Sad-irons or "solid" irons were made by blacksmiths and used to smooth out material by pressing the hot iron over it. A piece of sheet -iron was placed over the kitchen fire and the irons placed on it could be heated whilst remaining clean of ash.. The women used 2 irons - one heating while the other was used. Thick cloth or gloves protected their hands from the hot irons. The handle was removed from the cool iron and re- attached to remove the hot iron from the fire. The cool iron was replaced on the fire or stove to heat again. Mrs Florence Potts invented in 1871 a detachable handle made from walnut wood with a metal latch to release the handle. These wooden handles prevented burned hands and were sold to grateful women all over the world. These irons were cleaned with steel wool to prevent them marking the material. If the iron was too hot the material would scorch. Most homes set aside one day for ironing and some large households had an ironing room with a special stove designed to heat irons. However, most women had to work with a heavy, hot iron close to the fireplace even in summer.Mrs Florence Potts invented this type of detachable walnut wood handle with a meta release latch for sad irons in 1871 and it sold widely throughout the world to grateful women including those in Moorabbin Shire. The family of Ms May Curtis were early settlers in Moorabbin ShireA) A sad iron, made of cast iron , has a special handle invented in 1871 by Mrs Florence Potts of Iowa, USA. B) The detachable handle made of walnut wood to prevent burned hands, was attached to the iron by a metal latch.A) UNITED/ N0 / 50 / AUSTRALIApotts florence, iowa usa, melbourne, moorabbin, sad irons, kitchen equipmentn fireplaces, walnut wood, sewing, laundry, table ware, linen, pioneers, early settlers, washing days, craftwork

Butz-Choquin is a French pipe maker founded in 1858 by tobacconist Jean-baptiste Choquin and Gustave Butz.The company was established in Metz; it remained there until 1951, when it was purchased by the Berrod-Regad company. It was then relocated to Saint-Claude, Jura. The company was acquired by Denis Blanc in 2006. Butz-Choquin's first pipe, the Choquin pipe, was a curved pipe with a flat-bottomed hearth, albatross bone, and silver rings.A 'Butz-Choqin' tobacco pipe with walnut wood stack-like bowl, horn stem and silver perforated lid. The octagonal base unscrews. Silver rings around the lid and join from bowl to stem BUTZ-CHOQIN / Made in France / N0.3 / VERCOURS / BC (engraved) smoking pipes, tobacco, butz-choqin company france, walnut wood, albatross bone, market gardeners, pioneers, early settlers, moorabbin, brighjton, bentleigh

The two-section corner cabinet is in a Victorian style, made of burr walnut. There is a cornice above two astral glazes glass middle-opening upper doors with a wood-panelled bottom cabinet and moulded plinth base. The cabinet has brass hinging and locks.furniture, cabinet, walnut, wood, victorian-style, victorian-era

The tree branch from which this wooden item was sculpted was from a walnut tree on the property of Dominico Lorensini, on the corner of Yendon No. 2 and Geelong Roads, BuninyongThe walnut tree whose timber was sculpted, was from the historic property of an early Buninyong family, the Lorensini family.Piece of a branch of a walnut tree, sculpted into a timber item with a central narrow stem.walnut, timber, wood, buninyong, lorensini family

Bluthner piano dated 1889 (patent no. 32310). PWD engraved imprint to wood. "The Bluthner grand piano came second-hand to the Chalet in 1920 when it was obtained by lessee, Hilda Samsing. This high quality German piano, which stands out as an item of individual significance, is now one of the oldest furnishings in the Chalet. When it was acquired in 1920, the Chalet already had a Beale brand upright piano which had been at the Chalet from the earliest days." (Pg. 77 Historica. 2011) 'A photograph taken of the Music Room (also known as the Drawing Room) between 1920 and 1924, when Hilda Samsing was lessee is one of the earliest known photographs of the Chalet's lounge areas. Published in the undated promotional booklet, Victoria's Wonderland Mount Buffalo, it shows 'A corner of the music room'... On the right, is the Chalet's second piano, which was purchased second-hand in 1920 from Gardner & Lang in Swanston Street, Melbourne. This impressive grand piano of walnut wood still stands in the Chalets Music Room. It was made in the world-famous factory of Julius Bluthner, in Leipzig, Germany, which has made Bluthner pianos since 1853 for numerous royals, composers, conductors, artists, authors and performers including Brahms, Mahler, Bartok, Debussy, Wagner, Strauss, Tchaikovsky and Rachmaninoff. The present stool is not part of the ensemble." ( Pg. 42. Historica )Listed in Draft Inventory of Significant Collection Items. Appendix A.1. Furnishings, Lounges and Hallways (Pg 163. Historica"Bluthner" grand piano made from walnut wood with accomanying wooden stool.(not matching). Piano features three large turned and carved legs on brass castors. Pedals on piano are solid brass, surrounded by carved and turned wooden pedal stand. Stool seat slants towards piano and two plain stretchers support four curved legs. Has 'PWD' stamped on it. PWD engraved imprint to wood.

