INSULATED wagon. Built in 1899 and numbered 1, it was the only one of its type built Service History : NTT In October 1899 a bogie insulated van was built and placed into traffic. In 1926, the class was relettered to NT. Obtained by the Puffing Billy Preservation Society By 1969, the vehicle was in the Menzies Creek Museum. Currently Located at Belgrave Station The NT is an insulated van. The wooden body (both sides and roof) was insulated with cowhair. It had two swinging doors either side in the middle, as have the NU vans. The van was painted white, in an attempt to reflect the summer heat. There was only one built for the narrow gauge lines. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 7 tons Capacity 10 tons Built 1899 Number Built 1 In use none To be restored 1Historic - Victorian Railways - Narrow Gauge Rolling Stock - Insulated Wagon 1NT Victorian Heritage Register (VHR) Number H2187 Puffing Billy Locomotives and Rolling Stock Collectiontimber constructed body wall cavity filled with horse hair for insulation The NT is an insulated van. The wooden body (both sides and roof) was insulated with cowhair. It had two swinging doors either side in the middle, as have the NU vans. The van was painted white in an attempt to reflect the summer heat. There was only one built for the narrow gauge.1nt1nt, puffing billy, insulated van

An insulated stainless steel cups with black plastic cover and handle. university of ballarat, cup, merchandise

.1 - Report - A4 sheet colour copy titled "Safety Alert 2013-001, Insulated Tram", describing the investigation into an incident on 11/1/2013 at the Melbourne University terminus received an electric shock due to an insulated tram as a result of sand build up. Details procedures for such events, the incident, the investigation and recommendations. .2 - Report - A4 sheet, colour titled "Safety Alert Tram to Tram collision" reporting on collisions during 2018, 10 to mid May 2018, compared to 7 for 2017. Has a photo of tram 168 and 226 in collision. Signed by Terry Scott, Director of Lines, issued 18/5/2018.trams, tramways, yarra trams, incidents, melbourne university, sanding equipment, electricity, collision

.1 - Book - 28 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Contactor Starters for Electric Motors" C49-1927, December 1927. .2 - Book - 56 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Dimensions of insulated annealed copper conductors for electric power and light including voltage tests" C50-1928, June 1928. .3 - Book - 36 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Vulcanised Fibre for Electrical Purposes" C51-1928, May 1928. .4 - Book - 16 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Bus-bars and connections constructed of bare copper or aluminium" C52-1928, May 1928. .5 - Book - 16 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Fixed Condensers for Radio Reception Purposes" - C53-1928, February 1928. .6 - Book - 32 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard "Graphic (Recording or chart recording) ammeters, voltmeters and wattmeters." C54-1928 March 1928. .7 - Book - 20 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "5-Amp two pin wall plugs and sockets for domestic purposes (without earthing connection)" C55-1928, August 1928, .8 - Book - 24 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard "Electric Cable Soldering Sockets" C56-1929, March 1929. .9 - Book - 8 pages + brown covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Australian Standard "Graphical Symbols and Schedule of Outlets for the Electrical Equipment of Buildings" C64 and 65-1935, October 1935. .10 - Book - 24 pages + brown covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Australian Standard "Porcelain Insulators for overhead powerlines and outdoor switching Structures" C67-1939, August 1939. On top right hand corner has the date stamp of the "The Electric Supply Co. of Victoria Ltd Ballarat" for items .1 to .8, SEC stamp on .10. trams, tramways, power station, standards, materials, electrical systems

