This model was found in the collection of Bay Steamers Maritime Museum. It is not knowt who created it but it is supposed that it was constructed to educate the many masters of the Wattle in the operation of a steam engine - a not so common mode of power these days. A Bay Steamers Maritime Museum examined the model in March 2012 and discovered that is was in poor repair. Using his existing knowledge, and with reference to some historic texts, he made some repairs and returned the model to working order. Here is his anaylsis of the situation as an excerpt from the Bay Steamers Maritime Museum newsletter Steamlines May 2012 "I was confronted with a model of a steam engine used years ago as a training aid for hopeful steam engineers. Already having a knowledge of steam operations, I considered a museum write-up for that model a ‘piece of cake’. However, on turning the model’s crankshaft, the valve timing seemed ‘out of kilter’ with the movement of the piston. Problem was that the two eccentrics on the crankshaft were not properly secured to it. Eventually I fastened the two eccentrics to the crankshaft where I felt that they should be and then realized that one of them had a chain-driven valve-timing device attached. This would be adjusted while an engine was running to achieve best performance and fuel economy whilst in operation by accurately controlling the period of time during which steam under pressure from the boiler would be admitted to the cylinder and give greater time for the steam to expand in the cylinder, move the piston and turn the crankshaft and thus, drive the attached apparatus. When the valves were correctly set up it was then possible to get the model to function properly.The model comprises a green section, which is the actual the model mounted on a brown painted board. There are two parts of the model, painted white representing the steam passages, and black representing the cast- iron portions of the cylinder-block casting, and of the main valve sliding between the cylinder a second sliding valve. Of the black portions, one slides back and forth being connected to a rod which is connected to an eccentric clamped to the crankshaft and is the nearer to the flywheel of two eccentrics. This eccentric is attached to the crankshaft at an angle of 90 degrees to the crank-pin attached to the flywheel. To operate the model simply turn the flywheel by means of the handle attached to its crank-pin. A second eccentric is also attached to the crankshaft, further away from the first eccentric, and it is adjusted to operate 90 degrees from the first eccentric (that is, 180 degrees from the crank-pin) A piston (painted silver) is located in a plastic cylinder and has a piston rod which passes through one end of the cylinder, (in actual practice a steam-proof gland seals the cylinder against loss of steam) terminating in a cross-head slide between four rails guiding it. From this cross-head, a connecting rod joins the piston-rod to the flywheel via the crank-pin attached to the flywheel which is part of the crankshaft. (In actual practice, a flywheel may not be used, particularly in a multi-cylinder engine.) The white portions of the model painted nearest to the cylinder represent the two steam ports cast into the main cylinder block, whilst one section painted in between those two represents the exhaust outlet (which may be connected to a condenser to conserve water, or to the open air). The main slide valve has three white-painted portions painted thereon. It has two white-painted marks representing the steam passages to the steam ports into the cylinder, and a third section in between the other two, being that part of the valve through which exhaust steam passes in line with the ports in the cylinder block. By rotating the flywheel, the operations of an engine will be observed as steam is admitted to the main valve via the gap between the two jaws of two moveable portions of a second sliding valve which is operated by the second eccentric attached to the crank-shaft. This eccentric is used to finely tune the valve timing of this model to obtain best running results of an engine. There are various methods used for reversing a steam engine. model compound steam engine, steam engine, model, crankshaft, valve, flywheel, wattle, engineer, eccentrics

hard red leather case with oxy valvesMA38 oxy-viva operating instructions

Brown, hard, cloth covered book of 121 pages plus advertisements. Chapters include steam pumps; pumps and injectors for feeding steam boilers; hand pumps; hydraulic rams; pumps for specific duties; pump valves; suction and delivery pumps; rules and notes relating to pumps. mining, pumps, pumping, powis bale, boilers, steam, hydrology, valves, windmills, waterworks, pipes

Drawing of the air brake system on a Melbourne tram using a self lapping brake and relay valve - the charging and release positions. 89.1 - shows the relay valve in the exhaust position 89.2 - shows the valve in the applied position. Has been drawn in ink on a piece of paper, and the coloured red or green as necessary to show the various positions and state of the valves, reservoir, brake cylinder and pipes.trams, tramways, mmtb, braking, brake valves

