Cooper Handbook Modern Sheep Dipping Soft Cover 47 Pages. 1956 - 1969. Issued by William Cooper & Nephews (Aust) Pty Ltd. Printed in Australia by William Brooks & Co. Limited 723 Elizabeth Street Waterloo.history, agriculture, book modern sheep dipping

This ledger was used by the Shire of Orbost from 1911 - 1914. It was used to record fees paid for Dairy Registration, Dog Registration and Sheep dipping. At that time dairy farmers were required to register all milking cows. Dogs, too, were to be registered and there were strict laws on sheep dipping. Every sheep-owner was to dip all his sheep immediately after shearing and directly from the shearing-board in every year and also at the time of dipping his sheep dip all his lambs. In case the sheep couldn't be conveniently dipped directly from the shearing board they were to be placed and kept in a securely fenced paddock to be dipped within sixty days after shearing. Sheep-owner who neglected or failed to comply with any of these directives were liable to a penalty of not less than One pound nor more than Twenty pounds. The shire covered an area of 9,347 square kilometres and existed from 1892 until 1994 when it became part of the East Gippsland Shire Council. Orbost was at first included in the Bairnsdale Shire from 1882 and was later part of the Tambo Shire. Because of travelling distances the Croajingalong Shire was created in 1892 (name changed to Orbost Shire 17.2.1893 with James Cameron as the first Shire President. In 1994 it amalgamated to become part of East Gippsland Shire Council. The item was donated to Orbost & District Historical society from P.R.O.V. as a Place of Deposit (POD) item for safe keeping by a local history group or museum. The shire covered an area of 9,347 square kilometres and existed from 1892 until 1994 when it became part of the East Gippsland Shire Council. This item is a record of local council accounting. The Shire of Orbost no longer exists as it was absorbed by the East Gippsland Shire Council.A dark blue, leatherette covered ledger cash book with tan spine, stitched marbled end covers. Records are handwritten in blue and red ink and blue pencil. It contains records of Dairy Registration fees, Dog Registration fees and Sheep Dipping fees.Inside the front cover is a list of contents.ledger orbost-shire-council sheep-dipping dairy-registration accounts

This is a photograph of one of the many stone ruins which can be seen in the Sunbury area and surrounding districts. These ruins are found in varying degrees of structural damage caused by erosion, vegetation growth and vandalism. The bluestone structure was a sheep dip on the 'Karoora Park' property near Jacksons Creek.A coloured photograph of the stone remains of a sheep dip constructed from basalt rock. The ground at the entrance slopes down into a narrow walled channel. The surrounding paddocks are covered with tussocks of grass and there are bare hills in the background. The grass is brown.stone structures, sheep dips, basalt rock, 'karoora park', george evans collection

Black and white photograph of old timber yards and stone sheep dip.lewers, hoyles creek, mannibadar, farm

Hypodermic syringe gun in box donated by Tom Crocker (former Operations Manager, National Wool Museum), used on father's property in Violet Town.Metal hypodermic syringe gun.The Repeater Hypodermic syringe Wilcox Mofflin Limitedsheep dipping, crocker, mr tom - national wool museum

Receipt issued to Mrs. W. Grigg 20/10/1941.Text: " Phones - Linton Nos. 3 and 8. / LINTON / J. & F. O'BEIRNE / WOOL AND SKIN MERCHANTS. / Wool-scouring and Fellmongery Works at Breakwater, Geelong. / Distributing Agents for Thomas' Sheep Dip, Gold SeEal Motor Lubricating Oils. / Manufacturers of Neatsfoot Oil. "mrs. w. grigg, j. & f. o'beirne, linton

THIS TOOL CAME FROM WALTER COOK'S FARM AND WAS USED WHEN BLASTING ROCK DURING CONSTRUCTION OF SHEEP DIP. IT WAS THOUGHT TO BE USED MUCH EARLIER IN THE HISTORY OF THE FARM TO BLAST THE WELL WHICH IS THE MAIN WATER SUPPLY FOR STOCKTOOL USED TO CLEAN OUT HOLE FOR DYNAMITE WHEN BLASTING ROCKlocal history, trades, tools, cook family

