and the gun positioned at the end of a length of the log to be split. The splitting gun was then belted into the log with a large wooden maul or even the back of an axe to a depth of about 3 to 4 inches. There were often markings as a guide. This also had the effect of tamping the black powder inside the gun. Preferably the gun was backed up by another large log to absorb the recoil shock and avoid it flying off in the bush somewhere. I have seen guns where a length of string and coloured flag could be attached to help find them. A length of fuse was then inserted in the small hole and lit. Kaboom !!!! Needless to say, the splitting gun was a dangerous implement.Log Splitting gun (large 50cm)forests commission victoria (fcv), hand tools

Black powder splitting guns were commonly used to split large logs into more manageable pieces before the advent of excavators and front-end loaders in bush logging operations. A typical splitting gun used in Victorian forests was a piece of high-grade steel about 1-1/2 to 2 inches in diameter and about 16 inches long, and slightly tapered at one end. They had a ¾ inch hole drilled about 9 inches deep into the centre of the shaft with a small pilot hole drilled from the outside to load the fuse. The tube was carefully loaded with an amount of black gunpowder using a funnel and spoon. Experience being the guide on how much powder to use, which depended on log size, species and difficulty of splitting the wood. The hole was stopped with a piece of wadded paper and the gun positioned at the end of a length of the log to be split. The splitting gun was then belted into the log with a large wooden maul or even the back of an axe to a depth of about 3 to 4 inches. There were often markings as a guide. This also had the effect of tamping the black powder inside the gun. Preferably the gun was backed up by another large log to absorb the recoil shock and avoid it flying off in the bush somewhere. I have seen guns where a length of string and coloured flag could be attached to help find them. A length of fuse was then inserted in the small hole and lit. Kaboom !!!! Needless to say, the splitting gun was a dangerous implement.Log Splitting gun (large 45cm)forests commission victoria (fcv), hand tools

This item would have been used to apply rouge to the face to make the cheeks red. This rouge holder was made to fit into a purse or pocket for quick and easy application of the rouge. Variants of rouge or reddening materials are still used in cosmetics today. This item is of minor interest as an example of a cosmetics holder in use in the 20th century. It will be useful for display. This is a small brass container. It is rectangular in shape and has curved sides with ridged lines along the top and bottom edges. It opens via a small clip to reveal two compartments hinged in the middle. One compartment has an oval recess containing rouge powder and the other compartment has an inset mirror which is broken in two. A cloth pad for daubing the rouge on to the cheeks is also inside the container. ‘Velvet Grape’ cosmetics, history of warrnambool

Three black and white photos mounted on buff cardboard. Photos depict remains of wall of the Arblaster's Powder Factory with three men inspecting site, thickness of wall 3 ft., and Arblaster's home in Arblaster St., Eaglehawk. House is miner's cottage, with lace iron work on verandah, white post and rail fence outside. Photos taken by unknown person, however, could be Albert Richardson ?business, mining, arblaster's powder factory, arblaster's powder factory, arblaster, explosives, eaglehawk, bendigo, mining

Beam balance in timber glass case brass and metal beam balance in fair condition crystal pivots, with three leg levelling legs and small string plumb bob to establish initial balancing of the scales balance arms have removable glass concave infills, to measure powders Possible handmade glass case with double glass doors right hand side glass panel cracked

Cartridge fuse - Tramcar Component - black Bakelite? with brass ends, possibly containing a powder given the weight and a fuse wire. Has remnants of a paper label around the centre. No details of the of the manufacturer or date. Type used for a compressor fuse. At one end has a diamond with a vertical bar through the centre and 10 stamped into the brass end - possibly a 10Amp fuse and possibly the manufacturer's symbol.fuse, tramcars, electrical engineering, electrical equipment

35mm Kodak white cardboard colour slide by Keith Kings of W5 760 at Haymarket Junction, Royal Parade, with the destination of Coburg, Route 20 with an auxiliary board for Carlton Football Ground.. Has adverts for Neals, Victor Board and Courage beer and Vincents headache powders. In the background are adverts for Qantas and the CBA Bank. Taken 7/6/1969 See inscriptions re the tram.Keith Kings stamp and number "56-23", with details of exposure. W5 760 with half drop windshield, Sydney Rd cnr Flemington Road 7/6/69"trams, tramways, w5 class, haymarket, coburg, route 20, royal parade, tram 760

