Cast iron shoe last broken fromNil triple stand

098?? stamped on instep. Removable instep cast ? 241 on foot cast with locating grooves for instep cast. Locating hole on under foot arch

Cast iron shoe last with instep slide slide and grove No instep mould(*9 on upper toe, 2 cast indentations on outside of foot, 1 on inside of foot, 1 on upper toe, 2 on sole of foot

Pointed toe, instep slide, instep groove on foot space, general dust and grime.6/DD on toe2 cast hole on out foot, 2 cast holes on sole, various small cast faults

cast iron shoe ;ast12 stamped on foot, 2 cast marks on sole of foot

Small foot shoe last with instep slide and groove in foot space. piece missing in cast in instep slide in foot space. 2cast holes on sole. dirty and dusty12 cast on toe

Cast iron shoe last with instep slide and instep grove in foot space6 DD on toe, 2 cast holes on sole, 1 cast hole on upper toe, 2 cast holes on right bunion side

Carved pale wooden toe. Stiff metal spring. Unsealed wooden ball at heel end1/325/3on inside of toe carving

Carved wooden heel extensions with inverted slide on one side and locating slide on other sideL and R stamped on each. Left extension 9 1/2(half) / 3 on inverted slide written in pencil. 16 written on locating slide in pencil Right extension 9 1/2(half) /3 on inverted slide written in pencil. 15 written on locating slide in pencil tied together with orange thread through brass rings

Wooden pattern used to make impression in sand to form mold for casting hot metal. These patterns were for the caps for bearing covers.Wood, with an oval footprint. Pins underneath with covered channel across oval, cylindrical cap mounted on top of channel, semi-circular (approx) flanges either side of channel cover.

Wood, cylindrical base, curved narrowing neck, sperical (approx) top; nail hammered diagionally through top.

Two slightly different wooden patterns for casting unknown item. (approx.) Rectangular piece of wood with a narrower piece affixed across top ( long side of rectangle); narrow piece has two curved 'wedges' attached (one loose).

It is unknown what this item was a pattern for.One flat piece of rectangular wood with a hole on the top - center and two nails, one at the top left corner, one at the bottom - RH corner. A second piece of wood is attached on top of the first; it is smaller in width and split exactly in two. There is a design cut out of second piece in shape of a pear. Bulbous part of design is centered around a hole in the first piece of wood. Three nails protrude from the second piece of wood. Three nails in the second piece of wood are located; one in each section of the more bulbous end of cut-out, & third on one section of the smaller end of cut-out. Hole on bottom of wood does not go all of the way through.

This is a pattern for the stove front for the oat kiln at the mill.Rectangular piece of wood, broken at one end with two full cutouts and part of third. One, and the part of another cut-out is high arches. Frame, missing in places, running along outer rim and along cut-outs. Two rows of nails run down between arches holding braces in palce on back.

Used to make cast for the metal ring gear for the water wheel which powered the Mill.Slightly arched wooden pattern with wooden ridges along the edge. Three square metal plates with a hole in the centre, bolted on with four bolts. Ten pentagin pieces of wood attached to the face.

Used as pattern to cast crown wheel of drive on water wheel. Actual drive has since been sold, only mold remainsCircular wooden pattern, raised centre circular area surrounded by four wide, flat spokes at regular intervals (the interim spaces being cut out with rounded corners) which are in turn surrounded by a rim which tapers back from the centre of the piece and has fixed to it regularly interleaved slats. Slats of protruding oblongs tapered from attachment to top and also central end to outer point. Light coloured wood 1 & 2 are Broken off pieces of back.

Attaches to a tap, used in the milling process. (some taps are still intact in the mill building.)Long cylindrical metal hose which gets narrower near the tip. attached to a long canvass hose.

