Plan (copy) of New Chum Line of Reef. Plan has been copied in two sections. On top of plan 'Underground survey of mines Sandhurst, New Chum Line of Reef', plan shows longitudinal and cross section views of the workings on the reef. Shaft No. 76 marked. Datum line on top indicates 750' above sea level, on bottom of plan, bottom of shaft 2022.24 below sill. Drawn by Arthur Everett, Mining Department, Melbourne, 1884.bendigo, mining, new chum line of reef

Specification or Tender Document - titled "Design, Manufacture and delivery of 100 only all-electric trams", and "Background Information and Preliminary Specification", dated June 1965. Bound into a brown foolscap card cover. Details the conditions of tender, conditions of contract, notes, specification, gives background information about Melbourne, dimensions, performance, drivers and conductors, trucks, wheels, brakes, electrical equipment, control panels and drawings. The drawings give a map of the system, typical city route, Glenferrie Road route (grade diagram), concrete track construction, min. radius curves, loading gauge, all-electric tram and mounting details for the trolley base, schedule of prices, tender form, form of contract, schedule of information to be provided by the tenderer. Comprises: 1 - Conditions of Tendering - 1 page 2 - Conditions of Contract - 4 pages 3 - Contents - 3 pages 4 - Notes for prospective tenderers - dated June 1965 5 - General nature of contract - 21 pages 6 - Appendix A - climate data - two sheets 7 - List of 14 appended drawings 8 - O.6887A - cross section of trolley wire 9 - P.13855 - Glenferrie Road, Longitudinal Section 10 - P.13856 - Wattle Park Route 11 - P.13857 - East Preston Route 12 - P13858 - Concrete track construction 13 - P13859 - Open track construction 14 - P.13860 - Paved ballast track construction 15 - P.13887 - Tram Route - locations of substations and section switches 16 - P.13888 - Minimum radius service curves to give minimum clearance between tramcars 17 - P.13889 - Grooved Rail - 102 pounds per yard and tire profile 18 - R10-301 - Loading gauge, proposed electric tramcars 19 - R9706K - Rolling stock data, tramcars 20 - R10306 - Collins Points Shifter - Wiring diagram. 21 - Schedule of data to be supplied by the tenderer 22 - notes on Automatic Points shifters - 2 sheets 23 - Tender prices and delivery periods - 2 sheets. See Reg Item 2266 for the 1972 version and 1583 for the August 1966 version. See Reg Item 4049 for associated newspaper cuttings. See file htd4667i1.pdf for scans of the drawings.In ink in top right hand corner - "Lees"trams, tramways, specification, tenders, z class, mmtb, melbourne

Whisky came in bottles sold at licensed premises either locally or in larger cities visited during shopping expeditions. The shape of bottles varied. Bottles were recycled remaining the property of the manufacturer who paid for their return. History of James Dickson Co. Pty. Ltd.Historical: Change of Bottles - shape, glass, embossing. Collected by bottle collectors. Aesthetic: Display showing embossing and shapeClear glass whisky bottle with heavy embossing on one side where the maker's name and details is printed in capital letters longitudinally. Heavily embossed zig zag pattern at the top of straight sides that go three quarters of the way up. The sides taper to the neck which has straight sides to the screw top opening. The tapered section is grooved with ridges of straight lines to a lip which is between it and the neck. Side (longitudinally): 'This Bottle is the Property of / James Dickson & Co. Pty Ltd / Established 1854 / Melbourne Aust. / And Cannot Be Legally Used By Others' Base: 'A' above 'F892' and 'M' beneath. Reading from the inside of the bottle on the base is 'E41' whisky, bottle, spirit, james dickson co. pty. ltd