The Nestle factory at Dennington was commenced in 1907 and proved to be a big boost to the local economy. The first product manufactured was sweetened condensed milk which began in 1911 and by 1944 was the largest plant in the Southern Hemisphere. They went on to produce Lactogen, full cream milk powder and in 1966 Milo and Nescafe. On average up to 650 people were employed. Nestle relinquished their link with the site when it was sold to Fonterra in 2005. A link to one of the longest established businesses in Warrnambool. Many people supplied milk and it employed many local people and as such has strong links to the district. White china cup with black transfer of Dennington factory and dates in black.Dennington factory 100 years 1911-2011nestle dennington, history of warrnambool, nestle milk products dennington

The Nestle factory at Dennington was commenced in 1907 and proved to be a big boost to the local economy. The first product manufactured was sweetened condensed milk which began in 1911 and by 1944 was the largest plant in the Southern Hemisphere. They went on to produce Lactogen, full cream milk powder and in 1966 Milo and Nescafe. On average up to 650 people were employed. Nestle relinquished their link with the site when it was sold to Fonterra in 2005. A relic from a significant part of Warrnambool’s history, industry and agriculture and a large number of long serving employees.Terracotta coloured six sided, one side flat and the reverse with raised bars. Material is either clay or concrete. Handwritten in pen, “from the floor of the Nestle Factory Dennington. warrnambool, dennington, nestle, condensed milk, nescafe, milo, lactogen.

Mac's Shortbread Co dates its history back to a family bakery in Abbotsford opened in the 1860's producing bread for the goldfields. This eventually became McAlpine's Flour. This business was sold in 1960 and the family then purchased a cake shop, leading to building a biscuit factory. (This is thought to have been the Surrey Hills site). The company outgrew this and moved to 5 Tate Drive, Kerang. (Further research required.) Australia adopted metric units of measurement in July 1974, so this object was manufactured after 1974.This tin is material evidence of the small area of industrial activities that once existed in Surrey Hills.A cylindrical tin with a silvered interior and the outside finished in a white enamel paint, on which there is a geometric design incorporating a butterfly.On a label incorporated in the design: "Mac's / MAC'S SHORTBREAD CO. 1 NORFOLK RD./ SURREY HILLS, VIC. AUST. 3127 - 8360333 / BUTTER / SHORTBREAD / INGREDIENTS: WHEAT FLOUR, CHOICE BUTTER, / SUGAR, EVAPORATED MILK, BAKING POWDER / 300 g NET"bakeries, surrey hills, mac's shortbread, norfolk road

Framed colour poster titled: "new energies/Contemporary Artists of South Gippsland" 18-19 March 2000, Memorial Hall, Leongatha. Black card window mount set in green powder coated metal frame. features a photomontage of art and craft images with text headings which include: "ceramics, photography, sculpture, print, paint, furniture, advice, workshops, technology, galleries, exhibitions, and networking".

The letter to Mr A Ferris was from Mr and Mrs R Ferris of Bristol U.K thanking him for the food parcel. They were not related to each other. Australians sent food parcels to the UK after WW2. This one contained meat, milk, honey, cheese and jelly powder. It was organised through the “Bristol Society of Melbourne”. The letter is in the collections relating to Alfred G Ferris 2156 AIF, refer cat No 4183.3P for his service details.Envelope, “Air Letter”, light blue colour, all type in black, hand written on the front, dated 1947.Hand written, “Mr A Ferris Pte bag, Pyramid Hill Victoria Australia”air letters, food parcels, post ww2

