In the mid 1960s, Amalgamated Wireless Australasia (AWA) was asked to design a solid-state replacement for the PYE TRP-1 in collaboration with the FCV. The new transceiver was to be more powerful than the TRP-1, with an output power of about 10-12W (compared to 1.5-2W). The set also had to be capable of being used as a walkie-talkie, as well as being suitable for use in a vehicle The FP-1 is a single channel radio that has a crystal for each channel, and an IF frequency of 45 5khz. The receive crystal is 455khz higher than the transmit crystal. It is completely transistorised, and uses AWA and RCA brand transistors. A later version was called the FP5 and had five channels. Introduced to the FCV in the mid 1960sRadio Receiver Forest Phone FP-1 radios, forests commission victoria (fcv)

After the 1939 bushfires, the Forests Commission invested heavily in a radically new communications network. After suffering some inevitable delays due to the War, radio VL3AA switched into full operation in October 1945 proudly beaming out 200 watts across the State. The communication systems were regarded at the time to be more technically advanced than the police and the military. These pioneering efforts were directed by Geoff Weste, and later technical experts like Rex Philpot, John Whitehead, Charlie Reisinger and many others who designed, built and repaired most of the radio equipment. There was a dedicated radio laboratory at Surrey Hills in Melbourne.Radio setSTC Star Radio Telephone Type FR5.1.25-STradios, forests commission victoria (fcv)

These boots were manufactured by Oliver Stevens in Ballarat to the Forests Commission's own specification. Safety boots were a bit "hit and miss" back in 1981. As well as the steel toe caps these boots had a screwed, glued and stitched Sherpa-pattern rubber nitrile sole. The sole was oil resistant and didn't melt on hot coals. The yellow heels signified safety boots. There were two styles with different leather and staff were all personally fitted and given their choice of style. The only thing that has fundamentally changed over 40 years is there is much more choice and comfort in boots today. These boots proved to be the catalyst for boot manufacturers realising there was a market outside of the armed forces not being served. Ankle injuries along with elastic sided boots were virtually eliminated by these boots. The iconic Tasmanian company, Blundstone, had a work boot called "Forester" at the time. It had won an Australian Design Award and had a bonded Sherpa sole. Unfortunately, the soles tended to separate from the boot under field test conditions. Eventually they perfected the process Oliver Stevens' main issue was not being able to recruit enough workers to meet the increased demand. Info: Trevor Brown.First safety boots issued to Victorian forest firefightersYellow Back safety boots with leather laces. FCV marked on the heel fire fighting, bushfire, forests commission victoria (fcv), protective clothing

Foresters usually measure the diameter of trees at Breast Height – traditionally 4 foot, 6 inches – now 1.3 m – which is termed Diameter Breast Height Over Bark (DBHOB). Basal Area is the cross section of the tree trunk at breast height, and the sum for the stand or group of trees is expressed square feet per acre (after 1973 it was expressed in square metres per hectare). Lots of skinny trees, or a few fat ones, can have the same Basal Area, but when combined with the number of stems, Basal Area is a good indicator of stand density. Two common methods are used to measure of Basal Area – fixed area plots and angle count sampling. 1. Fixed area plots require setting out a small area, commonly 50 m x 20 m, and measuring all the trees at breast height, and doing some quick sums. 2. Angle count sampling involves a simple sweep of the forest from a fixed sampling point using a relascope, dendrometer sight, angle gauge, or glass wedge prism. This wooden builders ruler has been shaped at one end to create a shallow angle (usually less than 3 degrees). Standing in one spot, a sweep is made with the wedge held to the eye, and trees are counted as either “in” or “out”. The number of trees is multiplied by conversion factor of the wedge (10 in this case) to estimate basal area. It’s very quick and effective.Basal Area Angle Gauge The two ends fold up and one end (on the right) has been reduced in width to create a shallow angle for the viewer Home made by cutting down a wooden builder's ruler Many forestry students made their own Basal Area Angle Gauges and its thought this may be oneforest measurement, forests commission victoria (fcv)

The Forests Commission took safety very seriously, long before it became standard practice in the bush. The Chairman of the Commission, Alan Threader, personally chaired the safety committee Sandy Dobbin was appointed as the first "safety officer" in the early 1970s There were many innovations including safety boots and safety hardhats. Safety hardhats. One new hat with "two trees" FCV logo. One with hat with older style FCV sticker belonging to District Forester Col Almond (decorated with logos from the amalgamated CFL agencies).forests commission victoria (fcv), protective clothing