.1 - Book - 8 pages + grey covers, side stapled, issued by the Australian Standards Association, "Electrical Voltages and electrical frequencies for new installations ", C1 (a&b) - 1926, December 1926. .2 - Book - 36 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Overhead Line wire material for telegraph and telephone purposes", C3-11-1925, November 1925. .3 - Book - 20 pages + brown covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Telephone cable, paper insulated lead covered", C12 - 1928, January 1928. .4 - Book - 24 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Marking for Switchboard bus-bars and connections" C13 - 1925, December 1925 - with a pasted green label noting that the "tentative standard is now endorsed as Australian Standard without amendment" - dated Oct. 1930. .5 - Book - 32 pages + grey covers, side stapled, issued by the Australian Standards Association, Tentative Australian Standard "Dimensions and Resistances of Bare Annealed Copper Wire for Electrical Machinery and Apparatus", C 18-1926, October 1926. .6 - Book - 12 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard "Slate Slabs for Electrical Purposes", C19 - 1926, July 1926. .7 - Book - 16 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Moulded Flat Top Insulation Bushes" C20-1926, October 1926. .8 - Book - 16 pages + brown covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Australian Standard "Insulation dimensions and resistance of enamelled plain copper wire for instruments and apparatus" C21-1928, January 1928. .9 Book - 20 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Watertight Glands for electric cables" C22-1926, September 1926. .10 - Book - 20 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Air-break knife switches and laminated brush switches for voltages not exceeding 660Volts" - C23 - 1926, August 1926" On top right hand corner has the date stamp of the "The Electric Supply Co. of Victoria Ltd Ballarat" trams, tramways, power station, standards, materials, electrical systems

This series of photos depicts appliances and equipment kept within easy reach in a kitchen. The photos, date-stamped "89 1 5", were taken during a visit to the home of Arthritis Foundation of Victoria member, Margaret. They were taken to accompany an article by Occupational Therapist, Pat Dwyer. Titled, 'Suggestions for independent living', the article and accompanying photo appear on page 10 of the Vol 2 No 1, March 1989 issue of the Arthritis Foundation of Victoria's quarterly magazine, Arthritis Update. It outlines the steps taken by Margaret to facilitate the daily challenges of living independently with arthritis. This photo depicts an insulated teapot and some kitchen canisters with 'drop-in' lids, amongst other items on a kitchen table. However, this particular photo was not published.B&W photo of an insulated teapot and some kitchen canisters amongst various other items on a kitchen table. The photo is date-stamped "89 1 5" in white text on the bottom left side of the image layer.[In blue ink on a yellow sticky note] Insulated teapot and canisters with drop in lids.arthritis foundation of victoria, afv, rheumatism and arthritis association of victoria, raav, pat dwyer, occupational therapist, ot, arthritic aids, kitchen aids, kitchen gadgets, insulated teapot, kitchen canisters, food storage, pantry storage containers, drop-in lids, living with arthritis, living independently, pain management, arthritis update, 1989

Insulated steel box containing two lidded food tins and five hexamine stovesFood Container Insulated With Inserts. US Knapp Monarch Cohot box, hexamine stove

These mugs are souvenirs of the Warrnambool Woollen Mill. They were either sold as souvenirs or given to clients of the mill. The Warrnambool Woollen Mill in South Warrnambool was opened in 1910 with the first manager being John Bennett, an Englishman who recruited skilled weavers and bought mill equipment from his home country. At the height of production the mill was employing up to 700 people. In 1958 the mill became the first in Australia to manufacture electric blankets. In 1968 the mill was sold to the Dunlop company and in the ensuing years various companies owned the plant. In the year 2000 the mill was closed and the equipment was sold. The buildings were sold to a private developer and the first residents moved into the new housing estate in 2009. These mugs are of interest as mementoes of the Warrnambool Woollen Mill, a key industry in the development of Warrnambool and one that operated for 90 years. .1 This is an insulated plastic mug with a mottled orange-coloured body and a white rim on the top opening and a white handle. On the side of the mug is a printed name with gold lettering on a brown background. The maker’s name is etched into the base of the mug. .2 This is an insulated plastic mug with a purple and black mottled body and a white rim on the top opening and a white handle. On the side of the mug is a printed name on a brown background with gold lettering. The maker’s name is etched into the base of the mug. .1 & .2 Warrnambool Fabrics Blankets Steditemp Insulated Ware Made in Australia by Newlyne MFG Co Pty Ltd Division of J. Glaser & Co Melbourne warrnambool woollen mill

