Showing 478 items
matching different types
-
Melbourne Tram Museum
Drawing, Melbourne & Metropolitan Tramways Board (MMTB), "Plan showing types and sizes of overhead troughing in Depots", post 1964
Drawing - original dyeline print - folded into 16, showing dimensions and layout of the wooden troughing in 16 different sheds at the depot - e.g. old and new Malvern. Prepared July 1934. Drawing Number 06739A Revision A Feb. 1964trams, tramways, depot, overhead, trolley wire, trolley poles, electrical equipment -
Melbourne Tram Museum
Document - Instruction, Melbourne & Metropolitan Tramways Board (MMTB), "Westinghouse S6A and S6B Electric Compressor Governors", 1916
Set of two different books, but with the same content about the Westinghouse Traction Brake Company, pamphlet 2412, titled "Westinghouse S6A and S6B Electric Compressor Governors" (known as Beetle back Governors). Each book contains 4 typed sheets on instructions and the working of the governor and six photograph illustration sheets. .1 - has been copied possibly from .2 and bound into a manila folder with a large "W" and "Westinghouse Traction Brake" labels stapled to the right hand side. .2 - is an original Westinghouse document dated 1916. Document Re typed by the MMTB 1955..2 - has C. Hodgson Trams Sheds" on the inside of the front cover.trams, tramways, westinghouse, compressors, governors, tramcars, air compressors -
Ballarat Tramway Museum
Drawing, Victorian Railways, Ears for Tramway Overhead Construction, 1924
... of four different types of trolley wire fittings and how they were ...Gives the design details of the device or fitting known as a trolley wire ears that holds a tramway copper trolley wire in position. Notes that the drawing was traced in 1924 from a MMTB drawing. Has details for a splicing ear, straight line ear. feeder ear and curve ear along with details for nuts and screws.Yields information about the design of four different types of trolley wire fittings and how they were fabricated for use on the two tram lines, or electric street railways operated by the Victorian Railways.Dyeline print of Victorian Railways drawing number 4057 - Ears for Tramway Overhead ConstructionHas number "7513 D.33" in black pen in bottom right hand corner.tramways, trams, overhead, victorian railways, trolley wire, engineering, electrical engineering -
Melbourne Tram Museum
Postcard - Five panel Melbourne tram photographs, Nucolorvue Publishing, 1986
... 6115. Two copies held. Yields information about five different ...Postcard featuring five Melbourne tramcars - A1 253 (Mont Albert route 42), W6 963 (Moreland Route 15), Z1 61 (City Route 96), W6 990 (advertising tram for San Remo Oct. 1986) and SW5 816 - Transporting Art Leunig tram - Garden of Eden - 1986. Rear of tram provides a short note on the history of Melbourne trams, noting that cable trams commenced in 1885. Nu-Color-Vue number 12ML101, NCV 6115. Two copies held.Yields information about five different types of Melbourne trams in 1986.Postcard colour - Five panel Melbourne tram photographs - Nu-Color-Vuetrams, tramways, a1 class tram, w6 class tram, z1 class tram, w5 class tram, transporting art, michael leunig, tram 253, tram 963, tram 990, tram 61, tram 816 -
Melbourne Tram Museum
Postcard - Seven panel Melbourne tram photographs, Nucolorvue Publishing, Melbourne's Trams, 2001
... information about seven different types of Melbourne trams around 2001 ...Postcard featuring seven Melbourne tramcars - B2 2111 in an all-over advertising livery for Crown "World of Entertainment" in 2001, SW6 957 City Circle, B2 2070 (Bundoora), C1 2004, B2 2019 (2001) advertising Luna Park outside Luna Park, W7 1005 (Toorak Glenferrie Rd, route 8) and an SW6 tram as one of the Restaurant trams. Nu-Color-Vue number 11ML580, NCV 13584Yields information about seven different types of Melbourne trams around 2001.Postcard colour - seven panel Melbourne tram photographs - Nu-Color-Vuetrams, tramways, tramcar restaurant, luna park, w7 class tram, sw6 class tram, b class tram, c1 class tram, advertising trams, tram 2111, tram 957, tram 2020, tram 2004, tram 2019, tram 1005 -
Melbourne Tram Museum
Postcard - Four panel Melbourne tram photographs, Bartel Collectors World, 1993
... information about four different types of Melbourne trams around 1993 ...Postcard featuring four Melbourne tramcars - B2 2100 (Bundoora route 86), Z1 53 (St Kilda Junction, route 15), SW6 888 (City Circle), and SW6 965 advertising Australian Express 1993Yields information about four different types of Melbourne trams around 1993.Postcard colour - four panel Melbourne tram photographs - Barteltrams, tramways, tramcar restaurant, luna park, w7 class tram, sw6 class tram, b class tram, c1 class tram, advertising trams -