Linked to the 1983 Ash Wednesday BushfiresSmall metal lockable cash box with handle and tray insert This item was burnt in the 1983 Ash Wednesday bushfires which destroyed the FCV Office and nursery It was recovered from ashes of the building It was in the office safe and contained charred bank notes and a chequebushfire, forests commission victoria (fcv)

Y valves were used to split water supplies so it could be directed to a number of locations on a fire. In this case four outlets with two controlling valves. Canvas 1.5 inch hose was normally attached Screw connections rather than twist-camm locksY ValveYarrawonga Forests Commissionbushfire, fire pump, forests commission victoria (fcv)

Signs were erected around the forest to restrict the use of firearms.Shooting Prohibited sign - canvasbushfire, forest signs, forests commission victoria (fcv)

Before metrication was introduced into Australia in the 1970s land was measured in chains and links. Many old parish plans show length measurements in chains and links. Area was shown in acres, roods and perches. Gunter's chain was used for measuring distance in surveying. It was designed and introduced in 1620 by English clergyman and mathematician Edmund Gunter (1581–1626). Gunter developed the measuring chain of 100 links. The chain and the link, became statutory measures in England and subsequently the British Empire. After metrication units of length were measured in meters and area in hectares. The chain was later superseded by steel ribbon tape.The 66 foot long brass Gunter's Chain is divided into 100 links (each 7.92 inches long), and marked off into groups of 10 by shaped tags which simplify intermediate measurement. It was heavy but flexible enough to be dragged through the bush on surveying transects.(Hence the common forestry term "chainman). The chain was a precision part of a surveyor's equipment. It required frequent calibration, yet needed to be sturdy enough to be dragged through rough terrain for years. It has brass hand grips at each end of chain. 1 chain = 100 links = 22 yards = 66 feet = 792 inches. 10 chains = furlong 80 chains = 1 mile 1 acre = 10 square chains = 4 roods (1/4 acre) = 40 perches.forest measurement, surveying, forests commission victoria (fcv)

The origins of the humble handheld driptorch have been lost in time. They are widely used for ignition in controlled burning operations in forest and grasslands. This "home made" burner wand uses kerosene and dates from the 1950s. It has an unusual long handle with a bend and wick one one end.Unusual "home made" design Long handle burning wand with a wick at one end. Brass flow valve in the middle. Base attached to a container of kerosene and has a screw cap. bushfire, forests commission victoria (fcv)

Bushfire awareness gallows signs were common features during the summer fire season and hung outside both FCV offices and on major roadways This large metal sign has different text on each side and the text and lettering is simple enough to be read from a moving vehicleBushfire Awareness - gallows signbushfire, forest signs, forests commission victoria (fcv)

Method of carrying rolled up canvas fire hose. Canvas hose needs to be washed, dried, rolled and stored properly after it has been used otherwise it will rot. Unrolled hose is notorious for becoming tangled. Canvas fire hose and roll carrier. The wire handle separates in the middle to release the hose rollbushfire, forests commission victoria (fcv), fire pump

Motorola introduced the Bag Phone in 1988. These phones offered more durability and higher power output (up to 3 watts) than more conventional mobile phones of the time. Bag Phones were expensive to purchase and operate. They became available within the Department in the early 1990s but their use was very restricted to staff like fire communications duty officers. Senior regional managers also had bag phones. Bag Phones were also bulky and heavy and were often known as "The Brick". The 12 volt sealed lead-acid rechargeable battery provided up to 2.5 hours of talk time and 48 hours of standby time. They were replaced from the mid 1990s by smaller, analogue flip-phones with lighter Nicad batteries manufactured by companies like Nokia. The mobile phone network was patchy in country Victoria where two main telecommunications companies operated - Telstra and Optus.Motorola Bag Phone with handsetOptus 018 594 510 No battery Includes handset, aerial and 12 volt car-charger jack in vinyl bagforests commission victoria (fcv), communications

In the late 1970s, the must-have gadget in every forest office could be best characterised by the fax machine. Millions of people bought them because they represented a miracle. With a fax machine, you could send a sheet of paper to someone, anywhere in the country, or anywhere in the world, complete with a signature, in seconds. E-mail really didn't exist yet (except in military and university environments), so the fax machine was simply amazing. During the "golden age" of the fax machine, people faxed everything. Office lunch orders went to the local Chinese takeaway by fax rather than being phoned in, while fire maps, timesheets and other urgent documents, could all be sent out straight away. Nearly every legal document got faxed once it was signed. People also traded recipes, jokes, funny pictures and personal letters by fax rather than sending them in the snail mail. With the early machines, the output was printed onto a roll of thermal paper that regularly spewed out coils onto the floor if you weren’t watching. All this technology quickly faded, only to be superceded by the pervasive e-mail in the 1990s. But the humble fax machine gave us an early glimpse of what the office of the future would be like.Facsimile machinePitney Bowes 8050communications, forests commission victoria (fcv)

