This small film development system was developed by Kodak for the amateur photographer. It was a small portable system which made the development of film more accessible to the enthusiast.This is an interesting item and quite innovative and as such has historic and scientific and research significance.A stained wooden rectangular box with dovetailed corners and a lid which is loose and sits inside a ridge.There are two holes drilled in both the longer sides of the box. The lid has a smaller raised section with Kodak Film Tank in red and black text a paper chart is stuck to the underpart of the lid..The interior of the box is painted black and there is a metal cylindrical tin with a lid and inner section.There is a spool attached to one end of the box.There are four loose items, two long prongs with black plastic knobs, a similar length implement with a straight shaft and hooked section on the end and a metal spool.Kodak film Tank on the lid of the box and the lid of the cylinder. The bottom of the cylinder has stamped around the outer rim, " manufactured by Eastman Kodak Co, Rochester NY. Pat Aug 26. 02 May 23 05 May 21 07.Sep 17 07. On the under part of the lid stamped into the timber, ' by Eastman Kodak Co, Rochester NY.kodak film tank, 1907 kodak film tank, warrnambool history

Piano accordions were one form of music used to entertain families and friends prior to electricity being available.Possibly used by Eric Heider (Tenny) Wittingslow who married Iris Baker of Tawonga as his death notice was stored in the same box as the accordion.Wooden handles at each end, one has a leather strap over it. When pulled out wooden ends are attached to the handles and to a thick 'cardboard'. Then 3 red wire frames with green 'cardboard' covering, then wood, then 3 more red & green, then wood, then 3 more red/green and then another thick 'cardboard' attached to the opposite handle. These are the bellows pulling air in and out. The handle with the strap has a keyboard beside it while the other handle has silver knobs that move in when pressed. One side of its original box reads - "The Dudley' Trade Mark ' Nightingale' Accordeon / No. 8018?One handle has 'Dudley'. The other 'Dudley=Accordion'. The middle section has on the end of each of the 4 parts - in metal:- Trade mark with bird in the middle of a triangle. Followed by -Nightingale/Registered/Best Quality/Made in Germany piano accordion, dudley nightingale, musical instrument, dudley acccordeon

A flat-wick lamp is a simple type of kerosene lamp, which burns kerosene drawn up through a wick by capillary action. A flat-wick lamp has a fuel tank (fount), with the lamp burner attached. Four prongs hold the glass chimney, which acts to prevent the flame from being blown out and enhances a thermally induced draft. The glass chimney needs a "throat," or slight constriction, to create the proper draft for complete combustion of the fuel; the draft carries more air (oxygen) past the flame, helping to produce a smokeless light which is brighter than that produced by an open flame. The lamp burner has a flat wick, usually made of cotton. The lower part of the wick dips into the fount and absorbs the kerosene; the top part of the wick extends out of the wick tube of the lamp burner, which includes a wick-adjustment mechanism. Adjusting how much of the wick extends above the wick tube controls the flame. The wick tube surrounds the wick, and ensures that the correct amount of air reaches the lamp burner. Adjustment is usually done by means of a small knob operating a toothed, metal sprocket bearing against the wick. A paraffin lamp with a green metal base to hold fuel with a side screw to adjust wick length. An opaque white glass shield sits in a metal frame attached to base* moorabbin, bentleigh, cheltenham, pioneers, early settlers, market gardeners, lights, lamps, paraffin, oil lamps

Typewriters pre dated computers. This typewriter was possibly used in an office or at home. It was used with an inked tape which may have been only black or had both red and black ink along it. Multiple copies of the material being typed were done using carbon paper inserted between sheets of paper. The original paper was easily identified.Used in the Kiewa Valley.Small grey metal typewriter with deep green key board with gold letters on top.The margin rod is marked in inches and it has keys for pounds, dollars and cents, inches and fractions. The loading of A4 paper is done manually. The keys that hit the paper are stainless steel. The keyboard slopes up to the top which is partially hollow with a gap that exposes the stainless steel keys. The cylinder is at the top and at the back with control knobs on each side. This typewriter has 2 sheets of paper with carbon paper between them to demonstrate how copies were made (but there isn't an inked tape in it so the copies aren't authentic)Centre front: "Royal" Letters of the alphabet on the keys. Centre bottom back: "Royal" and below on a plate: "Built in the British Empire / Protected by American / and Foreign Patents"office. typewriter. royal. carbon paper. decimal currency. office equipment. writing.

The lightweight metal (? tin) suggests this was an everyday item for the working class. It dates to c. 1878 although these were still being sold in 1915 when it was noted that the pot should be rinsed immediately after use with salt water to prevent a tin taste.Old metal French coffee, pot a tapering cylinder fourteen centimeters on the bottom and nine centimeters at the top. It is twenty-eight centimeters high. There is a cap on top with a knob to remove it, there was a hinge attached to the pot which is broken. the wooden handle is 100 centimeters long and 25 centimeters diameter it's attached to a 50 centimeter metal protrusion from the pot. The spout is a tapered tube 140 centimeters long, 30 centimeters diameter at the pot and 15 at its end. there has been some re-soldiering repair where the spout is attached to the pot. Thew spout is at right angle to the handle. the pot has a rusted appearance,coffee pot, miner's item

This medical bureau / cabinet shows several signs of being used for a different purpose before being a medical bureau. It once had the words "GENUINE PURE QUALITY" lettered across the top of the front, as can been still seen from the impression left behind in the stained timber. On each drawer above the handle is a faint impression of something long and rectangular, as though there had been a label attached. The front panel of the drawers is made of the same wood as the rest of the outer cabinet, most probably blackwood. The handles on the drawers are not the original handles either. There are 3 filled-in holes that would form the corners of a triangle, apex at the top, around the perimeter of the current handles. The sides of the drawers are made from plywood and the base made from alternating lengthwise strips of oak and beech wood pressed together, rounded corners at the back and joined to the front panel with metal brackets. The backs of the base of the drawers have four round impressions in them. Along the back edge of the base, in the centre, is a rectangular hole. Between the front pair of round holes is a faint black rounded marking, like the impression made by rubber. The cabinet may have once been a filing cabinet, with the drawers used as document drawers, each with a spring-loaded clamp attached to the back of them to secure documents within. The original handles could have been the half-cup type used for filing cabinets. The construction and use of plywood could place this cabinet in about 1950's.Chest of drawers (or Medical Bureau, or Apothecary Chest, or Filing Cabinet) wooden, dark stained, with 30 small drawers (10 rows, 3 columns). The outer wood of cabinet is possibly blackwood and the edges of top and sides have carved wood decoration. Drawer fronts have bevelled edges and round silver-coloured metal knobs. Drawers have plywood sides, and oak and beech wood bases/, Each drawer has four round depressions (in a square-shaped arrangement) at the back plus a small rectangular hole cut in the centre back of base. A faint impression from previous lettering is evident in the wood stain across top front of cabinet.Impression of previous lettering across top front of cabinet "GENUINE PURE QUALITY". flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, drawers, bureau, cabinet, chest of drawers, furniture, bedroom furniture, household storage, medical bureau, apothecary cabinet, document drawers, filing cabinet

