A coopers turning or bow saw is a woodworking tool used for straight or curved cuts. A bow saw is a type of frame saw with a thin toothed blade that is held in tension by a frame with two long narrow handles called "cheeks" that are supported and separated by a thin stretcher in the center of the handles, making a wide H shape (the cheeks form the uprights of the H, the stretcher the crossbar of the H). The blade is kept in tension with a turnbuckle that runs parallel to the blade between the two cheeks but on the opposite side of the stretcher.An age old tool used for cutting timber for hundreds of years before the modern cross cut saws were invented. This design of saw was part of a Coopers tool kit and used in the production of making barrels. However this item at this time cannot be associated with an historical event, person or place, provenance is unknown, item assessed as a collection asset as it is believed to have been produced before 1950.Bow saw wooden handle with metal bladeNonewarrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, bow saw, turning saw, coopers tools, cutting wood, sawing timber, coopering

A coopers turning or bow saw is a woodworking tool used for straight or curved cuts. A bow saw is a type of frame saw with a thin toothed blade that is held in tension by a frame with two long narrow handles called "cheeks" that are supported and separated by a thin stretcher in the center of the handles, making a wide H shape (the cheeks form the uprights of the H, the stretcher the crossbar of the H). The blade is kept in tension with a turnbuckle that runs parallel to the blade between the two cheeks but on the opposite side of the stretcher.An age old tool used for cutting timber for hundreds of years before the modern cross cut saws were invented. This design of saw was part of a Coopers tool kit and used in the production of making barrels. However this item at this time cannot be associated with an historical event, person or place, provenance is unknown, item assessed as a collection asset as it is believed to have been produced before 1950.Bow saw wooden handle with metal blade missingNonewarrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, bow saw, turning saw, coopers tools, cutting wood, sawing timber, coopering

A coopers turning or bow saw is a woodworking tool used for straight or curved cuts. A bow saw is a type of frame saw with a thin toothed blade that is held in tension by a frame with two long narrow handles called "cheeks" that are supported and separated by a thin stretcher in the center of the handles, making a wide H shape (the cheeks form the uprights of the H, the stretcher the crossbar of the H). The blade is kept in tension with a turnbuckle that runs parallel to the blade between the two cheeks but on the opposite side of the stretcher.An age old tool used for cutting timber for hundreds of years before the modern cross cut saws were invented. This design of saw was part of a Coopers tool kit and used in the production of making barrels. However this item at this time cannot be associated with an historical event, person or place, provenance is unknown, item assessed as a collection asset as it is believed to have been produced before 1950.Bow saw wooden handle with metal blade & frame tightening rodNonewarrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, bow saw, turning saw, coopers tools, cutting wood, sawing timber, coopering

The Bow Saw is considered by many to be the most satisfactory saw for cutting shapes since the narrow blade negotiates curves easily, and is held in tension. Both the handle and knob (at the other end of the blade) can be turned so that a cut can be made more or less parallel to the required cut. Obviously the blade must be free of twist when in use. It is available with blade lengths of 25 to 40 cm (10 to 16 in). Generally both hands grips the one handle, hence the bulbous shape with narrow neck, but when thick wood has to be sawn it is helpful to have a person at each side, both sides of the wood having been marked. In this way it is much easier to keep the cut square to the sides of the timber. The rivets holding the blade to the handle can be withdrawn so that the saw can be used for an internal cut, the blade being threaded through a hole drilled through the timber.A vintage bow saw used in cabinet work by a cabinet maker in the mid to later part of the 19th century probably made in England.Bow saw wooden frame and handles. Twine attached to upper section of frame.Noneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, bow saw, carpenders tools, cabinet makers tools, wood working, wood saw

Wooden bow saw for dove-tailing and tenon joints. Has handles for pulling the saw - one larger than the other. Blade is 28.5cm across. Tension is held by an animal gut product.Nonebow saw

Traditionally, a bow saw is a woodworking tool used for straight or curved cuts. A bow saw is a type of frame saw. Its thin blade is held in tension by a frame. In English and American vocabulary it denotes a toothed blade suspended between two long narrow handles called "cheeks" that are supported and separated by a thin stretcher in the centre of the handles, making a wide H shape (the cheeks form the uprights of the H, the stretcher the crossbar of the H). The blade is kept in tension with a turnbuckle or a twisted cord that runs parallel to the blade between the two cheeks but on the opposite side of the stretcher. If a cord is used, the cord is twisted with a toggle attached to one loop of the cord, adding tension. The toggle hits the stretcher, which keeps the cord from untwisting. A finer version of the saw uses a narrow blade (1/4" or less) with handles that allow the user to hold the saw and turn the blade. In this context it is also known as a turning saw[2] which is larger than a coping saw.Early settlers in Moorabbin Shire had to be self reliant and made their own clothes, tools and equipment as they established their market gardens and farms. A wooden Bow saw with tensioning string, toggle and bladetools, woodwork, metalwork, carpentry, pioneers, market gardeners, early settlers, moorabbin, cheltenham, bentleigh, ormond

Used in the late or early 20th Century. Could be used to cut steel.A curved steel shaped wooden handled Bow saw with a curved nail puller near the handle. A metal saw blade is attached by a screw at the end where it is fitted. Used in the late 19th or 20th Century.saws, carpentry tools, woodworking tools, tools, steel, wood, metal

Bow saw wooden frame with metal bladeflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, bow saw

Made and used by internees at Camp 3Handmade wooden frame, wooden centre strut across frame. Metal serrated edged blade. Later addition of twisted baling twine at top of saw.camp 3, tatura, saw

