See 1833.02 for more information about Little Bay St. Ed WHITING lived in Dow St Port Melbourne in 1930s (A PMHPS Member in 2000s). Photos copied by Ed WHITING for PMHPS include Violet JOHNSON (now WOODS) as a little girl and later as a young woman. Shows 1930s Port Melbourne life.Note that .01, .02, .05 are in hard copy and a copy of all six is on database Black and white photos (copies) from the 1930s .01 - Ed WHITING and friend Ron .02 - Ed WHITING and three friends at BP filling station on Beach St near Princes Pier .03 - Ed WHITING and two friends in Port Melbourne lane.(database) .04 - Violet JOHNSON and friends, Port Melbourne backyard area (database) .05 - Violet JOHNSON and friend on Little Bay St .06 - Violet JOHNSON with pretend gun (database)families, domestic life, built environment - domestic, engineering - roads streets lanes and footpaths, edwin whiting, violet johnson, violet woods johnson

Double Headed Rail from Ravenswood Station Siding which was dismantled circa 1987 the two rails were stored for a time at Maldon before being donated to Puffing Billy Museum Bearing makers marks of Wilson & Cammell - Dronfield- Steel works Wilson & Cammell made Steel rails at their Dronfield Steel Works, in Dronfield, North East Derbyshire, England from 1872 - 1883 Double-headed rail In late 1830s Britain, railway lines had a vast range of different patterns. One of the earliest lines to use double-headed rail was the London and Birmingham Railway, which had offered a prize for the best design. This rail was supported by chairs and the head and foot of the rail had the same profile. The supposed advantage was that, when the head became worn, the rail could be turned over and re-used. In practice, this form of recycling was not very successful as the chair caused dents in the lower surface, and double-headed rail evolved into bullhead rail in which the head was more substantial than the foot. Info from Wikipedia - Rail Profile https://en.wikipedia.org/wiki/Rail_profile The first records of double headed rail being used In Victoria by Victorian Railways was in 1859, the rails, chairs, oak and trenails were imported from UK. After the 1870’s the Victorian Railways went over to using flat bottom rails, but they still needed replacement double headed rail for lines already laid and this continued up to at least 1883 Wilson & Cammell - Dronfield- Steel works Wilson & Cammell made Steel rails at their Dronfield Steel Works, in Dronfield England from 1872 - 1883 Mount Alexander & Murray River Railway The Melbourne, Mount Alexander & Murray River Railway Company received parliamentary assent in February 1853 to build Victoria's first inland railway from Melbourne to Williamstown, and Melbourne to Bendigo and Echuca. Construction commenced in January 1854 with work on a pier at Williamstown but lack of funds slowed progress, eventually prompting the company to sell out to the government. The 100-mile (162 km) section to Bendigo opened in October 1862. Its cost of £35,000 per mile made it the most expensive railway ever built in Australia. In 1864, the line was extended to Echuca, tapping into the booming Murray-Darling paddlesteamer trade. info from Museums Victoria - Victorian Railways https://museumsvictoria.com.au/railways/theme.aspx?lvl=3&IRN=450&gall=456 1863 Ravenswood Station open on the 1st Feb 1863 Victorian Railways - purchased and imported the Rail and Chairs from Raleigh, Dalgleish, White and Co. London Importation of railway plant : abstract of a return to an order of the Legislative Assembly dated 27th June 1860 for - Copies of the advertisements calling for tenders, the names of the tenderers and the accounts and correspondence with Mr Brunel relating thereto GP V 1859/60 no. C 15 http://www.parliament.vic.gov.au/papers/govpub/VPARL1859-60NoC15.pdf Report from the Select Committee upon the Importation of Railway Plant : together with proceedings of the Committee, minutes of evidence and appendix GP V 1859/60 no. D 38 (2.9 MB) http://www.parliament.vic.gov.au/papers/govpub/VPARL1859-60NoD38.pdf Ravenswood Siding When the Victorian Railways were established in 1856 they adopted one of the popular British permanent way standards - heavy 80lb (36.3kg) double-headed rail held up right in cast iron chairs attached to transverse timber sleepers by wooden pegs called trenails. The Ravenswood Railway siding was constructed in 1862 with 12 feet wrought iron double-head rail held in cast iron chairs with