A honing steel, sometimes referred to as a sharpening steel, whet steel, sharpening stick, sharpening rod, butcher's steel, and chef's steel, is a rod of steel, ceramic or diamond-coated steel used to restore keenness to dulled blade edges. They are flat, oval, or round in cross-section and up to 30 centimetres (1 ft) long. The steel and ceramic honing steels may have longitudinal ridges, whereas the diamond-coated steels are smooth but embedded with abrasive diamond particles. Non-abrasive honing rods such as smooth ceramic or ribbed steel are able to remove small amounts of metal via adhesive wear. In normal use, the rod is applied to the blade at a slightly higher angle than that of the bevel, resulting in the formation of a micro-bevel. The term "hone" is associated with light maintenance performed on a blade without the effort and precision normally associated with sharpening, so the name "hone" was borrowed. In the 1980s, ceramic abrasives became increasingly popular and proved an equal, if not superior, method for accomplishing the same daily maintenance tasks; manufacturers replaced steels with ceramic (and later, manufactured diamond abrasive) sharpening "steels" that were actually hones. Use Honing steels are used by lightly placing the near edge of the blade against the base of the steel, then sliding the blade away from yourself along the steel while moving it down – the blade moves diagonally, while the steel remains stationary. This should be done with the blade held at an angle to the steel, usually about 20°, and repeating on the opposite side at the same angle. This is repeated five to ten times per side. Steeling It is often recommended that steeling be performed immediately before or after using a knife and can be done daily. By contrast, knives are generally sharpened much less frequently. A traditional smooth honing steel is of no use if the edge is blunt, because it removes no material; instead it fixes deformations along the edge of a sharp blade, technically known as burnishing. There has long been speculation about the efficacy of steeling (re-aligning the edge) vs honing (removing minor deformation with abrasives); studies tend to favour abrasives for daily maintenance, especially in high-carbide-volume "stainless" steels (such as the popular CPM S30V steel, which tends to "tear out" when steeled rather than re-forming an edge.) Small honing steel for outdoor activities Usage trends Steels have traditionally been used in the West, especially in heavy-use scenarios (e.g. butchering, where the edge deforms due to forceful contact with bone). These scenarios also lead Western trends toward blades tempered to a lower level of hardness (and thus lower brittleness). In East Asia, notably Japan, harder knives are preferred, so there is little need for steeling intra-day, as the edge does not deform as much. Instead, the blade is honed as needed on a waterstone. While tradition has kept the practice of steeling alive in Western kitchens, the majority of honing steels sold are abrasive rather than smooth, and knives are harder and more frequently made of stainless steel, which does not respond to traditional steeling techniques as well as high-carbon/low alloy tool steels.The sharpening steel is essential to maintain the sharpness of carving and other knives.Steel knife sharpener with bone handle. Part of a carving set.None.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, sharpening steel, carving set, kitchen equipment

Brought to Australia by Dutch migrants in the 1950s. Used for slow cooking of dishes such as soups and stews.Cream enamel with green upper rim. Three-legged. Consists of two circular compartments, the lower one of which is the kerosene tank. Adjustable wick in holder attached to a handle with which the wick can be raised and lowered. Spare wick in tank. Upper compartment has small brass porthole with glass centre through which to monitor flame. Inside bottom of upper compartment there is a longitudinal slit within an oval raised section. Perforations around slit for ventilation. Steel trivet on top has five pointed star pattern. household item

704 - Dyeline print of a drawing showing Ballarat Tramway (SEC) Fares, Charges, and Section Map. Also gives charges for Scholar's Monthly tickets, Luggage, Parcels, Newspapers and Chartered trams. Printed from Drawing No. VIX/131/1. Titled "Schedule of Fares and Charges - 26-1-1969". 2nd copy of 704 added 4/10/2015 from donation of Brendan Allan. 704.1 - as above, but with mileages added by the SEC - 26-2-1971 as part of the Transport Regulation Board review of tramway and bus services pending the replacement of the tramways later in 1971. Shows mileages between the various fare points in the nearest 1/4 mile. Two copies held - one rolled longitudinally, the other vertically.trams, tramways, ballarat, fares, sections, map

Three handwritten and three typed copies of notes on the Little 180 Mine. Notes include locality, underground connections, depth, plant, historical notes best gold, gold yield and dividends. References are in the left margin. Albert Richardson Collectiondocument, gold, little 180 mine, little 180 mine, notes on the little 180 mine, sheepshead line of reef, john brown factory, central red white & blue, central blue, ironbark south mine, rae's hill, a roberts & sons bendigo, s h johnson stratford, deborah consolidated mine, big 180 mine, new chum syncline mine, george lansell, new chum line of reef, a richardson, bendigo branch of royal historical society, mine's dept transverse and longitudinal sections little 180 mine, catalogue mining sales j h curnow, mine's dept special edition australian mining standard1/6/1899, mines dept booklet bendigo goldfield 1936, mine's dept quarterly and annual reports