Showing 219 items matching wood cutting
-
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Tools, Coping saw, c1900
A coping saw is a type of hand saw used to cut intricate external shapes and interior cutouts in woodworking or carpentry. It is widely used to cut mouldings to create coped rather than miter joints. It is occasionally used to create fretwork though it is not able to match a fretsaw in intricacy of cut, particularly in thin materials. Coping saw blades are always thicker and much coarser cutting than typical fretsaw blades. A coping saw consists of a thin, hardened steel blade, stretched between the ends of a square, c-shaped, springy-iron frame to which a handle is attached. The blade is easily removed from the frame so that the blade can be passed through a drilled hole in the middle of a piece of wood. The frame is then re-attached to the blade and the cut starts from the middle of the piece. Long cuts perpendicular to the edge of the material are possible but the shallow depth of the frame rather limits how far from the edge one may cut. The much deeper frame of the fretsaw is more useful for cutting well away from the edge but conversely cannot manage the thicker materials commonly cut by the coping saws. The coping saw blade is installed with the teeth pointing towards the handle. Unlike a hacksaw, which has the teeth pointed away from the handle, the coping saw cuts on the pull stroke. The coping saw blade is removable by partially unscrewing the handle. The blade is prevented from rotating by means of the short, steady bar provided where the blade is attached. Loosening the handle also allows the blade to be rotated relative to the frame as desired. Carefully aligning the finger steady bars at the top and bottom of the blade ensures that the thin blade is straight and not twisted along its length. Re-tightening the handle tensions the blade and locks it at the desired angle relative to the frame. The short steady bar nearest the handle is held securely between finger and thumb while the handle is tightened to ensure the blade remains at the desired angle. Unlike the fretsaw the coping saw blade has holding pins which lock securely into the angled slots of the rotatable blade holders. Gentle curves are achieved by slowly turning the whole frame by means of the handle while continuing to cut steadily. A coping saw with wooden handle but no bladetools, saws, steel , clamps, metalwork, woodwork, carpentry, early settlers, pioneers, market gardeners, moorabbin, bentleigh, cheltenham, fretsaw, coping saw, bowsaw, blacksmiths, -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Tools, Screwdriver large, c1900
A screwdriver is a tool, manual or powered, for turning (driving or removing) screws. A typical simple screwdriver has a handle and a shaft, and a tip that the user inserts into the screw head to turn it. The shaft is usually made of tough steel to resist bending or twisting. The tip may be hardened to resist wear, treated with a dark tip coating for improved visual contrast between tip and screw—or ridged or treated for additional 'grip'. Handle are typically wood, metal, or plastic and usually hexagonal, square, or oval in cross-section to improve grip and prevent the tool from rolling when set down. The handle and shaft of screwdrivers have changed considerably over time. The "Perfect Pattern Handle’ screwdriver was first manufactured by HD Smith & Company, which operated from 1850 to 1900. Screwdrivers were probably invented in the late 15th century, either in Germany or France when Screws were used to construct screw-cutting lathes, for securing breastplates, backplates, and helmets on medieval jousting armor—and eventually for multiple parts of the emerging firearms, particularly the matchlock. The jaws that hold the pyrites inside medieval guns were secured with screws, and the need to constantly replace the pyrites resulted in considerable refinement of the screwdriver. The screwdriver depended entirely on the screw, and it took several advances to make the screw easy enough to produce to become popular and widespread Canadian P.L. Robertson, though he was not the first person to patent the idea of socket-head screws, was the first to successfully commercialize them, starting in 1908. In Portland, Oregon, Henry F. Phillips patented his own invention, an improved version of a deep socket with a cruciform slot, today known as the Phillips Screw. Phillips offered his screw to the American Screw Company, and after a successful trial on the 1936 Cadillac, it quickly swept through the American auto industry. A main attraction for the screw was that conventional slotted screwdrivers could also be used on them, which was not possible with the Robertson Screw. A large steel screwdriver with worn wooden handlepioneers, early settlers, market gardeners, moorabbin, bentleigh, cheltenham, brighton, tools, craftsman, carpenters, , blacksmiths, builders, farmers, metalwork, woodwork, screws, philllips head screwdrivers, h.d.smith & co usa, p.l. robertson, henry f.phillips , oregon, canada, american screw company, -
Federation University Historical Collection
Annual Reports, Report of the Horticultural Society of Victoria, 1884-1890, 1884 - 1990