Small wooden handcrafted set of drawers; drawers enclosed in a 'Shell oil' box. On ends of box, printed in black 'Shell' and 'The British Imperial Oil Company Limited' ' 8 Imperial gallons, motor spirit' Small handcrafted drawers are set in the box. Six small drawers, with four wooden knobs, one metal and one loop of wire acting as a drawer pull. Drawers are made from repurposed boxes. One drawer has label of box on side ' Leggo's of Bendigo, Self Raising Roller Flour', parts of label missing 'Good cheap cake' recipe partly visible. On top of drawers, white paint tin stain.

Object. (a) A circular metal disk, slightly convex with six tiny crosses spaced around the outer rim. Shaped like a funnel at the rear, the handle extends into a 16 cm stem which would fit over the walking cane. Eight raised circles decorate the stem, giving a .8 cm decorative ridge. Four circles impressed below the lower edge. A hallmark is impressed below these circles, xo.... with remainder unreadable. (b) Circular rounded top, decorated with concentric small circles, raised slightly, and each centred with a tiny blue gemstone. A larger Royal Blue, circular raised gem stone is at the centre. This knob is 6 cm in diameter.costume accessories, female, ladies walking cane

These four photographs of SPR Santina (Argetto) Straube capturing topographic features – plotting with a Wild B8 stereo plotter were most likely taken in c1980. Introduced in 1966, the Wild B8 stereo plotter was used for plotting topographic detail and contours. These analogue machines were manually controlled by adjusting the control knobs for the orientation of the 3D image. The B8s used a nine-inch square photo image on a film or glass diapositive which allowed highly accurate extraction of map features. At first, plotting by B8 and B9 equipment was undertaken at the aerial photography scale of 1:80,000 in pencil onto a controlled plotting sheet. Sheets were then inked up and reduced photographically to the 1: 100,000 publication scale for scribe impression production. In these photos SPR Santina (Argetto) Straube was plotting with a pencil or ink pen mounted at the far end of the pantograph arm. The plotting procedure was upgraded to direct plotting in ink with photographic reduction to publication scale. In 1975 four B8s were upgraded with tri-axis locaters as part of the Input Sub-system to enable digital extraction to AUTOMAP 1’s topographic database. When AUTOMAP 2 was introduced in 1982 these B8s were upgraded, and additional machines added to expand the Army Survey Regiment’s digital capture capability. This is a set of four photographs of a technician capturing topographic Features with a Wild B8 stereo plotter in Air Survey Squadron – Army Survey Regiment, Fortuna, Bendigo. 1980. The photographs were on 35mm negative film and were scanned at 96 dpi. They are part of the Army Survey Regiment’s Collection. .1) to .4) Photo, black & white, c1980. SPR Santina (Argetto) Straube operating a Wild B8 stereo plotter..1P to .4P – no annotations.royal australian survey corps, rasvy, army survey regiment, army svy regt, fortuna, asr, air survey, photogrammetry

The Display Board of Konts was handmade in Kings Lynn, Devon, England, by Tom Long DSM, who is a member of the International Guild of Knot Tyers. This display board shows the knots and joins used in ropework performed by a sailmaker and other skilled ropeworkers. It demonstrates the uses of some of the knots, such as for knobs and handles, suspending lengths of wood, reinforcing spliced rope and even for decorative work. The sailmakers travelling as part of the ship’s crew stored their tool kit in a canvas ditty bag. It contained needles, awls, a sailmaker’s leather palmed glove with a heavily reinforced palm - a shuttle to mend and make nets, fids, knives, mallets, brushes, rulers, and rope gauges. Sailmakers used their ropework and knot-making skills for various purposes and chose the type of rope fibre for its particular properties. For example, Italian hemp rope was preferred for the light line used in shore-to-ship rescues because it was lightweight, not easily knotted, and absorbed less water. A supply of various types of rope was a commodity on board a ship and on land in the new colonies. It was flexible, easily stored, and could be worked to create an endless variety of objects on its own or with other materials like wood. An example is a simple rope ladder. Lengths could be combined to make various thicknesses and pieces could be skilfully joined together by splicing. The importance of knots in seafaring cannot be overestimated. When ships relied on only the wind for power and speed, there were a huge number of various ropes in use, particularly with regard to the sails and rigging. Seafarers would be judged on their ability to tie knots speedily and correctly. A mounted display of authentic seaman's knots is on a board covered in blue fabric. Various rope grades and fibres were used to work numerous knots and splices. Some of the uses are familiar, such as the toggle, the pineapple knot, and the Turk’s head. A selection of rope grades and fibres were used to work numerous knots and splices. Some of the uses are familiar, such as the toggle, the pineapple knot, and the Turk’s head. The name or purpose of the knot is on the label below it. Labels below each knot give its name or use.flagstaff hill, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, knot display, knot making, ropework, marine technology, sailmaker's work, sailor's knots, ship's rigging, seamen's knots, handmade, rope craft, knots, splices

The phonograph is a mechanical device for the recording and reproduction of sound and originally used a tinfoil sheet wrapped around a rotating cylinder to produce the sound. It was invented by Thomas Edison of U.S.A. in 1877 and was the model for all phonographs or gramophones made and developed throughout the 20th century. This machine is of particular interest to the Warrnambool and District Historical Society as it is an Edison phonograph and an earlier model of this phonograph was used in Warrnambool late in the 19th century to make an important recording. In 1896 Thomas Rome, an employee in a Warrnambool boot and shoe shop, purchased an Edison phonograph that could both play and record sounds. At the Warrnambool Industrial and Art Exhibition of 1896-7 visitors to the Exhibition paid a fee to listen to music on this phonograph. But Rome also recorded some local Warrnambool people singing and speaking and these recordings survive today. They are regarded as the oldest surviving recordings made in Australia. Thomas Rome later became a shoe shop proprietor in Warrnambool and was a well-known person in the town/city for a great number of years. This is an Edison Gem Phonograph. It has a black-painted wooden base, now detached from the main mechanism. The phonograph is made of metal which is now heavily rusted. It has a cylindrical turntable for playing the Edison cylindrical records and a handle with a wooden knob. The turning mechanism and belt are now broken. The name of the manufacturer and details of the patents are on a metal plate attached to the side of the phonograph. The amplifier mechanism at the top of the machine is missing. The cover of the machine is made of wood and has a wooden handle attached with a piece of metal and two metal screws. There are also two metal screws on the side of the cover. The cover has a slot on the side to allow the turning handle to be accommodated outside of the cover. The cover is much stained and spotted. ‘Edison Gem Phonograph’ thomas edison, history of sound recordings, thomas rome (warrnambool)

