Austral 8 HP oil engine on 4 wheeled steel chassis with wrought iron wheels. Two double flywheels and flat belt pulley. Water cooled exhaust system at the crank end of the engine. Galvanised iron fuel tank slung under the engine. Painted green and black with red wheels.On an oval brass plate on the side of the engine :- "The Austral Oil Engine / Ronaldson Bros / Makers / No 663 / & Tippett / Ballarat Victoria"machinery ... engine ... oil ... metalwork

8HP Blackstone Lamps Start Oil Engine engine number 71076 Engine Details Maximum operating RPM of 240. Fitted with a 3'9" Flywheel Tested on the 6th of November 1908. Shipped to Cluter buck South Australia for installation on concrete base. Recovered and restored during the 80's in South Australia Purchased privately in 2013 in Tailem Bend South Australia and transported to Victoria. Currently on loan to the Puffing Billy Museum at Menzies Creek as an operating exhibit. Blackstone & Co. was a farm implement maker at Stamford, Lincolnshire, United Kingdom. In 1896 they built lamp start oil engines. The Lamp or hot-bulb engine (also hotbulb or heavy-oil engine) is a type of internal combustion engine. It is an engine in which fuel is ignited by being brought into contact with a red-hot metal surface inside a bulb, followed by the introduction of air (oxygen) compressed into the hot-bulb chamber by the rising piston. There is some ignition when the fuel is introduced, but it quickly uses up the available oxygen in the bulb. Vigorous ignition takes place only when sufficient oxygen is supplied to the hot-bulb chamber on the compression stroke of the engine. Most hot-bulb engines were produced as one-cylinder, low-speed two-stroke crankcase scavenged units Historic - Industrial - single cylinder, horizontal, 4 stroke, hot-bulb ignition oil engine Blackstone 8HP Oil Engine made from steel, wrought iron and brassOval Plate with Black Stones and Clutter Buck Brass Plaque engine number 71076blackstone, oil engine, clutter buck, black stone, puffing billy, hit and miss, engine, blackstone & co

Common in all service stations for engine oil top-up at pump service area by service station attendant.Before 'self serve' pump operations service station attendants 'serviced' the vehicle on the forecourt whilst filling with petrol, checking oil levels, water etc.Metal carry crate for 6 oil dispenser bottlesnoneshell, oil, oil bottle, oil crate, golden fleece, castrol, motor oil, engine oil

This is the first edition of the book, printed in 1899. It has since been reprinted with slight corrections in January 1900 and with correction in 1902. It is a textbook and reference book based on the study of steam, gas and oil driven machinery of the late 19th and early 20th century. The author, John Perry D. Sc., F.R.S., was born in 1850 and passed away in 1920. He was a Professor of Mechanics and Mathematics in the Royal College of Science, Vice-President of the Institution of Electrical Engineers, and Vice-President of the Physical Society. This book has significance as the First Edition of the book, published in 1899. The book is significant to the history, understanding and evolution of power driven machines. The principles apply to the machinery of the late 19th to early 20th centuries. The Steam Engine and Gas and Oil Engines: a book for the use of students who have time to make experiments and calculations Author: John Perry D.Sc., F.R.S. Publisher: Macmillan & Co Ltd, London Printed by Richard Clay and Sons, Limited, London and Bungay This is the First Edition of the book, printed in 1899 A hard cover book, red linen with black print. The Preface is written by the aughor on 22nd February 1899. The book contains many diagrams and tables as well as having reference numbers on many paragraphs in the chapters.Pencil on front endsheets "SJ 9""Rec. 371 a" Stamped in purple , front endsheet "F. ST. G. D. HOLYMAN" "L.4." Handwritten in ink "Richard G ---- / Liverpool --- P---ye"warrnambool, shipwrecked-coast, flagstaff-hill, maritime-museum, shipwreck-coast, book, the steam engine and gas and oil engines, john perry, reference book, scientific book, steam engines, gas engines, oil engines, combustion engines

When the numerous gold mines declined in production, the eucalyptus oil industry became an important source of work. The first eucalyptus oil producer in Bendigo was a chemist called Richard Sandner who operated a plant and refinery in Bridge Street from 1876. By 1900, many other distillers operated on the northern edge of Bendigo and in the Whipstick. In 1926, the Forest Commision established a eucalyptus distillery at Gunyah in Wellsford State Forest. See the Wellsford Forest Note for more information. Today, there are just two eucalypt distilleries operating in Bendigo. Most of the world’s eucalyptus oil is now produced overseas. Peter Ellis Collection: eight slides of Whirrakee Wattle regeneration near Bagshot, Eucalyptus History museum, Ruedin's Steam Traction engine, Eucalyptus oil condensor and a Mallee roller to rip out the eucalytpus trees. Peter was a chemistry lecturer at the Bendigo Institute of technology.history, bendigo, peter ellis collection, bendigo institute of technology, b.i.t., whipstick bendigo, bendigo state forests, eucalyptus oil, malle roller, whirrakee wattle, bagshot, steam traction engine, eucalyptus oil condensor