Pencil on paper student's technical drawings .1) Diaphragm valve assembly and main components .2) Diaphragm valve detail and parts .3) Centrifugal pump detailstechnical drawing, lyall e campbell, diaphgram valve, centifugal pump, school of mines ballarat

Clour Slide showing the outlet Valve at Lake Bellfieldgrampians, lake bellfield

This gas mask was the standard issue gas mask for the Australian Army prior to and going into the Second World War. The mask featured two eye pieces made out of splinter-less glass which were removable to allow for decontamination of the mask without damaging the splinter-less glass eye pieces. The filter box was manufactured by Willow in Melbourne. The mask features a tissot system, which uses air provided by the intake assembly to defog the eyepieces. Air breathed out passes directly through the outlet valve which was designed work as voice membrane in order to enhance the speech of the user Unknown to most is that the GSR series of masks were manufactured in Australia rather than being imported from the United Kingdom. This was mainly due to the long travel distance between the UK and Australia, as well as the fact that the UK could not afford to give out masks during the war. The majority of the masks were manufactured at the Commonwealth Ordnance Facility Maribyrnong in Melbourne.This mask is representative of Australian manufacture during WWII. It is part of the story of Australian military history.Gas mas with dark coloured rubber mask. The back of the mask has elastic harness with 6 straps. They can be tightened or loosened to fit. The front of the mask has two large glass eye pieces with metal rims and a metal outlet valve. A concertina fabric and rubber tube leads from the outlet valve to a reddish brown box which is the filter. One side of the mask has the word 'Normal' stamped into it.Mask: NORMAL (on left side) / DPR 12/40 (right side) Back of harness: No. 4 III / 5-11-49 Filter canister: No 4A / 1940 / E VIwar, wwii, world war two, second world war, adult gas mask, military, portland, glenelg shire, army

This item is likely a homemade or early commercial valve radio receiver, dating from the 1930s to early 1940s, during the golden age of radio. Many Australians built or assembled radios using kits or instructions from publications such as Wireless Weekly. Radios like this were central to home entertainment and news during the interwar and WWII years, especially in rural areas like Natimuk. The exposed construction suggests it may have been a hobbyist’s set or a demonstration model, used for educational purposes or by amateur radio enthusiasts.A partially assembled or open-frame valve (tube) radio chassis, mounted on a rectangular wooden baseboard. The unit features multiple cylindrical components including vacuum tubes, metal canister capacitors, and large tuning coils or condensers. Several wires extend from the board, some frayed or disconnected, indicating the item is no longer operational. The layout is typical of 1930s–1940s home-built or early commercial radios, often powered by batteries or mains with external speakers. Key visible components include: Four vacuum tubes (valves) with metallic tops Two large, rusted cylindrical capacitors or transformers Three tuning condensers (variable capacitors) with exposed fin assemblieswireless, radio, music, news, entertainment

Machined Bronze casting with sight glasses and feed control valvesDetroit Lubricator co.Detroit,u,s,a

Instruction card for Novita resuscitation apparatus model CInstructions for the use of "Novita"/Resuscitation Apparatus Model "C"/Open cylinder valve and control valve and apply the mask firmly to the/patient's face.Adjust the opening of the control valve so that the bag/is comfortably (but not over) inflated. The adjustment of the valve should/be such that the patient just fails to empty the bag on the inhalation./If the patient responds and begins to breathe freely air may be admitted/by uncovering the air inlet orifice on the metal tubular portion of the/face mask and the control valve may be partly or completely closed. If/the breathing becomes shallow again, open the control valve and close/the air inlet orifice./ SIEBE, GORMAN & CO. LTD./ CHESSINGTON, SURREYport melbourne authority (pma)

Red and black Viking Pro rubber diving suit with metal valve2/VIKING/PRO/VIKING/NORWEGIAN DIVING EQUIPMENTVIKING STAVANGERA.S NORWAY/VIKING/CF

Date and Location Unknown - Main Gas Valves in a Fenced off Paddockorganisation, industry, gas and fuel

tall air canister with a flat surface able to turn a valve for air

Steam Powered Water Pump in active use on George & George BoilerHistoric - Industrial Steam Powered Water Pump in active use on George & George Boiler Steam Powered Water Pump Blue with steel rods and brass valves.Snow steam Pump works Bufflalo, N.Y.,U.S.A Size 3x2x3 Number 51520puffing billy, water pump, steam, blue, snow steam pump works

Colour Slide showing the outlet valve prio to opening leaking watergrampians

Air regulator demand valve as used in scuba diving in 1960's ?

