View is looking northwest from the hillside just north of Allendale Road. The long rectangular house in the upper left is No. 22 Challenger Street, Diamond Creek, right at the sharp turn into Price Court. On the track in the straight section heading northwest are two small bridges where the track crosses the Diamond Creek, each fitted with derailment guard rails to prevent severe derailments should a train come off the tracks whilst crossing the culverts. Digital TIFF file Scan of 35mm Ilford FP4 black and white transparency471m, allendale road, challenger street, derailment guard rail, diamond creek, hurstbridge line, price court, red rattler, red rattler single carriage, single motor carriage, tait train

Large Gangers Trolly Turntable Many trollys were too heavy to physically lift off the track, so a turntable was needed. A railway gangers trolly was required to be "off tracked" at its working location, so that it would be clear for trains to operate. A special track at right angles to the running line was usually provided. When all the work was completed and after all the trains had cleared, the trolly was then "on tracked" so that it could proceed to its next location. These turntables were also in use at the Works Depot location. They were provided at designated locations, and in some cases the trolly carried a turntable on board. To allow for more than one trolly to be taken off the line, a longer version was available for use. The turntable would be placed on the rails and the trolly driven onto it. The turntable would then be rotated 90 degrees by human power and the trolly pushed off on to a prepared set of rails on the side of the line. The turntable would then be removed from the track allowing trains to run through that section. The gang could then get on with the work required near that location.Historic - Railway Permanent Way and Works - track equipment - Ganger's Trolley TurntableLarge Gangers Trolly Turntable made of wood with wrought iron fittingspuffing billy, gangers trolley turntable, trolly, trolley

Black and white photographs of the construction of the junction at Gertrude and Nicholson St c1955. On the right hand side of the photograph are two buses showing the Destination of Northcote. The former cable tram track in Nicholson St is yet to be removed - shows the offset between the tracks and the wood blocks. Possibly only the junction tracks have been completed at this time as there appears to be an excavation and a hut in the distance. There is a detour sign indicating that possibly vehicles used the completed section and that trackwork was underway for Gertrude St. The overhead has been erected. In the background is Osborne House. signs for The Age, The Sun and Peters Ice Cream. Early 1955?trams, tramways, trackwork, rails, track materials, track repairs, sleepers, equipment, cable trams, gertrude st, nicholson st, overhead

Methodist services began in late 1893 in the bush, near the end of the present Silvan Reservoir. The seats were split rails and the pulpit a fallen log with a sapling rail. Then a miner's bark hut became available in on the Recreation Ground. The Methodist Church was built and opened in 1903 on the corner of Moxham's Rd and David Hill Rd., with the financial assistance of Mr. James Griffiths of Griffiths Tea. This booklet gives a comprehensive history of the development of the church, its congregations and ministers.Soft cover booklet of 40 pages. Cream coloured cover with a photo of Monbulk Methodist Church 1972.monbulk methodist church, betty hotchin

This wooden cash ball came from the retail business of Cramond and Dickson. It was part of the mechanism for sending money and change to and from the customer to a shop assistant dealing with the finances. The ball ran along sloping rails in the shop. John Cramond and James Dickson, both from Scotland, established a general store in Warrnambool in 1855 in Timor Street. The business was later transferred to the corner of Liebig and Timor Streets and became a well-known landmark in Warrnambool, closing in 1973. This item is significant as it came from one of the most important businesses in Warrnambool’s retail history – that of Cramond and Dickson. It also is an important example of retail store practice in the late 19th century and early 20th century. This is a cylindrical wooden ball which separates into two parts to allow the insertion of money in the middle. There is a round metal disc which is housed in the centre of the wooden ball.It has a circle marked on the outer surface of both semi circles of the ball. It is brown in colour. On both halves of the ball on the outside – ‘D 4’cramond and dickson, warrnambool, money ball

Sepia photograph of workers employed ' on making the Bendigo Railway'. Workmen seated on rails with small girl. Group of men standing and seated in front of corrugated iron shed with Union Jack flag on pole. Adult females back left of photo. Hills with trees in background. Inscriptions: on back - handwritten in pen 'Employees in the making of the Bendigo Railway'. Top front R corner 'GP85'. On back - handwritten in ball point pen 'Presented to the Bendigo Historical Society by Stevenson McGilchrist, great grandson of the late William Robertson of 'Woding' Estate near Gisborne'. History: Prev. Acc. No. GP85person, group, male group of workers

