A Gunter’s Chain, an old land surveying instrument, is named after its inventor, Edmund Gunter (1581-1626), an English mathematician and astronomer. It was first produced in 1620. The tool has 100 links and is 66 feet or one chain long. The links are marked off in groups of ten by metal tags or rings. A quarter chain (25 links) is called a rod or pole and ten chains make a furlong and 80 chains a mile. The traditional cricket pitch is 22 yards or one chain long. This chain is said to have been used by Gilbert Nicol when the Warrnambool to Hamilton Road was constructed in the 19th century. Gilbert Nicol was an early settler in Warrnambool who, with John Craig, established the first hotel (and the first building) in Warrnambool in 1847. Nicol later owned the property ‘Rosehill’ in the Warrnambool area. As the chain was given to the Warrnambool and District Historical Society by the Town Clerk, Keith Arnel, it is likely that the chain was one of the items in the old Warrnambool MuseumThis Gunter’s Chain is of importance because it is an early land measuring device that was used for over 250 years and has great historical and mathematical significance. If it is correct that it was used by Gilbert Nicol when the Warrnambool to Hamilton Road was built then it has considerable local significance and dates back to the 19th century. This is a metal tool which consists of 100 metal pieces or links joined together by loops at each end with two metal loops in between each link. The links joined together form a chain. The two ends of the chain have small metal handles attached. At intervals along the chain there are additional rings or metal pieces attached. The metal is very rusted.gunter’s chain, land measurement tools, history of warrnambool

This type of coal chisel was used in coal mining, blacksmithing, and heavy industrial work. It was designed to break apart coal or cut through other hard materials by striking the blunt end with a hammer. The BEARD & SISSON brand was known for manufacturing high-quality hand tools for industrial and mining applications. Such chisels were commonly used in the late 19th and early 20th centuries when coal mining was a major industry.This is a heavy-duty coal chisel, a short, thick metal tool with a flat, bevelled cutting edge at one end and a striking surface at the other. The chisel shows signs of rust and wear, indicating extensive use over time. The tool appears to be solid and robust, designed for heavy-duty applications such as splitting or cutting coal. Made BEARD & SISSON of Natimukcoal, chisel, blacksmith, mining, commercial item

Coopers tool for making wine barrelsSolid timber arch with a piece of timber slotted through with a metal attachment Wooden handle form which a metal cutting tool extends from

The harpoon was picked up on Warrnambool's Lady Bay beach in about 1950's. The harpoon is significant for its connection to the early history of Warrnambool and district, when whaling was a form of food gathering for indigenous people and for the very early settlers.Harpoon, whaling tool. Metal rod with harrow head and flared out handle.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, whaling harpoon, harpoon

Wooden mallets are usually used in carpentry or by a cooper to knock wooden pieces together, or to drive barrel bungs, dowels or chisels. A wooden mallet will not deform the striking end of a metal tool, as most metal hammers would. It is also used to reduce the force driving the cutting edge of a chisel, giving better control. Hardwood mallets are also used by a cooper to knock bungs or other wooden parts of a barrel in place.A significant tool a carpenter or cooper would use to knock wooden staves or furniture parts in place without damaging the soft surface of the timber being used. Item at this time cannot be associated with an historical event, person or place, provenance is unknown, item assessed as a collection asset as it is believed to have been produced before 1950.Mallet large with wooden handle attached to wooden head with 2 metal ferrules at top and bottom of head Nonewarrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, coopers tools, wooden mallet, barrel bung, carpenters tool, hammer

Wooden mallets are usually used in carpentry or by a cooper to knock wooden pieces together, or to drive barrel bungs, dowels or chisels. A wooden mallet will not deform the striking end of a metal tool, as most metal hammers would. It is also used to reduce the force driving the cutting edge of a chisel, giving better control. Hardwood mallets are also used by a cooper to knock bungs or other wooden parts of a barrel in place.A significant tool a carpenter or cooper would use to knock wooden staves or furniture parts in place without damaging the soft surface of the timber being used. Item at this time cannot be associated with an historical event, person or place, provenance is unknown, item assessed as a collection asset as it is believed to have been produced before 1950.Mallet wedge shaped with metal handleNonewarrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, coopers tools, wooden mallet, barrel bung, carpenters tool, hammer