This writing desk was used by the Warrnambool Bank of Australasia personnel and the date associated with it (through unproven Historical Society records) is 1859. The Bank of Australasia was established in Sydney in 1835. The Warrnambool branch of the Bank of Australasia was established in 1854 in a stone cottage in Merri Street leased for two years. The bank was next located in a leased building in Timor Street with new purpose-built premises at the corner of Timor and Kepler Streets opening in 1860. In 1951 the Bank of Australasia merged with the Union Bank to form the A.N.Z. Bank Limited. In 1970 the E. S. & A. Bank and the London Bank of Australia merged with the A.N.Z. Bank forming the A.N.Z. Banking Group Limited with the business transferring to Liebig Street. The old Bank of Australasia building was purchased by the Warrnambool City Council and later sold to a private buyer. It is now a nightclub. The writing desk may have been used in both the Timor Street leased building and the bank building at the corner of Kepler and Timor Streets. William Palmer was the Bank Manager when the desk would have been first used. This is a most significant item as it comes from the Warrnambool Bank of Australasia, the first bank to be established in Warrnambool and a major banking business in Warrnambool for nearly 100 years. The desk was handed over to the Warrnambool and District Historical Society by Clarrie Kempton, the A.N.Z. Bank Manager in Warrnambool from 1964 to 1971.This is a wooden writing desk, possibly made of walnut wood. The base is rectangular with a drawer with a brass handle at the base. From the base the desk slopes up to a triangular shape with a slightly curved top. The middle of the desk has a front opening with two doors with four brass hinges with a brass lock. There are six bolts, one with a slot missing. Inside the doors are inset 10 wooden slots of different sizes to hold papers, letters, ink, dockets etc. Also inside the doors, behind a transparent material, are spaces for the day, date and month. These numbers and letters were once able to be changed according to the date. The writing desk is in good condition but a little stained. ‘Tuesday’ ‘8’ ‘November’ bank of australasia, history of warrnambool, history of warrnambool

Flat irons were also called sad irons or smoothing irons. Metal handles had to be gripped in a pad or thick rag. Some irons had cool wooden handles and in 1870 a detachable handle was patented in the US. The detachable insulated handle was designed to be always cool for ironing. The handle was detachable, so that several irons could be on the stove at one time and the handle swapped between several bodies. This handle appears to belong to a Mrs Potts' sad iron - Reg. No. 1885. This item is an example of an invention that was universally adopted because it meant that users could keep several irons on the stove at one time and the handle swapped when needed. The original Mrs Potts irons had handles made of wood (walnut) and this enabled the user to us the iron without sustaining burns. The item reminds us of the difficult circumstances experienced in their daily routines by the early families in Orbost A wooden handle which has been painted green. The base is made of cast aluminium and is attached to the handle by two screws ( not original). In the base is a hinged piece for attaching to the iron, held to the base plate by a spring and operated by a wooden knob for quick release. A hook holds the handle to the iron.On the base is an indecipherable number.handle sad-iron flat-iron mrs-potts domestic laundry

Mrs. Potts invented the Potts Removable Handle Iron. Her invention of the Cold Handle Sad Iron changed the clothing iron industry. The detachable insulated handle was designed to be always cool for ironing. The handle was detachable, so that several irons could be on the stove at one time and the handle swapped between several bodies.This item is an example of an invention that was universally adopted because it meant that users could keep several irons on the stove at one time and the handle swapped when needed. The original Mrs Potts irons had handles made of wood (walnut) and this enabled the user to us the iron without sustaining burns.A Mrs Potts Sad Iron.It is a double point design with detachable handle. The detachable insulated handle was designed to be always cool for ironing. The handle was detachable, so that several irons could be on the stove at one time and the handle swapped between several bodies. There is no handle with this iron. MRS POTTS. Rest is indecipherable.domestic-appliance mrs-potts sad-iron flat-iron laundry