Melbourne Tram Museum
Ephemera - Metcard - Love your Trams, Metlink, 2007 - 2008
... and 2 - 21-6-2007 Demonstrates one of many different types ...One of many different designs or fronts of Metcards. This design was published for Yarra Trams with the message "Love your trams". 1 - 2 hour concession - used 20-3-2008 2 - Off-Peak daily, zones 1 and 2 - 21-6-2007Demonstrates one of many different types of Metcards issued during the period of used in Melbourne from 1996 to 2013Ticket - printed on light card with a magnetic stripe. Has the ticket number and contact details, Metcard and Metlink logo on the front of the card.trams, tramways, tickets, metcard, metlink, yarra trams, trams as icons -
Melbourne Tram Museum
Ephemera - Metcard - generic, Metlink, 2008-2010
... -08 to 2-2-09 Demonstrates one of many different types ...Set of five generic Metcards with the Metcard logo and transport Mode icons. Has the contact details and the Metlink logo on the front of the ticket. Items 1 to 4 have a statement promoting the use of Metcards and printed in blue face colour 1 - 2 hour concession - used 2-7-10 2 - first copy no details, 2nd copy 2-hour concession - 2-8-10 3 - unused 4 - 2 x 2 hour concession - used 7-2009 and 9-9-2010 5 - 2 x Value Metcard, printed with a purple face, barcodes on rear - used 10-08 to 12-08 and 2nd copy 4-12-08 to 2-2-09Demonstrates one of many different types of Metcards issued during the period of used in Melbourne from 1996 to 2013Set of five generic Metcard tickets - printed on light card with a magnetic stripe. Has the ticket number and contact details, Metcard and Metlink logo on the front of the card.trams, tramways, tickets, metcard, metlink -
Melbourne Tram Museum
Ephemera - Metcards - Festivals - set of 8, Metlink, 2005-2009
... -2008 Demonstrates one of many different types of Metcards ...Set of seven Metcards with the Metcard logo and transport Mode icons. Tickets used to promote Festivals. Two copies of each ticket held. 1 - 2009 - Jazz Festival - Daily Full Fare - 1-5-2009 and 2 hour Concession - 18-4-2009 2 - 2005 - Arts Festival - 2 hour full fare - 30-10-2005 and Daily Full Fare - 1-11-2005 3 - 2007 - Comedy Festival - 2 hour full fare - 14-4-2007 and Daily Full Fare - 10-4-2007 4 - 2009 - Comedy Festival - 2 hour concession - 18-3-2009 and 2 hour concession 5 - 2008 - Comedy Festival - 2 hour concession - 21-2-2008 and 21-2-2008 6 - 2007 - Melbourne International Arts Festival - 2 hour concession - 29-10-2007 and Daily full fare - 29-9-2007 7 - 2008 - Melbourne International Arts Festival - 2 hour concession - 30-9-2008 and 21-10-2008Demonstrates one of many different types of Metcards issued during the period of used in Melbourne from 1996 to 2013Set of seven Metcard tickets - printed on light card with a magnetic stripe. Has the ticket number and contact details, Metcard and Metlink logo on the front of the card.trams, tramways, tickets, metcard, metlink, festivals, jazz festival, melbourne events, comedy festival, arts festival -
Melbourne Tram Museum
Ephemera - Metcards - Events and festivals - set of 6, Metlink, 2007-2009
... different types of Metcards issued during the period of used ...Set of six Metcards with the Metcard logo and transport Mode icons. Tickets used to promote Festivals or events Two copies of each ticket held. 1 - 2008 - Circus OZ - Seniors Daily - 30-5-2008 and 2 hour full fare zone 1 - 27-5-2008 2 - 2009 - Circus OZ - 2 hour concessions - 27-5-2009 and 20-6-2009 3 - 2008 - Melbourne Writers Festival - Daily Concession - 17 and 19-9-2009 4 - 2009 - Melbourne Writers Festival - Full Fare - 3-9-2009 and 2 hour concession - 24-8-2009 5 - 2007 - Guggenheim Collection at the National Gallery - 2 hour concession - 21-8-2007 and 22-10-2007 6 - 2008 - The Medieval Imagination at the State Library - 2 hour concession - 11-4-2008 and 22-4-2008 Demonstrates one of many different types of Metcards issued during the period of used in Melbourne from 1996 to 2013Set of six Metcard tickets - printed on light card with a magnetic stripe. Has the ticket number and contact details, Metcard and Metlink logo on the front of the card.trams, tramways, tickets, metcard, metlink, festivals, melbourne events, circus oz, exhibitions -
Melbourne Tram Museum
Ephemera - Metcards - Promoting places - set of 2, Metlink, 2009
