The T35 Austral was developed by Slingsby Aviation from the Slingsby T31 with the wing span increased and a larger rudder to improve performance. This was done in response to an order from an Australian gliding club. The Museum’s glider was built from a Slingsby kit imported from the UK in 1952 and assembled by the Waikerie Gliding Club. The glider came on the Australian register as VH-GFX in May 1956. It was later transferred to the Renmark Gliding Club. In 1968 it was acquired by the RAAF Gliding Club at Laverton, Victoria. The existing log book records for the Museum’s T35 Austral are incomplete. Nevertheless the information at hand shows that it was launched over 17000 times and spent about 2400 hours in the air. It would appear that the glider has not been used for many years, the last flight recorded by the RAAF Gliding Club for this aircraft being in September 1971. As far as is known VH-GFX is the only example of the type to be built. The Slingsby T35 is a modified Tandem Tutor two seat glider that had extensive service at a number of Australian gliding clubs over a period of approximately 15 years from the mid 1950s. The Slingsby T35 is an open cockpit, tandem, two-seater glider with high, pylon mounted two piece wing supported by double, wire braced, steel tube struts. australian gliding, glider, sailplane, slingsby, waikerie gliding club, renmark gliding club, raaf gliding club

Smokers are used to calm bees. This is done by putting some kind of fuel into the chamber (pine needles, hessian, anything that smokes a lot when it burns), lighting it, then puffing the bellows to bring forth the smoke. The smoke has a calming influence over the bees, and helps stop them from stinging. The guard around the outside is to prevent burns via contact with the hot chamber.Circular canister, metal, with spout attached. Connected by metal struts to circular bellows. Bellows are missing. Canister very rusty, extensive use wear. Lid is fused to canister.rusty, smoker, antique smoker, beechworth honey

A white wicker child's rocking chair with a curved top and arms joined in one piece. There are two single curved wooden struts on either side in the middle to support the arms.rocking chairs, furniture

The queen bee cage is designed to hold a queen bee, and up to three or four escort worker bees. The design allows for adequate ventilation, and has a spot for 'queen candy' -candied honey- to block one end. The queen is placed in her new hive inside the cage, and once the queen candy has been eaten through -allowing her access to the hive- the hive has become accustomed to her smell and accept her. Bees could be sent through the post in this cage.Mesh cage stapled onto top and bottom metal bands. One metal strut running between top and bottom. Base is metal, larger than lid. Lid is wooden, with circular hole.cage, queen, bee, transport, queen bee cage, beechworth honey

1905-1933.The bandage winding machine wound calico bandages for patient use. A sheet of calico was torn into strips of differing widths and a length of around 8 feet or 240 cm. The bandage was wound around the handle shaft, by hand initially, to get purchase, then the handle was turned until the bandage was tightly wound. Bandages were reused after being washed, dried and rewound on the machine.The bandage winding machine wound a bandage more tightly than could be achieved by hand, allowing more effective bandaging. An open wooden frame with six horizontal wooden struts. At the top of the frame is a metal shaft with a bakelite handle which winds and holds the bandage. The frame is on a wooden stand. This stand has an aditional shelfUnder the wooden stand is written: Tutorial Dept. Alfred Hospital.bandages, bandage winding machine, nursing practice, alfred hospital

Used by Mrs Duncan's Grandfather when he was a carpenter on the Clipper Ships that sailed between England and Australia in the 1870sSea chest - raised curved lid, wooden slats 7cm apart. Metal struts across lid and down sides. One metal lock, 2 catch locks. Handle each end.personal effects, travel goods

Leaf shaped fan made of strands, possibly raffia- woven around a central bamboo strut which forms the cone of the handle. Coloured design of indigo and dark blue formed by use of coloured strands.handcrafts, basketwork, costume accessories, female

Smokers are used to calm bees. This is done by putting some kind of fuel into the chamber (pine needles, hessian, anything that smokes a lot when it burns), lighting it, then puffing the bellows to bring forth the smoke. The smoke has a calming influence over the bees, and helps stop them from stinging. The guard around the outside is to prevent burns via contact with the hot chamber.Circular canister, metal, with spout attached. Connected by metal struts to bellows. Bellows have wooden front and back joined by leather that is attached by metal. Very rusty; lid fused shut. Extensive use wear.rusty, smoker, antique smoker, beechworth honey