J.E. Bleckmann were German Blade makers, registry shows Bleckmann (1899, No. 37190):J.E.Bleckmann, Solingen, registry class 9b). As well as blades for wood working tools they were also sword makers (used in American Civil War), Bayonet makers 1871-1918 and also pocket cutlery (pocket knives) as per advertisement 1907.This wood plane holds historical importance as carpentry tools such as this would have been used in the construction of local homes, outbuildings, furniture. It represents an era before power tools. Investigation is ongoing as to ownership and specific use in the area. Hand made wooden hand plane with metal blade. Carpentry tool from 19th century1/38 / 34 mm stamped into wood on front edge of plane. Metal Blade inscribed "J.E. BLECKMANN/ WARRANTED / CAST STEEL / SOLINGEN/GERMANY"tool, blade makers, hand plane, woodworking.

Tobacco smoking became a popular leisure activity in the 19th century. The corkscrew and the tapper accessories are used to clean the pipe and remove the debris after the tobacco is smoked in the pipe. The tamper is marked Capstan, which is a brand of pipe tobacco. The brand was first used in 1894 when W.D. & H.O. Wills launched their new product. The pipe tobacco accessories are associated with tobacco pipes and with Capstan tobacco, which became available in the 1890s. Smoking has been a popular leisure activity since the 19th century and continues now. The manufacturer of Capstan, W.D. & H.O. Wills, was the first company to mass-produce cigarettes.Pipe cleaners; a pair of metal accessories tools for cleaning tobacco pipes. One is a corkscrew, and the other is a tapper, shaped like a tapered nail. The tapper has an inscription. The brand is Capstan."Smoke" "Capstan"warrnambool, shipwreck coast, flagstaff hill, flagstaff hill maritime museum, flagstaff hill maritime village, capstan, tobacco pipe tools, tobacco accessories, pipe corkscrew, pipe tamper, tobacco tapper, tobacco smoking

Elastrator Kit containing a metal box, elastrator tool and marking rings. Used for the castration and docking of livestock.On Tool - Elastrator Reg. Trade Mark Aus. Pat. No. 122217 Des. App. No. 24946 On Glass Bottle - Part No

This Gunter’s Chain, an old land surveying instrument, is named after its inventor, Edmund Gunter (1581-1626), an English mathematician and astronomer. It was first produced in 1620. The tool has 100 links and is 66 feet or one chain long. The links are marked off in groups of ten by metal rings or tags. A quarter chain (25 links) is called a rod or pole and ten chains make a furlong and 80 chains make a mile. The traditional cricket pitch is 22 yards or one chain long. This Gunter’s Chain is of considerable significance because: 1. It is an early land measuring tool that was used for over 250 years and has great historical and mathematical significance. A Gunter’s Chain would have been used when forming and building local roads from the earliest days of settlement. 2. It has a possible local connection as it was given to the Historical Society by a local person in 1965 and possibly came from the property of ‘Rosehill’ This is a metal tool which consists of 100 metal pieces or links joined together by loops at each end with two metal loops in between each link. The links joined together form a chain. The two ends of the chain have small metal handles attached At intervals along the chain there are additional rings or metal pieces attached. Some white and green rope material has been used to bundle up the chain. The metal is somewhat rusted. gunter’s chain, land measurement tools, history of warrnambool

A tool such as this one would have been used by many householders in the past and those using guns in their occupations or hobbies – shooters, farmers, policemen etc. This item is retained as an example of a tool used in the past to re-load shot guns.This is a metal tool, with part of it painted green and containing a brass section. The top part of the tool has a round hollow section open at one end. The tool has a handle at one end (made of composite material) and a wing nut screw in the lower middle section. This enables the tool to be attached to a bench for stability. At the other end is a tapering piece of metal with a sharp end. This mechanism is attached with a screw and is able to be moved so that a section of it touches the open end of the hollow part on the top. vintage tools

