The regulator was sectioned by I. Philpott in 1962.The regulator, designed to protect anaesthetic machines against sudden changes in pressure, consists of two main, rounded bodies, joined by a short connection. The lower section consists of a valve and a nut on the end that can be adjusted to provide a secondary pressure range. The upper section shows the gauge, which has had part of its face removed to show the inner workings. The valve on the reverse side has also been sectioned.anaesthesia, gas, pressure

The T35 Austral was developed by Slingsby Aviation from the Slingsby T31 with the wing span increased and a larger rudder to improve performance. This was done in response to an order from an Australian gliding club. The Museum’s glider was built from a Slingsby kit imported from the UK in 1952 and assembled by the Waikerie Gliding Club. The glider came on the Australian register as VH-GFX in May 1956. It was later transferred to the Renmark Gliding Club. In 1968 it was acquired by the RAAF Gliding Club at Laverton, Victoria. The existing log book records for the Museum’s T35 Austral are incomplete. Nevertheless the information at hand shows that it was launched over 17000 times and spent about 2400 hours in the air. It would appear that the glider has not been used for many years, the last flight recorded by the RAAF Gliding Club for this aircraft being in September 1971. As far as is known VH-GFX is the only example of the type to be built. The Slingsby T35 is a modified Tandem Tutor two seat glider that had extensive service at a number of Australian gliding clubs over a period of approximately 15 years from the mid 1950s. The Slingsby T35 is an open cockpit, tandem, two-seater glider with high, pylon mounted two piece wing supported by double, wire braced, steel tube struts. australian gliding, glider, sailplane, slingsby, waikerie gliding club, renmark gliding club, raaf gliding club

This pennyfarthing was restored by council workers in the Numurkah Shire in 1970's. Unknown history beforehandRed framed penny-farthing bicycle - gold painted metal seat, small wheel at back with large one at front. Has copper handle bar with wooden knobs at ends

The 48 - 215 was the first vehicle produced by GMH specifically for the local Australian market. This vehicle later became better known as the FX. This vehicle was manufactured from 1948 to 1953. From here Holden continued to pursue the goal of producing an Australian car. This involved compromise with GM as Holden managing director, Lawrence Harnett, favoured development of a local design, while GM preferred to see an American design as the basis for "Australia's Own Car". In the end the design was based on a previously rejected post war Chevrolet proposal. The Holden was launched in 1948, creating long waiting lists extending through 1949 and beyond. The name ":Holden" was chosen in honour of Sir Edward Holden, the company's first chairman and grandson of J.A.Holden. Other names considered were "GeM", "Austral", "Melba", Woomrah", " Boomerang", "Emu", and "Canbra", a phonetic spelling of Canberra. Although officially designated " 48-215" the car was marketed simply as "Holden" The unofficial usage of the name "FX" originated within Holden referring to the updated suspension on the 48-48 215 of 1953.This was the first vehicle manufactured solely for the Australian market.4 Door sedan, two pane split screen windscreen, lifting boot and bonnet. Powered by an 132.5 Cubic inch motor.Holden Specialautomobile, holden, 1948, vintage, car

Part of Honeybun collection, Mitcham RSLExample of equipment from WWIWWI cigarette lighter from Messerschmit plane?LZ on end of casing

The box used by SEC Ballarat and Bendigo tram crews for holding their ticket outfits and making returns to the Revenue Clerks. Fitted with a padlock - see Reg. Item 3673. .Issued to a crew member with Traffic No. 62 - Roy Courtney. Each crew member was issued with a series of tins, A, B, and C which allowed for the various days and weekends to enable Revenue Clerks to accept returns and restock the tins with new tickets etc. Known to crews as "Two bottle boxes" - could fit two bottles of ale into them. The actual manufacturer is not known - could have been SEC workshops. See item 8917 for an MMTB tin.Has a strong association with tram crews and the ticket / revenue collection system. Tram crews used them to contain their tickets and to undertake their returns. Also used to "hide" bottles of ale., Has a strong association with tram crews and the ticket / revenue collection system. Tram crews used them to contain their tickets and to undertake their returns. Also used to "hide" bottles of ale.Metal box formed from four sheets of metal, spot welded together with a formed lid, hinged to box and fitted with a hasp and staple. Box painted black and lettered "62A". trams, tramways, crews, tickets, revenue journal