Mac's Shortbread Co dates its history back to a family bakery in Abbotsford opened in the 1860's producing bread for the goldfields. This eventually became McAlpine's Flour. This business was sold in 1960 and the family then purchased a cake shop, leading to building a biscuit factory. (This is thought to have been the Surrey Hills site). The company outgrew this and moved to Kerang. (Further research required.)This tin is material evidence of the small area of industrial activities that once existed in Surrey Hills.A round tin with a silvered interior and the outside finished in a white enamel paint with the head and shoulders of a blond girl in red jumper, tartan sash and brooch and a tartan tam o'shanter hat.1. Mac's / Petticoat Tail BUTTER SHORTBREAD 450g NET./ BAKED IN AUSTRALIA BY MAC"S SHORTBREAD CO., 1 NORFOLK ROAD, SURREY HILLS, VICTORA AUSTRALIA PHONE 8360333 INGREDIENTS WHEAT FLOUR, CHOICE BUTTER, SUGAR, EVAPORATED MILK BAKING POWDERbakeries, surrey hills, mac's shortbread, norfolk road

This is a souvenir of the British Empire Exhibition of 1925. This exhibition, designed to showcase the industrial and natural resources of the countries in the British Empire was on a 216 acre site at Wembley, England. In 1923 the Wembley Stadium was completed and the F.A. Cup Final was held there. In 1924 the Exhibition was opened by King George V in a first ever radio broadcast by a British monarch. There were Palaces of Industry, Engineering, Horticulture and Art and Pavilions housing exhibits from most countries in the British Empire. 17 million people visited in 1923 and there were 11 million visitors in 1925 when the exhibiton was re-developed. Wembley Stadium was reconstructed in 2002. This item has no local provenance but is of some interest because of its connection to the British Empire Exhibition of 1925. It is a good example of the type of souvenir that was bought by visitors to the Exhibition. This is an enamelled metal container, circular (octagonal on the outside edges) in shape with a short handle. The central area is slightly recessed to take a small amount of rouge (a red powder compound for the face, usually the cheeks). A pad to apply the rouge to the face is missing. There is a metal hinged lid with a clip and a small ring at the end of the handle, possibly to contain a chain for it to hang around the neck. The wording on the front is black on a blue and green enamelled backgroundRaised image of a lion with the words underneath ‘British Empire Exhibition, 1925’rouge holder, british empire exhibition 1925

Agfa colour slide, blue / white plastic mount, photo by Keith Caldwell of SW6 919 nearing the corner of Swanston St and Victoria St, showing Glen Iris, route 6. Tram is northbound. The tram has adverts for Vincents headache powders, Rent A Holden and Tucker box. Alongside is a bucket with a red flag and equipment used by the point cleaners. In the background is the Ansett ANA building, 25/4/1964In ink "SW car 25.4.64"trams, tramways, swanston st, route 6, glen iris, victoria st, track cleaner, sw6 class, tram 919

Pulpwood was often split by hand or with black powder splitting guns into more manageable sizes and cut into 8 foot lengths (or billets). Billets were first stacked endwise to drain the sap and lighten the load before they were loaded by hand onto flat bed trucks for transport to the mills. This long length metal hook was used to pull and manoeuvre the pulpwood billets onto the truck. The advent of excavators in logging operations in the 1970s led to the loading and carting pulpwood in long tree lengths.Long steel tool with handle on one end and hook on the other.

Document, Advertising page for J.H.Abbott & Co.,Wholesale and Retail Warehouse, Market Square, Bendigo. Large Stocks,specially low Rates for Iron,Steel, Lead Paints, Oils, Tools,Black and Gal. Pipes, Candles, Powder, and Explosives, Wire ropes and Mining Supplies.Leather Goods a lot of which are Handmade.Special for Farmers: Superphosphates, Bone Dust, and all Manures, Binder Twine and Corn Sacks, Fencing Wire, and Rabbit-Proof Wire Netting.document, names of bendigo pioneers, j.h.abbott