... -08-2009? Demonstrates one of many different types of Metcards ...Set of two Metcards with the Metcard logo and transport Mode icons. Tickets were used to promote well-known Melbourne locations or places. Two copies of each ticket held. 1 - 2009 - Shrine of Remembrance - 1934 - 2009 - both 2 hour concession - 23-11-2009 and 10-12-2009 2 - 2009 - Luna Park and celebrity Tony Leonard 3AW sports commentator - both have a bar code on the rear. Used for Daily Full fare, probably purchased in bulk from an agent - 05-08-2009? Demonstrates one of many different types of Metcards issued during the period of used in Melbourne from 1996 to 2013Set of two Metcard tickets - printed on light card with a magnetic stripe. Has the ticket number and contact details, Metcard and Metlink logo on the front of the card.trams, tramways, tickets, metcard, metlink, shrine of remembrance, luna park, tony leonard -
Melbourne Tram Museum
Ephemera - Metcards - fund raising - set of 6, Metlink, 2005 - 2009
... one of many different types of Metcards issued during ...Set of six Metcards with the Metcard logo and transport Mode icons. Tickets were used to promote fundraising for medical treatments Two copies of each ticket held except for item 6. 1 - 2005 - "Kids under cover" - building homes for children - Full Fare - August 2005 2 - 2007 - "Walk to cure Diabetes" - Off peak daily - 13-9-2007 and 2 hour concession - 4-10-2007 3 - 2008 - "Peter Mac connexforcancerday" - sponsored by connex - Daily concession - 14-7-2008 and 2 hour concession - 3 -7-2008 4 - 2009 - "Peter Mac connexforcancerday" - sponsored by connex - Daily concession - 12-8-2009 and 2 hour concession - 5-8-2009 5 - 2007 - "Help save a dad's life" - sponsored by Bunnings for Alfred Intensive Care unit - Off Peak Daily - 26-9-2007 and 17-9-2007 6 - 2006 - "Maidhill Chinnappan - cancer survivor - sponsored by Connex for Peter Mac, 2 Hour Concession - 12-8-2006 Demonstrates one of many different types of Metcards issued during the period of used in Melbourne from 1996 to 2013Set of six Metcard tickets - printed on light card with a magnetic stripe. Has the ticket number and contact details, Metcard and Metlink logo on the front of the card.trams, tramways, tickets, metcard, metlink, kids under cover, walk to cure diabetes, peter mac, connex, bunnings, alfred hospital, maidhill chinnappan -
Melbourne Tram Museum
Ephemera - Metcards - event promotion - set of 6, Metlink, 2006 - 2007
... -2006 Demonstrates one of many different types of Metcards ...Set of six Metcards with the Metcard logo and transport Mode icons. Tickets were used to promote events and transport. Two copies of each ticket held except for items 5 & 6. 1 - 2007 - "Catch a ticket to all the action" - Cricket at the MCG - Off-Peak daily - 3-5-2007 and Daily full fare - 07-03-2007 2 - 2007 - Fina swimming event - both blank on the rear 3 - 2007 - Merv's Walk to the G - cricket - Daily full fare - 26-12-2007 and Daily Concession - 28-1-2008 4 - 2006 - Barry Humpries, EdnaFest - 2-hour concession - 14-12-2006 and Off-Peak Daily with a possible footy tips list on the rear - 19-4-2007 5 - undated - Melbourne food promotion - rear blank, but with use printed on the front - daily concession 6 - 2006 - Commonwealth Games, 2-hour concession - 6-12-2006 Demonstrates one of many different types of Metcards issued during the period of used in Melbourne from 1996 to 2013Set of six Metcard tickets - printed on light card with a magnetic stripe. Has the ticket number and contact details, Metcard and Metlink logo on the front of the card.trams, tramways, tickets, metcard, metlink, cricket, mcg, fina, swimming, merv hughes, barr humpries, ednafest, commonwealth games -
Melbourne Tram Museum
Ephemera - Metcards - World Aids Day - set of 3, Metlink, 2007 - 2009
... - Daily concession - 15-2-2010 Demonstrates one of many different ...Set of three Metcards with the Metcard logo and transport Mode icons. Tickets were used to promote World AIDS Day. Two copies of each ticket held except for item 3. 1 - 2007 - December 1, Daily Full Fare - 22-11-2007 and 2 hour concessioin - 27-12-2007 2 - 2008 - 2 hour concession - 6-11-2008 and 14-11-2008 3 - 2009 - Daily concession - 15-2-2010 Demonstrates one of many different types of Metcards issued during the period of used in Melbourne from 1996 to 2013Set of three Metcard tickets - printed on light card with a magnetic stripe. Has the ticket number and contact details, Metcard and Metlink logo on the front of the card.trams, tramways, tickets, metcard, metlink, aids, world aids day -