Mrs. Potts invented the Potts Removable Handle Iron. Her invention of the Cold Handle Sad Iron changed the clothing iron industry. The detachable insulated handle was designed to be always cool for ironing. The handle was detachable, so that several irons could be on the stove at one time and the handle swapped between several bodies.This item is an example of an invention that was universally adopted because it meant that users could keep several irons on the stove at one time and the handle swapped when needed. The original Mrs Potts irons had handles made of wood (walnut) and this enabled the user to us the iron without sustaining burns.A Mrs Potts Sad Iron.It is a double point design with detachable handle. The detachable insulated handle was designed to be always cool for ironing. The handle was detachable, so that several irons could be on the stove at one time and the handle swapped between several bodies. There is no handle with this iron. MRS POTTS. Rest is indecipherable.domestic-appliance mrs-potts sad-iron flat-iron laundry

Transformer with switchable voltage. Voltage ranges from 110 to 240. This means it can be in different countries. It has a 6 volt input for light/lamp. Made in 1940s. The core of the transformer is laminated steel, each layer insulated to stop from over heating. The transformer is still in working order.Transformer with switch for different voltage settings. Globe connected to unit. Universal transformertransformer, switch, voltage, light, laminated steel, insulated, switchable, universal

Insulated bottle holder, blackequipment, afghan, army

DEFINITION microfarad Posted by: Margaret Rouse WhatIs.com Contributor(s): Kenda, Jack Clements The microfarad (symbolized µF) is a unit of capacitance, equivalent to 0.000001 (10 to the -6th power) farad. The microfarad is a moderate unit of capacitance. In utility alternating-current (AC) and audio-frequency (AF) circuits, capacitors with values on the order of 1 µF or more are common. At radio frequencies (RF), a smaller unit, the picofarad (pF), is often used. This unit is equal to .000000000001 (10^-12) µF. In RF scenarios, capacitances range from about 1 pF to 1,000 pF in tuned circuits, and from about 0.001 µF to 0.1 µF for blocking and bypassing. At audio frequencies (AF), capacitances range from about 0.1 µF to 100 µF. In power-supply filters, capacitances can be as high as 10,000 µF. Capacitor, 1/3 M.F.D. (microfarad) within wooden insulating box. Two terminal posts set in an insulating box. Maker's name and place 1/3 M.F.D No. 34402scientific instrument, capacitor, electrical engineering, laboratory

The B I Hand-Book by British Insulated Cables Fly page has stamp that reads F. ST. G. D. Ho;yman insdie front cover hand written reads "Richard A. Golding - April 1927" warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, shipwrecked-artefact, book, the b i hand-book, british insulated cables

Insulated metal container holding three lidded containersUS Contr No: DSA-400-67-C-6040-TR503food container, hot box

Insulated metal container holding three separate lidded containersUS Wyott Corp. chey. WYO 1976. DSA-400-76-C-3932food container, hot box

After a post war migration population boom in Sunshine North and surrounding areas, the Albion North State School (Now Albion North Primary School) opened on the 3rd July 1962.This Commentative Coffee Cup celebrates 60 years since the school opened in 1962.Aluminum insulated coffee cup and lid with text printed on the sideAlbion North Primary School 1962 - 2022albion north primary school, furlong road, sunshine north, albion north state school

Belonged to Aunt of donor. the late Mrs Myrtle Bennett 122 Thames Street Box Hill. She resided there from November, 1939, immediately after her marriage until her death on 27th February 1997.Round yellow plastic machine with white pliable tubing attached to machine at one end and at the other attached to a large yellow and white 'bonnet' with air holes. Electric plug. Contained in a yellow Vinyl case.General Electric Off --- speed dry. Model MD18 703 240 volts --- double insulated.personal effects-toilet requisites, cosmetics