Charles George De Beauvoir Tupper was the son of Daniel William and Elizabeth Tupper. He entered naval college in 1885 after securing a Royal Navy cadetship. Lieutenant Tupper transferred from HMS Swallow to HMS Racer in May 1893. Both ships were operating from the Cape of Good Hope station at the time. In September 1893 HMS Racer found itself in the middle of Brazil’s third military coup in four years. The squadron of British ships in Guanabara Bay comprised HMS Beagle, Racer and Sirius. Just before 2 pm on the afternoon of 3 November 1893 a party from each of the ships in the British squadron sailed up the harbour to obtain sand and enjoy a little land based recreation. Apparently, this was a weekly event and the sand was used to swab the ships’ decks. They landed on Governador Island, the largest of the hundred and thirty or so islands in the bay. The island was under the control of the navy insurgents and had two magazines or stores for powder and shells. The cutters from the HMS Racer and Beagle landed on the beach between the two stores. Charles was killed when the powder magazine exploded at 3.40 pm. Charles' father Daniel William Tupper was brevetted Colonel in 1866 and when Brigadier General George Jackson Carey was appointed to command the Australian forces and came to Melbourne, Daniel accompanied him. When Sir Charles Darling, the Governor of Victoria was recalled to England, Carey became Acting Governor of Victoria from May to August 1866. Daniel Tupper served as his Aide-de-Camp or private secretary during this time. Carey returned to England in 1867 to command the 2nd Infantry Brigade at Aldershot with Daniel Tupper as his Aide-de-Camp.Portrait with stained wooden frame. No glass covering the picture. Hooks and wire for hanging on the back. A printed sheet of paper with the hymn 'A voice from heaven' in loving memory of Charles George De Beauvoir Tupper - Died Nov 3 1893 - Aged 21 years has been glued to the back of the frame.With Mrs Tupper's kind regardslieutenant charles george de beauvoir tupper, elizabeth christie, lieutenant colonel daniel william tupper, hms racer, hms raleigh

Philip Webley was born in 1813, he was the younger brother of James Webley who was born in 1807. Both were born in Birmingham. Towards the end of the 1800s, the firm claimed establishment in 1790, this must have been the date James and Philip's father or grandfather originally established a bullet or gun implement making business. It was not, as is often stated, the date William Davis established his business. Philip Webley was apprenticed in 1827 to Benjamin Watson. James Webley also seems to have been apprenticed but to who is not known. In 1834 James and Philip established their partnership as percussioners, lock filers and gun makers at 7 Weaman Street,Birmingham which was William Davis' old premises Davis, a gun implement maker, mould and toolmaker, died in 1831 and his wife Sarah inherited the business at 84 Weaman Street which she ran with her daughter, Caroline. On 5 January 1838 Philip Webley married Caroline. Philip was recorded at 84 Weaman Street from 1838 as a gun percussioner, lock filer and gun maker and this is when the partnership was last recorded, but the brothers apparently continued to co-operate until 1845 when Philip reportedly sold his interest to James and used the money to purchase Sarah Davis' business. Even then, they worked together particularly about the design and manufacture of percussion revolvers. Philip Webley was recorded in the 1851 census as a 38-year-old gun and pistol implement manufacturer living at 84 Weaman Street with his wife Caroline they had four sons and one daughter Thomas William, Emma, and Philip Jnr, and two other sons, James, and Henry and Philip's cousin, also lived with the family probably as a nurse, Sarah Haywood. On 4 February 1853 Philip Webley registered patent No. 335 for a hinged revolver and on 14 September 1853 he registered patent No. 2127 for improvement for the first muzzle-loading percussion cap and ball revolver which became known as the "Longspur". In 1859 Philips son Thomas William, aged 21, was made a partner in the firm, which then changed its name to P Webley & Son and described itself as "Gun and Pistol Makers and Patent Revolving Pistol Makers", probably exploiting Philip Webley's patent No. 305 of February 1853 for a revolver frame and lock, and its improvement under patent No. 2127 of September 1853. Thomas later went on to managed the shotgun side of the business. From about 1863 up to the First World War, the firm made rook rifles for Holland & Holland. From the 1890s they supplied magazine rifles. In 1863 and 1864 the firm's address was given as 83-84 Weaman Street, but from late 1864 to 1875 their address was 84 Weaman Street. By 1874 the firm had a showroom in London at an unknown address. In 1875 the firm expanded into 82-84 and 88-89 Weaman Street. The shotgun is not in very good condition is unusable as a firearm and is not very significant historically or valuable, although made by a well known and respected manufacturer of firearms there are many better examples of shotguns made by P Webley and Son in collections and for sale. This particular example is of a standard pattern for utilitarian use of which many were made. Pin fire double barrel cartridge loading shotgun, the stock is of varnished walnut, the shotgun is in a wooden box, box has hinged lid and dovetail joints. Raised inscription on butt has an image of "dog carrying a bird in his mouth" and another image of a "anchor and chain". Inscribed to both sides of the locks "P Webley and Son", Maker's mark and proof marks for black powder shotguns on undersides of both barrels. Proof marks used are for Birmingham. flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, shotgun double barrel, double barrel, bird dog and bird, anchor and chain, webley & scott, pin fire, cartridge, philip webley