Members of the Report of the Horticultural Society of Victoria had the privilege of procuring seeds, cuttings, scions, &c., from the Society's gardens; also, free admission with 2 ladies, to all the Exhibitions of the Society. The 3 booklets were deaccessioned from the Victorian School of Foresty Library on 02 November 1981Three small booklets containing the annual report of the Report of the Horticultural Society of Victoria. .1) 23 page booklet for 1884 including annual report, reports of exhibitions, list of life members and list of member for 1884. Members included William Lee of Daylesford, R. McVicars of Koroit, and W.J. Wood of Daylesford .2) 36 page booklet for 1886 including annual report, financial statement, Fruit exportation, reports of exhibitions, list of life members and list of member for 1884. Members included William Lee of Daylesford, W. Anderson of Koroit, and W.J. Wood of Daylesford .3) 41 page booklet for 1890 including annual report, amended constitution, financial statement, Fruit exportation, reports of exhibitions, list of life members and list of member for 1884. Members included J. Dunstan of Yuille's Flat, Ballarat; and W.J. Wood of Daylesford. h.r. loch, w.f. stawell, boyce, carson, loch, stawell, beilby, stoddart, w.j. stoddart, william bailey, bailey, coglan, h. coglan, sangster, w. sangster, george neilson, victorian school of foresty, natale d'angri, d'angri, lang, rennie & co., r.u. nicholls, ramus, john ross, lindt, j.w. lindt -
Federation University Historical Collection
Books, H.E. Daw Government Printer, Ballarat School of Mines and Industries Departmental Papers, 1914-1950
Used at the Ballarat School of Mines and the Ballarat Technical Art SchoolThis collection of examinations is significant because of its completeness with the full range of examinations between 1914 and 1950.Large leather bound books, with leather spine, containing all examinations held at the Ballarat School of Mines (including the Ballarat Technical Art School and Ballarat Junior Technical School). The examination papers were supplied and printed by the Education Department, Victoria. Examinations include: Agriculture, Algebra, Architecture, Arithmetic, Applied Mechanics, Assaying, Biology, Botany, Boilermaking, Building Design, Blacksmithing, Bricklaying, Carpentry and Joinery, Coachbuilding, Cabinet Making, Civil Engineering, Cabinet Making, Commercial, Chemistry, Engineering Drawing, Economics, English, Electrical technology, Electricity and Magnetism, Electric Wiring, Electric Welding, Electrical Fitting, Electrical Trades, Food Analysis, Geology, Geological Mapping, Graphics, Geometry, Heat Engines, Heat Treatment, Hydraulics, Hand Railing, Instrument Making, Millinery, Milling and Gearouting, Machine Shop Practice. Metal Founding, Mining, Metallurgy, Mineralogy, Mathematics, Motor Mechanics, Mine Surveying, Mining Mechanics, Petrology, Physics, Painting and Decorating, Pattern Making, Plastering, Plumbing and Gasfitting, Printing, Refrigeration, Spelling, Science , Shorthand, Surveying. Signwriting. Sheet Metalwork, Toolmaking, Ladies Tailoring, Trigonometry, Typewriting, Welding, Commercial Geography. Millinery, Dressmaking, Needlework, Decorative Needlework, Architecture, Building Design and Construction, Art (Composition in Form and Colour), Art (Casting Clay MOdels) Art (Drapery), Art (Drawing the Human Figure From Casts), Art (Drawing the Antique from Memory), Art (Drawing from Memory); Art (Drawing Plant Forms from Nature, Art (Drawing Plant Forms From Memory), Art (Drawing from Models and Objects), (Drawing From a Flat Example). Art (Drawing in Light and Shade from a Cast of Ornament or Lower Nature), Art (Drawing Ornament from the Cast), Art (Drawing from Models or Objects), Art (Drawing fro Dressmakers' and Milliners' Fashions), Art (Drawing With the Brush), Art (Drawing from a Flat Example); Art (Modelled Design), Art (General Design), Art (Embossed Leatherwork), Art (Practical Plane Geometry), Art (Practical Solid Geometry), Art (Geometrical Drawing), Carpentry and Joinery, Art (Human Anatomy), Art (Historic Ornament), Art (House Decoration), Art (LEttering), Signwriting, Art (Light Metalwork), Art (Modelling), Art (Modelling the Human Figure from a Life), Art (Stencilling); Art (Wood Carving) Refrigeration, Teaching, Boilermaking, Blacksmithing, Carpentry and Joinery, Coachbuilding and Carriage Drafting, Electric Wiring, Electrical Fitting, Graining and Marbling, Instrument Making , Machine Shop Practice, Metal Founding, Milling and Gear Cutting, Motor Mechanics, Painting and Decorating, Sheet Metalwork, Toolmaking, Printing, Pattern Making, Plumbing and gasfitting, examinations, ballarat school of mines, ballarat technical art school, trades, education department victoria, agriculture, algebra, architecture, arithmetic, applied mechanics, assaying, biology, botany, boilermaking, building design, blacksmithing, bricklaying, carpentry and joinery, coachbuilding, cabinet making, civil engineering, commercial, chemistry, engineering drawing, economics, english, electrical technology, electricity and magnetism, electric wiring, electric welding, electrical fitting, electrical trades, food analysis, geology, geological mapping, graphics, geometry, heat engines, heat treatment, hydraulics, hand railing, instrument making, millinery, milling and gearouting, machine shop practice, metal founding, mining, metallurgy, mineralogy, mathematics, motor mechanics, mine surveying, mining mechanics, petrology, physics, painting and decorating, pattern making, plastering, plumbing and gasfitting, printing, refrigeration, spelling, science, shorthand, surveying, signwriting, sheet metalwork, toolmaking, ladies tailoring, trigonometry, typewriting, welding., dressmaking, needlework, decorative needlework, architecture, building design and construction, art (composition in form and colour), art (casting clay models), art (drapery), art (drawing the human figure from casts), art (drawing the antique from memory), art (drawing from memory), art (drawing plant forms from nature, art (drawing plant forms from memory), art (drawing from models and objects), (drawing from a flat example), art (drawing in light and shade from a cast of ornament or lower nature), art (drawing ornament from the cast), art (drawing from models or objects), art (drawing for dressmakers' and milliners' fashions), art (drawing with the brush), art (drawing from a flat example), art (modelled design), art (general design), art (embossed leatherwork), art (practical plane geometry), art (practical solid geometry), art (geometrical drawing), art (human anatomy), art (historic ornament), art (house decoration), art (lettering), art (light metalwork), art (modelling), art (modelling the human figure from a life, art (stencilling), art (wood carving), teaching, coachbuilding and carriage drafting, graining and marbling, milling and gear cutting, commercial geography, exams, examination book -