Has strong association with the event of laying the track across Wendouree Parade during Nov. 1975, an essential task to enable the re-opening of the tramway by the BTPS.Bromide of a black and white photograph of rails being laid to cross Wendouree Parade to access the new BTPS depot access track. Excavation done, first main curve rail being positioned using a crane. Date of photograph late November 1974. Depot Junction in background. BTPS Annual report states that site work began 22/11/1974. Photographer unknown. Bromide made c1994 for possible publication, but not used. See also Reg item 3506.1 and .2 for other photos on the same day. See 1974 - 1975 BTPS Annual Report page 4.trams, tramways, btps, wendouree parade, track laying, depot junction

Newspaper clipping contained within Reg. Item 2526, page 10, titled "From Horse Tram to Trolly Bus" (mis-spelt word) recording the history of the cable trams in Melbourne, the formation of the company, prohibition of steam locomotives, costs, mechanical problems, Council objections, rails, visit of Mr. Hallide, court actions, King St. track, take over by the MMTB and that "conversion war still rages" - and perhaps trolley buses. Has been cut out from a sheet and pasted into the book. Written prior to final conversion in Melbourne in 1940. Note Item Not formally Numbered.melbourne, cable trams, tramways

Yields information about the early use of the Ballarat horse trams and condition of the roadway - lots of rocks on the road surface. Also shows an all male loading of passengers.Black and White copy photograph of a State Library of South Australia SLSA B34585 of an well loaded, only male passengers on a Ballaarat Horse Tram - Grenville and Sturt St. Two horse with many men, Wilson's Bucks Head Hotel in background. Condition of the road surface very rough - can't see the rails. Photo taken in early days, as no modesty boards on upper deck - say 1887. Possibly a trial trip. Collected by Alan Bradley from the State Library of South Australia early 1980's. Used in The Golden City and its Tramways - page 28.tramways, trams, sturt st, grenville st, bucks head hotel, horse tram

Has strong association with the event of laying the track across Wendouree Parade during Nov. 1975, an essential task to enable the re-opening of the tramway by the BTPS.Black and white photograph of rails being laid to cross Wendouree Parade to access the new BTPS depot access track. Excavation done. Date of photographs late November 1974. Depot Junction in background. BTPS Annual report states that site work began 22/11/1974. Has date stamp of "8.1.75" on rear of photograph. .1 - prior to first main curve rail being positioned using a crane. .2 - after first curved rail laid - see also Reg Item 1633. See also Reg Item 1633 for another photograph on the same day.tramways, trams, btps, wendouree parade, track laying, depot junction

Yields information the appearance of the SEC tramcar No. 23, which was often decorated in 1949 and the streetscape.Digital image from the Wal Jack Ballarat Album of trams No. 23 in Sturt St climbing the hill enroute to Gardens. Shows how the barrier rails were arranged. In front of the tram area a number of angle parked cars. In the rear are Patersons Furniture, Taylor and Taylor Chemists, Ballarat Fish Supply, Ritzy Cafe and Grill Rooms and a book store. The tram itself is looking shabby. Photo taken 20-3-1949. See image i2 for rear of photograph. See image i3 for hi res scan of print. See image i4 for hi res scan of negativeon rear of photo in ink, "SEC Ballarat, No. 23, in Sturt St, Ballarat 20-3-1949" and in top right hand corner Wal Jack copyright stamp with number "T99" written.trams, tramways, sturt st, city loop, tram 23

Red covered auction catalogue for a sale held on the 26th February, 1936 by Order of The State Rivers and Water Supply Commission at Clyde and the Main Depot at Narre Warren. For sale was Dredging,Mining and Contractors' Machinery, Plant and Equipment, Steam Winches, Boilers, Rails, Roadmaking & Farmers' Implements, Scrap Iron, Rolling Stock, Harness and Sundries. Columns to write prices on the right side edge of the pages. Hand written Supplementary List for Narre Warren Depot machine sewn inside the back cover. J. H. Curnow & Son were the auctioneers and the catalogue was printed by Boltons Print, Bendigo.business, auctioneers, j h curnow & son pty ltd, ian dyett collection - auction catalogue - the state rivers and water supply commission, j h curnow & son, boltons print bendigo