History of the Loch Ard: The Loch Ard got its name from ”Loch Ard” a loch which lies to the west of Aberfoyle, and the east of Loch Lomond. It means "high lake" in Scottish Gaelic. The vessel belonged to the famous Loch Line which sailed many vessels from England to Australia. The Loch Ard was built in Glasgow by Barclay, Curdle and Co. in 1873, the vessel was a three-masted square-rigged iron sailing ship that measured 79.87 meters in length, 11.58 m in width, and 7 m in depth with a gross tonnage of 1693 tons with a mainmast that measured a massive 45.7 m in height. Loch Ard made three trips to Australia and one trip to Calcutta before its fateful voyage. Loch Ard left England on March 2, 1878, under the command of 29-year-old Captain Gibbs, who was newly married. The ship was bound for Melbourne with a crew of 37, plus 17 passengers. The general cargo reflected the affluence of Melbourne at the time. Onboard were straw hats, umbrella, perfumes, clay pipes, pianos, clocks, confectionery, linen and candles, as well as a heavier load of railway irons, cement, lead and copper. There were other items included that were intended for display in the Melbourne International Exhibition of 1880. The voyage to Port Phillip was long but uneventful. Then at 3 am on June 1, 1878, Captain Gibbs was expecting to see land. But the Loch Ard was running into a fog which greatly reduced visibility. Captain Gibbs was becoming anxious as there was no sign of land or the Cape Otway lighthouse. At 4 am the fog lifted and a lookout aloft announced that he could see breakers. The sheer cliffs of Victoria's west coast came into view, and Captain Gibbs realised that the ship was much closer to them than expected. He ordered as much sail to be set as time would permit and then attempted to steer the vessel out to sea. On coming head-on into the wind, the ship lost momentum, the sails fell limp and Loch Ard's bow swung back towards land. Gibbs then ordered the anchors to be released in an attempt to hold its position. The anchors sank some 50 fathoms - but did not hold. By this time the ship was among the breakers and the tall cliffs of Mutton Bird Island rose behind. Just half a mile from the coast, the ship's bow was suddenly pulled around by the anchor. The captain tried to tack out to sea, but the ship struck a reef at the base of Mutton Bird Island, near Port Campbell. Waves subsequently broke over the ship and the top deck became loosened from the hull. The masts and rigging came crashing down knocking passengers and crew overboard. When a lifeboat was finally launched, it crashed into the side of Loch Ard and capsized. Tom Pearce, who had launched the boat, managed to cling to its overturned hull and shelter beneath it. He drifted out to sea and then on the flood tide came into what is now known as Loch Ard rd Gorge. He swam to shore, bruised and dazed, and found a cave in which to shelter. Some of the crew stayed below deck to shelter from the falling rigging but drowned when the ship slipped off the reef into deeper water. Eva Carmichael a passenger had raced onto the deck to find out what was happening only to be confronted by towering cliffs looming above the stricken ship. In all the chaos, Captain Gibbs grabbed Eva and said, "If you are saved Eva, let my dear wife know that I died like a sailor". That was the last Eva Carmichael saw of the captain. She was swept off the ship by a huge wave. Eva saw Tom Pearce on a small rocky beach and yelled to attract his attention. He dived in and swam to the exhausted woman and dragged her to shore. He took her to the cave and broke the open case of brandy which had washed up on the beach. He opened a bottle to revive the unconscious woman. A few hours later Tom scaled a cliff in search of help. He followed hoof prints and came by chance upon two men from nearby Glenample Station three and a half miles away. In a complete state of exhaustion, he told the men of the tragedy. Tom then returned to the gorge while the two men rode back to the station to get help. By the time they reached Loch Ard Gorge, it was cold and dark. The two shipwreck survivors were taken to Glenample Station to recover. Eva stayed at the station for six weeks before returning to Ireland by steamship. In Melbourne, Tom Pearce received a hero's welcome. He was presented with the first gold medal of the Royal Humane Society of Victoria and a £1000 cheque from the Victorian Government. Concerts were performed to honour the young man's bravery and to raise money for those who lost family in the disaster. Of the 54 crew members and passengers on board, only two survived: the apprentice, Tom Pearce and the young woman passenger, Eva Carmichael, who lost her family in the tragedy. Ten days after the Loch Ard tragedy, salvage rights to the wreck were sold at auction for £2,120. Cargo valued at £3,000 was salvaged and placed on the beach, but most washed back into the sea when another storm developed. The wreck of Loch Ard still lies at the base of Mutton Bird Island. Much of the cargo has now been salvaged and some items were washed up into Loch Ard Gorge. Cargo and artefacts have also been illegally salvaged over many years before protective legislation was introduced in March 1982. One of the most unlikely pieces of cargo to have survived the shipwreck was a Minton majolica peacock- one of only nine in the world. The peacock was destined for the Melbourne 1880 International Exhibition in. It had been well packed, which gave it adequate protection during the violent storm. Today the Minton peacock can be seen at the Flagstaff Hill Maritime Museum in Warrnambool. From Australia's most dramatic shipwreck it has now become Australia's most valuable shipwreck artifact and is one of very few 'objects' on the Victorian State Heritage Register. The shipwreck of the Loch Ard is of significance for Victoria and is registered on the Victorian Heritage Register ( S 417). Flagstaff Hill has a varied collection of artefacts from Loch Ard and its collection is significant for being one of the largest accumulation of artefacts from this notable Victorian shipwreck. The collections object is to also give us a snapshot into history so we can interpret the story of this tragic event. The collection is also archaeologically significant as it represents aspects of Victoria's shipping history that allows us to interpret Victoria's social and historical themes of the time. The collections historically significance is that it is associated unfortunately with the worst and best-known shipwreck in Victoria's history. Silver plated Serving Dish, insulated, with two layers of copper alloy. Noneflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Blow Torch, brass with insulated wound handle with small hand pump.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Porcelain Insulating Shield, early make, has rested over a sooty burner

