Acquired from staff member Brett Hough who used it as a teaching aidModel of a small chainsaw with one side cut away to show the inside. McCulloch Superpro 125C TM. Used for teaching Arboriculture.Chainsaw Shop Kinleith, State Training, Cutaway, Prepared by Graham Cocks 1976chainsaw, model chainsaw, cutaway, arboriculture, teaching

Continuous cutting chain was patented in 1905 by Samuel Bens of San Francisco, while the first portable chainsaw was developed and patented in 1918 by Canadian millwright James Shand. But the main advancements of modern petrol chainsaws occurred in Europe in the 1920s and 30s where Andreas Stihl is often hailed as the "father of the chainsaw" After the second world war lighter materials, metal alloys and improved engine designs revolutionised the logging and timber industry. Of interest on this model is the spacing of the teeth compared to modern machines. With a 4HP motor it has few safety features and is very heavyEarly model chainsawBurns ChainsawModel 106forest harvesting

Early model Stihl chainsaw with a gravity fed swivel carburetor. Painted grey and black, rear shield unpainted aluminium. Red plate fixed to side with name and specifications.On red plate Sthil logo, "A. Sthil, Maschinenfabrik /Waiblingen Neustadt / Type BL Motor Nr 55101 / Leistung 5.5 PS Nrehzahl 4000 / Nubraum 125 ccm Daujahr F / Zur Schmierung verwonde man Markenole wia / Motor Mobiloil TT / Mischungsvethaltnis 1:20 / Getriebe. Mobilube C140"machinery, timber cutting

Leigh Conkie is a well known Eltham artist who creates a wide variety of subjects in wood modelled by chainsaw at his home in Main Road. Location unknownfay bridge collection, chainsaw sculpture, leigh conkie, 2013-07-21, sculpture

"Pioneer" chainsaw with green housing. Pull start, no chain. Compliance plate on back (see Below) second plate on top.Compliance plate on back "Pioneer Saws / Model / 450 / Serial No. A10778 / Division of Outboard Marine Australia Pty. Ltd. / Bankstown NSW". Cast in relief on side "Pioneer & Pine Trees".machinery, wood cutting

This chainsaw was one of the earliest models sold in Australia. It was manufactured by the Lombard company which was established in 1894 when Nathaniel Lombard developed the first practical water wheel governor in Roxbury, Massachusetts, USA. In 1904, the company moved to Ashland, Massachusetts. During the first World War, Lombard Governor produced hydraulic lathes for the manufacture of artillery shells At the conclusion of the war, Lombard expanded into the areas of chain saws and plastic molding injection machines. This model, the L-30 was only produced for 2 years from 1962 - 1964, primarily due to safety concerns and the fact that it did not have any way to sharpen or tighten the chain. This chainsaw was sold by Mann of Wodonga and donated to the Wodonga and District Historical society by David Mann, owner and manager of Mann Wodonga.This item is significant as it was produced for a limited time. It was also sold by a prominent Wodonga business.A single operator chain saw from Lombard, Ashland, Massachusetts, USA. The chainsaw was relatively lightweight but had no safety features such as a chain brake. It was made primarily of sand cast magnesium. The main cylinder was constructed of aluminium with a cast iron sleeve. It had a manual oil pump, the crankshaft operated on ball bearings and it had a maximum rpm of 4,500. See the Model profile in the accompanying Media item for details.On side of fuel tank: "ONE HALF PINT/SAE-30 OIL/ FOR EACH/ GALLON GASOLINE/ MIX WELL IN SEPARATE CONTAINER/BEFORE FILLING" On opposite side: "STARTING INSTRUCTIONS 1: FILL FUEL TANK WITH PROPER FUEL MIXTURE ( AS NOTED ON TANK) 2. FILL OIL RESERVOIR WITH #30 MOTOR OIL 3. CLOSE CHOKE, MOVE LEVER BACK TOWARDS AIR FILTER 4. HOLD THROTTLE WIDE OPEN 5. PULL STARTER HANDLE SLOWLY UNTIL STARTER ENGAGES, THEN GIVE IT A SHARP YANK 6. AS ENGINE WARMS UP, EASE CHOKE LEVER TO OPEN POSITION"hand tools, vintage chainsaws, david mann, mann wodonga

Continuous cutting chain was patented in 1905 by Samuel Bens of San Francisco, while the first portable chainsaw was developed and patented in 1918 by Canadian millwright James Shand. But the main advancements of modern petrol chainsaws occurred in Europe in the 1920s and 30s where Andreas Stihl is often hailed as the "father of the chainsaw" After the second world war lighter materials, metal alloys and improved engine designs revolutionised the logging and timber industry. This Wright Reciprocating Saw was made in Sheboygan, Wisconsin, between 1960 and 1962. Its a Rare GS-5020A model. It has a 7.06 cu. in. (115.7 cc), two-stroke motor, which weighed 25 lbs. (11.3 kg) complete. The blade doesn't stop reciprocating when the saw is running because it's attached directly to the crankshaft. There is no clutch system.Reciprocating Saw.forests commission victoria (fcv), forest harvesting, hand tools

Burnley College training of students and maintenance of Burnley Campus gardens.Petrol driven chainsaw, coloured with pale yellow enamel paint. 'Canadien 210' Model 2-10 No. 21107. Serial Number (obscured), Power Machinery Ltd, Vancouver, British Colombia, Canadahorticulture, arboriculture, sawing timber, tree maintenance, wood saw, burnley college of horticulture

Model of a 2-stroke motor, clutch and spark plug cable with one side cut away to show the inside. Used for teaching arboriculture at least until the 1990'sMcCullocharboriculture, teaching, 2-stroke motor, model, clutch, spark plug cable, chainsaw, mcculloch chainsaw