1905-1933.The bandage winding machine wound calico bandages for patient use. A sheet of calico was torn into strips of differing widths and a length of around 8 feet or 240 cm. The bandage was wound around the handle shaft, by hand initially, to get purchase, then the handle was turned until the bandage was tightly wound. Bandages were reused after being washed, dried and rewound on the machine.bandages, bandage winding machine, nursing practice, Alfred HospitalAn open wooden frame with six horizontal struts. At the top of the frame is a metal shaft which winds and holds the calico bandage. . It sits on a solid wooden base, 4 curved corners. 2 solid wooden end plates.Marked from Ward 1 on outside of end plate in black inkbandages, bandage winding machine, nursing practice, alfred hospital

Sepia photograph showing the steamer S S Gippsland being built at the shipyard at Paynesville. Hull and framework in progress, struts supporting hull in position, timber stacked on site, eleven workmen, McMillan Strait and Raymond Island in background. Paynesville VictoriaBuilding of the S S Gippsland at Paynesville in 1907. J C Bull co-author of this book is the young apprentice second from the left in the middle. ships and shipping, slipway, boat building

The Alexander Schleicher K4 was designed in the mid 1950s by Rudolf Kaiser as a club training glider and several hundred were built. The Australian Gliding Museum’s K4, VH-IKK, serial number 55, was built in 1957 and purchased by the RAF Air Training Corp. U.K. After some years it was sold to a New Zealand Gliding Club and in 1990 with over 4800 hours, number of launches unknown, it was purchased by the Brisbane Valley Soaring Club and in 1994 was transferred to the Far North Queensland Soaring Centre who operated it from the Mareeba airfield. On 9 January 2000 it was donated to Vintage Gliders Australia by Kevin Sedgman at a presentation ceremony with Alan Patching receiving the glider during the Rally at Lake Keepit. It has been flown regularly at vintage glider rallies and on several occasions at Museum open days. However, it has subsequently been grounded on account of potential structural defects. VH-IKK is one of two K4s in Australia, the other being VH-XJP which is believed to be in storage in Queensland in a damaged condition. When restored, this exhibit will be representative example of the AS-K4 glider-sailplane type.Tandem two seat high wing strutted glider consisting of wood with plywood and fabric wings, tailplane / elevators, fin / rudder, and tubular steel framed, fabric covered fuselage. Prior to restoration work, the glider was finished in a white, green and yellow paint scheme. “Vintage Gliders Australia” name in white lettering on fuselage sides and registration VH-IKK in black lettering on rudderaustralian gliding, glider, sailplane, alexander schleicher, k4, kaiser, raf air training corp, brisbane valley soaring club, far north queensland soaring centre, vintage gliders australia, sedgman, patching

The item was given to Capt R.A. Hanson VX111070 by Japanese POW's in camp in New Guinea. Refer Cat No 5646.3P for his service details.Cigarette case oval shape aluminium, made from an aeroplane strut, each end is covered in perspex, two parts slide together over an inner section, all around has been hand engraved withJapanese symbols, ladies in bathers, mountains and palms."Japanese symbols"accessory, cigarettes, trench art

Pink, blue, cream and olive coloured material on sunshade. Dark crown shaft with lighter coloured handle. Wodden handle has twisted leater strand with fringed tassel for hanging. Material and metal closing catch. Paragon, S. Fox and Co. Limited on inside metal strutS. Fox and Co. Limitedcostume accessories, clothing accessories, umbrella