Federation University Historical Collection
Document, Ballarat Technical Art School Staff Timetable and Salaries, c1906
Ballarat East Technical and Art School is an early division of the School of Mines Ballarat Handwritten sheet showing teachers' names, subjects, days, hours etc.Ballarat East Technical and Art School stamp at the bottom of the page.ballarat east technical and art school, f. foster, g. wightman, j.c. barber, a.w. steane, a. hughes, jno l. eddy, freehand, geometry, brush drawing, engineering drawing, sign writing, model drawing, wood carving and repousse, dress cutting, ballarat east art school, albert w. steane -
Flagstaff Hill Maritime Museum and Village
Domestic object - Wooden Rolling Pin, First half of 20th Century
A rolling pin is a simple tool used to flatten dough. The first civilisation known to have used the rolling pin was the Etruscans. Their advanced farming ability, along with a tendency to cultivate many plants and animals never before used as food and turn them into sophisticated recipes, were passed to invading Greeks, Romans, and Western Europeans. Thanks to the Etruscans, these cultures are associated with gourmet cooking. To prepare their inventive foods, the Etruscans also developed a wide range of cooking tools, including the rolling pin. Although written recipes did not exist until the fourth century B.C., the Etruscans documented their love of food and its preparation in murals, on vases, and on the walls of their tombs. Cooking wares are displayed with pride; rolling pins appear to have been used first to thin-roll pasta that was shaped with cutting wheels. They also used rolling pins to make bread (which they called puls) from the large number of grains they grew. Natives of the Americas used more primitive bread-making tools that are favoured and unchanged in many villages. Chefs who try to use genuine methods to preserve recipes are also interested in both materials and tools. Hands are used as "rolling pins" for flattening dough against a surface, but also for tossing soft dough between the cook's two hands until it enlarges and thins by handling and gravity. Tortillas are probably the most familiar bread made this way. Over the centuries, rolling pins have been made of many different materials, including long cylinders of baked clay, smooth branches with the bark removed, and glass bottles. As the development of breads and pastries spread from Southern to Western and Northern Europe, wood from local forests was cut and finished for use as rolling pins. The French perfected the solid hardwood pin with tapered ends to roll pastry that is thick in the middle; its weight makes rolling easier. The French also use marble rolling pins for buttery dough worked on a marble slab. Glass is still popular; in Italy, full wine bottles that have been chilled make ideal rolling pins because they are heavy and cool the dough. Countries known for their ceramics make porcelain rolling pins with beautiful decorations painted on the rolling surface; their hollow centres can be filled with cold water (the same principle as the wine bottle), and cork or plastic stoppers cap the ends. Designs for most rolling pins follow long-established practices, although some unusual styles and materials are made and used. Within the family of wooden rolling pins, long and short versions are made as well as those that are solid cylinders (one-piece rolling pins) instead of the familiar style with handles. Very short pins called mini rolling pins make use of short lengths of wood and are useful for one-handed rolling and popular with children and collectors. Mini pins ranging from 5 to 7 in (12.7-17.8 cm) in length are called texturing tools and are produced to create steam holes and decorations in pastry and pie crusts; crafters also use them to imprint clay for art projects. These mini pins are made of hardwoods (usually maple) or plastic. Wood handles are supplied for both wood and plastic tools, however. Blown glass rolling pins are made with straight walls and are solid or hollow. Ceramic rolling pins are also produced in hollow form, and glass and ceramic models can be filled with water and plugged with stoppers. Tapered glass rolling pins with stoppers were made for many centuries when salt imports and exports were prohibited or heavily taxed. The rolling pin containers disguised the true contents. The straight-sided cylinder is a more recent development, although tapered glass pins are still common craft projects made by cutting two wine bottles in half and sealing the two ends together so that the necks serve as handles at each end.Tiny rolling pins are also twisted into shape using formed wire. The pins will not flatten and smooth pastry, and the handles do not turn. The metal pins are popular as kitchen decorations and also to hang pots, pans, and potholders. https://www.encyclopedia.com/sports-and-everyday-life/food-and-drink/food-and-cooking/rolling-pinThe use of the rolling pin to make thin pastry or pasta.Wooden rolling pin with some damage on cylinder section.None.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, rolling pin, cooking, pastry -
Flagstaff Hill Maritime Museum and Village
Tool - Spokeshave, Prior to 1950