This tool, with several others in a collection, is believed to have belonged to the Warrnambool carpenter and businessman, Henry Phillips. English-born Henry Phillips (1821-1896) came to Australia with his wife Elizabeth in 1849. They lived for some time in Port Fairy and in 1865 Henry formed a partnership with Christopher Beattie to establish the Warrnambool undertaking business of Beattie and Phillips. This business continued on after the deaths of the funders and lasted until the year 2000. In Warrnambool Henry Phillips was involved in the management of the Mechanics Institute.This item is of interest as an example of a vintage tool and as a memento of the Warrnambool carpenter and businessman, Henry Phillips.This is a metal vice tool with a circular ridged column and a turning handle at its end. The item is designed to be clamped onto a bench or table so that objects can be firmly clamped into the tool to be worked on in some way. vintage tools, henry phillips, warrnambool

This is one of a collection of items associated with Dr Felix Henry Meyer (1858-1937). Meyer was a very prominent early obstetrician and doctor, playing a part in the establishment of the role of the chair of obstetrics at the University of Melbourne in 1929. He was also a foundation member of the Royal Australian College of Surgeons.Metal surgical tool with bakelite handle. Tool consists of a metal shaft with a hook/clip at the end. Metal fixture on the side of the shaft, just above the handle, can be used to open and close the loop of the hook.surgery

All metal L shaped tool with bevelled ends 27mmL x 6mmH x 300mmW Marked Scott on underside.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Set of metal dissection tools in a plastic travelling case. Set consists of ten tools, including scalpels, scissors, tweezers and a puncture/needle tool. Manufacturer's stamp inside top of case reads 'RAMSAY/MELBOURNE'.RAMSAY/MELBOURNEsurgery

The spur is used in many equestrian disciplines.Most equestrian disciplines have rules covering spur design and use. Spurs are usually held on by a leather spur strap that goes over the arch of the foot and under the sole in front of the boot heel. The stirrup is a light frame or ring that holds the foot of a rider, attached to the saddle by a strap, often called a stirrup leather. Stirrups are usually paired and are used to aid in mounting and as a support while using a horse.E. Fisher grew up and lived at Mongan's Bride in the Kiewa Valley. Horse riding was common in the Kiewa Valley especially before the introduction of motorised vehicles.A spur is a metal tool designed to be worn in pairs on the heels of riding boots foe the purpose of directing a horse to move forward or laterally while riding. It is usually used to refine the riding aids and to back up the natural aids eg. the leg, seat, hands and voice. A stirrup is a light frame or ring that holds the foot of a rider, attached to the saddle by a strap, often called a stirrup leather. Stirrups are usually paired and are used to aid in mounting and as a support while using a horse. The spurs and stirrups are made of steel and the straps of leather.horse riding, spurs for horse riders, stirrups for horse riders, e.fisher

Item issued to Wayne William Forbes No 3176337 RAE. Refer Cat No 754 for service history also 2586. Part of an extensive collection including his fathers.7.62 SLR Rifle tool, metal with 3 sections that swivel from a central point. Used for adjusting rifle sites & gas settings.arms - accessories, military history, slr

Tool metal with wooden handle & pointed spike one end. Has broken ferrule holding spike. 115mmL x 125mmW Shipwrightflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Tools used by W.R. Cruickshank from 1920-1970's in Albury when he worked for Nicholson & Smith, Watchmakers and Jewellers.A multi-tool to cut and draw wire. Metal round nose tool with 5 sized wire holes. Handles are held with metal clamphorology, tools