The Hutter H17 is a small single seat glider with a wing span of 9.69 metres, designed in 1934 by Wolfgang Hutter, for flying in the Austrian Alps. Construction of the museum’s example, “Sweetwings” (now registered as VH-GQM), commenced in Perth in 1949. It is one of two Hutter H17 gliders built in Western Australia by N.J. Wynne and A.G. Milligan at the time – the other “Fleetwings” (formerly VH-HDQ and since re-registered as VH-GXV) is located at Millicent, South Australia. Ownership transferred to G.R. Reichelt of Tocumwal New South Wales and later to D.B. Hunt of Thornbury in Melbourne and later Mt Isa, Queensland. It was acquired by Bill Riley of Tocumwal who donated it to the Museum. The glider was last flown on 25 October 1979 at Tocumwal. This exhibit is an example of a 1930s small wood and fabric glider that was designed in Austria for hill soaring. It is a simple design that became a popular choice for home building in the post war years in Australia when gliding as a sport was in recovery. Some examples are still flying.Small single seat glider. Fuselage and wing struts are painted yellow. Wings, rudder and tailplane / elevator are primed with pink dope. It has an open cockpit with small clear Perspex wind screen. Instruments include airspeed indicator and altimeter tucked neatly under front edge of the cockpit rim.australian gliding, glider, sailplane, hutter, sweetwings, fleetwings, reichelt, riley, wynne, milligan

The ensignette was a vest pocket camera. The Ensignette was one of the very characteristic camera types of Houghtons Ltd., London. This strut folding roll film camera of Houghton's "Ensign – British made" brand was an ingenious construction, a real vest pocket item when folded. One of the round framed impressions on its front plate says that it was based on patent 28464 of the year 1907. The Swedish engineer Magnus Neill had designed this first British all-metal camera of which ten of thousands were made. The camera was launched before Christmas 1909. It was ordered by distributors all over the world, for example by G. Gennert. (Ref: camerapedia) The Ensignette was very popular because it was one of the first practical, compact cameras at an affordable price to the average man. A miniature bellows, roll film, camera - Ensignette No. 2. It is black metal with folding bellows. On the front is an aperture control knob. There is a window at the back for the film number.Flag with Union Jack Ensignphotography ensignette camera

Edward Pyke and Jean Maurice Glauser invented this machine with the intention of enabling the easy and quiet production of Interpoint Braille. Although widely agreed to be one of the best Braille machines of its time, production of the machines was stopped during the Second World War because of rationing and high material costs. The machine has a keyboard arrangement at one end, the other end folds out to form a platform which is held up by a metal strut with rubber capping. An upward writing model, the paper feeds from the rear and passes under the space bar. The machine has no paper feed rollers. The only movement is that of the carriage that moves from left to right.Painted metal machine with metal keys that move a carriage across inserted sheets of paperRoyal National Institute for the Blind 228 Great Portland St London W1 Pyke-Glauser Braille Writer PG 48braille equipment, royal national institute for the blind

This is a teacher's desk which came from Woodford State School. The school began in 1854 in a private dwelling with a new building constructed in 1874. The school still operates today.This is a very fine example of an early 20th century school teacher's desk. As it comes from one of the earliest schools in the district, it is of considerable significance.This is a wooden desk, now varnished, with a lift up, slanted lid with brass hinges and a brass key hole. On the top right hand side is a brass insert with a porcelain ink well. The desk has four turned legs with end struts. The desk lid may be made of pine but the rest of the desk seems to be made of a different wood. There are signs of old borer on the left hand front and the curved part on that side is missing.woodford state school, teachers desk, wooden teachers desk

This camera is a folding one, the Ensignette No 2 model made by the British firm of Houghtons Ltd which was originally a glass warehouse founded in 1834. The firm of George Houghton and Sons, dating from the late 19th century, established their camera business at Ensign House in London in 1903 and the Ensignette No 2, designed by a Swedish engineer, was introduced in 1912. Eastman Kodak of America produced a film for this model. This camera was a popular one with amateur photographers and the general public, being affordable, compact and easy to use. This camera is retained as an example of a British-made folding camera dating from nearly 100 years ago. It will be useful for display..1 This is a black metal camera which is rectangular in shape. It is a strut folding rollfilm camera with a lens that is folded inside in a thin leather concertina or bellows covering. It has the maker’s name and logo etched into the front of the camera. The logo is a flag with the British Union Jack in one corner and the word ‘Ensign’ inside the flag. The metal on the back of the camera is rusted. .2 This is a brown leather cover for the folding camera described above. It has a top lid flap which closes with a metal stud and a leather handle stitched on to the sides of the case. The cover is much worn and scuffed. Ensignette No 2 Ensign British Made Made by Houghtons Ltd England vintage cameras