Toledo Thermal Cooker - wooden box on legs with aluminium insulated centre. Cookpot fits on top. Hook includedsee photoscooking, thermal, toldedo, cooker

Frank Mashek Co. Chicago ILL.

The pith helmet was worn to shade the head in hot and humid climates. Owned by donor's father when he was mining mica in the 1930s; not worn because of embarrassment.Light brown insulated hat, designed as protective covering for the head against the sun; red and green cloth lining, leather sweat band and chin strapGilt inscription on lining: "Real solapith, made in India expressly for the Myer store for men, Melbourne & Adelaide" [size] 6 7/8pith helmet, hats, headwear

This teapot was donated to the Historical Society and placed in the Miner's Cottage display where it remained for several years. It was removed for cleaning and put in an archives display cabinet. The miner's cottage burnt down and thus the teapot is the only remaining object from the site.Teapot made of Britannia metal. Oval with recumbent dog on top. Insulated handle. Brilliant cut design on sides. Pouring spout and '7' shaped handle.On base: 8 Warranted best Britannia metal. Sheffield. 1204

Equipment issued to all Army Soldiers as part of original kit. Kit belong to CAPTAIN Brian CLEREHAN VX91862. Enlisted 29 March 1943 age 26 years, discharged 17 July 1946 with the rank of Captain in 2nd New Guinea Infantry Battalion..1) One litre water bottle with cork lid, insulating felt cover. Cork attaches by string to the felt cover. And also in a cotton webbing carrier. Made up of vertical and horizontal straps wth a brass studs, 2 brass buckles to attach to shoulder straps .2) One litre blue enamelled bottle with attached cork lid and insulating felt cover. No webbing included .infantry, water bottle, 2nd new guinea infantry battalion

This silver-plated teapot is characteristic of late Victorian to Edwardian British metalwork (c. 1880–1910), likely manufactured in Britain using electroplated nickel silver (EPNS) or Britannia metal (EPBM). Its design reflects the influence of the British Aesthetic Movement, and it was likely used in Beechworth, Victoria. The teapot could be emblematic of the riches amassed in Victoria during the gold rush period and the subsequent luxuries enjoyed by some as a result. The social history objects held in the Burke Museum's collection help to tell the stories of Beechworth's past by showing the social, cultural, and economic aspects of the town's history.An ornate silver-plated teapot with embossing and engraving depicting a fence and floral designs. Architectural handle fitted with heat-insulating spacers (likely bone, ivory, or bakelite).Silver marks 4386 6 BMM5279teapot, kitchenware, silverware, vandenberg