Handwritten notes about Liddel's Pyrite Works which first worked about 100 years as the Derwent Gully Pyrites Works. Notes give description of how Liddel's Pyrite extracted the gold and collected arsenic which was sold to manufacturers as sheep-dip, weed poison, etc. Also mentioned is Leggo's Burner which started operations, 1906 and closed about 1949 or 1950.document, gold, liddel's pyrites works, liddel's pyrites works & leggo's burner, pyrites

Second in a set of two books containing newspaper cuttings relating to the wool industry, which include topics such as arbitration proceedings, blowfly strike, sheep breeding, competitions, wages, workers unions, equine education, fencing, manpower, land valuing, shearing, pastoral conditions, rainfall, sheep dip, tanning, meetings and wool markets. Bound maroon covered book containing newspaper articles. Spine [printed]: NEWSPAPER CUTTINGS – BOOK II.wool, wool industry, wages, cost of living, shearing, legal cases, exports, horses, tax, union, women at work, newspaper articles

Note from Deb to Bernadette mentioning the new system account numbers as the old ones are not valid any more. Accounts include Market Dues, Agents Fees, Truck Wash, Branding Fees, Sheep Dip and Sundries including Telephone Accounts. Sticky taped to the back are some addresses. They include Clarrie Scott, Oakey Holdings, Steven Lang, Brian Braden, Smorgons Consolidated Inc, Arnbrook, D & P Meats and Safeway.bendigo, council, cattle markets, bendigo saleyards collection - new account numbers, clarrie scott, oakey holdings, steven lang, brian braden, smorgons consolidated inc, arnbrook, d & p meats, safeway

Places of Historic Interest in and around St Albans|The ABC Radio mast and transmitter station|The Blue stone Culvert bridge|Sydenham railway station|Robertsons Upper Keilor Homestead|A Sheep Dip|The Overnewton Venue|The Overnewton Gatehouse|Anderson Cottage|the Hume and Hovell Cairn| Keighlo|St Albans Railway Reserve Grasslands|The Anderson Farm House|The St George Fee Serbian Orthodox Church|The Agnes Stevens farmhouse|The Stensons Family Farm|The Errington Reserve Gates|The St Albans Community Youth Centre|St Albans Town Plan|St Albans Uniting Churchst. albans, harrsion

Born in England in 1832, Albert Bush was attracted to Australia by the lectures of Dr Laing. In 1852 he travelled to Queensland and later to Sydney before coming to Bendigo. His initial mining efforts were not successful so he gained employment as a clerk in a grocery store. In 1857 he opened his own grocery shop in partnership with Mr Ferris. He bought out Ferris in 1859. In 1859 he married Jane Dalton (1836-1919). Following his death the business was continued by his son.Albert Bush's Stores Invoice. Cream paper with black print, hole in the centre. Bush's Moulamein & Wakool. Dated at Bendigo August 5th 1929. Mr S. A. Bush. Both of Albert Bush's Stores General Providers. Grocers, Bakers and Pastry cooks, Drapery, Hardware Timber, Woolpacks and Cornsacks. Insurances, Mitchell Farm Machinery, Mt Lyell Manures Sheep Dips, Building (under our own supervision). Invoice for 1 truck Box Blocks. Freight seven tons. Cartage Buckell & Jeffrey. Truck 1515. Receipt attached no. 172 dated August 19th 1929 with orange Stamp Duty Stamp for 2d. Mr S.A. Bush By Cash Cheque £11:6:1 Albert Bush's Stores. Box 625business, retail, general, albert bush's stores. s.a. bush

Augustus Bostock was the 9th child of Robert & Rachael Bostock of Vaucluse Epping Forest, Van Diemen’s Land. He was only 4 years old when his mother died. He was inspired by his father to seek his fortune in the Western District of Victoria. He arrived around 1850. He married Margaret Aitkin in July 1865. Augustus owned several properties in the district and leased others. He sat on the court of Warrnambool, Mortlake or Hexham as required. He resided at Marramook in Hawkesdale and later moved to Vaucluse in Hopetoun Road Warrnambool, where he died in 1920 at the age of 87. He was involved in many aspects of life in the Western District, racing, cricket, and social activities to name a few. This is one of a number of personal letters exchanged between Augustus Bostock and E H Macartney. Generally the topics discussed relate to sheep and farming practices, in this case the construction of a sheep dip and the sale of Lincoln sheep and expenses.This is one of a number of documents which relate to the Bostock family who were one of the most important pioneering families of the Western District. They owned and leased various properties around Warrnambool and were involved in many aspects of social and business life. As a letter , which discusses issues of the day, this item has social and historical significance.Cream lined paper folded in two. Written in black ink over three and a half pages with hand drawn diagram at the end of the letter.Dated September 27th 1900. Marramook. Addressed to E H Macartney Delatite Mansfield.augustus bostock, e h macartney, warrnambool, lincoln sheep