A gentleman's chair, gent's chair or grandfather chair is a term usually applied in Australia to a deep upholstered Victorian easy chair, often button-backed and with upholstered arms. The chair generally stood on short cabriole legs and had a 'spoon' or a wide balloon back. The 'show wood', that is, the polished frame, was usually mahogany or walnut, although many examples in Australian red cedar have survived. There are Australian versions of the gentleman's chair, lady's chair and matching settees, usually made from cedar, and occasionally from blackwood. As cedar is a softer timber than walnut, mahogany and rosewood, from which the English versions were made, the carving is usually not as crisp as in the imported version. However, the Australian blackwood gentleman's chair is often difficult to distinguish from a good-quality English walnut example. The Edwardian form of the gentleman's chair is much squarer in outline, with short turned legs and the arms are often supported by spindles. There was sometimes a row of spindles, like a gallery, beneath the top rail. The chairs were frequently upholstered in leather.An item probably made in Australia during the latter half of the Victorian era and is significant as it was made in Australia at a time when furniture and many other household items were imported from either America or England.Armchair: gentleman's armchair of Cedar wood with brown leather upholstery, tacked and buttoned in a crocodile-skin-like effect. The wood is scalloped and carved with a Prince of Wales Feather on the back. The arms are scrolled and carved with an Acanthus leaf design, finished on tulip turned legs. All four legs have brass and porcelain castors. circa 1870, Australian-made. flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, furniture, chair, armchair, gentleman's chair, lady's chair, leather upholstery, buttoned upholstery, living room furniture, lounge room furniture, formal furniture, domestic