A spokeshave was made with a wooden body and metal cutting blade. With industrialization metal bodies displaced wood in mass-produced tools. Spokeshaves can be made from flat-bottom, concave, or convex soles, depending on the type of job to be performed. They can include one or more sharpened notches along which the wooden shaft is pulled in order to shave it down to the proper diameter. Historically, spokeshave blades were made of metal, and the body and handles were wood. Unlike a draw knife, but like a plane, spokeshaves typically have a sole plate that fixes the angle of the blade relative to the surface being worked. By the twentieth-century metal handles and detachable blades had become the most common. A convex, wooden, variant of the spokeshave is called a travisher, at one time mostly used in chair making.A tool of the cooper and other woodworking tradesmen that has been in use since the making of barrels and wooden buckets for hundreds of years without much change to the design or how the tool is used. Curved Spokeshave with metal handlesNonewarrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, coopers tools, hand plane, joiners tools, wagoner's tools, spokeshave -
Flagstaff Hill Maritime Museum and Village
Tool - Joiner or Jack Plane, Late 19th to first quarter of the 20th century
A jack plane (or fore plane) is a general-purpose woodworking bench plane, used for dressing timber down to the correct size in preparation for truing and/or edge jointing. It is usually the first plane used on rough stock, but in exceptional cases can be preceded by the scrub plane. Jack planes are 300–460 mm long and 64–76 mm wide, with wooden-stocked planes sometimes being slightly wider. The blade is 44–57 mm wide that is often slightly convex (or ground with rounded corners) to prevent digging in to or marking the work. The cut is generally set deeper than on most other planes as the plane's purpose is to remove stock rather than to gain a good finish (smoothing planes are used for that). In preparing stock, the jack plane is used after the scrub plane and before the jointer plane and smoothing plane. The carpenters' name for the plane is related to the saying "jack of all trades" as jack planes can be made to perform some of the work of both smoothing and jointer planes, especially on smaller pieces of work. Its other name of the fore plane is more generally used by joiners and may come from the fact that it "is used before you come to work either with the Smooth Plane or with the Jointer". Early planes were all wood, except for the cutter, or combined a wood base with a metal blade holder and adjustment system on top. Although there were earlier all-metal planes, Leonard Bailey patented many all-metal planes and improvements in the late 19th century. A jack plane came to be referred to as a "No. 5" plane or a "Bailey pattern No. 5" at the end of the 19th century. A vintage tool made by an unknown company, this item was made commercially for firms and individuals that worked in wood and needed a tool that could remove large amounts of timber. These jack or dressing planes came in various shapes and sizes to achieve a flat and even finish to timber surfaces before the use of smoothing planes and came in many sizes. A significant tool from the mid to late 19th century that is still in use today with early models sought after by collectors. It gives us a snapshot of how furniture and other finishes were created on timber by the use of cutting edged hand tools. Tools that were themselves handmade shows the craftsmanship used during this time not only to make a tool such as the subject item but also the craftsmanship needed to produce a decorative or even finish that was needed for the finishing of timber items. Jack or Fore plane with blade and wedge. Marked "D Morris" (owner)flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, plane, fore plane, d morris, jack plane, wood working tools -
Flagstaff Hill Maritime Museum and Village
Tool - Wood Moulding Plane, 1770-1809
The story of Christopher Gabriel born on April 2, 1746, in Falmouth England is a tale of a poor boy who made good. Shortly before he turned thirteen years of age in 1759 he was apprenticed to a local master carpenter, recorded as a Mr Barnicot the master trained his apprentice well as we can assume by Christopher's later successes. The apprenticeship ended in 1766 after seven years when Christopher reached twenty. Then in 1768, he relocated to London walking the two hundred miles from Falmouth carrying his possessions in a sack. He no sooner arrived in London when he met Alice Trowell who became his wife in March 1769. They set up house on Albermarie Street Clerkenwell and by the first of 1770, Gabriel had begun his business of plane making. It has been speculated that Gabriel took over the shop of John Cogdell aided with an investment from his in-laws of 131 pounds. He went on to prosper as a plane-maker and lumber merchant over the next forty years. His business did well and in 1774 Gabriel moved to a house in Golden Lane, London and 1779 moved again to a home in Ould Street London. By now Gabriel was making a name for himself and his business at this time was located at 32 Banner Street Golden Lane, the following year he purchased another home in Banner Street and 1793 purchased the house next door. At the time of his death in 1808, he owned twenty-seven houses and commercial building. Christopher Gabriel s descendants became quite prominent in England and his grandson, Sir Thomas Gabriel became the Sheriff of London and Middlesex in 1859 and the Lord Mayor of London 1866 and 1867. Gabriel was an extremely prolific plane-maker with a lot of examples made in the 18th century can still be found today. He made good quality tools and was an innovator of several new plane designs. A vintage tool made by a well-known plane-maker, this item was made commercially for firms and individuals that worked in wood and needed a tool that could