Bartram type AK, 5 HP horizontal cylinder water cooled magneto ignition oil Engine mounted on a metal and timber chassis with 4 wheels. It has its own cam driven water pump which pumps cooling water over metal gauze for evaporative cooling. Painted green. It has two flywheels, one at each end of the crankshaft, with a flat belt pulley attached to one flywheel. Cooling tank of galvanised steel with Bartram stencilled on one side. In working order.Cast nameplate on front of crankcase with a Bartram logo cast on also "Bertram / Type / AK"

Oil Can used for oiling machinery accurately - Engine oil can - Cone oil container - Tapered cylindrical applicator nozzle - Steel construction - Nozzle screws into placeNilmachinery, maintenance, technology, tools

The 1st edition of this famous work, giving an excellent account of the machinery used in late 19th century metal mining in the UK and overseas is very rare. It covers a wide range of equipment - pumps, steam engines, drills, winding engines, stamps & concentration mills, aerial ropeways, tramways and early uses of electricity etc. Brown hard cloth covered book. xvi 564 pages with additional advertisements, with over 300 illustrations and drawings, some fold out. Chapters include Water as a motive power, Wind engines and ventilating machinery, Steam boilers/engines and oil engines, hoisting machinery, draining of Mines, pumping engines, rock drilling machinery, boring machinery, concentration machinery, sizing and classifications trommels, joggers and jigging, fine concentration, milling of gold ores, milling of silver ores, amalgamation plates and machinery, dry and roasting machinery, chlorination and cyandide processes for the extraction of gold, electricity as a motive power for mining, electric lighting and blasting, aerial wire ropeways, transport by rail and road. There a a number of lovely line illustrations in the book including: Poncelot's undershot waterwheel; Fromont furnace;Victor turbine; Pelton waterwheel; Root's positive blower;Cross section and front elevation of Lancashire boiler; Robey's Compound Mill Engine; Portable Winding Plant; Iron Pit Head Gear ; Loading Arrangement in an Incline Shaft; kibble; Worthington Pump; California Pump; Scram's Air Compressor; Rock drill Bits; Special Sharpening tools; Boring tools;Rotating Picking table; Ore Feeder; roller crusher; stamp battery; round buddle; slime table; vanner; amalgamating plant; belt elevator;roasting furnace;splicing wire rope; capel; tipping waggon;mining, cornish pump, linkenbach table, water wheel, ventilation, oil engine, california, america, water, steam boilers, steam engines, oil engines, pumpimg, rock drilling, boring, jiggers, milling, silver, gold, drying and roasting, chlorination, cyaniding, lead, zinc, copper, electricity, electric lighting, wire ropes, transport, wind engine, poppet head

Zilles Printers was begun by Lewis Zilles in the early 1930s. It was in McKenzie Street Ballarat. His son Jeffrey also became a printer - letterpress, offset and screen printer. The business became Zilles Printers/Graphics and was in Armstrong Street and later Bell Street Ballarat. The Bulldog Engineering Company emerged around 1886. J Abraham began the operation building windmills and pumps. An employee, J F Osbourne, purchased the business when Abraham died in 1914. Windmills were still produced but Osbourne began to manufacture the "Bulldog" oil engine towards the end of the first world war. The Bulldog engine production was around 400. Of these there were 40 with wavy spokes. Some writer have been using Ballarat Bulldog as the brand name. This is incorrect, it was just Bulldog, made in Ballarat. Production ceased in the late 1920s.Coloured shield shaped decal design on white painted metal plate. Paper surround damaged.Bulldog Trade Mark. Manufactured by the Bulldog. Engineering Co Pty Ltd, Ballarat. Re No - 27,331zilles, bulldog engineering, ballarat, decal, j abraham, windmills, pumps, j f osbourne, bulldog oil engine, wavy spokes

