Used to cut down trees and to saw the trunks to length. Used to clear the land.Used by the residents of the Kiewa Valley.A. Combination Tasmanian Pattern and Peg Tooth Cross Cut Saw B. Tasmanian Pattern Cross Cut Saw C. Peg Tooth Cross Cut Saw A crosscut saw is a saw designed for cutting wood perpendicular to (across) the wood grain. It cuts when pulled in both directions. The two man crosscut saw has wooden handles that fit into a steel socket at each end. The Tasmanian has a different tooth pattern to the Peg Tooth saw.crosscut saws, two man saws

Used by Wandin T SebireA forged steel 'M' toothed crosscut saw with wooden handles bolted on. It was used to saw rough wood or cross cut wood against the grain in the late 19th Century.'W' is stamped on the blade.hand tools, woodworking tools, carpentry tools, steel, hand saws, saws, cutting tools, crosscut saws

A Peg tooth forged steel crosscut saw with two wooden handles bolted on. It was used to saw rough wood or cross cut wood against the grain. It was used in the late 19th Century.hand tools, woodworking tools, carpentry tools, wood, steel, hand saws, saws, cutting tools, crosscut saws

Used in the 19th century.A forged steel narrow bladed double Peg and Rake toothed crosscut saw with no handles. It was used to saw rough wood or cross cut wood against the grain in the late 19th Century.Stamped on the saw: made of Simond Steel, Trade mark Reg. Warranted The Simond Saw Est 1832, Simond Steel & Saw co USA. Crescent Ground Steel Mill, Lockport New York. Factories Fitchburg Mass, Montreal Quebec No 325hand tools, woodworking tools, carpentry tools, steel, hand saws, saws, cutting tools, crosscut saws

Used by Edgar R Sebire.A Peg tooth forged steel crosscut saw with two wooden handles bolted on. It was used to saw rough wood or cross cut wood against the grain. It was used in the late 19th Century by Edgar R Sebire.hand tools, woodworking tools, carpentry tools, wood, steel, hand saws, saws, cutting tools, crosscut saws

A forged steel fine tooth crosscut saw with no handles. There are four rivet bolts and two round handle holders at each end of the saw. It was used to saw rough wood or cross cut wood against the grain in the late 19th Century.hand tools, woodworking tools, carpentry tools, steel, hand saws, saws, cutting tools, crosscut saws

A copy of a black and white photograph of two tree fellers sharpening a crosscut saw in the forest.A copy of a black and white photograph of two tree fellers sharpening a crosscut saw in the forest.marysville, victoria, australia, tree felling, tree feller, crosscut saw, photograph

The tips of each cutting tooth of a saw are bent (set) slightly away from the plane of the saw. Alternate teeth are set (and sharpened) in opposite directions. The set helps prevent the saw binding in the wood by cutting a kerf (the slot in the wood) that is slightly wider than the saw's thickness. Too little set and the saw binds; too much set results in more work to cut the wider kerf and could lead to too much side movement of the saw and a curving cut. The saw set gauge is used to measure the set of the saw tooth. The amount of set can be from almost nothing in dry hardwood to perhaps 1mm for some softwoods. The spider has three legs of the same length and a longer fourth leg. On a flat surface, the three short legs contact the surface while the long leg is just shy of the surface by the degree of 'set'. The spider is placed such that the three short legs are on the face of the saw with the longer leg touching the tip of the tooth - the tooth is bent to match the gauge.metal spiders used to set the teeth of crosscut sawsforests commission victoria (fcv), hand tools

Handle wooden for crosscut saw. Marked Spear and Jackson Ltd flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, crosscut saw, handle, spear and jackson ltd

Method of sawing trees in early days.Long metal saw tooth, saw with wooden handles used by two people. Crosscut sawsaw, tool, hand tool