give a decorative finish to timber. These planes came in various shapes and sizes to achieve a finish to timber surfaces and came in many sizes. A significant Christopher Gabriel plane from the mid to late 18th century that after 200 years can still be used today. Planes made by Gabriel are eagerly sought after by collectors. The tool gives us a snapshot of how furniture and other finishes were created on timber by the use of cutting edged hand tools. Tools that were themselves hand made shows the craftsmanship used during this time not only to make a tool such as the subject item but also the craftsmanship needed to produce a decorative or even finish that was needed for the finishing of timber items. Moulding multi patterned plane has a "5" long bladeStamped Maker C Gabriel (owner JB).flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, side rabbet plane, gabriel m hobling -
Kiewa Valley Historical Society
Saw Logging, circa early 1900's
... the Kiewa Valley. It has been used for domestic wood cutting ...This item can be seen as a hand piece belonging to a logger or farmer spanning over one hundred or more years. The equipment was made to perfection as a hand tool and has not been improved upon since its introduction into the logging industry or farming fraternity. It can be used by one person or two (husband and wife or father and child). Its versatility is ageless. It can be used for domestic clearing of the paddocks, or for domestic fire places and stoves or commercial logging up until the 2000s (introduction of specific logging trucks that cut and treat the trees in one process).This item is very significant to the rural and logging regions within the Kiewa Valley. It has been used for domestic wood cutting and for industrial logging in the mid to late 1900s. It was used when clearing land for the SEC Hydro scheme and to allow for the introduction of the Mount Beauty construction workers' village (later developed into the town) The great advantage of this saw was that it uses only muscle power and can be located where ever a lumber "Jack" or property owner can venture. either by foot or by horse.This saw is a Warranted Superior One/Two Man Logging Saw. It has 68 teeth and is 42 inches long. At a position of one inch (2.5cm) from the end is a hole one inch down from the leading edge. There is another hole 45 cm in front of the handle. Both these holes are for a "helper handle" which when in use renders this logging saw fit for a two man operation. This is a cross cut saw for cutting down vertical trees (horizontal cut) The handle is made from wood and fastened to the blade by three heavy duty screws. The one helper handle stands 150mm high and has a 150mm wooden hand grip.The central screw has 25mm manufacturers' identification logo stamped "WARRANTED SUPERIOR".one or two man cross cut saws, forestry, timber industry -
Kiewa Valley Historical Society
Drill Auger, Circa early 1900s
This item wasused before diesel, electric and battery drilling apparatus were used by farmers, and other trades requiring a portable yet reliable method of drilling holes. As this item is a 3/4 inch hole drill it would be suitable for fencing and providing holes for structural studs. As with all outdoor farm equipment, man power was required (be it the farmer or farm hands). Fitness of the operator was at a high standard but protective gloves were not highly thought of as it was before occupational, health and safety regulations became mandatory over all manual handling activities, be they on rural properties or town/city factories. This period was one where the male ego was at its pinnacle i.e. the harder the tasks the more of a man was required. Hard manual work was not only the "way to go" but also a necessity. Evolution of cheap portable electric/battery powered tools opened up a more efficient method available, especially to those with less muscle strength. This item personifies the rugged environment of the rural workplace. The Kiewa Valley with its main emphasis on farming and grazing provided ample opportunity to use this construction implement. The manufacturer being a Scottish tool company is very significant in the era when this hole maker was in high demand. British steel products were of high grade and had a good record of reliability. The reliability of any tool was a solid factor for farmers and tradesmen in this semi-isolated region (Circa early 1900s) within the Kiewa Valley and its regional area. This factor,although not as crucial, post 1960s, when Asian manufacturers entered the market place and produced cheaper tools and transportation and supplies was more frequent and reliable, the need for the more expensive British made tools diminished considerably. After the influx of tradesmen from war torn Europe (post 1945) and the increased availability of tradesmen in the Kiewa Valley and its region the price of tools was and still is not as crucial and the cost of all required tools has become a minimal part of the equation. It is only with the emerging younger trades person, farmer and grazier, who have more, "one eye on production costs" and no "old ties to the motherland" inert mind set that quality tools such as this auger and other hand tools "must be made to last a life time" is no longer part of the modern work environment.This cast iron, hand operated Auger has a short barrel shaped cylinder at one end (known as the "Eye") and at the other end a Helical screw blade (screws the cutting edge into wooden material, thereby creating a hole 3/4 inch diameter in the wood) . The barrel section at the top permits a metal or wooden leverage plank to be inserted. The main rod has a 180mm long cutting/screw blade running from the bottom up towards the "eye" end. From the end of the screw blade to the handle is 380mm and cylindrical, but this changes at 550mm from the "eye" end to a 14mm x 10mm rectangular shape shaft.This shaft end is welded to the "Eye".On the shaft below the "eye" is stamped " MATHESON GLASGOW" on the front side and a spade (cards) symbol on the back.auger, hand drill, fencing, tool, rural trades, brace & bit -