SHAPED WOODEN FRAME WITH SAW EDGE FOR PRUNING TREES OR CUTTING TIMBER. THE FRAME IS REINFORCED WITH METAL RODS THAT ALSO ADJUST THIS PIECE OF EQUIPMENT. ONE METAL ROD ACROSS THE TOPS STABILSES THE FRAME, ANOTHER ON AN ANGLE BRACES THE CENTRE WOODEN BAR. NONElocal history, trade, tools

Large metal saw with slightly curved sides and two wider cross pieces and a thin cross piece.trades, carpentry

Bow saw wooden frame and blade tensioned by a twisted cord and toggle stick. Blade has 8 points per inch. Toggle not original. 1710.1, 1710.2 & 1710.3-3 parts of itemflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, bow saw

Bow saw. Joiners Bow saw or Turning saw.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Bow saw wooden frame and handles. One handle longer than the other. Tension rod has wing nuts each end. 55cm(l) x 28cm (h)flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

A bucksaw is a hand powered frame saw similar to bow saw and generally used with a sawbuck to cut logs or firewood to length (bucking).Used by residents of the Kiewa Valley for clearing land, chopping firewood, cutting lumber. Also used while camping because it is portableFormerly UKV 239. Buck Saw with Lightning Tooth Blade. Operated by two men.Ref. Page 10 Tools for all Trade Catalogue. It consists of 3 horizontal bars, the top one being twisted wire and the bottom one being the metal blade with a wood bar in between. They are attached at each end to curved wooden bars. tool for wood, saw, buck saw

The Tabbara Sawmill was located at Brodribb River, at the lower Snowy River estuary. In the early 1900’s bow saws and broad axes were used to selectively log the forest. Ox driven carts pulled the logs to the Snowy River; the logs were floated downstream to the steam powered mill. The PS Curlip steamboat, transported the timber to growing townships, for schools, houses and farms. The mill closed in 1903. Knife and fork with steel blades and bone handles..Knife - Joseph Rodgers & Son Cuttlers to her Majestyknife fork cutlery domestic-item rodgers-joseph

Large Black and white photograph. White edges. Man seated on dining room chair in lounge room hold a bow and a saw. Man is wearing tweed style suit and glasses. Back of photo reads: Nimmy Matthews Saw Player. I32/G21A. Back is also stamped with Copyright of this photograph belongs to the Bendigo Advertiser. This photograph can only be reproduced with the permission of the Bendigo Advertiser.Bendigo Advertiserphoto, individual, nimmy mathews

Compass Saw, metal fine long bow. Wooden handle is brokenflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, compass saw, saw

The P.S. Alexander Arbuthnot was the last of the paddle steamers built at Koondrook, for the river trade in 1923. Owned by the Arbuthnot Sawmills. She was used to bring timber in from the forest to the sawmills to be processed from logs to timber. She was later owned by Evans Bros and then Barmah Charcoal Ltd. She sank at Yeilima, re-floated in 1973, placed on a low loader and taken to Shepparton for preservation. Echuca city council bought her for the Port of Echuca in April 1989. She was bought to Echuca in December 1991 to complete her restoration by shipwright Kevin Hutchinson. She is now used as a passenger vessel and is licensed to carry 47 passengers. The P.S. Alexander Arbuthnot is a reminder of the past life on the river. Being the last paddle steamer built for the river trade in 1923, the Alexander Arbuthnot is a reminder of the past life on the river. Licensed to now carry 47 passengers, she was used by the saw mills to bring timber in from the forests to the sawmills. A timber planked, monohull, side wheeled paddlesteamer with a 8hp horizontal Ruston Hornby steam engine. It has a flat bottom and mutiple decks. Currently painted cream with burgandy trim.Alexander Arbuthnot signage on wheelhouse and port and starboard bowp.s. alexander arbuthnot

HMAS Sydney was a Chatham class light cruiser of the Royal Australian Navy (RAN). Laid down in 1911 and launched in 1912, the cruiser was commissioned into the RAN in 1913. During the early stages of World War I, Sydney was involved in supporting the Australian Naval and Military Expeditionary Force, and escorting the first ANZAC convoy. On 9 November 1914, the cruiser defeated the German cruiser SMS Emden at the Battle of Cocos. During 1915 and 1916, Sydney operated on the North America and West Indies Station, before joining the 2nd Light Cruiser Squadron at Greenock, Scotland in November 1916. On 4 May 1917, the cruiser was involved in an inconclusive action against the German zeppelin L43; neither was damaged. During late 1917, Sydney became the first Australian warship to launch an aircraft, and the first warship to do so from a rotatable platform. After the war's end, Sydney spent a year in reserve before being reactivated to serve as Flagship of the RAN. The cruiser was decommissioned in 1928 and broken up for scrap. Several sections of the ship, including her bow and foremast, have been preserved as monuments, and three of the ship's main guns saw later use in shore fortifications.A number of these desk sets were manufactured and given to the Headmasters of selected schools throughout Australia in recognition of the efforts of school children in assisting the War effort during World War IMade from timber extracted from a companionway or staircase in the battle cruiser H.M.A.S. Sydney 2 x 5 cm.square glass containers are fitted. Blue attachment advising,wood from H.M.A.S. Sydney h.m.a.s. sydney, desk set, r.a.n

Cross cut saws have been used for millennia, but they came into wider usage in Europe from the 15th century onwards. The term 'cross cut' refers to the blades on the saw’s cutting edge which come in a variety of different patterns. These saws are specifically designed for cutting across the grain of the wood by timber workers, sawyers, and other land workers for tree felling and cutting up larger pieces of lumber into smaller more manageable pieces. The saws come in variable sizes and lengths and are designed for use by one or two people. With the two-man saws, a method of alternating 'pull and push' to drag the blade back and forth through the timber, maximising efficiency and labour division.Steel. Designed with bow in middle of blade. Small offset. Original ends in good conditions. No handles.churchill island, crosscut, saw, tool