Melbourne Tram Museum
Ephemera - Metcards - Celebrities - set of 9, Metlink, 2007 - 2009
... one of many different types of Metcards issued during ...Set of nine Metcards with the Metcard logo and transport Mode icons. Tickets were used to record or mark the activities of well-known celebrities or personalities. Two copies of each ticket held. All are bar-coded on the rear and have the availability printed on the front of the ticket. 1 - 2008 - Glenn & Kantrina Manton - whitelion.org.au - Daily Full Fare, 1-7-2008 and 6-11-2008 2 - 2008 - Livinia Nixon - Channel 9 - 2 hour concession x 10 and daily concession - 11-2-2008 and 2nd has a blank rear, 3 - 2007 - Kate Ceberano - 2 x 10 and Daily concession - 23-11-2007 and 2 May 2008 4 - 2008 - Lord Mayor - John So - 2-hour concession and 2-hour concession x 10 - 19-3-2008 and 25-2-2008 5 - 2008 - Dannii Minogue - 2-hour concession x 10 and Daily concession - July 2008 6 - 2008 - Michael Kim - 2 hour concession - 13-3-2008 and 20-3-2008 7 - 2008 - Nicole Livingstone - 2 hour full fare and two-hour x 10 concession - May and March 2008] 8 - 2009 - Ron Barassi - 2 hour concession a 2 hour full fare x 10 - Jan 2009 and 7-3-2009 9 - 2008 - Garry Lyon - daily full fare and two hour x 10 concession - Feb 2008 and 27-6-2008 Demonstrates one of many different types of Metcards issued during the period of used in Melbourne from 1996 to 2013Set of nine Metcard tickets - printed on light card with a magnetic stripe. Has the ticket number and contact details, Metcard and Metlink logo on the front of the card.trams, tramways, tickets, metcard, metlink, glenn & kantrina manton, livinia nixon, kate ceberano, john so, dannii minogue, michael kim, nicole livingstone, ron barassi, garry lyon -
Melbourne Tram Museum
Document, Beaumaris Tramway Company Limited - Rules for Drivers
... and partly typed. Provides 70 different rules or instructions... of a document from an original source, handwritten and partly typed ...Copy of a document from an original source, handwritten and partly typed. Provides 70 different rules or instructions to the drivers of horse trams for the Beaumaris Tramway Company Limited - what they "MUST" do, personal behavior, tickets, ticket punches, instructions with regard to trip slips, handling of the Ticket Punch Register device and tramway operations.Yields information about the rules for tram drivers for the Beaumaris Tramway Co. Ltd.Blue paper, typed notes, six sheets, titled Beaumaris Tramway Company Limited - Rules for Drivers - three duplicate sheets of pages 4 to 6.Each of the first six sheets have a pen mark signifying, that it has been retyped.tramways, trams, beaumaris tramway co. ltd, horse trams, ticket punches, instructions, rules, behaviour -
Ballarat Tramway Museum
Model - Model Sydney R class tram
Model of a Sydney R class tram - operable - painted in Sydney Tramway colours. The Sydney Tramway Museum has a number of them in their fleet though most are stored.Demonstrates an model that represented the later type of a drop-centre saloon car type trams operated on the Sydney tram network until closure in 1961.Model of Sydney Tramways R class tram, plastic with operable trolley poles. HO Scale. Has been fitted with two different motors with "01217" marked on the smaller motor. No information as to the manufacturer.models, tramcars, sydney, r class -
Ballarat Tramway Museum
Document - List, State Electricity Commission of Victoria (SECV), "Numbers and Particulars of Trams" - Ballarat, 5/08/1964
Yields information about the dimensions and equiipment on Ballarat Tramcars operated by the SEC.Typed List of tramcars and their details for Ballarat dated 5-August-1964, titled "Numbers and Particulars of Trams". Prepared by Les Denmead, typed by PB. Ballarat - typed carbon copy - two sheets, are taped together. Gives details of where purchased from , date of purchase, type, body builder, seating capacity, overall length, overall height, overall width, condition of tram, trolley base, Lightning arrester, controller make and type, Truck Maker and type, type of truck, axle type, wheel base, axle diameter, motors type and maker, Motor horsepower, Armature bearings, suspension bearings, gear teeth, Air compressor make and type, Brake Valves make and type, Governor make and type, Weight in tons and details of advertising space in racks. At base has typed (original) list of trams of the two types, single truckers and bogie trams. List of trams includes the scrubber and No. 20 which was scrapped prior to system closure. See also 8721 and 8722 for other versions - different dates and 8690 for a Bendigo list. Note: Framed copies of both Ballarat and Bendigo are held in the depot. Some changes have been made to the tramcars since the preparation of this sheet and there are some errors and differences. See also Reg Item 6879 for an annotated version.In black ink, top right hand corner - "Ballarat Tramway Preservation Society Cat No. 613"tramcars, ballarat, equipment, lists, data -