Ransom and May patent compressed keys. Trenails held the chairs to the sleepers and the joints were secured in joint chairs. Joints were subsequently joined using fish plates. It formed part of the Melbourne to Echuca rail line, initially known as the Melbourne, Mt Alexander and Murray River Railway. George Christian Derbyshire, the first Engineer-in-Chair of the Victorian Railways was responsible for the design and construction of the works. No new lines were built in Victoria using double-headed rail after 1870. The siding was disconnected from the main line in 1988. The Ravenswood Railway Siding demonstrates the original 1856 philosophy of the Victorian Railways to adopt British permanent way technology. The siding demonstrates significant aspects in the development of permanent way technology in England and Victoria over the period from the 1830's to the 1880's. The chairs in the Ravenswood siding are physical evidence of early railway technology rendered obsolete 120 years ago, namely joint chairs at rail joints and trenails to secure the chairs to the sleepers. The double-headed rail demonstrates an important stage in the evolution of British rail technology in the 1830s. The old fish plates, square headed bolts and square nuts demonstrate the success of fishing the rail joins. The Ravenswood siding demonstrates the earliest form of rail joint technology developed in England, and existing in Australia, the joint chair. In part of the siding the sequence of joint and intermediate chairs is consistent with the 1856 specifications, that sequence is rare with the joints secured in joint chairs. The survival of chairs in this sequence is rare and almost certainly demonstrates that they remained in continuous use at the same location from 1862 to 1988. This remnant of the Ravenswood siding has survived 126 years. The siding has proved to be the most significant of extant remnant double-headed sidings in Victoria, containing a rare combination of early permanent way technologies. Construction dates 1862, Info from Ravenswood Railway Siding Victorian Heritage Database Report http://vhd.heritagecouncil.vic.gov.au/places/4693/download-report The remaining section of this siding is significant at the State and National levels in that it demonstrates the use of chaired rail by the Victorian Railways Department for the Trunk Lines and, more particularly, the following stages in the evolution of this long obsolete method of permanent way construction: a) The use of joint chairs and intermediate chairs at regular intervals inferring that the original wrought iron rail lengths were 12 feet, as is known through documentary sources to have been the case. The survival of chairs in this sequence is unique and almost certainly demonstrates that they have remained in continuous use at the same location and in the same sequence from 1862 to 1988 . b) The use of joint chairs and intermediate chairs designed for use with trenails. c) The use of later intermediate chairs designed for use with steel pins and the use of fished joints with steel double head chaired rail, representing a second method of constructing the permanent way using chaired rail technology. info from Ravenswood Siding - Melbourne/Echuca Railway Line - Victorian Heritage Database Report http://vhd.heritagecouncil.vic.gov.au/places/70103/download-report Addition to Citation for Melbourne to EchucaRailway Line 1/10/1990 Double Head Rail The surviving lengths of double head rail with chairs on this railway compare with one surviving similar remnant on the Geelong to Ballarat railway and are representative of permanent way construction techniques applied exclusively to the two trunk railways of the 1860's. In this respect they are rare survivors and may be unique at the national level and of technical importance at the international level to the extent that they enhance contemporary understanding of early railway building technology. Surviving lengths of chaired double head rail survive at Kyneton, Ravenswood and Bendigo on this railway and include a number of different types of cast iron intermediate and joint chairs with hardwood keys and metal pins. The Ravenswood siding is of special significance for the diversity of chair types and for the sequence of chairs recalling rail lengths known to be associated with construction of the line in 1862. Construction of the Railway Tenders closed on 24 March 1858 with no less than 133 tenders being received. A