Black rubber ring with bulbous insert in middle of tube (tubing broken and rubber perished) Solid black bakelite attachment plus brown rubber attachment. Stored in a blue cardboard box with instructions printed on box. Called Ingrams Perfex Enema plus leather ring. 13 items to the set.medicine

Green woollen trousers issued. Size 5 Button up front with side pocket, and rear. Braces in blue striped elastic material with silver coloured clips stating Firemen and Police. Attached by leather straps buttoned onto trousers.trousers, clothing

This tin once contained Rawleigh's Allspice, a cooking ingredient. It was donated with other similar tins that were used by the donor’s mother who was married in 1932. It those times in Australia all manner of household items, including food and drink, were sold by hawkers (salesmen) who travelled from door to door in both suburban and rural areas. The donor remembered the tin on her mother’s pantry shelf. The Rawleigh Nutmegs label stated “Selected whole nutmegs not ground but granulated to preserve full strength and flavour.” The company had operated in Melbourne, Australia, and Wellington, New Zealand. W.T. Rawleigh & Co. was established by William Rawleigh in America in 1889 and later expanded into Australia. The company made a variety of household products in a factory in Collins Place, Melbourne, between 1930 and 1935. It specialised in medicines and remedies, food additives, cleaning products and toiletries. The company in Melbourne expanded into their factory in Dawson Street, Brunswick, in the mid-1930s. Independent salesmen, often referred to as ‘The Rawleigh’s man’, sold Rawleigh products door-to-door between the wars and after the Second World War in the Melbourne suburbs. Rayleigh’s products are still produced today. The tin is significant for its association with W.T Rawleigh, one of Melbourne’s strong growing manufacturers in period particularly between the World Wars. Rawleigh’s was, and still is, well known for its household and cleaning products, medicines, food additives and toiletries. The tin increases in significance for its use as a recognised object found in many Australian kitchens since early days. It gives a snapshot into domestic life and social norms of the pre and post war period in Melbourne The tin is significant for its association with a local family in the 1930s for the preparation of family meals. Rawleigh's rectangular Allspice spice tin, green, with directions for use on back and sides of container.Text “Rawleigh’s ALLSPICE” “The W.T. RAWLEIGH Co. Ltd.” “MELGOURNE / AUSTRALIA” “WELLINGTON / NEW ZEALAND” Motif: Man’s portrait in a circle. Other text includes information about spices.flagstaff hill museum, container, spice container, rawleigh company, tin container, kitchen item, tin, cooking ingredient, food container, grocery, allspice, rawleigh co.

A moulding plane is a specialised plane used for making the complex shapes found in wooden mouldings that are used to decorate furniture or other wooden object. Traditionally, moulding planes were blocks of wear resistant hardwood, often beech or maple, which were worked to the shape of the intended moulding. The blade, or iron was likewise formed to the intended moulding profile and secured in the body of the plane with a wooden wedge. A traditional cabinetmakers shop might have many, perhaps hundreds, of moulding planes for the full range of work to be performed. Large crown mouldings required planes of six or more inches in width, which demanded great strength to push and often had additional peg handles on the sides, allowing the craftsman's apprentice or other worker to pull the plane ahead of the master who guided it.A vintage tool made by an unknown maker, this item was made commercially for firms and individuals that worked in wood and needed a tool that could produce a ornamental finish to timber. The tool was used before routers and spindle moulders came into use to produce a decorative moulding for a piece of furniture, door trims etc. or other timber items that had to be accomplished by using hand tools and in particular one of these types of planes. Profiled planes came in various shapes and sizes to achieve the required decorative finish. A significant tool from the mid to late 19th century that today is sought after by collectors. It gives us a snapshot of how furniture and other decorative finishes were created on timber by the use of hand tools. Tongue and groove match plane with metal strip affixed with 5 screws Mc Vicar stamped on end and No 2. flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