Kiewa Valley Historical Society
Tobacco Tying Horse and Stick
Tobacco farming began circa 1960 in the Kiewa Valley and consequently became one of its major industries. Many of the Italian families were involved in tobacco farming.Historical: This equipment was used on one of the tobacco farms in the Kiewa Valley. The Tying Horse was home-made showing the resourcefulness of farmers living in the Kiewa Valley. Provenance: The tobacco farmer came from Italy and was sponsored to visit a tobacco farmer in Myrtleford to learn how to grow tobacco so that he could transfer those skills to his own farm in the Kiewa Valley.Burley tobacco stick is different to Hicks type stick. Tying of green leaf on the sticks - with the twine attached. There is small sharp metal blade on the end of the horse used for cutting twine. Rectangular wooden frame. The beam along the bottom is kept in place by 2 diagonal planks on each side and at both ends. The beam keeps the frame upright with 2 cross beams at each end. At each end there is a vertical beam with a 'V' cut out of each to hold a wooden beam/stick/tree branch. Wood is rough.tobacco. kiewa valley.tying horse. guido angelini. -
Kiewa Valley Historical Society
Collection - Mt Beauty Drama Group
Mt Beauty Drama groupMt Beauty formed a drama group to entertain the community as they lived in a small remote town. Collection consists of: 1. Six typed A4 sheets - 'Out in the Cold Cold Snow' 2. Blue booklet A5 94 pages 'Sailor, Beware' and 3 copies of the handout to the audience including the cast 3. Orange booklet A5 8 pages 'Red Hot Cinders' and a copy without the orange cover. 4. Foolscap size with yellow pages at the front followed by 42 white pages 'Babes in the Wood' 5. A white card listing the cast for 'The Importance of Being Earnest' 6. Colored pages of handout for 'Cinderella' including the cast and dated 1959 7. 3 newspaper cuttings 8. 4 photos - Sailor Beware Photos are labelledmt beauty, drama group, entertainment, organisation, the arts -
Ringwood and District Historical Society
Newspaper - Newspaper Cutting, The Box Hill Reporter clipping, 1922 - Ringwood articles, 7-Feb-22
Newspaper fragment "The Reporter" No.7 Vol XXXIII Feb 7, 1922 - including Russell, Bona & Russell, Solicitors, Melbourne Street, Ringwood; Ringwood House Accommodation - Mrs Tudor, Proprietress; Ringwood Livery Stables and Warrandyte Coach Line - Wm. Hussey, Proprietor; Menace of Fires - worst outbreak in Mr. Kent's property on the Warrandyte Road; After Fifty Years - golden wedding of Mr and Mrs. Milne, late of Ringwood; Prizes at Ringwood Show; Wood Chop Contests at Ringwood Show. -
Warrnambool and District Historical Society Inc.
Document: Cuttings, Warrnambool Steam Packet Company, C 1890
THis collection of cuttings relates to the Warrnambool Steam Packet Company.The Warrnambool Steam Packet Company was established in 1868 when capital was raised with 2000 shares at a value of five pounds each.It was established to provide passenger, accommodation and a large stock and freight service between Warrnambool and Melbourne.. At the time Stephen Henty was operating three steamers along the coast and at the prospect of losing his Warrnambool trade with the establishment of the new Warrnambool company, he sold one of his steamers , the Edina in March 1868. The first five directors elected were F P Stevens, J G Crammond, WW Jamieson, R B Paterson and George Wood. Fares were from one to three pounds and freight was 17 shillings per ton.The steamers connected with coaches from the north of Warrnambool as far as Hamilton. The cuttings record the financial position of the company for the first ten years. This collection of cuttings is valuable as a research item as it documents the development and operation as well as many of the stake holders in one of Warrnambool's earliest shipping companies. The cuttings are from a range of papers including The Warrnambool, Examiner, The Warrnambool Advertiser and the Argus.Ledger book with blue pages which is lacking the cover. It contains a number of cuttings which relate to the Steam Packet Company.Dated on first page: Monday November 1st 1869. Most of the cuttings are dated and some are from the Examiner. the Advertiser and Warrnambool Standard.warrnambool, warrnambool steam packet company, edina -
Kew Historical Society Inc
Archive (series) - Subject File, Authors (Kew), 1958
Various PartiesReference, Research, InformationKHS OrderReference file containing Sundry information about authors (poets, novelists, playwrights, historians, politicians, journalists) who were born, educated, lived or died in Kew, initially compiled by Society member Elizabeth Mackie who had previously researched the artists of Kew. Since the file was created, various items including correspondence and newspaper articles/cuttings have been added. Some information relates to organisations rather than individuals, such as that Kew was once the headquarters of the Fellowship of Australian Writers (1/317 Barkers Road). Within the file there is correspondence and curriculum vitae supplied by: Allan Aldous, Lillian Wood, Michele Nayman (1981), Yetta Rothberg (1981), Judith Rodriguez (1981), Rev Dr Arthur de Quetteville Robin (1982). The File also includes a photocopy of a letter supplied by Prof A D Hope (1981) relating to his memories of Kew. Authors mentioned in the file include: Allan Aldous, F G A Barnard, James Bonwick, Martin Boyd, Vincent Buckley, Sir Macfarlane Burnet, Anne M Carson, John Clements, Rita Erlich, Barbara Giles, Alison Goding, A D Hope, Wendy Jacobs, Lally Katz, Jill Manton, Philip Martin, James McAuley, Pauline McKinnon, Philip Mendez, Marrion Miller, Michele Nayman, Brenda Niall, Mark O’Connor, Nettie Palmer, Vance Palmer, Rev Dr Arthur de Quetteville Robin, Judith Rodriguez, Myra Roper, Dorothy Rogers, Yetta Rothberg, Frederick Sinnett, John Stanley, Peter Steele, W D Vaughan, Gwen Walker, J M Walsh, Lillian Wood.authors - kew (vic)authors - kew (vic) -