Ballarat Tramway Museum
Document - List, State Electricity Commission of Victoria (SECV), "Numbers and Particulars of Trams" - Ballarat, 11/5/1961
Ballarat - Gives details of where purchased from , date of purchase, type, body builder, seating capacity, overall length, overall height, overall width, condition of tram, trolley base, Lightning arrester, controller make and type, Truck Maker and type, type of truck, axle type, wheel base, axle diameter, motors type and maker, Motor horsepower, Armature bearings, suspension bearings, gear teeth, Air compressor make and type, Brake Valves make and type, Governor make and type, Weight in tons and details of advertising space in racks. At base has typed (original) list of trams of the two types, single truckers and bogie trams. List of trams includes the scrubber and No. 20 which was scrapped prior to system closure. See also 3430 and 8722 for other versions - different dates and 8690 for a Bendigo list. Note: Framed copies of both Ballarat and Bendigo are held in the depot. Some changes have been made to the tramcars since the preparation of this sheet and there are some errors and differences. See also Reg Item 6879 for an annotated version.Yields information about the dimensions and equiipment on Ballarat Tramcars operated by the SEC.Typed List (Carbon copy) of tramcars and their details for Ballarat dated 11 May 1961, titled "Numbers and Particulars of Trams". Two sheets which have been taped together. tramcars, ballarat, equipment, lists, data -
Ballarat Tramway Museum
Document - List, State Electricity Commission of Victoria (SECV), "Numbers and Particulars of Trams" - Ballarat, 5/9/1966
Ballarat - Gives details of where purchased from , date of purchase, type, body builder, seating capacity, overall length, overall height, overall width, condition of tram, trolley base, Lightning arrester, controller make and type, Truck Maker and type, type of truck, axle type, wheel base, axle diameter, motors type and maker, Motor horsepower, Armature bearings, suspension bearings, gear teeth, Air compressor make and type, Brake Valves make and type, Governor make and type, Weight in tons and details of advertising space in racks. At base has typed (original) list of trams of the two types, single truckers and bogie trams. List of trams includes the scrubber and No. 20 which was scrapped prior to system closure. See also 3430 and 8721 for other versions - different dates and 8690 for a Bendigo list. Note: Framed copies of both Ballarat and Bendigo are held in the depot. Some changes have been made to the tramcars since the preparation of this sheet and there are some errors and differences. See also Reg Item 6879 for an annotated version.Yields information about the dimensions and equiipment on Ballarat Tramcars operated by the SEC.Dyleline print of a typed List of tramcars and their details for Ballarat dated 5 September 1966 (typed on), titled "Numbers and Particulars of Trams". tramcars, ballarat, equipment, lists, data -
Melbourne Tram Museum
Ephemera - Set of 6 sheets of "Schoolboy Howler" tram tickets, Melbourne & Metropolitan Tramways Board (MMTB), 1930s
The MMTB printed advertising on the back of tram tickets or these "Schoolboy Howlers" along with promoting the advertising on the back of tickets using the phase "Melbourne trams and buses carry 1,000,000 passengers a day" Ticket values are 1d , 2d, 2d City Section, 3d, 4d and 6d. The collection comprises over 60 different howlers of the times. Produced during the late 1930s and early 1940s.Demonstrates the use of the rear of Melbourne tram tickets for advertising.Set of over 60 Schoolboy howler Melbourne tram tickets sorted primarily by value and type.tramways, mmtb, tickets, schoolboy howlers, advertising -
Ballarat Tramway Museum
Equipment - Part of overhead - corroded span wire, 2024