Used to drill railway sleepers in the early 20th Century.'Jigger" - an antique steel large two piece drill used to drill railway sleepers around the early 20th Century. The 50cm drill piece can be detached and replaced and it has a handle with a knob on top to turn the drill. The drill is attached by a bolt and screw.steel, metal, tool, drills

Used by the Ockwell family in the late 19th centuryAn 'M' toothed steel hand saw used to saw rough wood or cross cut wood. It has a wooden handle which is rivetted on with four brass rivets. It was used in the late 19th Century.hand tools, woodworking tools, carpentry tools, wood, steel, hand saws, saws, cutting tools

Made approximately 1890An all steel docking saw with a rough toothed blade used to saw rough wood. The steel eight hole decorative patterned handle is rivetted on with two steel rivets. hand tools, woodworking tools, carpentry tools, steel, hand saws, saws, cutting tools

Used in the late 19th century.A steel bladed wooden curved handled Shingle Splitter sometimes called a Paling Knife used for splitting or cleaving timber. It has two crossed hammer shape symbols stamped at the beginning and end of the inscription - Wolpin Wedge Mills. It was used in the late 19th century.Wolpin Wedge Millssteel, wood, froes, cleaving axes, axes, cutting tools, hand axes, woodworking tools

Used in the 19th or early 20th century.A steel forged metal headed broad axe with a turned wooden handle for a right handed person's use. It was used to trim posts or logs in the 19th or early 20th century.axes, cutting tools, hand axes, froes, woodworking tools, cleaving tools

A Peg tooth forged steel crosscut saw with two wooden handles bolted on. It was used to saw rough wood or cross cut wood against the grain. It was used in the late 19th Century.hand tools, woodworking tools, carpentry tools, wood, steel, hand saws, saws, cutting tools, crosscut saws

Used by Edgar R Sebire.A Peg tooth forged steel crosscut saw with two wooden handles bolted on. It was used to saw rough wood or cross cut wood against the grain. It was used in the late 19th Century by Edgar R Sebire.hand tools, woodworking tools, carpentry tools, wood, steel, hand saws, saws, cutting tools, crosscut saws

A forged steel fine tooth crosscut saw with no handles. There are four rivet bolts and two round handle holders at each end of the saw. It was used to saw rough wood or cross cut wood against the grain in the late 19th Century.hand tools, woodworking tools, carpentry tools, steel, hand saws, saws, cutting tools, crosscut saws

Used by Wandin T SebireA forged steel 'M' toothed crosscut saw with wooden handles bolted on. It was used to saw rough wood or cross cut wood against the grain in the late 19th Century.'W' is stamped on the blade.hand tools, woodworking tools, carpentry tools, steel, hand saws, saws, cutting tools, crosscut saws

Used in the 19th century.A forged steel narrow bladed double Peg and Rake toothed crosscut saw with no handles. It was used to saw rough wood or cross cut wood against the grain in the late 19th Century.Stamped on the saw: made of Simond Steel, Trade mark Reg. Warranted The Simond Saw Est 1832, Simond Steel & Saw co USA. Crescent Ground Steel Mill, Lockport New York. Factories Fitchburg Mass, Montreal Quebec No 325hand tools, woodworking tools, carpentry tools, steel, hand saws, saws, cutting tools, crosscut saws

Used in the 19th century.A curved wooden handled adze with a forged steel head which has a wide cutting blade and a small 5cm steel knob on top. It was used by woodworkers for cutting and trimming rough wooden planks and shaping ans smoothing wooden surfaces in the late 19th century.woodworking tools, wood, steel, froes, cleaving axes, axes, cutting tools, hand axes, adzes

Used in the 19th century.A forged steel broadaxe head without a handle - it has a hole for the handle. It can be known also as a trimming axe blade or a long bearded axe because of its beard shape. It was commonly used in manufacture of square timbers for wooden shipbuilding, log building, timber framing and railroad ties. It was used in the 19th century.woodworking tools, steel, froes, cleaving axes, axes, cutting tools, hand axes, broadaxes, felling axes, hewing axes, axe heads, tool components