Not much is known about this particular machine and where it was usedEarly fax machine. In two parts. Mufaxcommunications, forests commission victoria (fcv)

Black powder splitting guns were commonly used to split large logs into more manageable pieces before the advent of excavators and front-end loaders in bush logging operations. A typical splitting gun used in Victorian forests was a piece of high-grade steel about 1-1/2 to 2 inches in diameter and about 16 inches long, and slightly tapered at one end. They had a ¾ inch hole drilled about 9 inches deep into the centre of the shaft with a small pilot hole drilled from the outside to load the fuse. The tube was carefully loaded with an amount of black gunpowder using a funnel and spoon. Experience being the guide on how much powder to use, which depended on log size, species and difficulty of splitting the wood. The hole was stopped with a piece of wadded paper and the gun positioned at the end of a length of the log to be split. The splitting gun was then belted into the log with a large wooden maul or even the back of an axe to a depth of about 3 to 4 inches. There were often markings as a guide. This also had the effect of tamping the black powder inside the gun. Preferably the gun was backed up by another large log to absorb the recoil shock and avoid it flying off in the bush somewhere. I have seen guns where a length of string and coloured flag could be attached to help find them. A length of fuse was then inserted in the small hole and lit. Kaboom !!!! Needless to say, the splitting gun was a dangerous implement.Log Splitting gun (large 50cm)forests commission victoria (fcv), hand tools

Black powder splitting guns were commonly used to split large logs into more manageable pieces before the advent of excavators and front-end loaders in bush logging operations. A typical splitting gun used in Victorian forests was a piece of high-grade steel about 1-1/2 to 2 inches in diameter and about 16 inches long, and slightly tapered at one end. They had a ¾ inch hole drilled about 9 inches deep into the centre of the shaft with a small pilot hole drilled from the outside to load the fuse. The tube was carefully loaded with an amount of black gunpowder using a funnel and spoon. Experience being the guide on how much powder to use, which depended on log size, species and difficulty of splitting the wood. The hole was stopped with a piece of wadded paper and the gun positioned at the end of a length of the log to be split. The splitting gun was then belted into the log with a large wooden maul or even the back of an axe to a depth of about 3 to 4 inches. There were often markings as a guide. This also had the effect of tamping the black powder inside the gun. Preferably the gun was backed up by another large log to absorb the recoil shock and avoid it flying off in the bush somewhere. I have seen guns where a length of string and coloured flag could be attached to help find them. A length of fuse was then inserted in the small hole and lit. Kaboom !!!! Needless to say, the splitting gun was a dangerous implement.Log Splitting gun (large 45cm)forests commission victoria (fcv), hand tools

Bushfire perimeter rather than bushfire area is the main control problem for firefighters on the ground. A conundrum rapidly compounded by spot fires. A small 5 ha fire can be nearly 1 km around the perimeter. That's a long way to build a control line by hand in rough bush. Dry firefighting techniques by hand were mostly confined to “knocking down” or “beating out” the flames, as well as "digging out". Digging or raking a “mineral earth” trail down to bare dirt proved most effective in forest fuels which, unlike grass, tend to retain heat and smoulder. Early tools were whatever happened to be close at hand. They were simple and primitive and included shovels, slashers, axes, hoes, beaters and rakes. A cut branch to beat the flames was often the only thing available. Farming and logging tools, developed over centuries of manual labour, and readily available at local hardware stores came into use, but little thought was given to size, weight, and balance. For years foresters experimented with combination tools. In about 1952 fire beaters and other implements were being replaced with Rakuts. However, its believed the now common Rakehoe is an Australian variation of the American McLeod Tool which was developed in 1905 by forest ranger Malcolm McLeod of the Sierra National Forest. The late Athol Hodgson advised that predecessors, Reg Torbet who had been the Chief Fire Officer for the Forests Commission from 1948-1956, along with his QLD counterpart Clive Price, went in late 1951 as Australian delegates on a 10 week fire study tour of Nth America organised by the United Nations. They came back with a couple of McLeod tools from Canada. Cam MacLeod (different spelling) had been the Head of Fire Research for the Canadian Forest Service at the time and had supplied them. The tools were ideal for deciduous forests in the eastern provinces and Clive arranged to have them manufactured in QLD. The Rakho, as it was then spelled, was first issued to FCV crews 65 years ago in 1955-56. The American Pulaski had been trialled, but never found favour with Australian firefighters.Rakhoeforests commission victoria (fcv), hand tools, forest harvesting, bushfire