This organ was gifted by the Bethel Community in 1890 to the then Victorian Seamen's Mission, originally founded by the Bethel Union in 1857. The gift was intended to assist with worship. Despite all appearance, this organ is not a pipe organ but a reed organ that works in a similar manner to an accordion. In May 1890, the sum of seventy pounds was put towards the purchase of the organ. The sum being raised via subscriptions. The organ was inaugurated in September 1890. Jabez Carnegie (1832-1892), importer of piano and organs in Melbourne, had made a trip to Europe and Canada in 1887 and had secured the agency of Bell organs. W. Bell & Co were a Canadian organ and piano manufacturer, considered the premier organ manufacturer of the time. W Bell & Co changed its name to Bell Organ and Piano Co in 1888 meaning this organ had to be manufactured prior to the name change. The organ was first used in the mission main room from 1890 to 1915 when the St Nicholas chapel was built at the back (see item 0548. It was transfered to the new Port Melbourne mission in 1937 (link on postcard from State Library Victoria). In 1972, it was transferred to the Holy Trinity Church in Bay Street after the closure of the Mission In the late 1980s during a National Trust campaign to save the building, the organ was sold by the Anglican Men's Society to the Trust's organ committee, who carried out some restoration work and returned it to the former Missions to Seamen chapel. In 1991 the Office of Major Projects had control of the whole 'Bayside' development site. With the Mission to Seamen Building emptied and proposed for demolition, the Office of Major Projects removed the organ and placed it in storage in various locations - finally, in the Museum of Victoria store in Abbotsford. In 1995-6, enquiries by Jim Hillis resulted in the return of the organ to the control of the Port Melbourne HIstorical & Preservation Society. As the Society had no suitable location for the organ, several churches and schools in Port Melbourne were approached to take the organ with no results. The nearby suburbs were suggested next. Finally the Melbourne Maritime Museum (Polly Woodside) was approached and agreed to place it in their Museum on a long term loan. In 1997 it was on display in no 5 shed South Wharf (23/3/1997). In 2006, the Polly Woodside South Wharf site was to be re-developed, and they could no longer retain the organ. Accordingly, on 4 May 2006, the organ was transferred to the Mission To Seafarers building in Flinders Street Extension as an indefinite loan (refer OL 022) The PMHPS deaccessioned it to finally transfered it in 2018 to MTSV.(See also acquisition details re 21st C finalisation of acquisition) This organ is a tangible reminder of the longevity of the Mission to Seafarers, a link with the original Bethel Union which was instrumental in 1856 calling a public meeting and inviting subscriptions by various non-conformist churches to found a mission to Seamen. Rev Kerr-Johnson delivered the first service in 1857 aboard the Emily. The Mission to Seafarers has been in operation ever since and continues to operate to the same purpose today.Large reed organ that looks like a pipe organ with fifteen elaborately painted pipes bearing a floral motif. The body of the organ is elaborately decorated in carved wood. It has 17 knobs above the keyboard both which can be concealed when the keyboard cover is lowered. There are two foot pedals at the bottom of the organ with "Mouse Proof Pedals" cast into the framing iron. list of stop names: Viola 4Ft Diapason 8Ft Dolce 4Ft Violetta 2Ft Sub Bass 16 Ft Octave Coupler Vox Humana Forte Picciolo 2Ft Hautboy 8Ft Aeoline 8Ft Cremona 16Ft E---bone 16Ft Echo 8Ft Celeste 8Ft Melodia 8Ft Flute 4FtMaker's mark in gold lettering above keyboard: W. Bell & Co Brass plaque on front board: Presented to/The Victorian Seamen's Mission/by/Congregation worshipping in Bethel/& friends./1st September 1890 Behind the stops a wooden plaque: J. CARNEGIE & SONS, SOLE AGENTS FOR VICTORIA MELBOURNE organ, worship, bethel, pipes, reed, bethel union, pipe top, jabez carnegie, w. bell & co, port melbourne, mission to seafarers, seamens' mission, mission to seamen, guelph, ontario, canada, pmhps, polly woodside, harmonium, reed organ

This wooden juggling club or exercise club may also be referred to as a juggling pin. It is very similar in shape to a bowling pin or an Indian club. It dates approximately to the early 20th century. It may have been used as one of a pair for gymnastics or exercise, or part of a larger set used by a juggler for entertainment in a circus or carnival. At some time it may have been used with a ball or disc as part of a Skittles or bowling game set. The historical collection of Federation University Australia, Victoria, includes a very similar but slightly shorter club, labelled ‘timber skittle”, as can be seen in their photograph. Another example of very similar-shaped, same-sized clubs can be seen in the collection of Nobelius Heritage Park and Emerald Museum, Emerald, Victoria. JUGGLING Jugglers entertain audiences with their tricks and routines at events such as circuses, amusement parks, parties, shows on television or theatre, schools and parties. Juggles also compete at International Championships to obtain world records, performing as individuals or in groups or teams. Contemporary champion juggler David Cain performs a Juggling History Show that both entertains and educates his audience. His routines date from the early 1600s to the 20th century. He uses a wide variety of equipment in his acts including juggling clubs. EXERCISE Exercise clubs or Indian clubs were used in 19th century Victorian times as part of exercise or strengthening programs when they were swung in certain patterns and movements. Even in the early 20th century workplace a few minutes of Indian club swinging was common practice for the relief of tension. A video clip of an American school room in 1904 shows a group of boys and girls skilfully wielding clubs in an exercise sequence (see ‘Links” section). The 1904 and 1932 Olympic Games had an event called Club Swinging. Rhythmic gymnastics was added to the Olympic Program at the L.A. Games in 1984 where competitors use apparatus such as rope, hoop, ball, ribbon and clubs. The clubs come in a variety of weights and heights and have been used from the mid-1800s until around the 1930s in schools and military institutions. They are decorated in a variety of patterns and colours and some have feature lines or scored rings on them. This juggling club is significant for its association with education, entertainment and sport in the late 19th and early 20th century.Wooden juggling club (or pin, skittle or Indian club). Vintage, bottle-shaped club with a flat, slightly concave, base. Its turned, solid timber body tapers out from the base then in again to a very narrow handle with a round knob joined onto the top. Two concentric feature lines are scored into the wider part of club. It was possibly used in exercise, gymnastics or as a skittle. Sections of the club have two brown painted stripes; paint on the lower strip has been worn off at the base . There are remnants of white paint in two areas, possibly the remains of a maker’s name or decoration. There also appears to be an inscription stamped into the wooden handle but this is illegible. Late 19th to early 20th century.Remnants of what appears to be stamped lettering and painted labelling.flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, wooden skittle, entertainment, bowling skittle, wooden juggling pin, wooden juggling club, wooden exercise club, indian club, exercise club, club swinging, rhythmic gymnastics, sport equipment, juggling equipment, wooden club