Augustus Bostock was the 9th child of Robert & Rachael Bostock of Vaucluse Epping Forest, Van Diemen’s Land. He was only 4 years old when his mother died. He was inspired by his father to seek his fortune in the Western District of Victoria. He arrived around 1850. He married Margaret Aitkin in July 1865. Augustus owned several properties in the district and leased others. He sat on the court of Warrnambool, Mortlake or Hexham as required. He resided at Marramook in Hawkesdale and later moved to Vaucluse in Hopetoun Road Warrnambool, where he died in 1920 at the age of 87. He was involved in many aspects of life in the Western District, racing, cricket, and social activities to name a few. This is one of a number of letters from E H Macartney of Delatite station to Augustus Bostock, with this one relating weather, details, sheep and the building of a sheep dip. This is one of a number of documents which relate to the Bostock family who were one of the most important pioneering families of the Western District. They owned and leased various properties around Warrnambool and were involved in many aspects of social and business life. This letter relates farming and social details at the timeCream lined paper with large margin on left side. Written in black ink.E H Macartney, Delatite Mansfield , 25th Sept 1900warrnambool, bostock, augustus bostock,

Blue duplicate Purchase Requisition Book dated 21/1/92 to 29/7/92.Cover has crocodile pattern and blue cloth tape on the spine. Tape on inside front cover. Items in the book include electrical work/repairs, stationary and office supplies and equipment, branding fluid, hardware, welding, dog food, screenings and spreading and checking scale. Blue duplicate pages and white originals. Last pages have This book is cancelled S? written across it. Back cover is missing. Two loose pages in the book. One is a duplicate For All Bull Cattle Colour, dated 3/2/92 for silver and yellow branding fluid. The other is a V/Line Freight Consignment Note dated 5/2/92. Purchase Requisition book with a red and cream patterned book with a red tape spine and blue pages. Saleyards is written in balck texta on the front of the red spine. Book is dated from 24/8/90 to 8/1/92. Requisitions signed by J M Crimmins and J Richmond. Requisitions were for electrical work, plumbing supplies, office materials, branding fluid, dog food, sheep dip, weed killer, repairs to yards, tools, printing, hay, and repairs to truck wash.bendigo, council, cattle markets, bendigo saleyards collection - city of bendigo purchase requisition, hume & iser, brb electrical, boltons bros, d walker pty otd, all bull albury, bearing & industrial supplies, midland irrigation, watson & crane, ray t thompson, golden triangle communications, blue line office supplies, allweld construction, toledo scales, david bolton, dalgety farmers, j m crimmins, rodger wrigley, dookie college, b p bury, ron dixon, beaurepaires tyers, steven hyde, bendigo scale co, d g walker pty ltd, reece, midland ir, bendigo engineering

