Decimal currency was spectacularly introduced in an overnight overthrow on 14 February 1966, but it took another 8 years before metrication finally arrived in the forest and timber industry. Eventually, the measurement of logs and sawn timber changed from imperial, and excruciating, measures such as super feet of sawn timber, billets and cunits (100 cubic feet) of stacked pulpwood and hoppus log volumes to simpler cubic metres. Measuring firewood was a particular nightmare. For example, there were standard chords, stove cords, kitchen cords, running cords, face cords, thrown chords, fencing cords, country cords, long cords, raummeter or steres (1m x 1m x 1m). A standard cord of firewood had a volume of 128 cubic feet, measured as a pile 8 feet long, 4 feet high and 4 feet wide (3.624 m3). And how about this for confusing…. in Victoria, an imperial or long ton (by measure) of green firewood was a stack 5 feet long billets (2 axelengths at 2′ 6″ each), one axelength high (2′ 6″) and two axelengths long (5 feet) equalling 62.5 cubic feet. For added befuddlement, there were three different sorts of tons: Imperial tons or long tons, American short tons and metric tonnes (spelled with two n’s). Not forgetting that a cubic imperial ton of firewood (40 cubic feet) which equalled 1.133 cubic metre. The metrication process began in 1974 and was completed by 1976 but the transition was not without its challenges along the supply chain for foresters, overseers, logging contractors, sawmillers, hardware stores and builders alike. Timber lengths changed from feet to metres but were still sold in multiples of one foot or 0.3 m (1.8, 2.1, 2.4, 2.7 etc) whereas a menacing lump of 4-Bee-2 transformed into a rather less colourful 100mm by 50mm. Measurement and calculations of area also became so much easier in hectares rather than complicated acres, roods and perches. The Forest Metriverter slide-rule was issued by the Forestry and Timber Bureau to make metric conversions easier.Forest MetriverterRoss Pennyforest measurement, surveying, forests commission victoria (fcv)

Dedicated phone lines were often connected between FCV District Offices and firetowers or local depots. These lines were activated by winding the metal handle to ring the bell at the other end of the line.Bakelite phone with handset and winder. Made of Bakelite.radios, forests commission victoria (fcv)

Bushfire behaviour is influenced by many factors including temperature, relative humidity (RH), forest type, fuel quantity and fuel dryness, topography and even slope. Wind has a dominant effect on the Rate of Spread (ROS), as well as fire size, shape and direction. Temperature and relative humidity have major impacts on fuel dryness and therefore upon the availability of fuel for combustion. The amount of fine fuel available can increase rapidly from nearly zero when fuel moisture content is more than 16% after rain or a heavy morning dew, to many tonnes per hectare as fuel dries out later in the day and the moisture content drops below 9%. This explosive escalation in the amount of available fuel can happen over a few hours on hot and windy days. A sling psychrometer is a simple device for determining air temperature and relative humidity. It contains two thermometers, one of which is covered with a wick saturated with ambient temperature liquid water. These two thermometers are called dry bulb and wet bulb. When the sling psychrometer is spun rapidly in the air, the evaporation of the water from the wick causes the wet bulb thermometer to read lower than the dry bulb thermometer. After the psychrometer has been spun long enough for the thermometers to reach equilibrium temperatures, the unit is stopped, and the two thermometers are quickly read. A psychrometric scale on the side of the instrument is then used to convert the dry bulb temperature TDB and the wet bulb temperature TWB into humidity information. The wet bulb temperature is approximately equal to the adiabatic saturation temperature. The thermometers fold back into the plastic handle when not in use. Used to measure temperature and relative humiditySling PsychrometerBACHARACH INSTRUMENTS - Pittsburg PAbushfire, forests commission victoria (fcv)

Used at fire basecampsWood fire used at basecamps Metal plates fold flat for transportforests commission victoria (fcv), bushfire, camping equipment

Base campView of base camp equipment at the Altona Museumforests commission victoria (fcv), camping equipment, bushfire

used at fire campsMetal food masherforests commission victoria (fcv), bushfire, camping equipment

Uniforms were not commonly worn by forest and fire staff. This uniform was tailor made for the Chief Fire Officer, Gary Morgan, in about 2000Chief Fire Officer uniform (jacket and tie) belonging to Gary Morganforests commission victoria (fcv), bushfire