contract was let to Cornish and Bruce for £3,356,937 to commence work on 1 June 1858 and complete the line by 31 July 1861. Cornish and Bruce made quick early progress with the Melbourne to Sunbury section being officially opened on 13 January 1859. The line was officially opened to Bendigo (Sandhurst) on 20 October 1862 by the Governor of Victoria, Sir Henry Barkly. A great banquet was held for 800 guests and this was followed by a grand ball. The extension of the line to Echuca was a relatively simple matter as that part of the line was across plain country without any significant engineering challenges. Tenders were called for the work in 1863 and the work was completed in 1864 by contractors Collier and Barry Apart from the line contractors, other firms directly involved were J Shire law and Co (sleepers), R Fulton, Langlands Brothers and Co, William Crossley (water supply), B Moreland, Langlands Brothers and Co (platelayers lorries), E Chambers (iron pins, traversers), Miller and McQuinstan (luggage vans and steam engines) and various contractors for building works. Info from Engineers Australia Engineering Heritage Victoria Nomination for Recognition under the Engineering Heritage Australia Heritage Recognition Program for the Goldfields Railways - Melbourne , Bendigo & Echuca Railway Page 25 - .2.9.2 Statement from National Trust of Australia (Victoria) Listing number B5323 for Mt Alexander/Murray Valley Rail Line: Page 69 - Theme 3 https://www.engineersaustralia.org.au/portal/system/files/engineering-heritage-australia/nomination-title/Melbourne_%20Bendigo_Echuca%20Railway%20Nomination.pdf The Melbourne, Mount Alexander and Murray River Railway Company was a railway company in Victoria, Australia. It was established on 8 February 1853 to build a railway from Melbourne to Echuca on the Victorian-NSW border and a branch railway to Williamstown. The company struggled to make any progress and on 23 May 1856, the colonial Government took over the Company and it became part of the newly established Department of Railways, part of the Board of Land and Works. The Department of Railways became Victorian Railways in 1859. Construction of the Bendigo line commenced in 1858, but this private consortium also met with financial difficulties when it was unable to raise sufficient funds, and was bought out by the Victorian colonial government. The design work was then taken over by Captain Andrew Clarke, R. E., Surveyor-General of Victoria, with bridge designs completed by Bryson and O'Hara The contract for the first stage of the line from Footscray to Sandhurst (now Bendigo), was let to Cornish and Bruce for £3,356,937.2s.2d ($6.714 million) with work commencing on 1 June 1858. Completion of the permanent way was to be by 31 July 1861 https://en.wikipedia.org/wiki/Melbourne,_Mount_Alexander_and_Murray_River_Railway_Company Victorian Railways - purchased and imported the Rail and Chairs from Raleigh, Dalgleish, White and Co. London Importation of railway plant : abstract of a return to an order of the Legislative Assembly dated 27th June 1860 for - Copies of the advertisements calling for tenders, the names of the tenderers and the accounts and correspondence with Mr Brunel relating thereto GP V 1859/60 no. C 15 http://www.parliament.vic.gov.au/papers/govpub/VPARL1859-60NoC15.pdf Report from the Select Committee upon the Importation of Railway Plant : together with proceedings of the Committee, minutes of evidence and appendix GP V 1859/60 no. D 38 (2.9 MB) http://www.parliament.vic.gov.au/papers/govpub/VPARL1859-60NoD38.pdf Victorian Railways : report of the Board of Land and Works November 1862 GP V 1862/63 no. 21 (2.8 MB) https://www.parliament.vic.gov.au/papers/govpub/VPARL1862-63No21.pdfHistoric - Victorian Railways - Double Headed rail Ravenswood Railway Station and Siding Victorian Heritage Database Reports Victorian Heritage Register VHR H1100 Victorian Heritage Register VHR H1786 National Trust VHR H1100 Mount Alexander and Murray River Rail way Line National Trust2 rail lengths of Double Headed Rail made of Iron makers marks : Wilson & Cammell - Dronfield - Steel and 20 joint chairs with metal rail pins Makers mark Wilson & Cammell - Dronfield - Steel (possible date 187? very hard to read ) puffing billy, double headed rail, wilson & cammell - dronfield - steel works, ravenswood station siding, melbourne to echuca rail line, initially known as the melbourne, mt alexander and murray river railway.