Metal branding hammers were the most common way to control the sale and movement of hardwood timber produce like logs, railway sleepers, fence posts, and poles from Victorian State forests. Royalty was also paid on this basis. Hammers most commonly had a crown stamp on one end with a unique number in the middle which identified its owner, and a crows foot or broad arrow on the other. The broad arrow was a symbol traditionally used in Britain and its colonies to mark government property. Other local configurations were used by sawmillers, post cutters and pulpwood contactors. Forest regulations state that an authorised officer may use the crown mark to identify produce which has been sold and may be removed from the forest, whereas the broad arrow can be used to brand and mark trees which are not to be felled, or to indicate forest produce which has been seized. Hammers were traditionally only ever issued to forest officers and were an important, and closely guarded tool-of-trade. They were not transferred between staff and lending hammers was not permitted. But it was an onerous task for staff to hammer and tally hundreds of logs, or thousands of fence posts each week, so in about 1990 a system was introduced whereby hammers were allocated to logging contractors to grade logs and tally them instead. But there was still spot checking by authorised officers. A register was kept, and contractors paid a substantial deposit to make sure they didn't lose them, but they occasionally turn up by fossickers with metal detectors. While branding hammers are still used in some smaller locations, plastic tags and barcodes are now more common.Log Grading hammersforests commission victoria (fcv), hand tools, forest harvesting

Metal Pinch Barforests commission victoria (fcv), hand tools

Offset C Hookforests commission victoria (fcv), hand tools

Used to warn traffic of hazardsBattery operated traffic warning light - greenforests commission victoria (fcv), safety equipment

Used to warn traffic of hazardsMetal kerosene traffic warning light - red (CRB type)forests commission victoria (fcv), safety equipment

Different lettering guides were used depending on the scale of maps Cartographic guidance was provided by the FCV’s 1947 publication - “Handbook of Conventional Signs and Symbols for Use in Forest MappingPlastic lettering guides for use with ink Rotring pensRotring Scale and lettering sizes 5mmforests commission victoria (fcv), mapping, surveying

Used with Rotring ink pens of pencils to draw smooth shapes on mapsPlastic shapes used for mappingRotringforests commission victoria (fcv), mapping, surveying

Bushfire perimeter rather than bushfire area is the main control problem for firefighters on the ground. A conundrum rapidly compounded by spot fires. A small 5 ha fire can be nearly 1 km around the perimeter. That's a long way to build a control line by hand in rough bush. Dry firefighting techniques by hand were mostly confined to “knocking down” or “beating out” the flames, as well as "digging out". Digging or raking a “mineral earth” trail down to bare dirt proved most effective in forest fuels which, unlike grass, tend to retain heat and smoulder. Early tools were whatever happened to be close at hand. They were simple and primitive and included shovels, slashers, axes, hoes, beaters and rakes. A cut branch to beat the flames was often the only thing available. Farming and logging tools, developed over centuries of manual labour, and readily available at local hardware stores came into use, but little thought was given to size, weight, and balance. For years foresters experimented with combination tools. In about 1952 fire beaters and other implements were being replaced with Rakuts. However, its believed the now common Rakehoe is an Australian variation of the American McLeod Tool which was developed in 1905 by forest ranger Malcolm McLeod of the Sierra National Forest. The late Athol Hodgson advised that predecessors, Reg Torbet who had been the Chief Fire Officer for the Forests Commission from 1948-1956, along with his QLD counterpart Clive Price, went in late 1951 as Australian delegates on a 10 week fire study tour of Nth America organised by the United Nations. They came back with a couple of McLeod tools from Canada. Cam MacLeod (different spelling) had been the Head of Fire Research for the Canadian Forest Service at the time and had supplied them. The tools were ideal for deciduous forests in the eastern provinces and Clive arranged to have them manufactured in QLD. The Rakho, as it was then spelled, was first issued to FCV crews 65 years ago in 1955-56. The American Pulaski had been trialled, but never found favour with Australian firefighters.Fire Beater (canvas) 1930s designforests commission victoria (fcv), hand tools, forest harvesting, bushfire

Chainsaw fuel and oil carry containersforests commission victoria (fcv), bushfire, hand tools

Used to hammer into a saw cut when falling treesThree types of cutting wedges used when falling treesforests commission victoria (fcv), forest harvesting, hand tools

The FCV used green flashing lights rather than redPortable 12 volt flashing light for use on fire tankersforests commission victoria (fcv), bushfire, safety equipment

Used to protect ankles from sticks in thick scrub as well as from snake bitesCanvas protective gaiters with leather straps (ex-army)forests commission victoria (fcv), protective clothing, bushfire