Postcard - full colour, Divided back type of Swanston St looking North just before the Flinders St intersection, with Young and Jackson Hotel and many neon signs in the background. Tram 756 with destination of Moreland and Route 15 is in the view. Note the wood planks in between the rails at the stop, possibly at the time that the bridge over the rail lines was being rebuilt. Appears to have a The Met tram stop sign on the safety zone. Possibly late 1980's. Nu-Color-Vue postcard with serrated edges, number ML 116 with logos and place for stamps and address.trams, tramways, swanston st, flinders st, moreland, route 15, tram 756

In 1902 a ballast siding was opened 4km south of Gellibrand to provide materials for track construction. A spur siding, with points facing Beech Forest and a capacity for six trucks, was cut into the side of a slope. Above this was erected a loading bin and chute. The stone proved to be of durable quality so the siding continued in commission after 1902 for track re-ballasting work. By the mid-1920s Victorian Railways found it more economic to use ballast from Penshurst, so the siding was closed by 1925 and the rails lifted.Photograph; B/W. Gellibrand Ballast Loading Sitegellibrand; ballast; railways; siding;

Provides a detailed list, not fully comprehensive, of purchase contracts for the MMTB between 1919 and 1969. Lists Buildings Cable wire ropes Cable grip dies General - punch card systems, advertising on trams Miscellaneous Vehicles Motor buses and Garage equipment Permanent Way Equipment Poles - steel and wooden Rail bonds Special trackwork Substation Equipment Traffic - ticket issuing machines and radio equipment Trams and bodies Tram equipment Tram rails Trolley Wire Workshops EquipmentYields information about MMTB Purchases between 1919 and 1969 - not complete.Document - 50 Foolscap sheets - photocopied.mmtb, tramways, contracts, purchases, workshops, trams, buses, trackwork, buildings, depots

Parking bay for viewing the Entrance situated on a sharp bend of the Princes Highway. Also in image part of Bullock Island and New Works area. Three motor cars in picture, post and rail safety fence Lakes Entrance Victoria. Also three colour postcards of same view showing progress at parking bay to steel mesh fence and steel guard rails numbers 04206.1, size 9 x 14 cm, 04206.2, 04206.3 size 10 x 14.5 cmColour postcard showing parking bay for viewing the Entrance situated on a sharp bend of the Princes Highway. Also in image part of Bullock Island and New Works area. Three motor cars in picture, post and rail safety fence Lakes Entrance Victoriacivil engineering, islands, waterways, gippsland lakes, vehicles

Photograph looks southward along St Kilda Rd from its intersection with City Rd and Alexander Pde, but trees obscure the view towards the Shrine of Remembrance, which may still be under construction (1927-34). Tram rails and overhead can be seen turning from St Kilda Rd into City Rd and several W2 class trams and a half cab bus can be seen. Two policeman in white helmets stand in the intersection controlling traffic.Yields information about early electric trams on St Kilda Rd Black and white print with no note.w2 class, half cab bus, st kilda rd, city rd, alexander ave, shrine of remembrance, rails and overhead, white helmet

Forty Eight page, side staple book within blue Rexene covers. Titled "Melbourne and Metropolitan Tramways /Electric System /Instructions to Drivers in Electric Car Operation" Dated 1966. Printed by Regent Press Pty Ltd, 457 Plenty Road, Preston. Provides in a Q & A format, instructions to drivers in electric car operation, photos of various types of controllers, an A.B.C. for tramways drivers - "always" points to remember and has a reference index. Copy 1 - has telephone numbers of Training School and specific pointers re Regulations 106 and 107 and some of the Q&A have been circled in blue. This copy was imaged. The May 1974 instructions of "Tram car Braking on Greasy Rails", has adhesive tape remnants. Copy 2 - 1/5/1975 instructions loose inside the book. Copy 3 - added 29/5/2014 from the collection of R. Wearne. Copy 4 - added 15-6-2015 - from Ron Scholten donation of 11-4-2015. Copy 5 - added 14-12-2015 from donation of Norm Cross 11-10-2009. Had the instructions for Tram car braking on Greasy Rails appended inside front cover - loose, with adhesive tape remnants. Relocated to Reg Item 2913.copy 3 has 7 numbers in ink inside the front cover, a number of questions in the book have been circled., copy 4 - has numerous changes to issue on page 1, ink crosses on specific questions., copy 5 - has "K.T. Hall Works Manager" in ink on inside of front cover, and notes on pages 15, 16, 17, 19, regarding the use of the motor cut out switches.trams, tramways, mmtb, drivers, training, instructions, motormen