The wooden mould was originally made in the early 1980s by one of the crew in his spare time in East Gippsland (Bairnsdale maybe). It was passed it on to Ian Long and then Barrie Marsden at Altona. It was not made for any particular purpose other than just a copy of the iconic FCV logo. It sat in the office at Altona for a little while until one day Barry thought it could be used to cast a solid replica. The wooden mould was taken to a foundry in North Melbourne and three bronze replicas were cast and polished. One was used when the Chief Fire Officer, Bary Johnson, was retiring More were cast in brass and the plaques became a standard presentation item for retiring FCV personnel. The wooden mould eventually cracked and can no longer be used. Hand madeWooden mould and presentation plaqueforests commission victoria (fcv), forest signs

Bushfire awareness gallows signs were common features during the summer fire season and hung outside both FCV offices and on major roadways These six large metal signs have different text on each side and the message and lettering is simple enough to be read from a moving vehicle Metal Fire awareness gallows signsforests commission victoria (fcv), bushfire, forest signs

Signs used to identify roles at bushfires These roles and titles were used prior to 1984 and the introduction of the AIIMS control system Signs used to identify people and roles as bushfire incidentsforests commission victoria (fcv), bushfire, forest signs

Thought to have come from the old Newport workshopsStandard issue Public Service wall clockforests commission victoria (fcv), forest signs

Used for measuring distances in the forest. Steel bands (out of tradition were called the chain) were created around 1890. They replaced the traditional Gunter chain. The band could be repaired by soldering slip-on joiners and than and recalibrating.Steel measuring band (50m) on plastic reel with winding handleFCV 281forests commission victoria (fcv), assessment, forest measurement, surveying, mapping

Used for measuring distances in the forest. Steel bands (out of tradition were called the chain) were created around 1890. They replaced the traditional Gunter chain. The band could be repaired by soldering slip-on joiners and than and recalibrating.Steel measuring band (50m) on plastic reel with winding handle missingFCV 188forests commission victoria (fcv), assessment, forest measurement, surveying, mapping

Used for measuring distances in the forest. Steel bands (out of tradition were called the chain) were created around 1890. They replaced the traditional Gunter chain. The band could be repaired by soldering slip-on joiners and than and recalibrating.Steel measuring band (1 chain - 66 feet) on metal reelFCV 075forests commission victoria (fcv), assessment, forest measurement, surveying, mapping

used for surveyingTelescope used for surveyingStanleyforests commission victoria (fcv), forest measurement, surveying

Lightning is one of the major causes of bushfires, particularly in the remote mountains. This lightning detector system was developed by Dr. Peter Kourtz at Canada’s forest fire research institute. By 1977, some 300 were in use across the country. The small mushroom antenna could detect short-range (20-mile) changes in electrostatic field associated with lightning strikes. It needed to be placed out in the open on a hilltop and away from nearby trees. It simply counted the number of "strikes". The detector doesn't seem to have a direction finding capability or be able to distinguish between cloud-to-cloud or cloud-to-ground lightning. It's not sure how this particular unit found its way to Victoria. The Bureau of Meteorology's (BOM) current lightning detector network uses radio waves emitted by lightning to pinpoint the location of lightning strikes. The network is operated by a private company that sends data to the BOM in real time. Lightning detection systems use sensors like antennas, GPS receivers, and processing systems to detect radio waves, also known as sferics. The systems calculate the lightning's location and speed by measuring how long it takes for the radio signal to reach the different antenna stations. The BOM also has a Thunderstorm Tracker that uses weather radar data to identify areas of potential thunderstorm activity. The tracker updates every six minutes and shows the direction thunderstorms are moving, as well as their expected position in 10, 20, and 30 minutesLightning detector 1970sQ-Techforests commission victoria (fcv), weather, bushfire, bushfire aviation

Bushfire behaviour is influenced by many factors including temperature, relative humidity (RH), forest type, fuel quantity and fuel dryness, topography and even slope. Wind has a dominant effect on the Rate of Spread (ROS), as well as fire size, shape and direction. Temperature and relative humidity have major impacts on fuel dryness and therefore upon the availability of fuel for combustion. The amount of fine fuel available can increase rapidly from nearly zero when fuel moisture content is more than 16% after rain or a heavy morning dew, to many tonnes per hectare as fuel dries out later in the day and the moisture content drops below 9%. This explosive escalation in the amount of available fuel can happen over a few hours on hot and windy days. This device is used for determining air temperature and relative humidity. It contains two thermometers, one of which is covered with a wick saturated with ambient temperature liquid water. These two thermometers are called dry bulb and wet bulb. Once the thermometers to reach equilibrium temperatures the two thermometers are quickly read. The figures are then used to convert the dry bulb temperature TDB and the wet bulb temperature TWB into humidity information. The wet bulb temperature is approximately equal to the adiabatic saturation temperature. Relative humidity meter in wooden box two stainless steel tubes contain wet and dry thermometers A small clock drives a fan motor in the base to circulate airforests commission victoria (fcv), weather, bushfire