Seven copies of a letter from W. W. Eden, Mgr., F. W. Woolworth Co., dated November 12,1937 to Paul A. Douden & Co. He mentions that since installing the Scalebuoys over two years ago they have had no trouble with scale in the water systems where the Scale buoys were installed and they are contemplating installing in the water they used for cooling their natural gas engines. Since installing the scalebuoys there has been considerable savings on soap powders.sciences, instruments - general, scalebuoy, bill ashman collection - correspondence, f w woolworth co, paul a douden & co, w w eden

Set of three newspaper cuttings from The Argus - Students section. .1 - General Knowledge - has photos of 6 Victorian tramcars with notes - 3/5/1947 - has advert for Parsons Custard Powder on the rear. .2 - Travel - Tramways and Protests - about the derivation of the word tramways and railways and their development -6/5/1950. 3 - Australiana - Australia's first electric tram - details the Box Hill to Doncaster tramway with an image of the poster - 15/7/1950.trams, tramways, tramways, box hill, doncaster, tramcars

Hudson's Soap Powder, was the first satisfactory and commercially successful soap powder and was made in Liverpool by Robert Spear Hudson. He was also an innovator in using advertising, commissioning striking images from professional artists and paid for publicity , something which few other businesses did, and as such Hudson's soap became a household name. Horse, steam and electric tramcars, print periodicals and chemist shops carried his advertisements. This sign was manufactured by Patent Enamel Co Ltd was a company built in 1889 at Selly Oak, Borough of Birmingham, West Midlands, England, United Kingdom. The business was the first factory specifically devoted to enameled iron sign making. It had twelve furnaces for fusing the enamel, two scaling furnaces, and a large printing room, plus a huge area for steampipe drying. The company also smelted its own enamels and colour oxides. It is believed that the factory was decommissioned and demolished in the 1960's.the first factory specifically devoted to enameled iron sign making. It had twelve furnaces for fusing the enamel, two scaling furnaces, and a large printing room, plus a huge area for steampipe drying. The company also smelted its own enamels and colour oxides.The factory was decommissioned and demolished in the 1960s.The signage demonstrates the increasing demand for domestic soap products and new forms of advertising. The soap business was apart of the flourishing export trade between Australia and Britain during the height of the British Empire.Enamel advertising sign for Hudson's soapflagstaff hill, warrnambool, maritime museum, hudson's soap, advertising signage, patent enamel co ltd, selly oak, borough of birmingham, robert spear hudson

Photograph album, plastic and vinyl. Contains sixty coloured photographs of a National Trust tour of Heathcote and district. 7th and 8th November, 1998. Organized for the photographic committee by McIvor Historical Society. Photos include: Redesdale Presbyterian Church, Coliban Estate, Redesdale Hotel, Redesdale Bridge, Mia Mia Uniting Church, Spring Plains, Heathcote Hospital, Heathcote Powder Magazine, Moorabbee Ruins and grave C. Patterson, Derrinal, Mt Camel Homestead, Open Cut at Heathcote, Heathcote Church.national trust, properties, historic homesteads

