Sad-irons or "solid" irons were made by blacksmiths and used to smooth out material by pressing the hot iron over it. A piece of sheet -iron was placed over the kitchen fire and the irons placed on it could be heated whilst remaining clean of ash.. The women used 2 irons - one heating while the other was used. Thick cloth or gloves protected their hands from the hot irons. The handle was removed from the cool iron and re- attached to remove the hot iron from the fire. The cool iron was replaced on the fire or stove to heat again. These irons were cleaned with steel wool to prevent them marking the material. If the iron was too hot the material would scorch. Most homes set aside one day for ironing and some large households had an ironing room with a special stove designed to heat irons. However, most women had to work with a heavy, hot iron close to the fireplace even in summer. These sad irons remind us of the difficult circumstances experienced in their daily routines by the pioneers and early settlers of Moorabbin Shire The family of Miss M Curtis were early settlers in Moorabbin Shire. A) A heavy cast iron, flat iron with B) horseshoe shaped trivet stand c1880 The trivet can be attached to a table by an adjustable clamp.A) 5 on tip of ironsad iron, kitchen equipment, pioneers, early settlers, market gardeners, sewing, craftwork, clothing, moorabbin, brighton, bentleigh, fireplaces, stoves

Sad-irons or "solid" irons were made by blacksmiths and used to smooth out material by pressing the hot iron over it. A piece of sheet -iron was placed over the kitchen fire and the irons placed on it could be heated whilst remaining clean of ash.. The women used 2 irons - one heating while the other was used. Thick cloth or gloves protected their hands from the hot irons. The handle was removed from the cool iron and using the lifter the cool iron was replaced on the fire or stove to heat again. These irons were cleaned with steel wool to prevent them marking the material. If the iron was too hot the material would scorch. Most homes set aside one day for ironing and some large households had an ironing room with a special stove designed to heat irons. However, most women had to work with a heavy, hot iron close to the fireplace even in summer.These sad irons remind us of the difficult circumstances experienced in their daily routines by the pioneers and early settlers of Moorabbin Shire. The Curtis family were early settlers in Moorabbin ShireA) This heavy sad iron, made from cast iron, was heated over a fire or on a stove and used for pressing clothing and haberdashery. B) The separate tapered handle was used to lift the hot iron from the fire and when a "Potts" Handle was attached the ironing commenced. sad iron, kitchen equipment, fireplaces, stoves, pioneers, early settlers, market gardeners, sewing, craftwork, clothing, moorabbin, brighton, bentleigh

The (logging) truck carries a representation of John Glover’s painted landscapes, which Cox has painted on a solid block of wood. John Glover is one of Australia’s most celebrated colonial landscape painters. Born in England, he was a highly successful water-colourist and painter of landscapes in the tradition of French artist Claude Lorrain. Arriving in Australia in 1831, Glover adapted his picturesque style and luminous technique to his new surrounds, creating naturalistic and atmospheric paintings of Australian nature, settler life, and Aboriginal culture. Working out of doors, Glover developed an understanding of the unfamiliar Australian landscape, especially the twisting forms of native eucalyptus trees. His direct experience of nature, as both pioneer settler and painter, resulted in a new approach using a subtle palette of olive greens, ochres, misty greys and intense blues, and layered glazes of mauve, grey and gold, to portray Australian light and atmosphere. Dale Cox continues the ongoing preoccupation and tradition of landscape painting in the Nillumbik area and our impact on the environment in a contemporary way. The truck creates a playful nexus between painting (representational landscape) and sculpture, purposely bluring boundaries across these traditionally distinct disciplines. ‘Ghost’ seeks to convey the idea that when we remove something significant from a location, like the landscape itself, the remaining ‘place’ changes to become a new ‘place’. This may seem self-evident until we think more deeply about location and landscape. The white truck is a ghost, an ethereal, transient being that spirits away an entire place, forever removed from itself, and forever changed. Logging wild trees can never be like harvesting a ‘crop’. Logging removes a landscape, and changes a place forever. The ‘packaging’ of this painted landscape highlights the anomaly between commodity and our environment. Dale Cox was a local artist and this work was highly commended at the 2012 Nillumbik Prize. White plastic toy (logging) truck with a landscape painting on a wooden block. The landscape painting is reminiscent of paintings by colonial artist John Glover. N/Alandscape, truck, sculpture, environment, john glover, colonial, painting, ghost, nillumbik prize

A photo of the internment of the coffin of the Unknown Australian Solider in the Hall of Memory at the Australian War Memorial in Canberra. The coffin is flanked by pall bearers from each of the defence forces. The official Party, including the Prime Minister, Hon Paul Keating MP, looks on and veterans are seated. There are two Junior Legatees present, they were Rebecca and John Healey of Canberra. There was in article in The Answer newsletter in June 1994. The Unknown Australian Soldier was interred in the Hall of Memory on 11 November 1993. He was buried in a Tasmanian blackwood coffin, on which were placed a bayonet and a sprig of wattle. Soil from the Pozières battlefield in France was scattered in his tomb. The tombstone later placed on top of the tomb has the inscription: “An unknown Australian soldier killed in the war of 1914–1918”. At the head of the tomb is inscribed “Known unto God” and at the foot, “He is all of them and he is one of us.” (details taken from awm.gov.au)A record of Junior Legatees being present at the interring of the Unknown Soldier at the Australian War Memorial in Canberra. It shows how respected Legacy's work is by the wider community that the Junior Legatees are included in such a distinguished group at such an important event.Colour photo inside the Hall of Memory at the Australian War Memorial.australian war memorial, answer