Reginald (Reg) WARNOCK (1915-1991) Reginald William Warnock undertook the Commercial Art course during the 1930s. On completion, he worked as a designer at Paton’s Advertising Service, Melbourne. Commercial art subjects between 1915 and 1939 reflected changing practises and industry requirements, with Ballarat graduates in demand. In the 1936 Ballarat School of Mines Annual Report it was stated: "It is my pleasure to report a most successful year in the Technical Art School. I the Annual Poster Competition for Technical Schools, organised by Wiltshires Pty Limited, 16 prized valued at 33 pounds 8 shillings - out of 23 prizes valued at 56 pounds - were won by our students. R.W. Warnock moved from Ballarat to Moonee Ponds towards the end of March, 1937. This item is part of the Federation University Art Collection. The Art Collection features over 1000 works and was listed as a 'Ballarat Treasure' in 2007.Commercial art Framed original poster completed at the Ballarat Technical Art School by R.W. Warnock. It shows Oil pouring from a bottle in front of a steam engine. Please use the comment link below if you can assist with information about R.W. Warnock."For power and efficiency" "Mobil Oil"art, artwork, warnock, mobil, oil, poster, r.w. warnock, available, alumni, locomotive, steam engine, motor oil, advertisement, reginald warnock

Handwritten extracts, with typed copies, from the Bendigo Advertiser Monday July 24th, 1933. First erected for 20 years. Mr. Cook performs Opening. Approx. 400 people attended the opening on Sat 22nd. Expected that when run in, the ore will be crushed for 2/6 per ton. Consists of 10 heads, 1000 lbs each. Boxes are of Homestake pattern with wooden horses of special timber and iron guides. Copper plate tables of ample area provided. Floors are of concrete and so graded that all washings - -. Expected later to expand to 30 head. A 114 H P Ruston-Hornsby crude oil engine is provided with a friction clutch to facilitate easy starting and will be capable of driving the battery when it is extended. Those who attended the opening were subsequently the guests of the Company at light refreshments. Copied 1/7/1970. Albert Richardson Collection gold mining, miners' safety cage, little 180 battery, mr cook, bendigo advertiser, 114 h p ruston-hornsby crude oil engine

Digital Image of MMTB trams W7 1029 and 1030 passing each other at the corner of Spring and Bourke St, with Parliament house in the background. Both trams are running route 96, East Brunswick - Spencer St services. 1029 has adverts for BIC pens, Bisto gravy mix and engine oil. 1030 has adverts for Fosters Lager and Tiger Paw tyres. Photo by Dave Macartney 1969?trams, tramways, w7 class, bourke st, spring st, parliament, tram 1029, tram 1030

Colour slide of L 102, northbound, leaving High Street St Kilda at St Kilda Junction, running a route 4 service. The tram has adverts for Dutor valves and Booses engine oil additive. In the background are R T Taylor licensed grocer, Brookes Bros, the Junction Hotel advertising Rothmans, Dunlop tyres, and Wynvale Flagons. Some roadworks are taking place on the right-hand side.Yields information about St Kilda Junction and tram 102Kodachrome colour slides, cardboard mount, duplicate.Has "MP102" in pencil and stamped "Tramways Museum Society Victoria" on rear.tramways, l class, tram 102, st kilda junction, trams, route 4

Three auction catalogues of a sale at the Bendigo Municipal Quarries, Axedale on 2nd September, 1941 of Surplus Machinery, Plant, Buildings and Equipment comprising Crude Oil Engine, Diesel Engine, air Receiver, Crude Oil Tank, Stone Hoppers Buildings, etc. J. H. Curnow & Son were the auctioneers.business, auctioneers, j h curnow & son pty ltd, ian dyett collection - auction catalogue - bendigo municipal quarries - axedale, j h curnow & son, j l jamieson & co, the cambridge press

The slush lamp is thought to have been used for examining and oiling train engines.The slush lamp has local significance as it was donated by a resident of Wodonga. It also has historic significance as an example of an object made by upcycling in the c. late 19th century and early 20th century.The slush lamp consistis of a rectangular grey metal body with soldered edges with a flat handle at one end, a fibrous textile wick protruding from a long spout at the other end, and a cork inserted in the opening on the top surface to secure the fuel used. Slush lamps are defined as "improvised lights made from a container of fat and a wick", originating in the mid-19th century. slush lamp, slush lamps, improvised lamps

Bendigo Advertiser "The way we were" from Tuesday, July 6, 2004. Puffin' stuff: the first oil engine in Charlton was used on Mr Fred Judd' property at Teddywaddy. In this particular operation the engine is being used to cut chaff.newspaper, bendigo advertiser, the way we were