Watchmaker History: James McCabe born in 1748 and was the son of Patrick McCabe, a notable watchmaker from Lurgan in County Armagh, Ireland. James McCabe immigrated to London in 1775 where he established his own business in Bells Building, Fleet Street. On 2nd April 1781, James McCabe was made an Honorary Freeman of the Clockmakers Company. The House of McCabe was renowned for the sheer variety of its designs and the creativity and prestige of their manufacture was celebrated and revered by owners worldwide. These pieces remain highly collectable today and fetch increasingly higher prices at auction houses worldwide. Watch association with the Loch Ard: The watch was saved from the sea when discovered on the body of Mrs Rebecca Carmichael from Dublin and handed to Eva Carmichael, the only family member to survive the fatal wreck of the Loch Ard on 1st June 1878. Eva gifted the watch to her husband, Thomas Achilles Townsend when they married in 1884; his name is engraved on the rear movement cover. The watch has been held by the family until 2011 when they decided to bring the watch, to Australia for auction. At this time the watch was in the possession of Eva Carmichael's grandson, Robert Townsend. Given its connection with the Loch Ard shipwreck It was purchased at auction by Flagstaff Hill Maritime Village on 25th October 2011 to add to it's Loch Ard collection and is currently referred to as the Carmichael watch. It is now on display alongside the Minton Peacock, which also survived the Loch Ard shipwreck, and other artefacts from the collection. James McCabe was originally a Belfast watchmaker who had moved his business to London. At the time James McCabe was much esteemed for producing fine watches and clocks, especially for export to India. Only the best watches were inscribed “James McCabe” and many with highly decorated cases were intended for the Indian market. Contemporary newspaper accounts of the watches discovery echoed a Carmichael family tradition that the watch had been intended as a gift from the City of Dublin to King George IV to mark his planned visit to the city in 1821 however there is no evidence to support this theory. Dr Evory Carmichael at some stage bought this watch some accounts say from a nobleman for about £100 and so it travelled with him on his final fateful journey to Australia. Today we can only guess at the actions of Mrs Carmichael in the chaos and darkness of the pre-dawn shipwreck. Perhaps the two items that were found on her body, the watch and a locket, were items that reminded her of those she held most dear, her husband and her family. When Mrs Carmichael's body was washed ashore the watch was found secreted in the waistband of her dress. In its own right the watch is of artistic and monetary value and is a rare and beautiful object depicting watch making in the early 19th century. It is a historically significant object in it’s own right and there is additional importance, surviving a significant event in the maritime history of Victoria. The wreck of the Loch Ard, Victoria's greatest maritime disaster has also been declared an event of National Significance because of its strong connection to Australia's immigration and maritime history. The watch, together with the Loch Ard Peacock, make up the two most significant shipwreck artefacts in Australia. Both of these items are of great social significance to not only local people but the wider Australian community. Funding for the watches purchase came from six local trusts and one anonymous citizen and is now on permanent display. Both these artefacts symbolise and helps to interpret the stories of survival along the Shipwreck Coast. Fob Watch, known as the "Carmichael Watch" or the "Loch Ard Watch". 1814 fob pocket watch belonging to the Carmichael family, recovered from the wreck of the Loch Ard. Fob watch (or pocket watch)and winding key, made by James McCabe and Son, of Cornhill, London. The watch is in excellent condition and its design is decorative and intricate. The gold face is covered by glass. The gold rear cover is hinged over a silver inner cover that includes the winding hole. The watch has a knob with a swinging ring from which it can be hung. The dial of the gold watch face is textured and has raised Arabic numerals and every minute is marked around the perimeter by a dot, with the 5-minute dots slightly larger. The numerals and dots are a different coloured gold than the rest of the face. The centre of the face has a wavy pattern fanning out to the base of the numerals. The hour and minute hands are of a dark colour. The stems of the hands are a wavy shape and finish with spade shaped tips; the tip of the hour hand is larger than that of the minute hand. The hour hand reaches to the base of the numerals and the minute hand is long enough to rest between the minute dots. The back of the watch is decorated with a detailed design on a textured gold background. The design is embossed in coloured metals; gold, silver, greenish-gold and pink. In the centre is a dove resting on leaves of a pot plant that sits on a silver circular base. Another dove is flying above it, and their beaks touch together. On the right of the base of the pot plant is a dog resting on its hind legs, body facing away from the plant and head twisted around to look at the birds. On the sides of this design and meeting at the base are sprigs of leaves and buds. Around this central design is a rope-like border. Around the perimeter of the case is a border of leaves and budding stems. The inside of this cover has embossed hallmarks, numbers and etched markings indicating that the watch is 18 carat gold, made by James McCabe, assayed in London in 1814 and the case may have been made by Daniel Willmott, case maker. The silver inner workings cover has a full name beautifully engraved on it. There is a winding hole that accesses a square-ended lever for the key to fit over. The handle of the watch is a twisted gold knob with a hollow ‘D’-shaped swinging ring attached to the end of it. This knob also has a hallmark.On the silver inner workings cover “Thomas Achilles Townshend” is engraved, underscored by a thin, delicately decorated line. On the gold handle is the logo of a crown with “18”’ next to it. Inside the gold rear case is stamped “DW’. Under that is etched “JAN 77 II”. Underneath this are 3 logos; a logo “leopard, crowned”’, a logo “ crown on top of 18”, and a logo “T”. Under these 3 symbols is part of a stamp that could possibly be “IMC”. Under this is “ ’ 5 9 4 ”. Other numbers, symbols and letters are etched into this case including “15001”, “2/5/19”. Others are difficult to read.warrnambool, shipwrecked coast, shipwreck coast, flagstaff hill, flagstaff hill maritime museum, flagstaff hill maritime village, maritime museum, shipwrecked artefact, shipwreck artefact, carmichael, townshend, townsend, carmichael watch, loch ard watch, pocket watch, loch ard, 1st june 1878, james mccabe, thomas walker, robert townshend, loch ard gorge, great ocean road, victoria., memorial headstone