Colour photograph of transfer pump moored to north end of Eastern Pier. Dredged sand on beach showing pipe line from dredge across sand. Scrub on dune, flagstaff and weather station on dune - top left. Entrance and tip of western pier top right. Lakes Entrance Victoriaboats and boating

The Hygeia was used built in 1890 and could carry 2000 passengers.It was used to transport passengers from Melbourne to Queenscliffe as well as English Royalty at times.RealismBlack & white photograph of the "HYGEIA" at Queenscliffe wharfHYGEIA 1903 on the reversesteam ship, "hygeia, queenscliffe wharf

Rocket equipment which has been used in various lifeboat and rocket stations on the Victorian Coast. It is unclear if this is the original rocket equipment from Port Campbell. This equipment, if not original has been used in rescue operations and is identical to the equipment that has been in use at Port Campbell from C.1890 onwards.Metal, brass and timber tripod structure with a channel or trough to support the rocket. It has a pendulum and dial to measure the height trajectory. Very long wooden box with hinged lid painted a green-grey colour with four brass hinges and two rusted metal hooks.

Rocket equipment which has been used in various lifeboat and rocket stations on the Victorian Coast. It is unclear if this is the original rocket equipment from Port Campbell. This equipment, if not original has been used in rescue operations and is identical to the equipment that was in use at Port Campbell from C.1890 onwardsTwo cylindrical rockets made of base metal with orange painted wooden heads. Three long cedar, wooden sticks (octaganal) that attach to the rockets. They have spring clips and a section of metal and a sheath to protect the wood from fire and with grooves for the rope. One rocket is attached firmly to a stick. A long length of cotton/linen (?) rope is attached to one of the rocketsYes

This rocket equipment has been used in various lifeboat and rocket stations on Victorian Coast. It is unclear if this is the original rocket equipment from Port Campbell. This equipment, if not original to the site, has been used in rescue operations and is identical to the equipment that was in use at Port Campbell from C.1890 onwardsTwo canvas lifejackets, one is filled with cotton or silk and the other with cork. The jackets are sewn in sections that hold either the cork or the cotton/silk. One of the lifejackets has a separate strap and brass eyelets and buckles.

This rocket equipment has been used in various lifeboat and rocket stations on Victorian Coast. It is unclear if this is the original rocket equipment from Port Campbell. This equipment, if not original to the site, has been used in rescue operations and is identical to the equipment that was in use at Port Campbell from C.1890 onwardsTwo rope ladders, identical in format and length. The rungs are made from another type of material.

This rocket equipment has been used in various lifeboat and rocket stations on Victorian Coast. It is unclear if this is the original rocket equipment from Port Campbell. This equipment, if not original to the site, has been used in rescue operations and is identical to the equipment that was in use at Port Campbell from C.1890 onwardsFour rope strops, three are of equal length. Lengths of rope spliced or joined to form a circle of approx. 100cm diameter. The long rope is triple laid rope and the three shorter ropes are made of multiple small strings (approx.40) bound together. Use is yet to be determined.

This rocket equipment has been used in various lifeboat and rocket stations on Victorian Coast. It is unclear if this is the original rocket equipment from Port Campbell. This equipment, if not original to the site, has been used in rescue operations and is identical to the equipment that was in use at Port Campbell from C.1890 onwardsRope handled timber box with faking pins. The Rocket Line was attached to the rocket and fired over the ship in distress. The light rocket line, was folded in such a way that it paid out easily as the rocket shot through the air.

This rocket equipment has been used in various lifeboat and rocket stations on Victorian Coast. It is unclear if this is the original rocket equipment from Port Campbell. This equipment, if not original to the site, has been used in rescue operations and is identical to the equipment that was in use at Port Campbell from C.1890 onwardsEach of the five anchors have an iron ring (2 large, 1 medium, 2 small) to which are attached 5 iron hooks. Medium has 4 hooks.Each has an iron ring 2 large, 2 small to which is attached iron hooks.