In line stop valve (possibly for steam) 14 cm flange. Brass

a. Triple-valve ratio arm. Sullivan Co. Serial No. 918/1941.

The banana bottle is often referred to as the hygienic bottle, and is aptly named. It was the saviour of many hand reared babies in early 20th C. It's ease of cleaning was a major breakthrough in nursery hygiene. The basic design was around for about 50 years. It first made its appearance around the mid 1880's. The first true banana feeder with a teat and valve was invented in 1894 by Allen and Hanbury's. In the next 15 years the model was modified over a series of four slightly different models. In 1910 the final design, The Allenbury Feeder was to remain unchanged for the next 50 years.A clear glass Felgrim Banana bottle (valve and teat) for feeding babies by hand. The brand is stamped in large ornate lettering inside an oval shape on the wide front of the bottle. It has two open ends for attaching teats. 8oz measurements are marked on one side and 16 tablespoons on the other. 'Felgrim' brand and 'Made in England Free from arsenic and lead'baby bottles, baby equipment, babies, domestic objects

When the Schomberg was launched in 1855, she was considered the "Noblest” ship that ever floated on the water. Schomberg's owners, the Black Ball Line had commissioned the ship for their fleet of passenger liners. She was built by Alexander Hall of Aberdeen for £43,103 and constructed with 3 skins. One planked fore and aft and two diagonally planked, fastened together with screw-threaded trunnels (wooden rails). Her First Class accommodation was simply luxurious with velvet pile carpets, large mirrors, rosewood, birds-eye maple and mahogany timbers throughout, soft furnishings of satin damask, and oak-lined library with a piano. Overall she had accommodation for 1000 passengers. At the launch, the Schomberg's 34-year-old master, Captain 'Bully' Forbes, had promised to reach Melbourne in sixty days stating, "with or without the help of God." Captain James Nicol Forbes was born in Aberdeen in 1821 and rose to fame with his record-breaking voyages on the famous Black Ball Line ships; Marco Polo and Lightning. In 1852 in the Marco Polo, he made the record passage from London to Melbourne in 68 days. Unfortunately, there were 53 deaths on the voyage, but the great news was off the record passage by Captain Forbes. In 1854 he took the clipper “Lighting” to Melbourne in 76 days and back in 63 days, this record was never beaten by a sailing ship. He often drove his crew and ship to breaking point to beat his previous records. He cared little for the comfort of the passengers. On this, the Schomberg's maiden voyage, he was determined to break existing records. Schomberg departed Liverpool on her maiden voyage on 6th October 1855 flying a sign that read "Sixty Days to Melbourne". She departed with 430 passengers and 3000 tons cargo including iron rails and equipment intended to build the Melbourne to Geelong Railway and a bridge over the Yarra from Melbourne to Hawthorn. She also carried a cow for fresh milk, pens for fowls and pigs, 90,000 gallons of water for washing and drinking. She also carried 17,000 letters and 31,800 newspapers. The ship and cargo were insured for $300,000 a fortune for the time. The winds were poor as she sailed across the equator, slowing Schomberg's journey considerably. The land was first sighted on Christmas Day, at Cape Bridgewater near Portland, Captain Forbes followed the coastline towards Melbourne. Forbes was said to be playing cards when called by the third mate Henry Keen, who reported land about 3 miles off. Due in large part to the captain's regarding a card game as more important than his ship, it eventually ran aground on a sand spit near Curdie's Inlet (about 56 km west of Cape Otway) on 26th December 1855, 78 days after leaving Liverpool. The sand spit and the currents were not marked on Forbes's map. Overnight, the crew launched a lifeboat to find a safe place to land the ship’s passengers. The scouting party returned to Schomberg and advised Forbes that it was best to wait until morning because the rough seas could easily overturn the small lifeboats. The ship’s Chief Officer spotted the SS Queen at dawn and signalled the steamer. The master of the Queen approached the stranded vessel and all of Schomberg’s passengers and crew disembarked safely. The Black Ball Line's Melbourne agent sent a steamer to retrieve the passengers' baggage from the Schomberg. Other steamers helped unload her cargo until the weather changed and prevented the salvage teams from accessing the ship. Later one plunderer found a case of Wellington boots, but alas, all were for the left foot. Local merchants Manifold & Bostock bought the wreck and cargo but did not attempt to salvage the cargo still on board the ship. They eventually sold it on to a Melbourne businessman and two seafarers. In 1864 after two of the men drowned when they tried to reach Schomberg, salvage efforts were abandoned. In 1870, nearly 15 years after the wreck parts of the Schomberg had washed ashore on the south island of New Zealand. The wreck now lies in 825 metres of water and although the woodwork is mostly disintegrated the shape of the ship can still be determined due to the remaining railway irons, girders and the ship’s frame. A variety of goods and materials can be seen scattered about nearby. There have been many other artefacts salvaged from the wreck include ship fittings and equipment, personal effects, a lithograph, tickets and photographs from the Schomberg. This item was retrieved from the shipwreck site during early salvage efforts on the vessel. And was donated to the Flagstaff Hill collection of Schomberg shipwreck artefacts.This artifact is particularly significant in that along with other items salvaged from the wreck have helped in part to having legislation changed to protect shipwrecks, with far tighter controls being employed to oversee the salvaging of wreck sites. This item forms part of the Schomberg collection at Flagstaff Hill maritime museum. The collection as a whole is of historical and archaeological significance at a State level. Flagstaff Hill’s collection of artefacts from the Schomberg is also significant for its association with the Victorian Heritage Registered Schomberg shipwreck (VHR S 612). The collection is of additional significance because of the relationship between the objects salvaged, as together they help us to interpret the story of the Schomberg. The collection as a whole is historically significant for representing aspects of Victoria's maritime history and its potential to interpret social and historical themes from society at the time of the wreck. Brass keg spigot valve/tap, Schomberg Artifact Reg No S/94.Nonewarrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, schomberg, shipwrecked-artefact, clipper ship, black ball line, 1855 shipwreck, aberdeen clipper ship, captain forbes, peterborough shipwreck, ss queen, keg tap, brass keg tap