Cooper S.E. Ball Bearing Grinder made and guaranteed by Sunbeam Corporation Limited. Grinders like this example have been made the same since the early 1900s, with this grinder thought to have been produced in the 1960s. It is belt driven, with the other end of the belt being attached to an engine; the same engine that would have powered the overhead shearing equipment in shearing sheds. It was common for shearing teams to bring their own equipment, especially pre-1960 as most shearing sheds were not connected to power, and shearers preferred to work with their own equipment. The engines that powered the shears and grinder were typically fuelled with kerosene or petrol. The large circular disks are attached to the bolt that protrudes from the grinder and fastened tightly with a nut. An example of seeing a similar grinder in action can be found on the following link - https://www.youtube.com/watch?v=O7eimI_Gm9o. Inventor Frederick Wolseley made the world's first commercially successful power-shearing system in Australia in 1888. US company Cooper, which had been founded in 1843 as a maker of sheep dip, began selling Wolseley equipment in the USA in 1895. The Chicago Flexible Shaft Company successfully entered the power-shearing market a few years later and entered a joint venture with Cooper. It set up a branch in Sydney and sold shearing sets, and engines to power them, into the Australian market. In 1921 the US parent company, realising it needed to make products whose sales were not as seasonal as those of shearing equipment, made its first household appliances and branded them Sunbeam. In 1933, changes in exchange rates and taxes led the company to manufacture engines and shearing equipment in Australia via subsidiary Cooper Engineering, which changed its name to Sunbeam in 1946. Although most Australians know of this company as a major manufacturer of household appliances, its rural division flourished and retained the Sunbeam name for shearing equipment even after it was taken over by New Zealand company Tru-Test in 2001. The grinder is formed from a central arch shaped block of green painted metal. Much of this paint has been lost to age, leaving the grinder in a ‘farm used’ condition with much surface oxidation present. On the front of the arch is a specification plate, reading “Cooper S.E. ball bearing grinder. Made and guaranteed by Sunbeam”. At the foot of the arch, three bolt holes are found for securing the grinder to the base of a solid wooden surface. Two of the bolt holes are found on the front of the grinder, with another found on the rear. From the central arch, a bolt protrudes to the right of the grinder. This large bolt is for securing a grinding plate to the grinder. Above the central arch is a pendulum which holds the comb / cutter that is being sharpened. From the pendulum, a large arm extends down (not pictured) to meet and strike the plate spinning at a rapid speed. On the left-hand side of the central arch of the grinder, a wheel is found which a belt is attached to for power. This belt is then attached to a separate engine, spinning the wheel and hence powering the grinder. The wheel is partially covered with a section of protective bent tube, designed to provide protection from the rapidly spinning wheel. Below this wheel is the belt shifter. It is designed to move the protective bent tube from one side of the grinder to the other, to accommodate the grinder in the setup of different shearing sheds. The two separate grinding plates are identical. They have a slight slope for sharpening the comb and cutters in the correct method, with a slight bias towards the base, or “tooth”, of the equipment. The disks have a large central bolt for attaching to the grinder. They have tags on the horizontal axis of the grinding plates, for securing the plates in transportation, and to help with initial alignment when setting up the grinder. The reverse of these grinding plates has the same green painted metal finish found on the grinder. This paint is also in a ‘farm used’ condition, with surface oxidation present. The grinder would be provided from the factory with a comb holder, shifter for securing the grinding plates, emery cloth and emery glue. The emery cloth is what does the actual grinding and is applied to the grinding disks, replacing once well worn. These items can be seen in the final images in the multimedia section, showcasing advertising for this grinder. Plate. Inscribed. “Cooper / S.E. BALL BEARING GRINDER / MADE AND GUARANTEED BY / Sunbeam / CORPORATION LIMITED / SYDNEY MELBOURNE / ADELAIDE BRISBANE ”sheep shearing, shearing equipment, sunbeam, grinder

Dry stone construction as a technique is used for much more than paddock walls. Across the volcanic plains of western Victoriaare marvelous sheep dips, stock loading ramps, huts, dams, retaining walls, and the rich and largely undiscovered heritage of indigenous dry stone structures. Dry stone walls indicate many aspects of our rural environment; the geological beginnings of the way the landscape was created, the patterns of early settlement by pastoralists and squatters, the types of stock that grazed the land and the methods of cattle and sheep management, of the efforts to thwart the spread of rabbits .... "For the casual but interested observer dry stone walls are good to look at, to photograph, to get up alongside and see the way they are constructed, to appreciate the varying shapes and sizes of stones and learn of the techniques of keeping often quite rounded stones in place. Apart from walls and other dry stone structures on grazing land we can also see dry stone techniques used in other places and in other phases of our history. Indigenous Australians have built, and continue to build, structures for shelter or hunting or trapping eels and fish in rivers and estuaries around the country. At spots around our coast line there is evidence of simple stone structures built by early maritime explorers. Prospectors in early mining encampments used dry stone construction to build retaining walls or the low walls of rudimentary shelters. If the future of dry stone walls in the Australian landscape is to be assured. wall owners and local governments have to accept and embrace their custodial role in assuring the preservation and celebration of walls. This is not an easy task, but, along with putting the necessary statutory mechanisms to ensure their retention, it is a task that must be pursued. The Dry Stone Walls Association of Australia has as its primary goal the increase in awareness of wall owners and local governments of the importance of dry stone walls. It also seeks to increase the level of training of skilled and semi skilled wallers, and the gaining of rudimentary skills by farmers so that they can maintain their own walls". Melton Star Weekly article about the Stone Wallslandscapes of significance