Items show two different wire terminations - fully wrapped - 7 wires and part wrapped and secured by bending the wire. Shows how the galvanized span wire - 7 strands - can corrode within the insulator and lead to failure if not inspected and replaced. The items were probably erected by the SEC during the mid 1930s and replaced by the BTM 2024. Salvaged from Wendouree Parade during overhead span wire replacement and repair work March 2024 undertaken by the BTM. See also item 9020 for a corroded pole eye bolt.Demonstrates a corroded span wire and a typical egg type insulator.Overhead equipment - two brown egg insulators with associated corroded span wire.overhead, insulators, span wires, btm, tramways -
Ballarat Tramway Museum
Document - Photocopy, Ballarat Tramway Preservation Society (BTPS), "Brill's 21-E traction truck", 1970's
Demonstrates aspects of the two types of trucks or bogies used on Ballarat trams and their design basis. Photocopied from a catalogue.Five pages, each page trimmed to a slightly different width, photocopy of an article titled "Brill's 21-E traction truck", reproduced from the 1905 Brill catalogue. Gives details of the truck, its capability, basis, use in New York for example, how it functions, load and speed capacity, motor size, basic dimensions, limitations and drawings. 2nd copy held as well - on toner based copy rather than heat sensitive paper. Scanned copies of all sheets added 25/3/15.trams, tramways, trucks, 21e trucks, brill trucks -
Ballarat Tramway Museum
Document - Photocopy, Ballarat Tramway Preservation Society (BTPS), "Maximum-traction truck: Brill Eureka", 1970's
Demonstrates aspects of the two types of trucks or bogies used on Ballarat trams and their design basis. Photocopied from a catalogue.Five pages, each page trimmed to a slightly different width, photocopy of an article titled "Maximum-traction truck: Brill Eureka", reproduced from the 1905 Brill catalogue. Gives details of the truck, its capability, basis, use in New York for example, how it functions, load and speed capacity, motor size, basic dimensions, limitations and drawings. Copy made at time of filing. Scanned copies of all sheets added 25/3/15.trams, tramways, trucks, maximum traction, brill trucks -
Flagstaff Hill Maritime Museum and Village
Container - Kitchen Canister set, Late 19th to early 20th century
This set of kitchen dry food canisters is made of metal; each container has a different height, width and capacity. The rolled thin metal has created a strong, round design with decorative rings on the circumference. The base and close-fitting lid protect the contents from vermin and most insects, and the handle on top aids in the removal of the lid. Metal containers like these are reusable and can be re-purposed, which is advantageous when living in regional or rural areas. The type of manufacture indicates that the set was made in the late 19th to early 20th century. Gradually, colourful and attractive plastic kitchenware began to replace metalware. One of the canisters is labelled 'coffee'; coffee plants and seeds were transported from Brazil into Australia in 1788 when the First Fleet arrived although their growth was unsuccessful. However, by the 1920s, a tenth of the Australian population was drinking readily stored coffee. Large quantities of harvested grains such as maize, wheat and barley were protected from pests by being stored in airy buildings, often raised from the ground. This was an age-old practice used by civilizations such as the ancient Egyptians and early Hebrews. Smaller quantities of food for short-term use in the homes were stored in woven baskets or clay pots.This set of kitchen food containers is an example of colonial food storage used in a domestic setting to store and preserve dry ingredients. These canisters give a snapshot of early domestic life in Australia. Canister set; four cylindrical cream coloured metal canisters with domed lids that have lift-up handles on top. They are made from rolled metal and the bases and lids have a side seam. Each canister is a different size and displays a label for different contents. The adhesive labels are vertical, and a gold colour with black vertical text. The cream paint has brush strokes and small areas have exposed green paint under the cream. The insides of the bases are painted dark grey but the lids have no paint underneath. The empty canisters can fit one inside the other. Labels, in descending order: "FLOUR" "RICE" "SAGO" "COFFEE"flagstaff hill, flagstaff hill maritime museum and village, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, canister set, kitchen storage, food storage, metal canisters, dry food storage, food packaging, kitchen container, vintage, flour, rice, sago, coffee, kitchenalia, late 19th to early 20th centuries, nesting canisters -