This crosscut saw was originally part of the equipment on the barque Marjorie Craig, which brought New Zealand timber into Warrnambool from about 1908 to 1912 for the local merchants P J McGennan & Co. The toolbox was donated by a member of a local family connected with the La Bella rescue in 1905. The toolbox has carvings and markings that make it unique and connect it to the Marjorie Craig. The Craig Line of sailing ships was from Auckland, New Zealand, and traded in timber and some coal from New Zealand ports to Australia, including Sydney, Adelaide, Melbourne and Warrnambool. They returned with produce from Australia as ballast. In 1912 the Craig fleet included the Ihumata, Inga, Jessie Craig, Marjorie Craig, Louisa Craig and Joseph Craig. The steel barque Marjorie Craig, 500 ton, was built in 1891 as the 'Hirotha', in Ardrossan, Scotland for Norwegian owners. The ship was sold to Auckland’s Donald Ross and others in 1900, then in 1905 it was sold, registered by J.J. Craig in Auckland, New Zealand and renamed Marjorie Craig. Marjorie Craig’s commanders included Master R A Campbell in 1907, J MacFarlane in 1909 and Master R.G. Holmes in 1913. From February 1908, the Marjorie Craig was regularly seen in the Port of Warrnambool with loads of timber for merchants P J McGennan & Co. In February 1912 Marjorie Craig delivered white pine for P J McGennan & Co. In April of the same year, she brought 500,000 feet of timber for McGennan & Co and again in May 1912. On May 12 1912 Marjorie left the Port of Warrnambool with 500 tons of flour for New Zealand; it seems that this was her last time at Warrnambool. Prior to 1908, the vessel Speculant brought in timber from New Zealand for the McGennan firm. The Marjorie Craig had a strong reputation for being a ‘Fast Flyer’, breaking the sailing records for voyages between New Zealand and Australia. It was reported that she made passages with a speed equal to steamboats on several occasions. One of her records was from Warrnambool to Hokianga, NZ in eight-and-a-half days. The ship broke the record in October 1913 for the time from Adelaide to Auckland, sailing in 28 days, even with a damaged ship, and the owner presented Captain Holmes with a gold watch and chain. By the end of December 1913, the Craig Line’s last two surviving sailing ships, Marjorie Craig and Jessie Craig, had been purchased by Huddart, Parker & Co. Ltd. to work as coal hulks, one in Melbourne and one in Hobart.The saw is significant for being created for use in 1905 when the steel barque Marjorie Craig was purchased by J J Craig and given that name. The saw would be part of the sip's equipment and could have been used for the timber carried as cargo on the Marjorie Craig. The saw is significant for its association with the well-known Marjorie Craig, a frequent visitor to the Port of Warrnambool 1908 to 1912, a supplier of New Zealand timber for the local firm P J McGennan & Co, and one of the fastest inter-colonial sailing ships that broke numerous records for its speed including the fastest sailing from Warrnambool to Hokianga. Crosscut saw; blade attached to wooden handles by wingnut each end. The saw has 63 teeth. Also has a tag attached with an inscription. The saw was ship's equipment on the barque, Marjorie Craig.Handwritten on tab: "From sailing ship Marjorie Craig early 1900 Port of Warrnambool"flagstaff hill, maritime museum, maritime village, warrnambool, great ocean road, shiopwreck coast, woodworking tool, crosscut saw, shipwright tool, saw, marine trade, carpenter, marjorie craig, j j craig, craig line, 1905-1912

A tool to set the teeth of saws used in the early 20th centuryA metal guide used to set the teeth of a circular or crosscut saw when sharpening - i.e. to angle the teeth so that the saw bites into the wood.. It was used in the early 20th century.handsaws, woodworking saws, log saws, woodcutter saws

Crosscut saws are used to cut down trees and to saw the trunks to length. This is a two man cross cut saw. The two-man crosscut saw has wooden handles that fit into a steel socket at each end. The teeth are designed to enable both users to have equal strength.Orbost has historically been based on the timber industry and it remains an important but diminishing economic activity. Timber cutting tools are reminders of this history.A steel bladed cross cut saw with wooden handles that fit into a steel socket at each end. The blade has one straight edge and a toothed curved edge. saw timber cross-cut-saw tool