Melbourne Athenaeum Archives
Newspaper Cutting, The Fabulous Singlettes (musical) performed at the Universal Theatre commencing 11 January 1989
they also performed at the Athenaeum Theatre in 1987newspaper cutting in good conditionthe fabulous singlette, universal theatre, hocking & woods, wendy harmer -
Cobram Historical Society Inc
Wood plane
rectangular wooden frame with mortice hole for steel cutting blade held firmly by tapered woodern wedge -
Cobram Historical Society Inc
Wood plane
rectangular wood frame with 30 mm x 4 mm narrowed guide for planing with mortice cutting for 25 mm x 4 mm steel cutting blade attached to 190 mm long shaft held firmly by tapered wooden wedge -
Cobram Historical Society Inc
Wood plane
wooden frame with handles morticed into cutting frame and held firmly by wooden wedges to set where plane blade to cut, cutting blade is morticed in main wooden frame and held firmly by tapered wooden wedge -
Cobram Historical Society Inc
Wood plane
Wooden frame with morticed center with brass framed plate attached by 9 screws on top, steel frame plate on bottom is attached by 16 screws,cutting blade and wooden wedge for mortice center are missing -
Cobram Historical Society Inc
Wooden plane
Timber wood plane with steel blade with half moon cutting edge for tongue manufacture on timber surface, steel .blade is held firm by a tapered wooden wedge in a mortice cutting in plane block -
Cobram Historical Society Inc
Wood plane
Wood plane complete with mortice cutting to fit cutting blade and wooden wedge for grooving timber, Brass plate held firmly by 9 screws on top of mortice cutting guide. Steel plate guide on base is held firmly by 16 screws -
University of Melbourne, Burnley Campus Archives
Newspaper - Newspaper Cutting, The Illustrated Australian News, Sketches at the Horticultural Society Gardens, 1887
Photocopy of wood engraving illustration in "The Illustrated Australian News" January 8, 1887 p4. Composite of 6 views of the Gardens: 1. The Centre of the Gardens. 2. Curator's Cottage. 3. Pavilion. 4. Orange Grove. 5. Entrance to Orchard. 6. A Winding Path. Signed CSB. From the National Library of Australia.the illustrated australian news, gardens, cottage, curator -
Tatura Irrigation & Wartime Camps Museum
Wood Plane, 1940
Made by internees in camp 3 tatura & used there as a handtool for woowork/carpentryHandmade wood plane with metal pieces forming cutting blade at bottom ( blade exposed underneath)2 x one penny internement camp coins used as washers.Alex Mathieson & Son Warranted Cast Stell ( on metal piece)tatura, trades, tools -
Tatura Irrigation & Wartime Camps Museum
Wood Plane, 1940
Made by internee Camp 3 Tatura, used there as a handtool for carpentryWood Plane with turned & shaped wooden handle, metal pieces forming cutting/shaping blades.tatura, trades, tools -
Tatura Irrigation & Wartime Camps Museum
Wood Plane, 1940's
Made by internee at camp 3, Tatura and used there as a carpentry handtoolHandmade wooden carpentry plane with metal cutting/shaving centre plate. Base is roundedplane, wood, haering m, messerle t, camp 3, tatura, ww2, trades, carpentry -
University of Melbourne, Burnley Campus Archives
Photograph - Black and white print, Youth Employment Scheme Students in the Pavilion, 1939
In 1888 Joseph Bosisto, M.P. was presented with this collection of seeds by the English firm, Sutton's. He, in turn, presented the collection to the R.H.S.V. for permanent display. It remained on display at Burnley College until 1951. Note by E.B. Littlejohn 25.6.1992, This is part of the Youth Employment Scheme class 1939 with A.W. Jessep, Principal demonstrating use of secateurs in preparing cuttings."9 male students sitting at desks in a class. A male member of staff is standing in front of the group holding secateurs and a few pieces of scion wood. The wall of the classroom is covered with a display of Sutton's Seeds.On reverse, " 'The Age' and 'The Leader' 233 Collins Street, Melbourne."students, sutton's seeds display, joseph bosisto, m.p., rhsv, burnley college, youth employment scheme, 1939, a.w. jessep, principal, royal horticultural society of victoria, secateurs, cuttings, pavilion -
National Wool Museum
Newspaper Cutting, Messrs. C. J. Dennys and Co.'s New Wool Store Geelong, 10/9/1872
The Denny Lascelles Wool Warehouse was the first building in Victorian planned to facilitate storage, inspection and marketing of wool in one operation, and upon completion was the second largest store in the colony. CJ Denny's was largely responsible for establishment and development of the wool marketing industry in Geelong and is a figure of significance in the history of settlement in Geelong. The wool store, a basalt structure with cement rendered ornamentation, was erected for CJ Denny's and Co, in 1872 to the design of Jacob Pitman, Architect.Wood cut engraving of the Mesrs. C. J. Dennys and Co.'s New Wool Store Geelong, published in The Illustrated Australian News, 1872. The half page full colour illustration shows the newly constructed Wool Store with a bull drawn cart carrying full wool bales situated out the front of the store.Top margin: THE ILLUSTRATED AUSTRALIAN NEWS 201 Below image: Mesrs. C. J. Dennys and Co.'s New Wool Store Geelong Image signed, lower mid edge: WINSTON Image, on building: C.J. Dennys Wool Brokers 1872 C.J. Dennys & Co. Wool & Produce Warehousedenny lascelles wool warehouse, wool, dennys, wool store -
Old Colonists' Association of Ballarat Inc.