Melbourne Tram Museum
Photograph - Set of four Colour Prints, Melbourne & Metropolitan Tramways Board (MMTB), c1975
Colour print of Leyland National Mark 1 bus as delivered, c1975. .1 - bus 818, at Doncaster Shoppingtown setting down passengers - two copies held. .2 - bus 81- at Doncaster depot - two copies held .3 - ditto - different view .2 .4 - interior photograph of the above bus type. MMTB Photograph? Two copies held tramways, mmtb, buses, leyland, mmtb buses, doncaster depot, doncaster rd, national class -
Kiewa Valley Historical Society
Spanners - Open ended x2
Spanners are used to tighten nuts of different sizes. These spanners are large and were used on larger items eg. H.V. McKay machinery. Used by residents of the Kiewa Valley.Both spanners are straight and made of steel. The 'H.V. McKay' spanner has '824' on the back (at the 'knob' end) and has a 'knob' at one end. The other spanner has the same type of opening at each end (no knob) and has embossed '55A' on one side at one end.H. V. McKay embossed (at the knob end) on one spanner and 824 on the back of it. 55A embossed on one side of the other spannerspanners, h.v.mckay -
Flagstaff Hill Maritime Museum and Village
Tatting Shuttle
Tatting is a form of knotted lace making using thread and a small shuttle. Twisted threads are tied around or through small, pointed shuttles that can be made of bone, mother of pearl, tortoise shell, steel or plastic. This produces a stable, strong lace using simple knots of two half hitches to make rings and chains embellished with picots. The origins of tatting are not clear but early versions of decorative knotting were used by the Egyptians on their ceremonial dress. Tatting also has elements of fishermen's net making techniques and the decorative knotting that was practiced by aristocratic women from the 15th century. Tatting, as we know it today, emerged in the first half of the 19th century. The new availability of mercerised thread from 1835 encouraged a burgeoning of lace crafts of all sorts. It was known in Italy as "occhi" and in France as "la frivolite". Tatting looks fragile but is both strong and durable. An article in a column named "Wives and Daughters" published in the Star newspaper in May 1910 describes the durability of tatting lace - "there is edging and insertion still in existence that have outworn two sets of pillow slips." In the 19th century and well into the 20th century, tatting was used like crochet and knitted lace for decorative edgings, collars, doylies, tray cloths etc. At first, different tatting patterns were passed along by word of mouth from person to person, however in time, patterns regularly appeared in newspapers and magazines well into the 1950's. A shuttle is a small tool that looks like a small boat "sailing" in and out of the thread. Tatting is called "schiffchenarbeit" in German, which means "the work of a little boat". There are two popular types of shuttles. The first has closed ends and a removable bobbin where the thread is wound around - often made from metal or plastic. The second type has a post in the center where the thread is wound. The ends of this bobbin are open but snug. Because it is constructed in two pieces, it can be made from materials like bone, ivory or mother of pearl. Shuttles hold a larger amount of thread (as compared with needles) which means fewer ends to weave in. Fishermen in the past are thought to have used large shuttles to weave cord into certain knots whilst making their fishing nets. Their methods were copied by weavers, who innovated by using threads and smaller shuttles to make lace.Tatting Shuttle, Black plastic, "ARCHER" inscribed. "ARCHER" inscribed.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, tatting shuttle, handcraft, needlework -
Flagstaff Hill Maritime Museum and Village
Tatting Shuttle