Photographer notations on slide: "Unloading Timber at Wharves 1933 Age B5" Published: Age (Melbourne, Vic.: 1854- ), Tuesday 15 August 1933 MAHOGANY FROM MANILA. (1933, August 15). The Age (Melbourne, Vic. : 1854 - 1954), p. 11. Retrieved January 16, 2026, from http://nla.gov.au/nla.news-article204377024 Published title: MAHOGANY FROM MANILA Published Caption: Age Tue 15 Aug 1933 Caption: Unloading Mahogany Logs brought from Manila, Philippine Islands, by the steamer Taiping, which berthed yesterday at Victoria Dock. The vessel discharged twenty logs, each weighing three tons, the first shipment of this type of timber landed in Melbourne. Research by Project Volunteer, Louise McKenzie: This photograph in many ways epitomises Melbourne in the 1930s. It is a time of enormous growth, development and change. But before delving into that, the photo itself is very powerful. The huge mahogany logs being unloaded appear to be so heavy that the ship itself seems to list to port as they are craned over the side. They are being levered into a cart to which two large and sturdy Clydesdale horses are hitched. In contrast to the traditional horses, the wharf is crisscrossed with modern railway tracks. Unloading is both mechanical and manual, and the scene is one of intense interest to a young boy bystander. The ship appears to be squat and solid, but the whole image also gives a feeling of movement and intensity. The mahogany being delivered to Melbourne would be intended for high quality furniture. In the 1930s Australia actually had a growing timber industry, but much of the eucalyptus wood was being utilised for mass produced furniture, and much of this furniture would then have had a veneer applied to it. The fact that it was economic to import this timber from the “Philippine Islands” – not a traditional trading market for Australia – reflects a Victorian economy that was strong enough to support a growing demand for good quality furniture Mahogany was described as a classic, strong hardwood, often used for dark opulent furniture. In the 1930s the importation of timber from Manila (Philippines) to Australia was a notable trade, particularly in Philippine Lauan (often referred to as Philippine Mahogany), which was used as a cheaper alternative to other hardwoods. 1930s furniture, dominated by the art deco style, used a mix of luxurious exotic woods like mahogany, macassar and ebony for high-end pieces, often veneered over less expensive woods such as walnut, birch and poplar, and with plywood, chrome and lacquer also popular for more practical, streamlined designs during the Depression era. By the mid 1930s timber mills were being relocated away from the immediate dock area, but the fact that these logs were being transported by horse-drawn cart implies that the load would not have had to be taken too far for milling. 1885 the Melbourne Harbour Trust Commissioners had decided that land in or near the city was far too valuable to be used as timber yards. Furthermore, large stacks of timber posed a fire risk. The Trust asked the Victorian Government to reserve a site on the east side of the Yarra River opposite Yarraville and Spotswood. Here, in 1889, the Trust began building six jetties and a wharf specifically for the landing of timber. Clydesdale horses were initially brought to Victoria from Tasmania in the 1830s, and with the 1850s gold rush they were imported direct from Scotland. Melbourne was from its earliest years an important centre of horse-breeding from both imported and colonial-bred stock, providing the well-built draught horse for pulling heavily loaded wagons, the harness horse for delivery work and drawing coaches, and the saddle-horse used for riding. Stud breeding facilities were advertised from the early 1840s. By the 1870s the horse export trade was thriving, and the Port of Melbourne was the country's busiest exporter of horses to Indian, Asian and New Zealand markets. Kirk's Melbourne Horse and Carriage Bazaar in Bourke Street first advertised for business in 1840, and by the 1850s Bourke Street West was famed for its horse bazaars and saleyards. The Victorian Clydesdale Horse Society reports that Clydesdale working horses were a vital part of Melbourne's infrastructure and agricultural industry in the 1930s, when they reached the peak of their popularity despite the increasing competition from mechanization. Their main roles and usage at this time were: • City Delivery: Clydesdales were a common sight for metropolitan deliveries, particularly for breweries (such as Carlton & United Breweries), milk runs, and bread deliveries. • Industrial Work: They were heavily used for hauling cargo at the docks, in construction, and at specialized sites like the Truganina Explosives Reserve, where they pulled wagons. • Agriculture: In surrounding rural areas, they were the primary power source for ploughing and agricultural machinery. • Specialization: By the 1930s, the Clydesdale was smaller and more compact than the Shire or Percheron breeds, making them ideal for navigation in urban environments. After the 1930s their numbers decreased due to the onset of WWI and mechanisation. Wartime petrol rationing led to a brief revival for the working horse, as suburban tradesmen, now used to motor delivery, took their old jinkers out of mothballs. By 1947, however, only 1.5% of city traffic was horse-drawn. In 1952 the large horse cartage company A. Kellet Pty Ltd sold its 250 horses and converted its Richmond stables to storage. In the 1950s at Station and Princes piers, wharf labourers refused to work with the six draught horses still being used to haul trolleys and which were soon superseded by the fork lift, semi-trailer and mobile crane. Where carefully trained horses had once shunted trains in city goods yards, a few hundred a week were now being killed at the abattoirs for pet and human consumption. The last MCC dray horse was withdrawn from service in 1958, but some of the few remaining working animals are used by the mounted police for crowd control at demonstrations and football games. The death knell had also sounded for the associated trades of farrier, saddler and blacksmith. Our photo, therefore, showing the wharf with both the haulage Clydesdales and the rail lines, is a strong visual summary of the social and economic changes experienced in Victoria in the 1930s and on towards the 1950s. Our photo is located at Victoria Dock (also known as Victoria Harbour) which is still an active component of Melbourne’s port system. In 1892 the West Melbourne Dock (later Victoria Dock) was opened, downstream and immediately west of the Spencer Street railway shunting yards. It contained a swing basin for ships, replacing the one which had been provided on the south side of the river, later to be the Duke and Orr dry dock, west of the Charles Grimes Bridge. Further west was the South Wharf along the river bank. The history of Victoria Dock is extremely well described by Ashley Smith in his 2 March 2022 article in Docklands News, and its accompanying aerial photo of the Dock taken in 1934. He writes: "In the early 1930s Victoria Dock was one of the biggest sites for trade and export in Melbourne. A constant queue of ships sailed in, unloaded their cargo, recharged and reloaded, then left for the next port. Around the time this photo was taken (found in a 1934 photo book), the trapezium-shaped basin had been through some changes since its construction in the 1890s. The 497-metre-long Central Pier, finished