The wooden crate contains a set of patterns or moulds that were once used at Briggs’ Brass Foundry for making sand moulds. The traditional method of sand casting is over 2000 years old. It is part of a crafted process used to make brass and copper alloy goods suited to marine use; bells, boat hooks, cowls, propellers, handles, lids, rowlocks, hooks, letters, bolts, rail holders, brackets, deck plates, flanges, rudder guides, portholes and covers. Briggs’ Bronze is a copper-based alloy made from local ingots of copper, tin, zinc and lead in carefully measured quantities. The finished product is non-corrosive and can last indefinitely. The crate of patterns was donated by the Briggs family in the early years of Flagstaff Hill, along with other related items such as brassware, tools and machinery. The donated items were displayed in a simulated Brass Foundry in the Village. The items were on show from the completion of the building in 1986 until 1994 when the building was repurposed. The patterns represent the trades of foundering and metalwork, both supporting maritime industries such as shipwrights and boatbuilders. Farmers, manufacturers and other local industries also needed the castings made by foundries. The Brass Foundry display was one of the early ‘working craft’ shops at Flagstaff Hill. It included a historic Cornish chimney that was set up as a working model, telling the story of heat from furnaces to smelt metal, which would then be poured into the sand moulds. This chimney is made from specially curved bricks and is about two-thirds of its full height when originally located at the Grassmere Cheese factory. HISTORY of BRIGGS BRASS FOUNDRY: - The family business was founded in 1912 by Herbert Harrison Briggs (1963-1931) with his son George Edward Briggs, trading as Briggs & Son Foundry at 70 Wellington Street, Collingwood. Younger son Cyril Falkiner McKinnon Briggs joined the foundry in 1922, and it was renamed H H Briggs & Sons Foundry. Both sons ran the firm after Herbert’s death in 1931, making products mainly for marine purposes. They became Bell Founders in 1936 and were known for their specialty of high-quality ship bells. They produced miniature varieties of these and other decorative items such as small propellers. The firm became known as Briggs Marine Foundry. The great-granddaughter of Herbert Briggs inherited the Briggs Brass Bell, similar to the one at Flagstaff Hill. Cyril became the sole family member of the firm in 1965. The Briggs Marine was an exhibitor at the 1965 Boat Show, where he advertised as “non-ferrous founders” and “Bell Specialists”. The foundry relocated to Chesterville Rd, Moorabbin. Cyril passed away in 1967. It is thought that either Cyril or his business partner Frank Lee donated the objects from the Briggs’ Foundry around the time when the business moved to Moorabbin. However, Flagstaff Hill hadn’t been thought about until 1972. The donated items were registered in the Collection in 1986 but they could have been in storage from an earlier date. In October of that same year, Briggs Marine restored Schomberg Bell, a shipwreck artefact from the collection at Flagstaff Hill. Peter Oram, who had worked for the previous owners of Briggs Marine as a fitter and turner, took over the firm in 2014, reviving some of the old casts for current use. The business is now located at Seaford in Victoria and is part of Alliance Casting & Engineering Solutions (Alliance Casting Pty Ltd). In 2016 the original Collingwood Foundry building was repurposed as a thriving business hub named The Foundry. The crate and its patterns are significant for their association with brass foundries locally and generally in coastal areas of Victoria. Marine industries such as ship and boat building rely on good quality castings for their machinery, equipment and fittings. The patterns are associated with the long-running firm, Briggs Brass Foundry, that specialised in cast goods for the marine industry, ready to supply the needs for once-off or mass-produced items. Their products would have been fitted to sail and steam vessels along coastal Victoria including Warrnambool. Briggs Marine is also associated with the Schomberg Bell in Flagstaff Hill, restoring the bell to is former state to show an example of the bell from a luxury mid-19th century vessel. The craft of sand-casting from carved wooden patterns to create metal is an example of skills from the past that are still used today. Wooden rectangular crate with removable wooden lid. Inside is a set of wooden patterns of various shapes and sizes for making sand moulds in a metal foundry. The crate is made from thick wooden planks nailed together. The extended wooden struts on the long sides form a frame to hold the wooden lid. A pair of metal handles are at each short end of the crate, fixed with strong metal bolds. Between each pair of handles is an inscription stamped into the wood. The underside of the crate has red paint splashes. There are insect holes in the wood but no sign of current infestation. Stamped: "H.33 / II" (H may be N or a square B)flagstaff hill maritime museum and village, great ocean road, shipwreck coast, pattern, mould, foundry, brass foundry, metal foundry, crate, box, wooden container, briggs, traditional method, trade, sand cast, cast, brass alloy, copper alloy, marine equipment, marine tools, marine fittings, briggs' bronze, copper tin zinc lead, non-corrosive, briggs family, brassware, metalware, foundering, metalwork, maritime, casting, cornish chimney, curved bricks, grassmere cheese factory, 1912, herbert harrison briggs, h h briggs, george edward briggs, briggs & son foundry, collingwood, cyril falkiner mckinnon briggs, cyril briggs, h h briggs & sons foundry, bell founders, schomberg bell, alliance casting & engineering solutions, collingwood foundry, ship chandlers, marine products, flagstaff hill, warrnambool, maritime museum, maritime village, briggs & son brass foundry, briggs marine, moorabbin