With more and more woolsheds being connected to power lines, the need for electric shearing gear markedly increased from the 1960s onwards. The greater economy made electric gear an attractive proposition to many graziers. Requiring only an electric shearing motor, for small and medium scale operations, electric shearing motors were a more economical way of shearing a wool clip. The other option for graziers was Overhead shearing gear, which also required an Engine to provide shared power to a row of shearing stations. Still working, this Sunbeam Electric Shearing Motor – Heavy Duty Model, features a slow speed motor totally enclosed for protection against dust and insects. The full bearing down tube is easily removed and stored to be out of the way when not in use (not pictured). Providing 0.5 hp, which is twice the power ever needed for shearing sheep, this buffer allows for fluctuations in voltages that can occur in rural districts. Inventor Frederick Wolseley made the world's first commercially successful power-shearing system in Australia in 1888. US company Cooper, which had been founded in 1843 as a maker of sheep dip, began selling Wolseley equipment in the USA in 1895. The Chicago Flexible Shaft Company successfully entered the power-shearing market a few years later and entered into a joint venture with Cooper. It set up a branch in Sydney and sold shearing sets, and engines to power them, into the Australian market. In 1921 the US parent company, realising it needed to make products whose sales were not as seasonal as those of shearing equipment, made its first household appliances and branded them Sunbeam. In 1933, changes in exchange rates and taxes led the company to manufacture engines and shearing equipment in Australia via subsidiary Cooper Engineering, which changed its name to Sunbeam in 1946. Although most Australians know of this company as a major manufacturer of household appliances, its rural division flourished and retained the Sunbeam name for shearing equipment even after it was taken over by New Zealand company Tru-Test in 2001. This 0.5 horsepower vertical brushed motor air-cooled engine was designed to drive a single shearing plant. From the central cylinder which features a yellow “Sunbeam” sticker, a grey 240v power lead can be found on the left-hand side. A blue capacitor is located next to this power lead. Below, two legs extend and meet to form a foot which is fastened to a wall. On the right-hand side of the engine, a specification plate is located on the central cylinder. A yellow directional arrow sticker is located on the rotating section of the engine below the specification plate (location for photography, this section is designed to rotate and hence this sticker is not fixed in this location). At the rear of the cylinder, a plastic cap with small air cut outs protects the air-cooled engine from contaminants. At the front of the engine, the location for securing the bearing down tube is located. On the right-hand side of the lock for the bearing down tube is the handle, to which a string is often attached for switching the motor on and off by a shearer bent at the waist (not pictured). Sticker. Gold writing. Front of shearing motor “Sunbeam” Plate. Inscribed. Side of shearing motor. “Sunbeam / SHEARING MOTOR / MADE IN AUSTRALIA / 0.5 H.P. / 220/240 V / 1 PHASE A.C. / 4.0 AMPS / 50 C/S. / CONT. RTG. / 1425 R.P.M. / CLASS A INSUL / NO. J244560 / TYPE: NSB5C2/49." sheep sheering, shearing equipment, sunbeam, electric shearing motor

Was folded up and pasted into the minutes of the Borough Legislative Committee opposite June/July, 1865. Joan WINTER, City of Port Phillip Collections Manager, paid for conservators to remove and restore it, then framed it for exhibition in 'Dreedging, Draining and Dipping'1995/96. Following end of exhibition it was returned, in frame.Large typeset framed proclamation, "Rules and Regulations for the management of the Sandridge Borough Common" Dated 13 July 1865. Refers to cattle, cows, calves, horses, sheep, goets, pigs and the herdsman rulesbuilt environment - civic, livestock, andrew plummer, edward clark, town clerks

This was used to brabd sheeep to identify the owner. The brand was dipped in branding fluid then placed on the sheep's back following shearing.Crude wooden brand made of 6 pieces of pine wood box timber to form the letter Eshearing, branding, wool industry