Cast iron stoves burn solid fuel such as wood or coal, and are used for cooking and warmth. The stoves have a firebox with a grate where the fuel is burned. The hot air flows through flues and baffles that heat the stove top and the oven. Before cast iron stoves were invented, cooking and heating were carried out in outdoor open fires, and later, in fireplaces inside the home. In 1642 the first cast iron stove was manufactured in Lynn, Massachusetts, where molten cast iron was poured into a sand mould to make rectangular plates that were then joined together to make a box. Benjamin Franklin invented the more efficient Pennsylvania stove in 1744, and this efficient design is still used today. After the mid-19th century cast iron stoves were produced with burners in different positions, giving varied temperatures, so a wide variety of foods could be cooked at the same time at the most suitable heat, from slow cooking to baking scones. In contemporary times people the new wood-burning stoves had to meet the anti-pollution standards now in place to protect our environment. By the 1920s gas cookers were being introduced for domestic use, and by the 1930s electric home cookers were being offered to householders. PLANET STOVES In August 1925 the firm Cox and Rizzetti, Stove Works, and also Sydney Road, South Melbourne, advertised in the Brunswick and Coburg Leader of November 11, 1925 as "formerly with Harnwell and Sons" and as "specialists in solid cast iron Planet stoves ... which merit an inspection from builders and householders". The firm continued in business and was mentioned as sponsors in the King Island News in 1971. Harnwell and Sons was listed in the Victorian Government Gazette of 1894. It is curious that the firm was mentioned in an article in the Sunrasia Daily of June 14, 1934 titled 'Planet Stoves' as a manufacturer of Planet Stoves. This Planet No 3 stove is an uncommon example of cooking equipment used in kitchens in the early 20th century, as the firebox is above the oven rather than beside it. The cast iron combustion stove is significant as part of the evolution of domestic cooking. Previously cooking was mostly carried out in outdoors in open fires, and later in fireplaces indoors. Cast iron stoves are still used today and have additional features such as thermostats to monitor and maintain temperature, water heating pipes connected, and environmentally approved anti-pollution fittings. Stove; a compact, blackened cast iron combustion cooker, installed within a fireplace and enclosed by bricks on both sides. The upright rectangular stove has a flat top with three round, removable cook plates and a flue connected at the back. The front has three doors with round knob handles; a swing-down firebox door above a sliding ashtray, and two side-hinged oven doors above a sliding opening. Inside on the side walls are two pairs of runners. Behind the pair of doors is an oven with two pairs of rails and two removable metal shelves. The stove has cast inscriptions on the chimney flue and on the front of the right hand side stove door. The model of the stove is The Planet No 3, made in Melbourne.Chimney flue, "[within rectangle] THE / PLANET" Stove door, "(within oval) PLANET / No 3"flagstaff hill, flagstaff hill maritime museum and village, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, stove, cast iron stove, combustion stove, wood-burning stove, wood stove, wood oven, solid fuel stove, cooker, the planet, planet, planet no. 3, kitchen equipment, baking, domestic cooking, cooking equipment, food preparation, planet stove, planet cooker, cooking range, slow combustion stove, antique, range cooker, cox and rizzetti, harnwell and sons, melbourne manufacturer

Six walking canes shaped from natural timber. 7543a Light coloured wood with top carved in shape of a snake head. 7543b Light brown wood with T shape carved top. 7543c Dark brown branch with bark intact. Natural branch at 30 degrees cropped at top. 7543d Thin dark brown bamboo like straight walking stick. Ornate carved knob at top. 7543e Light brown straight walking stick of three pieces of wood spliced together. Curved top spliced in place. Lacquered and polished. Metal band attached below hand grip (1.5 cm wide.) 7543f Rough natural branch with natural handle at 30 degrees angle.walking sticks, wooden objects, natural wood

Hand theatre made "trench art", utilising used artillery brass shell casings, of various calibres, hand made with such "tools" as were available at the time. They have been decoratively trimmed at the mouth of each with a "scalloped" pattern, the shallowest casing mounted on small arms casings as "feet" and the large casing inverted engraved and embossed with a depiction of the Australian Commonwealth Military Forces "Rising Sun" badge.This "Dinner Gong" and "Striker" are significant Historically and Socially, as it is believed to be the only example of a dinner gong and striker made in theatre as contemporary "trench art" by serving members of this group. Around the top of the main part of the Gong are stamped the initials of the Australian members of the Royal Flying Corps at the time, it is of possible National historical significance, as they were such a small group at best, and a highly vulnerable group, quite likely to not survive the conflict. This group and their desendants went on to be a part of the formation of the Australian Flying Corps, the beginings of the Royal Australian Air Force. It relates to the embrionic stages of a part of the now Australian Defence Force.A commemorative Dinner Gong construted from Artillery Shell Casings of various sizes. The largest cut short at the bottom, mounted on rifle or machine gun casings cut short as 'feet'. A slightly smaller diameter inverted as the 'gong' with decorative engravings depicting, a Rising Sun emblem on a decorated back ground, 'AFC' (Australian Flying Corps) crowned wings, on the same decorated back ground. The open ends of these larger casings is 'scalloped' and decorated beautifully, while the closed ends have a 'pie crust effect around the flanged edge. There is a biforcated mount at the top to hold the 'striker' made from white metal ballastered rod with a wooden eliptical knob. On the top around the striker mount are stamped the initials of those believed to be the first Australian Aviators in the then AFC.