This lifebuoy is part of the lifesaving equipment that would be carried on vessels in the late 19th and early 20th century. The strips of cork wood have been joined together to make the ring shape. A lifebuoy, or life-preserver, is used as a buoyancy device to keep a person afloat in the. It is usually connected by a rope to a person in a safe area such a nearby vessel or on shore. The lifebuoy is thrown to a person in distress in the water, allowing the rescuer to pull the person to safety. The lifebuoy is a made from a buoyant material such as cork or rubber and is usually covered with canvas for protection and to make it easy to grip. The first use of life saving devices in recent centuries was by the Nordic people, who used light weight wood or cork blocks to keep afloat. From the early 20th century Kapok fibre was used as a filling for buoys. Light weight balsa wood was used as a filler after WW1. In 1928 Peter Markus invented and patented the first inflatable life-preserver. By WW2 foam was combined with Kapok. Laws were passed over time that has required aeroplanes and water going-vessels to carry life-preservers on board. The lifebuoy is an example of equipment carried on vessels in the late 19th and early 20th century to help preserve life. There were many lives lost in Australia’s colonial period, particularly along the coast of South West Victoria.Lifebuoy, round cork filling inside white canvas cover with four reinforced bands. Four ropes are attached.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, life rings, lifebuoy, safety ring, life-saving buoy, ring buoy, life preserver, personal floating device, floatation device, safety equipment

BLUE CARDBOARD BOX CONTAINING HYPODERMIC NEEDLES. "NEW" "SOLILA" SURGICAL HYPODERMIC NEEDLES (MADE IN AUSTRALIA) THIS BOX CONTAINS 12 g23 "S 2" RECORD SOLE WHOLESALE DISTRIBUTERS : THE AMALGAMATED DENTAL (AUST) PTY LTD 124-126 EXHIBITION STREET, MELBOURNE C1 & 160 CASTLEREAGH STREET, SYDNEYON NEEDLES "23" & "SOL"local history, medical & surgery, medical, dental

A Julius Marlow shoe box containing a variety of objects - feathers for hair decoration, 2 paper fans, black buttons, empty box, and 3 spectacles in their cases.lydia chancellor, collection, hair decoration, feathers, hair ornaments, fan, buttons, spectacles, glasses, objects, ephemera, costume accessories

These marine diver's boots are made to weigh down the diver's feet to the bottom of the seabed, at the same time protecting his feet. The different pieces are joined with nuts, bots and washers. The boots are part of the protective clothing worn by marine divers to enable them to go to depths where others had not been. The Great Ocean Road along the southwest coast of Victoria is renown for its treacherous seas and tragic shipwrecks. Decades after the occurred divers began to explore the wreck sites and discovered hundreds of lost ships. The ships' skeletons and sprawled wreckage tell many stories of the type of ships used, the cargo and luggage carried onboard. They are valuable source of primary history. Many artefacts were recovered from local shipwrecks by the Flagstaff Hill divers and they have been preserved for historical records. Since that time many historic shipwrecks have become protected by Australian law. However, divers are able to still visit the sites.The boots are an example of diver's apparel in the 20th century and show the process of evolving protective and safety wear for underwater divers today.A pair of marine diver's boots. Boots are made of brass alloy and leather. The toes are metal and the metal soles are rippled. The sides have a short bar along the inner and outer sides of the foot, designed to fit a leather strap across the boot to hold it in place. A leather piece is attached to the back of each boot and extends around the ankle area to fasten with a buckle. flagstaff hill, warrnambool, maritime village, maritime museum, shipwreck coast, great ocean road, diver's boots, marine diving, underwater diving, deep sea diving, diving equipment, diving accessory, shipwreck exploring