Used for adding and inventory work The Speedie was a manual adding machine that could not perform subtraction. It consisted of eight columns and five rows of keys in both maroon and ivory. It had a nine digit display that could add up. It could perform multiplication by using repeat action. If you examine the keyboard you’ll note that it only shows numbers 1 through 5. If you want to use numbers 6 through 9 then what you do is hit two keys that add up to that number. Simple office adding machine Made from Bakelite Chadwick-Miller Inc (CMI) was a Boston based importer of low-cost gift items and stationery products sourced mostly from Japan. These products were branded as Chadwick-Miller although CMI was not a manufacturer. It is known that Chadwick-Miller was in business in 1960, although its founding year is unknown. The company dissolved in 2007.Speedie add-a-maticforests commission victoria (fcv), forest measurement

These lamps were used for military communications during World War 1 and also through to World War 2A portable, electric morse signalling lamp, used for daylight communications The lamp design was patented in 1916 by Oliver Lucas. This unit was manufactured in 1918 This signalling lamp used an external battery as a power source. An adjustable screen is provided (used with a coloured lens) for night time signalling Includes sight tube Lucas Birmingham 1918forests commission victoria (fcv), communications

Telescope mounted on tripodL McKenzieforests commission victoria (fcv), communications, surveying

Logs were sold to sawmillers from State forest from 1 July 1974 in cubic metres (true volume). Previously sawlogs had been sold on the basis of Hoppus volume. This simple device with two rotating wheels enabled staff in FCV offices to rapidly calculate log volumes from measurements taken in the bush of log girth and length and recorded on paper log dockets. From the early 1980s automated systems became available with the advent of cheap electronic office calculators and simple computers.An early manual device that was superseded by electronic calculatorsOffice Device Twin rollers used to quickly and simply calculate true log volumes using measurements of girth and length. An allowance could also be made for pipe defects. The top roller was for larger diameter logs.Imperial measurement of logs (pre 1976)forests commission victoria (fcv), forest harvesting, forest measurement

The heavy weight is pinned onto the map and the tracing arm is used to follow the boundary to be measured Reading the number of revolutions from the two the scale wheels the area in square inches could be measured. Knowing the scale of the mapsheet the figure was converted to areas or hectares Generally at least three measurements were taken to ensure accuracy and precisionPlanimeter used to measure areas from scale maps. Includes wooden box One revolution of the main wheel equaled 10 square inches. A smaller rotating scale on the side was used to subdivide the area.Benallaforests commission victoria (fcv), forest measurement, surveying

The heavy weight is pinned onto the map and the tracing arm is used to follow the boundary to be measured. Reading from the digital scale the area in square centimetres could be measured. Knowing the scale of the mapsheet the figure was converted to areas or hectares Generally at least three measurements were taken to ensure accuracy and precisionPlanimeter used to measure areas from scale maps. Kent Planitron UP103forests commission victoria (fcv), forest measurement, surveying

The rollers move over the map as the tracing arm is used to follow the boundary to be measured. The wheels allow unlimited horizontal travel and vertical travel within the limits of the arm movement. They measure in the X and Y directions Reading from the digital scale the area in square centimetres could be measured. Knowing the scale of the mapsheet the figure was converted to areas or hectares Generally at least three measurements were taken to ensure accuracy and precisionPlanimeter used to measure areas from scale maps. Includes box but no charger Plancom KP90forests commission victoria (fcv), forest measurement, surveying

used to measure distances on mapsAdjustable stainless steel mapping dividers with wooden boxforests commission victoria (fcv), forest measurement, surveying, mapping

Used to draw parallel lines on mapsHeavy metal ruler on brass rollers with a wooden boxforests commission victoria (fcv), surveying, mapping

Engineers level used to lay out construction sites, roads and contoursMetal dumpy with box level SCAforests commission victoria (fcv), surveying, mapping

The map wheel is a simple, fast and accurate way to measure distances on maps, whether in straight lines or along curves. Hold the device from the tip and trace with the small wheel at the bottom along the line to be measured Measures distances in miles, kilometres or nautical miles depending on the scale on the side.Two metal map measuring wheel sMap scales on each side of wheelforests commission victoria (fcv), surveying, mapping

Used to measure distance on scale mapsScale rulerW&G forests commission victoria (fcv), surveying, mapping

Used to sample fine fuels on the forest floor. The ring was pushed into the litter to sample 0.1m2Heavy metal ring with sharpened bottom edgeforests commission victoria (fcv), bushfire, forest measurement