This magic lantern or slide projector was used to project glass slides on to a screen The magic lantern was the chief visual entertainment for the public before the introduction of the moving picture and consequent cinema entertainment. This one probably dates from about 1915 but its provenance is not known.This magic lantern is an important and interesting object as it shows us the way people in the early 20th century were entertained. The few people who owned this type of projector would give public showings of slides of people and scenes and sometimes raise money for a charitable cause in this way. This is a glass slide projector or magic lantern with a rectangular metal lantern body partly open at the back. The back has a top section that is attached with a metal hinge and lifts up and outwards. The lantern base also has a side opening with a metal knob for opening and a metal panel with a blue glass inset. Inside the lantern body is the lamp and an electric cord (the illuminant system may have originally been fuelled by paraffin or another oil burner). On top of the lantern body is a smaller rectangular metal box in two sections. This can be removed. The illuminant system is brass and slides out. It has two mechanisms for adjusting the focus and a covering over the lens opening which can be pulled up. There is also a wooden slide holder which can be pulled in and out of the projector. ‘W.B. British Made’ social history, history of warrnambool, glass slide projector

Arthur E. Woodley donated the WW1 Military Carbide Signal and General Purpose Lamp to Frankston RSL. It was given to Arthur E. Woodley of Crib Point during the 1960s by Captain Ivan E. Layton MBE who was then the Executive Officer of Melbourne Legacy. During WW2 Ivan Layton was secretary to General Blamey. Ivan Layton died on 15th September, 1979. The carbide workings of the lamp were removed because of corrosion, otherwise it is almost complete.WW1 Military Carbide Signal and General Purpose Lamp which is round and made of brass. The lamp has a latched and hinged brass top. Brass and wood hinged handle with knurled access knob which is situated at the top of the lamp. In between the handle uprights is a round chimney flu which allows heat to escape. Approximately one third down from the top of the lamp there is a brass side handle. Immediately to the left of the handle is a rectangular curved view port with brass cover. Directly opposite the side handle is a convex glass window. Air vents are located at the bottom of the lamp. Inside the top half of the lamp is a chamber which contains the carbide lamp and perpendicular sleeves for the insertion of coloured glass panels. The bottom half of the lamp contains the carbide.Manufacturers Stamp, 'PLAYER & MITCHELL LTD', 'SENTINEL WORKS' 'BIRMINGHAM'ww1, military, brass, lamp, world war 1, round, great war, carbide, signal lamp, player mitchell, birmingham

Cast iron dolly pots were used in the mining industry to crush ore specimens and samples into dust before panning. The principle is the same as a mortar and pestle.This item has two pieces both are made from cast iron and are rusted and a dark brown color. One is a tapering cylinder 16.5 centimetres wide a its top, the first two and a half centimetres down tapper to 13.5 diameter, the next nine centimetres tapper to 11 centimetres diameter. the last two and a half centimetres is a solid base that flares out to a 16.5 centimetre diameter, the inside of the bottom of the cylinder is a bowl shape. The other piece is a solid tapering shape, it's four and a half centimetres in diameter at one end which tappers to three centimetres in four centimetres of length, the next sixteen centimetres tapper to two centimetre diameter. There is a knob on top, one and a half centimetre high and two and a half centimetres wide.mortar and pestle, dolly pot, gold minning

There is a brass plaque that states: THIS PLAQUE IS IN MEMORY OF DORA CHAPMAN daughter of William and Estelle Chapman CALLED HOME WHILE PLAYING THE ORGAN ON THE OCCASION OF THE 30TH ANNIVERSARY OF THE SILVAN CHURCH. SEPTEMBER, 27TH 1936 DORA WAS A SISTER TO MR ERNEST CHAPMAN On another plaque it states: THIS ORGAN WAS A WEDDING PRESENT TO ERN AND BERYL CHAPMAN AND WAS DONATED TO MONT DE LANCEY IN THE YEAR 1994 BY MAVIS, BOB, LES AND ALBERT CHAPMAN The organ was a present from Mr Ernest Chapman and his bride on the occasion of their wedding on October 26th 1927. The organ was made in Meriden Connecticut USA by Wilcox and White in 1885. A date inside the organ indicates that it was last tuned June 16th 1900. A highly decorated, delicate ornate carved wooden pump organ with a round mirror set back into the front panel. It has a sheet music rest or shelf with an opening lid to store sheet music inside the cupboard. There are two side shelves with five knobs on each at the front. It has a keyboard with thirteen stops below. Next to the key stops above the keyboard is gold lettering with 'Wilcox & White Meriden. Connecticut. USA.There are two brass patterned pump foot pedals below: the left one has 'WILCOX' stamped on it, the right pedal has '& WHITE' stamped on it and the metal is damaged from use. There are two carved levers underneath the keyboard: the left one has a sticker saying "Grand Organ", the right one's sticker says, "Knee Swell". There is no stool.The brass covered left foot pump pedal has 'WHITE' stamped on it, the right pedal has '......' stamped on it. There are two carved levers underneath the keyboard: the left one has a sticker saying 'Grand Organ', the right one's sticker says, 'Knee Swell'. The manufacturer : WILCOX AND WHITE is printed in gold letters on ......The thirteen 'stops' all have different musical terms printed in a sticker. e.g...............parlour organs, cabinet organs, harmoniums, pump organs

The Optacon OPtical-to-TActile-CONverter is a compact, portable reading aid for the blind. It is about the size of a textbook, and weighs less than 2kg. It works by converting a printed image into a tactile image that a blind person can feel with one finger. After a period of training and practice, a blind person can use the Optacon to read ordinary books, magazines, newspapers, and other printed materials. The Optacon was developed after intensive research at Standford University, California, USA and was trialed by clients of the Royal Victorian Institute for the Blind (now part of Vision Australia) in 1973. It has three main sections: 1 a miniature camera, 2 an electronics section, and 3 a tactile stimulator array. The miniature camera, about the size of a pocket knife, is mounted in a housing that has rollers for easy movement along a line of print. The camera is connected to the electronics section by a lightweight cable. The electronics section and the tactile stimulator array are in the main chassis. The array consists of 144 tiny metal rods arranged in six vertical columns and 24 horizontal rows. Each of the rods can vibrate independently. The tips of these rods protrude through holes in a concave finger plate where the index finger is placed flat in order to read. These three components act together to convert the image of a printed letter or other shape into a pattern of vibrating rods, a tactile image of the letter or shape. The letter shape is tactually perceived as an image that moves from right to left on the finger, showing the left or leading edge of the letter first. Letters are felt sequentially rather than all at once, and the image should be kept moving. The Optacon converts a printed O into a tactile form that resembles a crater with a vibrating rim -- a completed circle. C would have a gap or opening on the right side of the curve. The letter F would be felt, sequentially, as a vertical line with two trailing horizontal lines. Because it can convert any ordinary printed image into a corresponding tactile image, the Optacon is not restricted to any special typestyle or language. The camera has a zoom lens that compensates for differences in the size of type. The standard Optacon lens can accommodate type sizes from 6 point to 20 point. With the optional F4A magnifier lens, type sizes as small as 4 point can be read. Powered by a rechargeable battery, and comes with its own battery charger. The battery is contained within the main chassis, and is not removable by the user. There are four basic controls on the Optacon: the Magnification Adjustment zoom button located on the camera section on the side opposite the rollers; and the On-Off switch, the Stimulator Intensity Adjustment knob, and the Threshold Adjustment knob located on the right side of the front panel. The Circuit Breaker protrudes from the right-hand wall inside the chassis compartment. From left to right when the back panel is facing you, are located: the jack for connecting the battery charger; the Battery Check button; the Normal-Invert switch; and the Input/Output I/O connector for use with the Visual Display, when using the Repeater Cable to connect two Optacons to one another or with other accessories. Designed not be removed from the leather case during normal operation, the On-Off switch is a slide switch located on the right side of the front panel. It slides up and snaps into place in the on position. 1 black with orange front, rectangular device in leather case assistive devices, audio equipment