Tatting is a form of knotted lace making using thread and a small shuttle. Twisted threads are tied around or through small, pointed shuttles that can be made of bone, mother of pearl, tortoise shell, steel or plastic. This produces a stable, strong lace using simple knots of two half hitches to make rings and chains embellished with picots. The origins of tatting are not clear but early versions of decorative knotting were used by the Egyptians on their ceremonial dress. Tatting also has elements of fishermen's net making techniques and the decorative knotting that was practiced by aristocratic women from the 15th century. Tatting, as we know it today, emerged in the first half of the 19th century. The new availability of mercerised thread from 1835 encouraged a burgeoning of lace crafts of all sorts. It was known in Italy as "occhi" and in France as "la frivolite". Tatting looks fragile but is both strong and durable. An article in a column named "Wives and Daughters" published in the Star newspaper in May 1910 describes the durability of tatting lace - "there is edging and insertion still in existence that have outworn two sets of pillow slips." In the 19th century and well into the 20th century, tatting was used like crochet and knitted lace for decorative edgings, collars, doylies, tray cloths etc. At first, different tatting patterns were passed along by word of mouth from person to person, however in time, patterns regularly appeared in newspapers and magazines well into the 1950's. A shuttle is a small tool that looks like a small boat "sailing" in and out of the thread. Tatting is called "schiffchenarbeit" in German, which means "the work of a little boat". There are two popular types of shuttles. The first has closed ends and a removable bobbin where the thread is wound around - often made from metal or plastic. The second type has a post in the center where the thread is wound. The ends of this bobbin are open but snug. Because it is constructed in two pieces, it can be made from materials like bone, ivory or mother of pearl. Shuttles hold a larger amount of thread (as compared with needles) which means fewer ends to weave in. Fishermen in the past are thought to have used large shuttles to weave cord into certain knots whilst making their fishing nets. Their methods were copied by weavers, who innovated by using threads and smaller shuttles to make lace.Tatting Shuttle, tortoise-shellflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, tatting shuttle, handcraft, needlework -
Flagstaff Hill Maritime Museum and Village
Tatting Shuttle
Tatting is a form of knotted lace making using thread and a small shuttle. Twisted threads are tied around or through small, pointed shuttles that can be made of bone, mother of pearl, tortoise shell, steel or plastic. This produces a stable, strong lace using simple knots of two half hitches to make rings and chains embellished with picots. The origins of tatting are not clear but early versions of decorative knotting were used by the Egyptians on their ceremonial dress. Tatting also has elements of fishermen's net making techniques and the decorative knotting that was practiced by aristocratic women from the 15th century. Tatting, as we know it today, emerged in the first half of the 19th century. The new availability of mercerised thread from 1835 encouraged a burgeoning of lace crafts of all sorts. It was known in Italy as "occhi" and in France as "la frivolite". Tatting looks fragile but is both strong and durable. An article in a column named "Wives and Daughters" published in the Star newspaper in May 1910 describes the durability of tatting lace - "there is edging and insertion still in existence that have outworn two sets of pillow slips." In the 19th century and well into the 20th century, tatting was used like crochet and knitted lace for decorative edgings, collars, doylies, tray cloths etc. At first, different tatting patterns were passed along by word of mouth from person to person, however in time, patterns regularly appeared in newspapers and magazines well into the 1950's. A shuttle is a small tool that looks like a small boat "sailing" in and out of the thread. Tatting is called "schiffchenarbeit" in German, which means "the work of a little boat". There are two popular types of shuttles. The first has closed ends and a removable bobbin where the thread is wound around - often made from metal or plastic. The second type has a post in the center where the thread is wound. The ends of this bobbin are open but snug. Because it is constructed in two pieces, it can be made from materials like bone, ivory or mother of pearl. Shuttles hold a larger amount of thread (as compared with needles) which means fewer ends to weave in. Fishermen in the past are thought to have used large shuttles to weave cord into certain knots whilst making their fishing nets. Their methods were copied by weavers, who innovated by using threads and smaller shuttles to make lace.Tatting Shuttle, black plastic flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, tatting shuttle, handcraft, needlework