The Slingsby T31 is a two seat training glider that came available in 1951. It is, in effect, a two seat version of the single seat Kirby Tutor. The T31 was marketed by Slingsby Sailplanes both as complete aircraft and kits of parts for assembly. The Australian Gliding Museum’s example (currently registered as VH-GDB) is one of five of this type to grace Australian skies. Three including GDB were assembled in Australia from kits supplied by Slingsby’s in England, the other two were delivered as completed airframes. To date only four remain of which two are airworthy. This aircraft began flying in at Caversham in Western Australia (the then home of the Gliding Club of Western Australia) in July 1956. It was badly damaged in a crash in June 1958. The wreckage was sent to Schneiders in Adelaide for repair. However, the Club decided against having the repairs done, opting instead to buy a new ES52 Kookaburra. After a couple of years, the wreck was purchased by a member of the Waikerie Gliding Club whereupon the glider was rebuilt with some modifications, including a more rounded and better streamlined fuselage nose. It returned to the air in October 1961 at Clare in South Australia. The ownership of VH-GDB passed through a number of clubs, including at Dubbo in New South Wales, Wimmera in Victoria and Pioneer Valley at Mackay in Queensland. Eventually, it came into the hands of Bill Riley of Tocumwal in New South Wales who held it in storage for many years. Riley donated the aircraft to the Museum. It has been restored to airworthiness and is flown at vintage glider rallies and on Museum open days. This exhibit is an excellent example of a Slingsby T31 Tandem Tutor, a type of glider that was used by a number of clubs in the 1950s and 1960s for dual training of pilots to the solo capability.The Slingsby T31b Tandem Tutor is an open cockpit, tandem, two-seater glider with high, pylon mounted two piece wing supported by double, wire braced, steel tube struts. The glider is fitted with a main wheel, rubber-block sprung, wooden nose skid and steel leaf sprung, brass shod tailskid. The basic controls of aileron, rudder and elevator are not supplemented with pitch trim. Wing lift spoilers and both aerotow and winch releases are fitted. The instrument panels in both cockpits are fitted with an airspeed indicator, cosim variometer and altimeter. This red and silver painted wood and fabric covered aircraft is in excellent condition having been restored to full airworthy status by the Australian Gliding Museum. SLINGSBY – T31b (nose – both sides) DB Australian Gliding Museum (rudder – both sides) It has been given Serial Number GFA/HB/12 and is registered as VH-GDBaustralian gliding, glider, sailplane, slingsby, tandem tutor, t31, gliding club of western australia, waikerie gliding club, wimmera soaring club, pioneer valley soaring club

Henry Beater Christian (1886-1962) , was a descendant of one of the earliest settler families in Kew. Employed at the Kew Asylum as a 'public servant', he was a skilled amateur photographer, photographing numerous scenes in Kew and on his travels around Victoria. The majority of his photographs date from 1916 to 1929. His finest photographs are housed in two photograph albums. Rare photograph of the demolition of the Zig-Zag Bridge linking the two asylums on either side of the Yarra River.Digital copy of a photograph from page 16 of the 47-page photograph album containing 261 gelatinous silver images, loaned by Diane Washfold with permission given to digitise and hold a copy in our collection. The Zig-Zag Bridge linked the grounds of the Yarra Bend and Kew Asylums. The wooden bridge was constructed in the 1870s and lasted through numerous floods until its destruction in 1929. A horizontal structure, the walkway was reached via a wooden staircase on the Kew bank of the river. The steps were required due to the different levels of the banks on this stretch of the river. This is a photo of the bridge showing the level of destruction caused by the initial damage from the flood and subsequent dismantling of the horizontal struts and walkway, prior to to its destruction by fire."Demolishing Zig-Zag / 6. 1929"henry beater christian (1886-1962), landscape photography, kew (vic.) — yarra river, christian-washfold collection, photograph albums, zig-zag bridge