The American Foundation for the Blind developed this new model in their experimental shop in 1932 and contracted with the typewriter manufacturer to produce the machines and continued production until 1947. It's sleek silver look was a change of look from the previously manufactured Hall Braille Writer, and improvements included a carriage return, the ability to add spaces between lines and a back space key. It was found in the Braille and Talking Book Library in South Yarra, Victoria, Australia and was used by either staff or volunteers at Vision Australia Library.Stainless steel braille writer in the shape of a typewriter. The braille writer consists of a heavy moulded machine with 6 black plastic keys.On front of writer: "American Foundation for the Blind Inc. New York." "Manufactured for the Foundation by L.C. Smith & Corona Typewriters, Inc." On back: "Licenced by Underwood Elliot Fisher company/ Serial no. 5-2422.braille equipment, assistive devices

Remington Typewrite All metal blackCHARTRES Pty Ltd Collins Street Melbourne Serial No. 23795 typewriter, remington

A general civilian Gas Mask for protection against gas warfare agents, tear gas, mustard gas etc..1) Face gas mask, enclosed with clear plastic eye pieces, attached cylindrical gas filter canister, head straps. .2) Protective cover, shaped canvas bag with webbing carry strap with adjustment buckle. .3) Small instruction booklet, 16 pages..1) Warning and instructions information printed on cylinder. .2) On bag, “U.S Non Combatant Gas mask M1A2-1-1” .3) On front cover, “Your Gas Mask”gas masks, civilian, u.s

William Greaves was once a prolific company that highly prospered in the 19th century during the boom of the tool and cutlery trades in Sheffield England as steel became more commercially available. William Greaves's works were situated at the Sheaf Works in the heart of Sheffield, at Maltravers Street, opening in 1823 and was known to be the largest business in this area at this time. The Sheaf Works made a range of tools and saws including cutlery, penknives and razors and also even made its steel in-house. The factory used its perfect position for water power being built on the edge of the Sheffield canal and also used the railway line nearby giving them the perfect opportunities for transporting its goods. The factory itself was also a revolution because it attempted to bring together as many cutlery manufacturing processes as possible together in one place, something that had not been attempted before. The money to build these huge works came from Greaves' trade with America, where they sent razors, table cutlery and sturdy Bowie knives. This allowed the Greaves’ to build the factory and expand their production, which made them even more money. This made William Greaves very rich indeed, and it was reported that when he died in 1830 he left each of his five surviving daughters £30,000 each, an astronomical sum at the time. In today’s money that is approximately £2.3 million. The firm finally dissolved in 1850, but Sheaf Works continued to be used by many cutlery manufacturers until the 1980s. With most of the buildings still standing today.A significant item made by a successful cutlery manufacturer in England during the first half of the 19th century. This company undertook many new processes to streamline cutlery production and introduced innervations regards working with steel that are still in use today. This item is now regarded as a collector's item given the company ceased trading in 1850. jigger/hollowing knife with internal bevel, Electro Boracic Steel. Stamped 3.1/2″ William Greaves, Sheaf Works, Sheffield flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, cooper's jigger, howeling knife, wm greaves & sons

Pittock collection: timber carpenter's level * level made of hardwood, with brass trims and two glass level bubbles * level 505 mm L x 80 mm W x 32 mm D * P incised on both sides of the level * no manufacturer's details visible Item stored in Pittock coach builder's box, reference 13000.1.

From the Betty McPhee sewing collectionFour cardboard tubes of coloured glass headed stems or pins used by dressmakers etc to pin clothes etc prior to sewing. I box of Dandy household pins.Cross Five Brand. "Dandy" regd Trademark Electroplated steel household pins Australian manufacturehandcrafts, equipment