Bendigo Tramways compiled by H Biggs. A short history of Bendigo's Tramways. Also some events and the year they happened. On the back is Early Bendigo Hotels, Compiled by L C Bennetts. Mentions the supply of liquor in the early days. Some early hotels were: The Criterion, The Royal, The Bendigo, The Black Swan, The Hibernian, The Sandhurst, The Freemasons (now the Courthouse), and The Shamrock. Also mentioned is Hazards of the Field including Mr Arblaster and his powder factory which had a few explosions, illness and accidents with cages.bendigo, history, long gully history group, the long gully history group - bendigo tramways, mr a o'keefe, the sandhurst and eaglehawk tramway company, j taylor, j hanson, electric supply company, coliban water supply, cr a harkness, constable thomas ryan, art gallery, miss broadfoot, victorian women's franchise league, ana hall, the bendigonian, law courts, post office, temperance hall, trades hall (old wardens court), roman catholic cathedral, shamrock hotel, bendigo philosophical society, bendigo fire brigade, mr arblaster, powder factory, meurer, sandhurst bee

Assay is a process of metallurgy and chemical analysis used to determine proportions of precious metals in ores and other metallurgy substances such as silver or gold. The process helps identify pollutants present within a sample and can indicate a high level of pollution in a mining site. Stoneware crucibles are used in the fire assay process due to their ability to withstand high temperatures. Fire assay is a three step process where by samples from the mine are ground in a find powder and then mixed with dry powder chemicals. This mixture is heated in a crucible to extreme temperatures (crucible fusion) until all of the powers fuse into a glass like slag. Once this reaction is complete, the contents are poured into a mold and cooled. In step three (known as cupellation) the mixture is separated in a fire assay cupel and once this is complete the cupel with reveal a small bead of precious metals. Established by George Guthrie in 1857 (about 5km north of its current site) and then again seven years later in 1864 after it initially closed, Bendigo Pottery remains one of the most influential and longest running potteries in Australia. Over the years the Pottery has contributed to the growth and development of the district through both its products including building products, table ware and decorative and commemorative war as well as artistically, being responsible for training and supporting many potters locally. It has partnered with the City on various tourism promotions and the Civic Collection holds a number of important items within its collection.Two stoneware vessels of differing dimensions (0287.1 & .2). Unglazed and porous, showing extensive signs of use. Stamped and marked on the outside. 0287.2 has a shaped pouring lip. Six smaller items, coins, buttons (0287.3,.4,.5,.6,.7,.8) were found with the crucibles but their relationship to the assay items is unknown.0287.1; Large crucible; Bendigo Pottery / E. 0287.2; Small crucible: Pottery / C Icity of greater bendigo commerce, city of greater bendigo mining, making a nation exhibition

Before mechanisation, pills were rolled by hand using equipment such as this pill press. Powders ingredients were blended together to form a resin, rolled and laid across the width of the platform. The paddle was then used to push the "sausage" shape through the grooves, creating a small, consistently sized and shaped, pill. The pill was then allowed to dry for later sale. This pill press is of uncertain origins but is representative of the type of equipment used to create pills in the 19th Century. It has the capacity to make 24 pills at once, and markings on the metal plate indicate each pill would have been the equivalent of "5 grains" (approx 0.3 grams).Rectangular wooden platform with a metal (brass) plate divided into 24 (twenty-four) grooves with a catchment area. The wooden paddle has two handles, one on each end, with a matching metal plate and grooves, as well as metal (brass) guide bars to help the paddle align with the platform.Handwritten on base of platform in black ink over white background: C11087 Handwritten on inside of guide bar on paddle in black ink over white background: C11087 Manufacturer's detail stamped into metal groove on platform: S. MAW SON / & / THOMPSON / LONDONpill press, pharmaceuticals, apothecary, pharmacy

Container (round flat box) of pink-coloured ('Peche') 'Cashmere Bouquet' Face Powder . Top of box ha Two razor strops. 'Gem' brand with attached metal clasp (opening clip); 'Malwa' brand with fixed clip; loose opening clip (from Malwa strop?). Shaped leather handle (detached) with the following in gold embossing - 'Specially Prepared'; '16' with surrounding wreath; map of Australia (with wreath). s product name and flower motif; back of box has manufacturer's details (Colgate Palmolive; Made in Australia etc.personal effects, shaving, razor strop