(a) Note by T.H. Kneen, "Interested observors are: Joseph Cade (Agrostology Branch), Rosemary Hamley 1951, Alison Howie 1951, students, one not identifiable. (b) Note by T.H. Kneen 8 April 1992, "The operator is George Manley - note the equipment - crow bar, crosscut saw, axe, sledgehammer, power driven crosscut saw."Black and white photograph. (a) Huge root ball with 4 people standing beside it. (b) Man working on large trunk of fallen tree. Chainsaw on wheels stuck? in the tree trunk, man holding a sledgehammer.(c) George Manley (Stockman) standing beside root ball.root ball, joseph cade, agrostology branch, rosemary hamley, alison howie, students, george manley, crow bar, crosscut saw, axe, sledgehammer, stockman, cypress tree, power driven crosscut saw

This is part of a crosscut saw raker/jointer/guage set used to bend the tip of each cutter tooth for cross cut logging saws. The logging saws used in the early 1900's for the clearing of forests required constant sharpening of their "cutting teeth". The logging of forested areas during these times was very much a "hands on" method of either one or two men by the use of saw or hand axe. This item was used by the surveyors commissioned by The S.E.C. Victoria Kiewa Hydro Electricity Scheme project mapping the relevant Alpine region. Chain saws, chain and ball(clearing) and bulldozing methods came in the mid 1900's.This particular saw sharpening method was used by surveyors laying down boundaries for the S.E.C. Victoria Hydro Electricity Scheme (1920's). This item was given to a local Kiewa Valley lad who accompanied the initial surveyors. The lad was responsible for the tendering and feeding of the surveyors "pack horses". Surveys work during this period and in these dense mountainous terrain of the Victorian Alps was both exhausting and hazardous. Overnight accommodation at various log cabins was not always possible and swag/tent alternative was the "fall back".This cast iron Spring Setting tool has a main body of angle iron contours with one end tappered into a flat circular extension with a slit (3/32" wide) running from the top to nearly the centre(15mm). This slit is to allow the bending of each "cutter tooth" of the cross cut saw. The "bottom of this slit has a semi circular ending. Protruding from one side of the bar body, and close to the "slit" is a tounge like extension (wedge) to fasten the spring set tool into a tree stump. See KVHS 0090 (A) for its Raker/Jointer saw sharpening guage set partner. Also see KVHS 0090 (C) for the associated wrench. On one side of the bar "DISSTON U.S.A."hand tool, saw, sharpening method, tree felling

Early settlers had to clear the land of trees and shrubs to establish and maintain their farms and market gardens. Some settlers worked in the Gippsland region felling timber for transport by bullock wagons to Melbourne. Two-man crosscut saws were primarily important when human power was used. Such a saw would typically be 1 to 4 m (4 to 12 feet) long, and sometimes up to 5 m (16 feet), with a handle at each end. The technique in using a two-man saw involved a sawyer standing at each end and together the sawyers would alternate pulling the saw through the wood. If the kerf -slit- began closing, causing the saw to bind, wedges would be inserted behind the saw blade in order to keep the kerf open.Two-man saws were designed to cut in both directions. Careful tooth design was necessary to clear the sawdust during the cut. This is a typical two-man tree felling saw that was necessary to clear the land when the pioneers were establishing their market gardens and farms in Parish of Moorabbin c1850A long steel blade saw with 2 wood handles c1900tools, saws, axes, early settlers, pioneers, market gardeners, dairy farms, orchards, vineyards, timber mills, bullock wagons, tree felling, timber mills, city of moorabbin, county of bourke, moorabbin roads board, parish of moorabbin, shire of moorabbin, henry dendy's special survey 1841, were j.b.; bent thomas, o'shannassy john, king richard, charman stephen, highett william, ormond francis, maynard dennis,