John Griffin’s wool classing exercise books from 1941-1943 when he was a student at the Gordon Institute in Geelong. John and his father John Henry Griffin owned a farm in Dunkeld and bred fine merino wool. One year they topped the wool sales figures for the area, in the late 1940s. There are four books in total. One book is on the topic of Veterinary Science and is from 1941. It contains information on topics such as birth and early lamb life, bone structure and other internal organisms of a sheep, such as the heart. Another book is on Wool Classing with topics such as wool scouring, dipping, shearing and micron counts. The third book is on general shearing shed knowledge. This includes a diagram for rolling a fleece, correct method for stamping a wool bale and branding abbreviations. The final book is on the History the Merino Sheep. It is a long form essay answer booklet. The Gordon institute and wool are synonymous with one another, the first class in wool sorting was offered at the Gordon in 1891. With much of the wool clip sent directly to England at this time, The Gordon's focus soon shifted to wool classing and marketing. By the 1930s, The Gordon's wool school was renowned as the state's wool industry training centre. Early specialist short courses were offered around Victoria to assist wool growers in preparing their clip for market, with modules on sheep breeding and pasture development included in the programs. Anne Griffin’s, John’s daughter, donated the exercise books to the National Wool Museum in 2021. Book 1 is predominately blue circular cover with cream background. Middle of book has pink highlighter mark. Reverse of book has an Arithmetical Table and a Multiplication Table in a blue ink on cream paper. It also has four black ink markings Book 2 is predominately blue circular cover with cream background. Book has red tape across the spine. Reverse of book has an Arithmetical Table and a Multiplication Table in a blue ink on cream paper. Book 3 is predominately blue plaid cover with cream background. Middle of book has pink highlighter handwriting which has been crossed with the same colour, leaving the text unreadable. Reverse of book has an Arithmetical Table and a Multiplication Table in a blue ink on cream paper. Book 4 is predominately blue diagonal striped book with cream background. Middle of book has small picture of Australia. Reverse of book has an Arithmetical Table and a Multiplication Table in a blue ink on cream paper. Book 1. Front cover: “All Schools” / EXERCISE BOOK / NAME Jack Griffin Grade Gordon Institute School of Technology(?) / Approved by the / Education Department Back cover. Reverse. ARTHMETICAL TABLES / (Numerous, see media) Book 2. Front cover: 2nd & 3rd / “All Schools” / EXERCISE BOOK / Name Jack Griffin / Grade 2 / School the Gordon / Approved by the / Education Department Back cover. Reverse. ARTHMETICAL TABLES / (Numerous, see media) Book 3. Front cover: Embassy / EXERCUSE BOOK / Name John Griffin / Grade 1 / School (?) / APPROVED BY THE EDUCATION DEPARTMENT / Back cover. Reverse. ARTHMETICAL TABLES / (Numerous, see media) Book 4. Front cover: EXERCISE / APPROVED BY EDUCATION DEPT. / BOOK / NAME Jack Griffin / GRADE 3 / SCHOOL Gordon Back cover. Reverse. ARTHMETICAL TABLES / (Numerous, see media) gordon institute geelong, wool classing, 1940s sheep farming, note book, study, student

Four page booklet featuring printed text, with a red banner and logo of a sheep on the front cover. front: [printed] COOPER / RELEASE OF / INFORMATION / THE EXHAUSTION OR STRIPPING OF DIPS / by G. C. Brander, B.Sc., M.R.C.V.S.products, agriculture, animal breeding, animal husbandry, william cooper and nephews (australia) pty limited, vaccination

Four page booklet featuring printed text, with a yellow banner and logos of a sheep and a cow on the front cover. front: [printed] COOPER’S / SALES & SERVICE / Bulletin / THE USE OF ARSENIC & DIELDRIN DIPS / IN COMBINATIONproducts, agriculture, animal breeding, animal husbandry, william cooper and nephews (australia) pty limited, vaccination

Double sided leaflet with cream, black and white printed text and graphics. Front shows an image of sheep standing under a liquid spray. front: [printed] EASY TO USE / NO PREMIXING / COOPER’S LIQUID ARSENICAL DIP products, agriculture, animal breeding, animal husbandry, vaccination, health