This type of film developing tank was developed by Kodak in 1913. It was designed to allow the user to develop film in the daylight. The cylindrical tank inside the box with the dark apron surrounding it protected the film from the light. This model was 'Model 2' and Brownie size. The instruction booklet is dated to 1918.This objects helps to tell the story of photography as a hobby. It is an early example of a portable film developing which allowed the user to develop film in the daylight. It shows advancement in the technologies available to the hobby photographer.Rectangular timber box and lid. The lid has red lettering ' Kodak Film Tank'. The container part of the box has dovetail joints and a slight lip at the bottom where the base is larger than box. The box contains 2 metal turning handles, a cylindrical film tank and a metal tool which has a circular top end and a slight hook at the opposite end. The inside of the tank is painted black. The box also contains an instruction booklet. At the inside base of the box there is a paper leaflet pasted to the bottom. It has printed important and caution information on it as well as diagrams.Film / Kodak / Tankphotography, kodak, portland, glenelg shire, film, developing, film developing, hobbies, leisure, photographer

This item is from a collection donated by descendants of John Francis Turner of Wodonga. Mr. Turner was born on 6 June 1885. He completed all of his schooling at Scotts Boarding School in Albury, New South Wales. On leaving school, he was employed at Dalgety’s, Albury as an auctioneer. In 1924 John was promoted to Manager of the Wodonga Branch of Dalgety’s. On 15/03/1900 he married Beatrice Neal (born 7/12/1887 and died 7/2/1953) from Collingwood, Victoria. They had 4 daughters – Francis (Nancy), Heather, Jessie and Mary. In 1920, the family moved From Albury to Wodonga, purchasing their family home “Locherbie” at 169 High Street, Wodonga. "Locherbie" still stands in Wodonga in 2022. The collection contains items used by the Turner family during their life in Wodonga. These tool kits were often carried by men so they were equipped to deal with minor repair jobs away from home. A variety of companies in Britain and Germany manufactured similar kits prior to WW2.A metal miniature tool kit including a screwdriver, an awl and 2 augers stored in a metal cylinder. The cylinder screws together in the centre. There is a central slot on each side of the cylinder sot that the end of each tool can be inserted. The cylinder then screws together to act as a handle.pocket tool kits, hand tools

Fire iron stand; black, all metal stand with a singular spine attached to rectangular base. below the handle on the spine is a horizontal 'U' shaped rack with a hook at each end and a hook at the centre back of the 'U' for hanging tools. Decorative metal handles on tools and rack. 4 parts; stand, brush, shovel, poker. Impressed into underside of stand "B1O2" and " ATWN"flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, fire iron stand, fire iron, fire tools, fireplace set, fire iron set, domestic ware, heating

Prior to the 1900s, complicated births, particularly where there was a disproportion between the size of the woman’s pelvis and the foetus’ head, often meant the death of the baby and the mother. Instruments for removing a dead or ailing foetus from within the mother were used to attempt to save the mother’s life. The cranioclast, first invented by Dr. James Simpson in the mid-19th century and later redesigned by others, was used for fetal destruction and removal. Fundamentally a strong pair of forceps, the cranioclast was used to crush the skull, decreasing its diameter. In some cases, this would allow normal uterine contractions to expel the foetus; in others, the physicians would use an obstetrical hook to pull the body out of the mother. Doctors disagreed as to the pelvic diameter that would necessitate this drastic intervention, but generally found that 3 to 3.5 inches was the smallest size through which a living infant could pass. Equally of debate was the pelvic size through which the dead fetus could be extracted. When vaginal extraction was deemed unadvisable, Caesarian section would be performed. As caesarean section became safer and more common with the advent of anaesthetics and antiseptic techniques, the use of cranioclasts and obstetrical hooks diminished. (Museum of Health Care, Kingston) Dr Mitchell Henry O'Sullivan worked in the Victorian country town of Casterton as a general practitioner from 1919 until his death in 1977. He also practiced obstetrics. His son, Dr David More O'Sullivan donated his obstetric bag and its contents to the College in 1999. The bag and contents are a unique time capsule of the type of instruments and pharmaceuticals used in the inter-war period.Hinged metal tool with bakelite handles at one end and serrated teeth at other end. The instrument is in two sections. The right or upper blade has a black bakelite handle. There are two screws on the inside of the handle, 5.5cm apart. In the centre of the blade is a screw notch in the shape of a small horseshoe. On the inner side of the blade is a depression extending most of the length. The left, or lower, blade also has a black bakelite handle. There are two screws on the inside of the handle approximately 6cm apart. Mobile metal clasps in the shape of an 'S' , with three serrations, is attached to the distal end of the handle, which enables the blades to be opened or closed. destructive instruments