in 1919, now featured six sheds to house the ever-increasing volume of cargo. The entrance had also been widened in the 1920s to allow better access. Some of the berths featured three-ton jib electric cranes to help with loading cargo and a rail network connected to the State Railway service. By the time construction was completed, the dock was 39 hectares and hailed as the second-largest dock in the world (behind Cavendish Dock, Barrow-in-Furness). To further save costs, excavations were dug to a more reasonable seven metres below low water, instead of British engineer Sir John Coode’s recommended 8.3 metres. Even then, the costs were still around £900,000. It was envisaged, with the extra wharfage, that around thirty 90-metre ships could berth inside. On March 22, 1892, Victoria Dock was opened by Victoria’s Governor, the Earl of Hopetoun (later Australia’s first Governor-General) who opened the sluice to let the Yarra in. It took six days to fill the basin with The Leader newspaper estimating that it would take another six months to completely fill (March 26, 1892). In the end, it took nearly a year before the first ship was allowed to enter on February 20, 1893, when the steamer Hubbuck sailed in to unload 1200 tonnes of cargo in 15 hours. The Argus (February 23, 1893) reported that the ship’s captain, J. R. Brodie, called the Yarra “better than the Thames”, and compared Victoria Dock favourably to the Albert Dock (Liverpool)." This would be a good time to move our focus on to the Taiping, which is the transporter of these giant mahogany logs. The Taiping was a steel-hulled, single-screw passenger-cargo Chinese steamer, which today has the dubious legacy of being involved in a collision headlined as “The Chinese Titanic”. It was constructed by the Hong Kong and Shampoa Dock Company at its facility in Hong Kong, with completion in 1926 for service under the Australia Oriental Line. Her gross register tonnage measured 4,324 tons, reflecting her design for inter-island and coastal trade routes, accommodating both passengers and freight. She operated routes connecting Australian ports with East Asian destinations. As World War II approached, Taiping continued predominantly working the trade routes between China and Australia, until December 1941, when she evacuated women and children from Hong Kong to Manila just before Japanese forces overran the region. She then safely reached Australia despite enemy air raids. Taiping was then requisitioned by the Royal Navy and repurposed as a victualling stores issuing ship for the Eastern Fleet, supporting logistical needs in the Pacific and Indian oceans. Returned to the Australian Oriental Line in 1947, she underwent refitting and by mid-1948 was chartered to the Shanghai Shipping Company, and modified for greater passenger accommodation – approximately 500 passengers. In 1948/49 the Chinese Civil War took place. The Taiping departed Shanghai on 26 January 1949 as one of the final vessels evacuating civilians from to Keelung Harbour in Taiwan. Reports indicate that the Taiping carried double the rated capacity of passengers i.e. 1000. The ship carried families, military personnel, civilians, carrying personal belongings, gold and valuables in hope of resettlement in Nationalist Taiwan. It also held heavy cargo in the form of silver and gold bullion loaded by the Central Bank of China. Because of the risk of patrols, and to conserve fuel, the Captain took the ship away from the usual open-sea passage, and instead navigated along the coast. He also extinguished navigation lights to avoid detection. Shortly after midnight on 27 January 1949 the Taiping collided with the smaller cargo steamer Chien Yuan in the East China Sea near the Zhoushan Archipelago. The Chien Yuan was also operating in darkness. The subsequent collision was catastrophic. The Chien Yuan sank with in 5 minutes, with the loss of 72 of its 74 crew. The Taiping sustained severe structural compromise from the broadside strike and initially remained afloat, then made a swift descent into the freezing water, with no attempt at an organised evacuation. No formal recovery process was instigated, however a distress signal went out. 32 survivors were picked up by the Australian destroyer HMAS Warramunga (on patrol nearby), a passing US vessel found 2 more, and local Zhoushan fishermen retrieved others. In the end, only 37 people survived. The event is remembered as a poignant moment in the mass migration to Taiwan, with families tragically separated. A memorial to the disaster exists at the Keelung Harbour naval base on Taiwan. With its total of over 1,500 deaths, it constituted one of the worst peacetime maritime losses. It is sometimes referred to as the “Oriental Titanic” because of the similarly large loss of life and speed of demise with the RMS Titanic in 1912. A fictional depiction of this event appears in the John Woo movies “The Crossing (Part 1) (2014), and The Crossing II (2015), known in Chinese as “Taiping Wheel”. The narrative weaves a story around pre-disaster romances and wartime turmoil among passengers, culminating in the ship’s rapid sinking. “The production, a high-budget Sino-Taiwanese-Hong Kong co-effort, portrays the event as a microcosm of the 1940s Sino-Japanese and civil war legacies, though critics noted the melodramatic style prioritizing spectacle over historical precision.” In conclusion, it is nice to return to our photo, and observe the people involved in this moment. The dockworkers are, so typical of the 1930s, dressed in what looks to us like formal clothing – dark suits or coats, white shirts, and black hats. I am particularly drawn to the young boy, bare-headed, arms crossed, and so intent on the unloading process. He too is wearing a white shirt, black trousers and jacket, and black shoes. This is 1933 Melbourne – but the haircut he is sporting is now very “hipster” and modern in 2026 Melbourne. References: MAHOGANY FROM MANILA. (1933, August 15). The Age (Melbourne, Vic. : 1854 - 1954), p. 11. Retrieved January 30, 2026, from http://nla.gov.au/nla.news-article204377024 Wikipedia, Taiping steamer, https://en.wikipedia.org/wiki/Taiping_(steamer) Wikipedia, Victoria Dock, https://en.wikipedia.org/wiki/Victoria_Dock_(Melbourne) Docklands News, Ashley Smith, 2 Mar 2022, https://www.docklandsnews.com.au/victoria-dock/ Living Histories: Heritage Council of Victoria, Jill Barnard, 2008, Jetties and Piers, https://livinghistories.net.au/wp-content/uploads/2015/11/Jetties-ONL-intro_Part-1.pdf eMelbourne, Wharves and Docks, https://www.emelbourne.net.au/biogs/EM01612b.htm Australian Academy of Technological Sciences – Harvesting Wood, https://www.austehc.unimelb.edu.au/tia/225.html Old Treasury Building, On the Water – The Docks, https://tinyurl.com/3wkbk66m Old Treasury Building, On The Road, https://tinyurl.com/dw44yr3t Port of Melbourne, Victorian Places, https://www.victorianplaces.com.au/port-of-melbourne Docklands Heritage Study - Environmental History, https://mvga-prod-files.s3.ap-southeast-4.amazonaws.com/public/2024-05/docklands-heritage-review-thematic-environmental-history-1991.pdf eMelbourne, Horses, https://www.emelbourne.net.au/biogs/EM00723b.htm Victorian Clydesdale Horse Society, https://www.clydesdalesvic.org.au/history The Crossing, https://letterboxd.com/film/the-crossing-i/Photographer notations on slide: "Unloading Timber at Wharves 1933 Age B5"ships, shipping, timber industry, shipwrecks, horses, docks, wharves, 1930-1939, wars, docklands