The origins of the humble handheld driptorch have been lost in time. They are widely used for ignition in controlled burning operations in forest and grasslands. The date, origins and manufacturer of this particular model are unknown. The “Pacific Forester“ with its short central wand and somewhat leaky ball-valve was made by the American Wajax company in the 1940s. The Pacific Forester is slightly different in design from the more robust and common “Panama” driptorch first manufactured in 1933 and used extensively by Queensland cane farmers. The Panama is closely related to the current “Firebug” used in Victoria which is manufactured by Rodney Industries in Brisbane. The fuel is a mixture of petrol and diesel and every FCV District had their own closely-guarded secret formula ... 2:1, 3:1, 1:1, 4:1 or 3:2 ratio. There was also the choice of 91, 95 or 98 octane petrol mixed with summer or winter diesel. Occasionally some of the old Avgas or Jet-A1 lying around the depot was added with a splash of engine oil to make the mixture stick to the fuel to be ignited. The fuel mixed also varied between autumn or spring, heathland, mixed forest, or high-intensity slash burnsEarly driptorch designDrip torch with handle Wand has loop and valve. The loop is designed to assist with even flow of fuel which flows out onto the burning head of the wand. Soldered tin fuel container which holds burner mix. Gravitational feed of the driptorch allows the unit to drip fire, making it simple and quick to operate. bushfire, forests commission victoria (fcv)

The origins of the humble handheld driptorch have been lost in time. They are widely used for ignition in controlled burning operations in forest and grasslands. The “Pacific Forester“ with its short central wand and somewhat leaky ball-valve was made by the American Wajax company in the 1940s. The Pacific Forester is slightly different in design from the more robust and common “Panama” driptorch first manufactured in 1933 and used extensively by Queensland cane farmers. The Panama is closely related to the current “Firebug” used in Victoria which is manufactured by Rodney Industries in Brisbane and has an offset wand design which gives it good balance. The fuel is a mixture of petrol and diesel and every FCV District had their own closely-guarded secret formula ... 2:1, 3:1, 1:1, 4:1 or 3:2 ratio. There was also the choice of 91, 95 or 98 octane petrol mixed with summer or winter diesel. Occasionally some of the old Avgas or Jet-A1 lying around the depot was added with a splash of engine oil to make the mixture stick to the fuel to be ignited. The fuel mixed also varied between autumn or spring, heathland, mixed forest, or high-intensity slash burnsCommon driptorch used throughout AustraliaDrip torch with handle Wand has loop and valve. The loop is designed to assist with even flow of fuel which flows out onto the burning head of the wand. Pressure equalising value in top of aluminum fuel container which holds 4 litres of burner mix. Gravitational feed of the driptorch allows the unit to drip fire, making it simple and quick to operate. Instructions for use. CF+L written with texta pen.bushfire

The origins of the humble handheld driptorch have been lost in time. They are widely used for ignition in controlled burning operations in forest and grasslands. The “Pacific Forester“ with its short central wand and somewhat leaky ball-valve was made by the American Wajax company in the 1940s. The Pacific Forester is slightly different in design from the more robust and common “Panama” driptorch first manufactured in 1933 and used extensively by Queensland cane farmers. The Panama is closely related to the current “Firebug” used in Victoria which is manufactured by Rodney Industries in Brisbane and has an offset wand design which gives it good balance. The fuel is a mixture of petrol and diesel and every FCV District had their own closely-guarded secret formula ... 2:1, 3:1, 1:1, 4:1 or 3:2 ratio. There was also the choice of 91, 95 or 98 octane petrol mixed with summer or winter diesel. Occasionally some of the old Avgas or Jet-A1 lying around the depot was added with a splash of engine oil to make the mixture stick to the fuel to be ignited. The fuel mixed also varied between autumn or spring, heathland, mixed forest, or high-intensity slash burnsKerosene drip torch Short wand no valveBCR Holdingsforests commission victoria (fcv), planned burning, bushfire

The origins of the humble handheld driptorch have been lost in time. They are widely used for ignition in controlled burning operations in forest and grasslands. The “Pacific Forester“ with its short central wand and somewhat leaky ball-valve was made by the American Wajax company in the 1940s. The Pacific Forester is slightly different in design from the more robust and common “Panama” driptorch first manufactured in 1933 and used extensively by Queensland cane farmers. The Panama is closely related to the current “Firebug” used in Victoria which is manufactured by Rodney Industries in Brisbane and has an offset wand design which gives it good balance. The fuel is a mixture of petrol and diesel and every FCV District had their own closely-guarded secret formula ... 2:1, 3:1, 1:1, 4:1 or 3:2 ratio. There was also the choice of 91, 95 or 98 octane petrol mixed with summer or winter diesel. Occasionally some of the old Avgas or Jet-A1 lying around the depot was added with a splash of engine oil to make the mixture stick to the fuel to be ignited. The fuel mixed also varied between autumn or spring, heathland, mixed forest, or high-intensity slash burnsKerosene drip torch Long straight wand with control valveBell Backburnerforests commission victoria (fcv), planned burning, bushfire