Date and Location Unknown - Rupert Hamer (Premier of Victoria) Opening a Gas Valve.Kodakperson, individual, rupert hamer

Turnable valve Red and Green glass gems, Red is trigger then the Green A HandlePanther PcH B'HAM

Yields information about a compressor governor that is fitted to some Ballarat Trams, Westinghouse.Two A4 photocopied sheets, giving a side elevation of the Westinghouse "S-6-A Electric Compressor Governor" and the setting or the regulation and adjustment, installation and maintenance of the Governor. Commonly known as a "Bettleback" Governor. Dates from 1916. See Reg Item 703 for a MMTB drawing. WAD’s thoughts on setting Beetle back compressor Governors – 19/12/2009. Refer to instructions as well. Set both valves to approximately the same tension or thread length If when pumping up, both valves start to chatter, screw down the back valve further. When working satisfactorily, but pressures not right, that is, the governor is cutting out without valves chattering or with excessive range or pressure too high. Adjust the front valve until the desired cut out pressure arrived at. The cap must be on this valve for it to work. Adjust the back valve to adjust the cutting in setting, screw down for high cut in pressure. Adjust both as necessary to obtain your desires! And best of luck, it can be done, but is frustrating!!!!!trams, tramways, governors, westinghouse, air compressors, instructions

The Lidwill machine was designed by Mark Lidwill in 1913, for the purpose of mechanical or insufflation anaesthesia. It was manufactured by Elliott Bros. of Sydney.Colour photograph of a Lidwill anaesthetic machine sitting on carpet. A circular metal ether vaporiser sits on a brown wooden base, with brown tubes connecting to a trap bottle and metal valves, and a brown tube connected to the valve is coiled on the floor.anaesthetic equipment, lidwill anaesthetic machine, mark lidwill, ether vaporiser, elliott bros sydney