Henry Beater Christian (1886-1962) , was a descendant of one of the earliest settler families in Kew. Employed at the Kew Asylum as a 'public servant', he was a skilled amateur photographer, photographing numerous scenes in Kew and on his travels around Victoria. The majority of his photographs date from 1916 to 1929. His finest photographs are housed in two photograph albums. Rare photograph of the demolition of the Zig-Zag Bridge linking the two asylums on either side of the Yarra River.Digital copy of a photograph from page 16 of the 47-page photograph album containing 261 gelatinous silver images, loaned by Diane Washfold with permission given to digitise and hold a copy in our collection. The Zig-Zag Bridge linked the grounds of the Yarra Bend and Kew Asylums. The wooden bridge was constructed in the 1870s and lasted through numerous floods until its destruction in 1929. A horizontal structure, the walkway was reached via a wooden staircase on the Kew bank of the river. The steps were required due to the different levels of the banks on this stretch of the river. This is a closeup view of the bridge showing the level of destruction caused by the initial damage from the flood and subsequent dismantling of the horizontal struts and walkway, prior to to its destruction by fire."Demolishing Zig-Zag / 6. 1929"henry beater christian (1886-1962), landscape photography, kew (vic.) — yarra river, christian-washfold collection, photograph albums, zig-zag bridge

Henry Beater Christian (1886-1962) , was a descendant of one of the earliest settler families in Kew. Employed at the Kew Asylum as a 'public servant', he was a skilled amateur photographer, photographing numerous scenes in Kew and on his travels around Victoria. The majority of his photographs date from 1916 to 1929. His finest photographs are housed in two photograph albums. Rare photograph of the demolition of the Zig-Zag Bridge linking the two asylums on either side of the Yarra River.Digital copy of a photograph from page 16 of the 47-page photograph album containing 261 gelatinous silver images, loaned by Diane Washfold with permission given to digitise and hold a copy in our collection. The Zig-Zag Bridge linked the grounds of the Yarra Bend and Kew Asylums. The wooden bridge was constructed in the 1870s and lasted through numerous floods until its destruction in 1929. A horizontal structure, the walkway was reached via a wooden staircase on the Kew bank of the river. The steps were required due to the different levels of the banks on this stretch of the river. This is a view of the bridge showing the level of destruction caused by the initial damage from the flood, the subsequent dismantling of the horizontal struts and walkway, and the setting on fire of the remaining structure."Demolishing Zig-Zag / 6. 1929"henry beater christian (1886-1962), landscape photography, kew (vic.) — yarra river, christian-washfold collection, photograph albums, zig-zag bridge

The collection of thirteen model horse drawn vehicles were carefully handmade by Mr Chas W Davis 1925 - 2002. He was a talented artist and saw doctor. This model of a horse drawn Piano Box Buggy replicates the vehicle that enjoyed respect from the public during the 1880 and early 1900's. A model of a red and black Piano Box Buggy c.1860 which was a lightweight two wheeled one passenger open horse drawn carriage with a black canopy roof where the driver sat behind. It has two large and two smaller gold painted spoked wheels with black rims, brown painted seating, two gold coach lamps and a black patterned footrest in front of the driver. The canopy has thin gold struts to open and close it depending on the weather. There are two long brown wooden shafts on each side to surround the horse. It has a model of a biscuit coloured horse with a white tail and mane with the necessary horse tack for carriage use to help the driver communicate with the horse. It was also known as the 'Bonner Buggy' and had many variations. Coach builders designed and made their own style, giving it their own name. There could have been scores of different Piano Box buggies.replicas, models, scale models, vehicles, carriages, horse drawn vehicles, toy horses