Series of 3 black and white photographs of:- .1 - construction of the trackwork for the new Maribyrnong River Bridge, has the temporary track on the left hand side of the photograph. Has the Express Freight Transport building in the background. .2 - as above, appears that the track on the northern side is almost completed. An Inspector is standing watching the work. This work was completed mid 1967. .3 - construction of trackwork possibly the curve from Gordon St to run alongside now River St. This work was undertaken during 1954.Some photos have pencil marks on rear.trams, tramways, trackwork, rails, track materials, track repairs, sleepers, equipment, maribyrnong river bridge, bridges, gordon st, river st, footscray

Rail Bender - Part of Hydraulic Rail Bender Rail Bender – No. 3 Most rails are produced straight. While they to easily bend and appear flexible, they are required to bend for some curves, at rail joins on curves and at point (turn-out) junctions. For a safe transition around curves and in the finer areas of the point, this use to be done with a manual rail bender. Sometimes referred to as a Buddah, the rail bender attaches its two claws to the rail. In the middle of the two claws is a screw that is tightened slowly using large spanner. Historic - Railways Permanent Way and Works - track equipment - Rail Bender large Rail Bender - Part of Hydraulic Rail Bender made of cast wrought iron puffing billy, rail bender

Hand Rail Drill Out on the track in the old days, it was sometimes required to drill some holes in a piece of rail so that two rails may be joined together by a metal joiner – called a fishplate. Before the use of generators and oxy cutting, the only way to do this was with a hand drill. This is the machine operated by two people, that would drill a hole in the rail. With two to three holes to be drilled in each rail end (ie 4 or 6 holes), it was a tiring, back breaking job. And then there was usually the rail on the other side of the track to be done! Historic - Railways Permanent Way and Works - track equipment - Hand Rail DrillHand Rail Drill made of metal puffing billy, hand rail drill

The article and photo report on the poor condition of roads in particular Hayden's Road and the former, short lived Victorian Railways Beaumaris - Black Rock tram line. Has two photos showing the road condition. The second photo shows sleepers from the former tram line and a badly worn road surface that had been placed on top. The item by a staff reporter likens the road to wartime battle fields. The tram line rails were lifted or removed during 1939 - see page 35 of The Brighton Electric Line.Yields information about the road condition in the Beaumaris area in 1955.Newspaper clipping titled - "Seaside tracks are "roads"" - Melbourne Herald 12/11/1955"Melb "Herald" Sat 12 Nov 1955"trams, tramways, vr trams, track maintenance, tram tracks, beaumaris

Five photographs of Menzies Creek and other villages during the August 2020 Covid Lockdown, taken by Kate Leigh. 027/37 is a photograph of a drinking tap in a park, with a sign saying “Drinking taps closed until further notice”. 027/38 is a cafe sign instructing customers “Please order inside only 3 customers @ a time inside. Wait outside for your order. Thx for your patience.” 027/039 is a shop with a corrugated iron roof, closed off with tape. 027/40 and 027/41 both feature close-ups of railway tracks, with the latter showing weeds sprouting from rails.