Albert (Abby) Trewin (b.21.03.1876 d. 01.07.1970) was part of the Trewin family who were early settlers at Jarrahmond near Orbost. Albert was born at Kingston near Ballarat, shifted to Jarrahmond where the house was called "Hillview", located 3 miles from Orbost on the B Road. The Trewin selection at Jarrahmond had many big trees on it and because these looked a bit like Jarrah trees from Western Australia, they names their property Jarrahmond (which became the district location and the name of Jarrahmond School). He cleared the land with bullocks, horses, crosscut saws, burned the stumps, burying some logs which were too big to burn. Then they milked cows, planted maize, had pigs, drove the pigs to Bairnsdale or to Waygara (c. 1915 when the train reached Waygara) on a buggy track through the bush. Pigs went to Dandenong Bacon Factory where they were processed into Dandy Ham. This photograph appears to be c.1950s - 1960s.A photograph of one of Jarrahmond's earliest settlers.B/W photograph of a man walking along a footpath. He is wearing a hat and has a walking stick in his right hand. He is wearing braces, white long-sleeved shirt, striped tie, glasses, polished black shoes. Behind him are vehicles and buildings (shops). jarrahmond, farming

The older lady in this photograph is Hazel Trewin, wife of Abby Trewin of Jarrahmond. The Trewins were a foundation settler/farmer family at Jarrahmond and many members of this family still live in this district. (2025). Albert (Abby) Trewin (b.21.03.1876 d. 01.07.1970) was part of the Trewin family who were early settlers at Jarrahmond near Orbost. Albert was born at Kingston near Ballarat, shifted to Jarrahmond where the house was called "Hillview", located 3 miles from Orbost on the B Road. The Trewin selection at Jarrahmond had many big trees on it and because these looked a bit like Jarrah trees from Western Australia, they names their property Jarrahmond (which became the district location and the name of Jarrahmond School). He cleared the land with bullocks, horses, crosscut saws, burned the stumps, burying some logs which were too big to burn. Then they milked cows, planted maize, had pigs, drove the pigs to Bairnsdale or to Waygara (c. 1915 when the train reached Waygara) on a buggy track through the bush. Pigs went to Dandenong Bacon Factory where they were processed into Dandy Ham. This photograph is significant because is of a member of the Trewin family of Jarrahmond.B/W photograph of two women standing. The older woman on the left hand side has her hand on a walking stick, and the other woman appears to be helping her and has her hand outstretched. Behind the two women is a bed an pillows. nonefarming, jarrahmond, trewin family

This spanner, part of a raker/jointer/guage set which is a sharpening tool for cross cut logging saws. The logging saws used in the early 1900's for the clearing of forests required constant sharpening of their "cutting teeth". The logging of forested areas during these times was very much a "hands on" method of either one or two men by the use of saw or hand axe. Chain saws, chain and ball(clearing) and bulldozing methods came in the mid 1900's.This particular spanner was part of a crosscut saw sharpening tool and method was used by surveyors laying down boundaries for the S.E.C. Victoria Hydro Electricity Scheme (1920's). This item was given to a local Kiewa Valley lad who accompanied the initial surveyors. The lad was responsible for the tendering and feeding of the surveyors "pack horses". Surveys during this period and in the dense mountainous terrain of the Victorian Alps was both exhausting and hazardous. Overnight accommodation at various log cabins was not always possible and swag/tent alternative was the "fall back"This small spanner is part of the Raker/Jointer Gauge saw set and is made from forged steel. The nut grip is of the two tightening nuts on the main construction frame. See KVHS 0090 (A &B) for the other items making up the sharpening tools.hand tool, saw, sharpening method, tree felling.

Used in the 1930s in the Forests Commission's Erica Forest District by a rigger for cutting the top off spar trees to be used in high-lead logging. The advent of crawler tractors after the Second World War brought about the end of high-lead logging. The saw was adopted in the 1940s by the-then Assistant Forester of Erica (James McKinty) for cutting firewood for domestic purposes; this use continued until about 1987. One-person cross cut saw with riveted handleforests commission victoria (fcv), hand tools