This is a set of eight photographs of technicians operating photogrammetric equipment in Air Survey Squadron, Army Survey Regiment, Fortuna, Bendigo. c1960s to c1980s. The Wild A9 Stereocomparator and Wild B9 stereo plotter were introduced in 1962. The Wild B8 stereo plotter was introduced in 1966. Technicians used the Wild A9 Stereocomparator to accurately measure between pass, tie, and survey control points on aerial photographs. The Wild B9 and B8s were used for plotting topographic detail and contours. These analogue machines were manually controlled by adjusting the control knobs for the orientation of the 3D image. The B9s used a four and a half square, and the B8s used a nine-inch square photo image on a film or glass diapositive which allowed highly accurate extraction of map features. At first, plotting with B8 and B9 stereo plotters was undertaken at the aerial photography scale of 1:80,000 in pencil onto a controlled plotting sheet. Sheets were then inked up and reduced photographically to the 1: 100,000 publication scale for scribe impression production. In the early days topographic detail and contours were plotted with a pencil or ink pen mounted at the far end of the pantograph arm. The plotting procedure was upgraded to direct plotting in ink with photographic reduction to publication scale. In 1975 four B8s were upgraded with tri-axis locaters as part of the Input Sub-system to enable digital extraction to AUTOMAP 1’s topographic database. When AUTOMAP 2 was introduced in 1982 these B8s were upgraded, and additional machines added to expand the Army Survey Regiment’s digital capture capability. This is a set of eight photographs of technicians operating photogrammetric equipment in Air Survey Squadron, Army Survey Regiment, Fortuna, Bendigo. c1960s to c1980s. Black and white and colour photos are on photographic paper and scanned at 300 dpi. .1) - Photo, black & white, c1965. Unidentified technician operating a Wild A9 Stereocomparator. .2) - Photo, black & white, c1965. Unidentified technician operating a Wild B9 stereo plotter. .3) - Photo, black & white, c1967. L to R: Unidentified technician, SPR Ken Jeffery operating a Wild B9 stereo plotter. .4) - Photo, colour, c1974. Unidentified technician, operating a Wild B8 stereo plotter. .5) - Photo, black & white, c1974. Unidentified technician operating a Wild B8 stereo plotter. .6) to .7) - Photo, black & white, c1979. Unidentified technicians operating a Wild B8 stereo plotter. .8) - Photo, black & white, c1985. Unidentified technician in AUTOMAP 2 operating a Wild B8 stereo plotter..1P, .2P, .4P, .5P, .7P – no annotations. .3P – annotated ‘Standing - , Seated SPR Ken Jefferies (sic). .6P – annotated with date ‘1979’ .8P – annotated ‘AUTOMAP 2’royal australian survey corps, rasvy, army survey regiment, army svy regt, fortuna, asr, air survey, photogrammetry

The teaspoon is a European invention. Small spoons were common in Europe since at least the 13th century; the special spoons were introduced almost simultaneously with tea and coffee. (Pettigrew points to its use in the mid-17th century.) Originally the teaspoons were exotic items, precious and small, resembling the demitasse spoons of later times. Also used for coffee, these spoons were usually made of gilt silver, and were available with a variety of handle shapes: plain, twisted, or decorated with knobs, also known as knops, hence the knop-top name for such spoons. Widespread use and the modern size dates back to the Georgian era. The teaspoon is first mentioned in an advertisement in a 1686 edition of the London Gazette. Teaspoons, probably of English origin, are present in the 1700 Dutch painting by Nicholas Verkolje, "A Tea Party". An 1825 cartoon makes fun of a Frenchman unfamiliar with the British etiquette. The guest did not place his spoon into the cup and is thus being offered his thirteenth cup of tea! A special dish for resting the teaspoons, a "spoon boat", was a part of the tea set in the 18th century. At that time, the spoons played an important role in tea drinking etiquette: a spoon laid "across" the teacup indicated that the guest did not need any more tea, otherwise, the hostess was obligated to offer a fresh cup of tea, and it was considered impolite to refuse the offering. Pettigrew reports that sometimes the spoons were numbered to make it easier to match the cups with the guests after a refill. https://en.wikipedia.org/wiki/Teaspoon#:~:text=Teaspoon%20is%20a%20European%20invention,the%20mid%2D17th%20century).A history of the teaspoon.Metal teaspoon, badly corrodedNoneflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

The two‐door cabinet with a bench top is a simply made nineteenth century utilitarian cupboard. It is similar in style to cupboards that were built into spaces either side of fireplaces in keepers’ quarters. All have two doors simply framed around recessed central panels, which are sometimes bevelled. They are opened with a key, or by a basic knob made of metal or turned wood. Most also are made from a light‐coloured wood, which in this case is possibly Huon pine. Some are painted, others show evidence of paint which has since been removed in an effort to restore the surface, and a few retain their original wood finish. This cabinet, which has plain recessed unbevelled panels, has one internal shelf and stands on the floor without a plinth base. The bench top has basic squared edges, and a low backing with curved ends extends around one side. These features suggest the cabinet was fixed and originally built into a corner. The Cape Nelson CMP identified a similar but slightly different cabinet in one of the assistant keepers’ quarters which is shown with shelves added to the top. Other similar two‐door, benchtop cupboards that were probably built‐in include those at Cape Otway and Cape Schanck , which have since been moved out of the residences. Built‐in cabinets were standard fittings in lightkeeper quarters as illustrated by the Point Hicks Lightstation CMP, which shows a built cupboard beside a fireplace. The Cape Nelson cabinet, an original domestic furnishing provided by the Public Works Department, has first level contributory significance for its historic values and provenance to the lightstation.Two‐door cabinet with a bench top. The doors are simply framed around recessed central panels.Light coloured wood.