This is one of a collection of items associated with Dr Felix Henry Meyer (1858-1937). Meyer was a very prominent early obstetrician and doctor, playing a part in the establishment of the role of the chair of obstetrics at the University of Melbourne in 1929. He was also a foundation member of the Royal Australian College of Surgeons.Metal clamping tool, possibly associated with bone surgery. The instrument has a heavy-duty clamp style head at one end, and a bolt with a butterfly screw at the other end for locking the clamp in place. The handles of the tool are engraved with the text 'MAYER &/MELTZER' on one handle, and 'LONDON' on the other.'MEYER &/MELTZER' 'LONDON'surgery

Vietnam era SLR maintenance and cleaning kit in a green canvas holdall. It has a waxed coating, including the ties. The kit includes a pull through, a brush, a phial of oil and a metal adjustment tool. Each item is stored in its own individual pocket. (see also item 00092).

2 x metal/iron shaping tools. Flat rectangular metal piece has corrugated pattern underneath. This metal piece has a rectangular metal handle welded onto itblacksmith, forge, shaping tool

This hand groover is sometimes called a seamer, grooving iron, punch or fuller. It would have been used by a metal smith, such as a blacksmith, tinsmith or sheet metal worker. It is used to join two edges of metal. The smith overlaps the edges of the metal, then places the tool on top and beats it with a hammer on the top, forcing the metal into the tool's groove, which joins the metal. The device would be moved along the edges to complete the seam. The same tool could give a decorative finish to an artisan's work.This hand groover is sometimes called a seamer, grooving iron, punch or fuller. It would have been used by a metal smith, such as a blacksmith, tinsmith or sheet metal worker. It is used to join two edges of metal. The smith overlaps the edges of the metal, then places the tool on top and beats it with a hammer on the top, forcing the metal into the tool's groove, which joins the metal. The device would be moved along the edges to complete the seam. The same tool could give a decorative finish to an artisan's work.Tool: a fuller, used to form a groove in heated iron. It is also referred to as a groover, seamer or fuller punch. Hand tool with round handle, flat round top and indented rectangular base. Base has grooves on long edges. flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, blacksmith tool, vintage tool, sheet metal fabrication, groover, seamer, hand tool, tinsmth, metalsmith, seaming tool, sheet metal worker, manual tool, smith's tool, fuller, grooving iron, punch

This hand groover is sometimes called a seamer, grooving iron, punch or fuller. It would have been used by a metal smith, such as a blacksmith, tinsmith or sheet metal worker. It is used to join two edges of metal. The smith overlaps the edges of the metal, then places the tool on top and beats it with a hammer on the top, forcing the metal into the tool's groove, which joins the metal. The device would be moved along the edges to complete the seam. The same tool could give a decorative finish to an artisan's work.This handmade tool was made for the particular purpose of joining sheets of metal together. The metal formed in this way could be used for water tanks, boilers and other similar items. It is an example of the equipment made and used in the trades of a metalsmith and blacksmith in the 19th and early 20th centuries.Tool: a fuller, used to form a groove in heated iron. It is also referred to as a groover, seamer or fuller punch. Hand tool with round handle, flat round top and indented rectangular base. Base has grooves on long edges. flagstaff hill maritime museum, maritime museum, shipwreck coast, great ocean road, blacksmith tool, vintage tool, sheet metal fabrication, groover, seamer, hand tool, tinsmth, metalsmith, seaming tool, sheet metal worker, manual tool, smith's tool, fuller, grooving iron, punch