This rocket equipment has been used in various lifeboat and rocket stations on Victorian Coast. It is unclear if this is the original rocket equipment from Port Campbell. This equipment, if not original to the site, has been used in rescue operations and is identical to the equipment that was in use at Port Campbell from C.1890 onwardsBody of rescue stretcher is canvas and timber slats. Straps of canvas webbing attached to sides. Rope loops at either end, rope runs along the length of stretcher. Opens out to secure patient.

This rocket equipment has been used in various lifeboat and rocket stations on Victorian Coast. It is unclear if this is the original rocket equipment from Port Campbell. This equipment, if not original to the site, has been used in rescue operations and is identical to the equipment that was in use at Port Campbell from C.1890 onwardsEach of the six iron pegs has a spike on one end and eyelet on the other.

This rocket equipment has been used in various lifeboat and rocket stations on Victorian Coast. It is unclear if this is the original rocket equipment from Port Campbell. This equipment, if not original to the site, has been used in rescue operations and is identical to the equipment that was in use at Port Campbell from C.1890 onwardsRope, 1cm light line

This rocket equipment has been used in various lifeboat and rocket stations on Victorian Coast. It is unclear if this is the original rocket equipment from Port Campbell. This equipment, if not original to the site, has been used in rescue operations and is identical to the equipment that was in use at Port Campbell from C.1890 onwardsRectangular box with fitted lid. All wood. Two rope handles at each end. Inscribed on lid -"Lights Illuminating Wrecks. Mark-IV 3 . 4/7/1910"Inscribed on lid -"Lights Illuminating Wrecks. Mark-IV 3 . 4/7/1910"

Rocket equipment which has been used in various lifeboat and rocket stations on the Victorian Coast. It is unclear if this is the original rocket equipment from Port Campbell. This equipment, if not original has been used in rescue operations and is identical to the equipment that has been in use at Port Campbell from C.1890 onwards.Rope, 1cm light line in wooden box. Wooden rectangular box with lid held by 3 steel hinges. Red painted box, weathered.

Rocket equipment which has been used in various lifeboat and rocket stations on the Victorian Coast. It is unclear if this is the original rocket equipment from Port Campbell. This equipment, if not original has been used in rescue operations and is identical to the equipment that has been in use at Port Campbell from C.1890 onwards.Rope roller, welded, cliff anchor. Steel A frame with eye at top of the A frame. Spindle on bottom for rope to move through.

The Fred Rochow Railways Collection incorporates photos related to the operation of the Wodonga Railway Station including different types of trains and railways staff C. 1930 – 1990. It was donated to the Wodonga Historical Society by Fred Rochow, a railwayman who spent many years based in Wodonga. He joined the Victorian Railways on 17th June l947 and retired in 1988. For some time, he was a member of the Australian Federated Union of Locomotive Enginemen and served a term as a member of the Trades Hall Council. He had an extensive knowledge of the struggles that took place to achieve better conditions for railway workers. Fred worked for many years as a fireman and then worked his way up the ranks to driver, experiencing many changes from the days of steam locomotives through to diesel trains, locomotives and even the modern XPT train. He worked throughout Victoria at different stages of his career, with his final working years focused on the northeast of Victoria and the Albury to Melbourne line. After his retirement, Fred continued to share his love of steam miniature trains with the community.This collection has local and statewide significance as it captures images of trains, locomotives and personnel who operated the railway services in Wodonga and throughout Northeast Victoria. The railways played a critical role in opening up Victoria and connecting Australia for trade, business, social communication and transport.Guard Hugh Fraser about to take his last ride on 10 May 1971. He started his career with Victorian Railways as a Lad Porter on 1 July 1924 at Oakleigh Station. He worked as a Shunter at Korumburra, Williamstown Pier, Woodend and Ballarat. Hugh was Leading Shunter at Wodonga from 1935 until 1941. His final position was as Guard at Wodonga from 1941 until May 1971.railways wodonga, fred rochow, wodonga railwaymen, hugh fraser