The inclusion of 2 Turkish buttons and the possibility of the belt itself being Turkish seems to indicate that the belt was obtained at Gallipoli. As some of the other badges and buttons are not of Australian origin, the indication is that they were traded during the owner's service.This item is significant in that it has original badges and buttons from uniforms of WWI. The person to whom this belt belonged obviously served at Gallipoli and returned from active service. brass button bearing the insignia of artillery, 2 brass buttons bearing a crescent and star, 1 bearing the outline of Australia with a crown above, 1 plain copper button and 1 brass button bearing the picture of a hand grenade.Belt: Webbing, 2 metal buckles with 2 leather ends and tongues and a leather pocket stitched 7.5 cm from the tongue end. 29 cm from the buckle end there is what is possibly a leather canteen hook, 2 cm wide, 17 cm long, with a copper escutcheon which hooks over a brass knob . Three stripes, top and bottom stripes blue, middle stripe khaki. Pinned to the buckle end of the belt are 5 copper badges: INF / RGA / / 4 / LH and a small crown and 3 brass badges TYNESIDE / 4 / SCOTTISH. On the tongue end are 2 brass buttons embossed with crowns, 1 world war one, anzac, ww1, gallipoli, badges, buttons, uniform belt, turkish uniform, turkish, british badges, tyneside scottish

This kettle was made in the 1880s.Cast iron kettle 16 centimetres diameter at its base and 18 centimeters diameter at its widest point 11 centimeters above the base, it then curves up another three centimetres where there is a ten centimetre diameter hole. A non-matching metal lid with a one and a half centimetre knob covers the hole. Three centimetres from the base of the kettle there is a two and a half centimetre diameter spout which tappers to one and a half centimetres, it's 14 centimetres long and has two bends. A handle is attached to the top of the kettle, it is two centimetres wide, it extends two centimetres straight up at both ends that are 12 centimetres apart then forms an open oval 20 centimetres wide and nine centimetres high, it's one and a half centimetres thick for 11 centimetres at the top and has groves for fingers on the under edge.K23.1kettle, cast iron

This is a set of 14 photographs of RA Svy technicians operating photogrammetric equipment in Air Survey Squadron, Army Survey Regiment, Fortuna, Bendigo; and the School of Military Survey Bonegilla c1960s to c1980s. The Wild B9 stereo plotter were introduced in 1962 and the Wild B8 stereo plotter was introduced in 1966. The Wild B9 and B8 stereo plotters were used for plotting topographic detail and contours. These analogue machines were manually controlled by adjusting the control knobs for the orientation of the 3D image. The B9s used a four and a half square, and the B8s used a nine-inch square photo image on a film or glass diapositive which allowed highly accurate extraction of map features. At first, plotting with B8 and B9 stereo plotters was undertaken at the aerial photography scale of 1:80,000 in pencil onto a controlled plotting sheet. Sheets were then inked up and reduced photographically to the 1: 100,000 publication scale for scribe impression production. In the early days topographic detail and contours were plotted with a pencil or ink pen mounted at the far end of the pantograph arm. The plotting procedure was upgraded to direct plotting in ink with photographic reduction to publication scale. In 1975 four B8s were upgraded with tri-axis locaters as part of the Input Sub-system to enable digital extraction to AUTOMAP 1’s topographic database. When AUTOMAP 2 was introduced in 1982 these B8s were upgraded, and additional machines added to expand the Army Survey Regiment’s digital capture capability. There are several more photos catalogued in the Victorian Collections database of RA Svy personnel operating Wild B9 and B8 stereo plotters.Photogrammetric Equipment – Army Survey Regiment, Fortuna, Bendigo c.1981. . .7) – Unidentified technician operating Wild B8 stereo plotter in AUTOMAP 1 at ASR. .8) - Wild B8 stereo plotter in AUTOMAP 1 at ASR. Photogrammetric Equipment – Army Survey Regiment, Fortuna, Bendigo. c1981. .9) – ASR’s CPL Dave Cook in AUTOMAP 1 operating a Wild B8 stereo plotter. This is a set of 14 photographs of RA Svy technicians operating photogrammetric equipment at the Army Survey Regiment (ASR), Bendigo and the School of Military Survey (SMS) Bonegilla. c1960s to c1980s. The photographs are on 35mm colour slides and were scanned at 96 dpi. .1) - Photo, colour, c1964. Unidentified ASR technicians operating analogue Wild B9 stereo plotters. .2) - Photo, colour, c1974. ASR’s SPR Mick Minchin operating an analogue Wild B8 stereo plotter. .3) to .6) - Photo, colour, c1980. Photogrammetry Instructor SGT Neil ‘Ned’ Kelly at the SMS operating an analogue Wild B8 stereo plotter. .7) - Photo, colour, c1981. Unidentified technician operating Wild B8 stereo plotter in AUTOMAP 1 at ASR. .8) - Photo, colour, c1981. Wild B8 stereo plotter in AUTOMAP 1 at ASR. .9) to .14) - Photo, colour, c1981. ASR’s CPL Dave Cook in AUTOMAP 1 operating a Wild B8 stereo plotter..1P to .14P - Some of the equipment is annotated on the frame of the 35mm slides.royal australian survey corps, rasvy, army survey regiment, army svy regt, fortuna, asr, photogrammetry

The tall, two‐door cupboard with curved shelves is without a back and is taller than the bench cupboard on the lower lantern room of the lighthouse . The curved shelving suggests that this practical storage cupboard was custom‐built or adapted to serve in this location on the landing level below the lantern room. It is not known when it was provided to the lightstation. It shares the structural features of this furnishing as well as other nineteenth century utilitarian cabinets that were made for Victoria’s lightstations, such as those fitted beside fireplaces in the keepers’ quarters (for example CNLS 0016) or serving as lantern room cupboards. They have doors simply framed and bevelled around central panels. This particular cupboard, which is painted grey with four white panels, is unusual both for its height and the four doors, with the twin top panels taller than those underneath. This panel arrangement repeats the design of the lightstation’s door cases. Further research may reveal more about its manufacture. It is not known whether it is attached to the wall or movable; if attached it is considered to be a fixture and included in the Victorian Heritage Register listing for the lightstation (VHR H1773). Other similar cabinets which have been constructed to fit the curved wall of a lighthouse survive at Cape Schanck, varnished wood benchtop, 2‐door cabinet with brass door knob, no drawers); Point Hicks, benchtop, 2‐door, painted green with silver doors, no drawers) and Gabo Island bench top, 2‐door, no drawers, green paint removed to reveal cedar timber), and Cape Nelson, benchtop, 2‐door, 2‐drawer, partially varnished). Cape Nelson’s tall cupboard with curved shelves and back profile is unusual among the lighthouse furnishings. The cabinet is a unique, original feature of the lighthouse and has first level contributory significance for its historic values and provenance.The tall, two‐door cupboard with curved shelves is without a back and has curved shelving. Painted grey with four white panels, on the four doors, with the twin top panels taller than those underneath.