Photograph - Photograph - Colour, Ballarat Old Colonists' Association Homes, Charles Anderson Grove, Ballarat
... . Stripping of the wattle bark (for tanning) and the cutting.... Stripping of the wattle bark (for tanning) and the cutting ...HISTORY OF THE BALLARAT OLD COLONISTS' ASSOCIATION HOMES AT CHARLES ANDERSON GROVE, LAKE GARDENS One of the original objectives of the Association was “to provide the shelter of a house for those Pioneers of the Goldfields whom the reverses of fortune have deprived of the means of procuring the comforts of life in their declining years.” While the first home at Charles Anderson Grove was built in 1925 the Association had previously provided relief for needy pioneers from the time it was formed in 1883. Relief included monthly monetary payments, loads of firewood, medical assistance and distribution of Christmas boxes of groceries to deserving pensioners and in some cases payment of burial costs. Records indicate that in September 1922 three of the pensioners being assisted by the Association were accepted as residents in the newly erected Hassell Homes in Gillies Street (now demolished-opposite the High School). The first site for an Asylum for Indigent Members of the Old Colonists' Association was temporarily reserved from sale in October 1891. The site was approximately 28 acres in area in Mt Clear nearly opposite Midvale Shopping Centre in Main Road. The site was heavily timbered and when cleared over 260 tons of wood was sold to the Woah Hawp Gold Mining Company. A set of gates were erected but no homes built, although a plan for this reserve was drawn which showed twenty buildings ranging from one to four unit per building. The reserve was revoked in November 1909. The second site temporarily reserved in November 1909 as an Asylum was in Alfredton and consisted of some 7 acres and was adjacent to land reserved for an Abattoirs for the Ballarat Council. The reserve was revoked in February 1912 as it was deemed more appropriate to be added to the Abattoir site. Council suggested four (4) other sites in exchange for this land and they were inspected by the President, Vice President and Secretary on 22 December 1912. The first site inspected was land on the west side of Creswick Road opposite the brick kilns (now occupied by the showgrounds and oval). The land was described as being good quality, well fenced, no trees, good drainage and ample acreage but some distance from trams. The second site was Perry Park which was described as being good land, well fenced, having frontage to Gillies Street, good drainage and about 26 acres (but subsequently reduced to 10 acres). It was closely planted with Pinus Insignias and Wattle and had easy access from the Botanic Gardens tram. The third site was the North West portion of Victoria Park (corner of Sturt and Gillies Street) and was described as good land, well fenced and drained and well located. The fourth site was the South West corner of Victoria Park and known as Pound Paddock (corner of Winter Street and Gillies Street). It was considered to be low lying and too close to the Abattoir, and was also a considerable distance from trams. While the third site was recommended as the most suitable for the erection of homes it was considered unwise from the point of view as citizens to reduce the acreage of the park and therefore it was recommended that the Perry Park site be asked for as the most acceptable to the Association for the building of homes. The site was eventually temporarily reserved for an Asylum for Indigent Members of the Association in April 1914 with the gates from Mt Clear having been removed to the site a year earlier and eventually erected in 1917 for £12.10.0. In the same year the first 290 pine trees were advertised for removal in July and sold for £16. A sign indicating that the site was reserved for the erection of cottages was erected in September 1917. Stripping of the wattle bark (for tanning) and the cutting of the wood occurred in November 1918 with the land then being leased until it was required for the construction of the first homes in 1924. While the site was the third to be reserved it was the only one which was used for its intended purpose. It was named as Charles Anderson Grove in honour of Charles Anderson who joined the Association in 1918 and was President of the Association from 1942 to 1944. A number of cottages in the Ballarat Old Colonists' Association Retirement Village of Gillies Street, Ballarat.charles anderson grove, old colonists' club, ballarat, old colonists' association, old colonists' homes, retirement village