There has been a fair amount of confusion about this object as the paperwork states that a 'greenstone' gavel with a maori head carving and plaque mounted on green nephrite stone' was gifted when in fact the gavel is made of wood with a silver plaque. There has been no suggestion made as to what happened to the greenstone gavel. We can assume that it was lost or stolen and replaced with a plain wooden one that we now hold at ANZCA. From the attached plaque the Gavel was gifted to the Faculty of Anaesthetists by the New Zealand Fellows of the Faculty in 1965. Plain highly polished wooden pestle sits on a central walnut block on a flat wooden board, a silver plaque is attached on a piece of nephrite stone to one side of the board.[silver plaque] PRESENTED BY THE / NEW ZEALAND FELLOWS / 1965 [in black ink on back of stand] 1992/9aotearoa, new zealand, wood, nephrite, corporate gift

Henry MORITZ (1931- ) Born Mainz, Germany Arrived Australia c1952 Henry Moritz was an experienced commercial artist when he left Germany for Australia. After working as a railwayman, coal miner, fruit picker and steelworker, he started teaching commercial art at the Ballarat School of Mines Technical Art School in 1963. He moved to the Mount Helen Tertiary Division, and was head of the Art School at the Ballarat College of Advanced Education (BCAE) when he produced this work. The Ballarat College of Advanced Education logo was derived from the Southern Cross depicted on the Eureka Flag, which was adopted by Ballarat College of Advanced Education in 1978. The logo was designed by former student Debra Garton, who graduated with a Diploma of Art and Diploma of Education. This item is part of the Federation University Art Collection. The Art Collection features over 1000 works and was listed as a 'Ballarat Treasure' in 2007.Farmed marquetry using fine woods chosen for their grains and reflective properties: silver ash, cedar, queensland walnut, grey bird's eye maple and African gaboon.art, artwork, henry moritz, marquetry, logo, southern cross, ballarat college of advanced education, available, stars

A Davis Imperial, walnut-fibreglass composite tennis racquet, with an open throat and large head. Racquet features ribbon whipping around shoulders, and plain leather handle grip. Model name features across base of head. Davis logo features along shaft TAD trademark features on rubber butt cap. Materials: Wood, Nylon, Ink, Glue, Lacquer, Metal, Ribbon, Leather, Adhesive tape, Rubber, Fibreglass, Painttennis