Glass manufacturing has evolved over thousands of years. Glass making has been traced back to 3500 BC in Mesopotamia. The earliest known glass objects were beads, perhaps made by accident while working with metal. In the late Bronze Age, several civilizations discovered how to make vessels and glass bottles by wrapping threads of melted glass around cores of sand or clay. Later, moulds were used to form dishes and table wares. Around the 1st century BC, glassblowing was discovered. This made glass containers less expensive than pottery. Mould-blown glass, the process of blowing a piece of molten glass into a wooden or metal mould, was invented during the 1st century AD. This technique was faster with more consistent results. It paved the way for mass production. It wasn’t until the late 1800s that the production process to become more efficient. In 1887, a company in England created a semi-automatic process that could produce up to 200 bottles an hour. This process has been refined to the point where modern machines can yield more than 600 containers per minute. Blown vs. Manufactured Glass Bottles Nowadays, glass bottles, jars, and cups are usually manufactured on a bigger scale than is found in individual glassblowing studios. If we still depended on hand-blown glass for all of our glass containers, we would see some major differences in the process of creating bottles and jars. First, there's the time. Hand blowing glass takes a significant amount of time, even for one simple container. In contrast, hundreds of jars per minute can be made using modern technology. This leads to the second advantage: price. Because of the automated and streamlined process, the price for manufactured containers is much lower than that of hand-blown glass. Third, manufactured bottles will be much more consistently uniform than bottles blown by hand. Automated glass manufacturing produces nearly identical batches of jars. Glass blowing is awesome for unique, beautiful pieces of art. But for lots of lower priced and uniformly shaped containers, automatic manufacturing is the preferred method to create glass bottles and jars. https://www.containerandpackaging.com/resources/glass-bottles-brief-history The invention and development of glass for domestic items including bottles, has been nothing short of revolutionary. The use of glass bottles, that could be easily washed, led to improved hygiene, and mass manufacturing of drinks of all types, including milk, cordial and alcoholic beverages.Green Glass Bottle Possibly a ginger beer bottle.Concave indentation at the base. Also on base are two raised lumps. flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, glass

Australian webbing khaki colourCompass Pouch, brass button and brass belt keepers.equipment, compass, webbing

Collection of 10 nails with square shaft end to end and a kink.archaeology, historic building, former royal mint

Used to hold hot steel whilst being forged.rural industry, farm machinery, trades, blacksmithing

Contained a stain for the darkening of all equine leather pieces used Ca 1900Imported and retailed bu Holden and frost Ca1900Squat beige ceramic bottle with corked top, used to contain a stain for equine leather bits and piecesShowing saddle stain with trade mark of fox head. label in very poor condition.leather, stain, ca1900

The blacksmith leg vise is also called the "solid box vise" and is one of the most important tools in the blacksmith's shop. It firmly holds hot iron while it is hammered, chiseled, or twisted. These are the only vises that are designed to take this kind of use day in and day out. A small 30-pound blacksmith's vise can survive pounding that would wreck a much heavier cast iron bench model. Three things make a blacksmith's vice special. One is that they are forgings, not cast iron or ductile iron. The second is the leg that provides support to the floor or from a sunken post. The last is the hinge, while not a perfect way to construct a vice the pin joint is durable and can take a considerable beating. If sheared it is easy to replace. These things all combine into a tool that can take decades of heavy use and abuse. Most in use is one to two hundred years old.Some of these vises were made by specialists such as Atwood of Stourbridge England, Steel City and Columbian in the U.S. and others were made in anvil manufacturing plants such as "Mousehole Forge" and "Peter Wright" in England and "Fisher-Norris" and others in North America. The design of these vises right down to the last chamfer seems to have been perfected in the 1600s and remained more or less the same until the 20th century. The bodies are forged wrought iron or mild steel and they have hard steel surfaces welded into the jaws. The jaws have little or very shallow serrations which are generally worn off.Around the turn of the 20th Century during the hey-day of the blacksmith shop in North America, these tools were considered so standard a commodity that they were sold without reference to the manufacturer. Very few were even marked with the maker's name. Size is best defined by weight as there is some variation in jaw size from manufacturer to manufacturer. They were sold by the pound and are still best judged by the pound.A vintage tool used in a Blacksmiths shop during the early 19th century to the beginning of the 20th century. Regarded as a significant into social history of the time.Leg Vice attached with screws to bench via a block of wood. Has large metal pole which practically reaches the floor. Also has a metal device to either tighten or slacken vice.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village