Yields information about the formal opening of the tram services to be operated by the BTPS in 1975 and who was involved.Newspaper Clipping of Thurs. Jan 23, 1975 giving news of the formal opening of the BTPS tram service on 1/2/1975 by the General Manager of the SECV, Mr. J.C.Trethowan. Has a photo of the depot with the trolley on No. 1 road, 27 on 2 road, and 28? on three road and depot fan with rails well above the ground level. Newspaper Clipping notes trial running in Wendouree Parade, history of the BTPS, work undertaken, and number of members. Second copy of cutting glued onto a sheet of foolscap plain paper added 5/7/2017 and image revised. From donation of Ruth Nelson.trams, tramways, btps, tramway opening, museum, opening

Negatives No. N334 and 335 and black and white prints made by a laser printer (stored in folder ) of fitters, overhead crews lining up the overhead at the Russell St. crossover in Bourke St. Has W6 988 in the photo, along with tower wagons 2 and 8. 1606.2 shows device laid between rails that allows the location of the overhead to be checked, relative the to the centre line of the track. Photo taken 19/6/1955. Dave Macartney 12/1/2001 identified Doug Lees in black coat and hat looking at instrument. Doug was an Engineer with the MMTB. Negative scanned hi res and imaged updated 22/5/2020.trams, tramways, melbourne, bourke st, russell st., testing overhead, commissioning, tram w6 988

Digital image - four pages - of a report to the Melbourne Tramways Trust, preliminary report looking at the condition of the tramway track - rails, wood blocks prior to the take over of the Tramway by the Trust (1916). Prepared by T Hamilton Engineer and Secretary, dated 10/3/1913 assisted by Gerard Wight of Melbourne Uni. Looks at each line, rail wear, opening dates, rail weight, and condition of blocks. Also looks at the covenants or conditions of lease for the track and tramway, Completes report with notes about repairs, maintenance and renewals and legal advice of Sir John Madden. See item 9151 for an original copy.trams, tramways, melbourne, cable trams, track, trackwork, reports

.1 - Pamphlet - four fold - DL side four colour printed on off-white paper, titled "Tram service changes St Kilda Rd & Toorak Rd", advising intending passengers of the work between 1/7/2017 and 11/7/2017 to connect route 8 at Toorak Road West into St Kilda road the closure of the route via Park and Domain Road. Has a map, list of service changes, bus replacement guides and contact information. Has the logos of Metro Tunnel, Yarra Trams and PTV. .2 Pamphlet, printed and cut for use in trams around passenger hanging rails, titled "St Kilda Rd Tram and Bus service changes - Saturday 1 to Tuesday 11 July" - details bus replacement services and tram stops. Related to the main pamphlet - see image Set of five digital images taken at stop 25, Park St advising of the route diversion, replacement services and stop closure and two protest posters on fences nearby the stop about the Metro Tunnel project trucks using the local streets and the closure of the Park St / Domain Road tram line. .2 Pamphlet, printed and cut for use in trams around passenger hanging rails, titled "St Kilda Rd Tram and Bus service changes - Saturday 1 to Tuesday 11 July" - details bus replacement services and tram stops. Related to the main pamphlet.trams, tramways, park st, domain junction, metro tunnel, toorak rd, st kilda rd, tramway construction

THE ECHUCA COALING STAGE. Locomotives would stop alongside to receive coal dropped into their tenders from small overhead rail mounted tipping trays. Water could be obtained from either the elevated tank at one end or the connected standpipe at the opposite end. Locomotive firebox contents could be dumped into pits between the rails from locomotives once they were carefully positioned above them. Such locomotives then could move onto the Engine Shed area for overnight parking. Firebox fires would be re-lit when the locomotive was next needed in a day or so.Digital TIFF file Scan of 35mm Ilford FP3 black and white negative transparencygeorge coop collection, echuca railway station, k-185, k-class steam locomotive (vr newport workshops), railway workshop

THE ECHUCA COALING STAGE. Locomotives would stop alongside to receive coal dropped into their tenders from small overhead rail mounted tipping trays. Water could be obtained from either the elevated tank at one end or the connected standpipe at the opposite end. Locomotive firebox contents could be dumped into pits between the rails from locomotives once they were carefully positioned above them. Such locomotives then could move onto the Engine Shed area for overnight parking. Firebox fires would be re-lit when the locomotive was next needed in a day or so.Digital TIFF file Scan of 35mm Ilford FP3 black and white negative transparencycoal hopper, echuca railway station, george coop collection, k-158, k-class steam locomotive (vr newport workshops)