Basket weaving and brush making was a source of income for those who worked in the workshops at RVIB and other institutions in New South Wales and Queensland. A diverse range products could be produced with cane, such as cane chairs, cots, washing baskets and trolleys, and the Institution sought to highlight these in the annual report. Over time the demand for, and supply of, cane changed - particularly during World War 2 when Asian sources were under attack or destroyed. At home, other materials such as plastics as well as the ability to import cheaper pre-produced products further reduced the demand for workshop pieces. This laundry basket was reinforced with a solid heavy base that gave it both strength and the ability to remain upright as clothing items were placed inside. This cane laundry basket made in the basket shop of RVIB for use in the organisation possibly between 1930-1940, not for sale. Held with staff in the Enterprises section since the move to 201 High Street in the early 1990s.1 cane basket with lidroyal victorian institute for the blind, employment

This fairly substantial wooden desk with vinyl top was issued to Wilson’s Promontory Lightstation by the Department of Public Works in the 1960’s. Primarily the desk was used for correspondence purposes, and now has the Bureau of Meteorology computer stationed on it. Although the design and make of this desk is common to many lightstations across Victoria, it is a good example of the kind of furniture that was provided to Victorian lightstations in the 1960’s. The solidly constructed desk was used in the lightstation office. It is made of honeycoloured hardwood and has a green vinyl top and three drawers on the left side. The style suggests that it may date to the 1960s. Gabo Island Lightstation has two identical desks, and all were probably standard issue from the Commonwealth Lighthouse Service or Public Works Office. Another twentieth century vinyl topped desk at Gabo is manufactured with a steel frame. Cape Nelson, Cape Schanck, Point Hicks and Gabo Island retain nineteenth century cedar desks. The desk at Wilsons Promontory has second level significance as a good example of the style of office furnishing provided to lightstations in the 1960s.Wooden desk with square legs and green vinyl top. It has three drawers with wooden handles on the left . The top drawer has a keyhole.

The style suggests that it may have been part of the fittings of the newly opened 1937 George V memorial building at Port Melbourne. Possibly hung in the Dining hall.Religious artSolid heavy wood panel carved in relief depicting 12 bearded figures, robed and seated around a table covered with a cloth. The table is laid with seven dishes, a loaf of bread, a wine cup in front of the central figure and a dish below the table on the floor at left, and a wine or oil jar at right. The sculptor has carved the wood in a style reminiscent of the medieval or early renaissance craftsmen. There are three modern steel screw attachments for hanging attached at verso on sides and centre top edge. The subject is the Last Supper of Jesus and his twelve disciples, with Judas at left end of the table seeming to cover with his hand a bag, perhaps the 30 pieces of silver.the last supper, jesus, disciples, carving, sculpture

This item was before diesel, electric and battery drilling apparatus were used by farmers, and other trades requiring a portable yet reliable method of drilling holes. As this item is a 3/4 inch hole drill it would be suitable for fencing and providing holes for structural studs. As with all outdoor farm equipment, man power was required (be it the farmer or farm hands). Fitness of the operator was at a high standard but protective gloves were not highly thought of as it was before occupational, health and safety regulations became mandatory over all manual handling activities, be they on rural properties or town/city factories. This period was one where the male ego was at its pinnacle i.e. the harder the tasks the more of a man was required. Hard manual work was not only the "way to go" but also a necessity. Evolution of cheap portable electric/battery powered tools opened up a more efficient method available, especially to those with less muscle strength.This item personifies the rugged environment of the rural workplace. The Kiewa Valley with its main emphasis on farming and grazing provided ample opportunity to use this construction implement. The manufacturer being a Scottish tool company is very significant in the era when this hole maker was in high demand. British steel products were of high grade and had a good record of reliability. The reliability of any tool was a solid factor for farmers and tradesmen in this semi-isolated region (Circa early 1900s) of the Kiewa Valley and its regional area. This factor,although not as crucial, post 1960s, when Asian manufacturers entered the market place and produced cheaper tools and transportation and supplies was more frequent and reliable, the need for the more expensive British made tools diminished considerably. After the influx of tradesmen from war torn Europe (post 1945) and the increased availability of tradesmen in the Kiewa Valley and its region the price of tools is not as crucial and the cost of all required tools has become a minimal part of the equation. It is only with the emerging younger trades person, farmer and grazier, who have more, "one eye on production costs" and no "old ties to the motherland" inert mind set that quality tools such as this auger and other hand tools "must be made to last a life time" is no longer part of the modern work environment.This cast iron hand operated drill, has a short barrel-shaped cylinder, known as "the eye" welded across the main rod and is 30mm in circumference. It also has a hole drilled to allow a screw to be fastened onto the hand stock ( not available).The main rod is solid for 400mm and then has been flattened and coiled (Helical screw blade) for another 200mm. At the end of the larger screw blade there is a smaller gauged starter blade with a pointer thread 15mm long. This Auger produces a 1/8th inch hole (metric measurement not used at time of manufacture) See KVHS 0469 for 3/4 inch hole and KVHS 0471 for another 1/8th inch hole.A number 5 stamped on the flat sideauger, hand drill, fencing, tool, rural trades, brace & bit

This item was before diesel, electric and battery drilling apparatus were used by farmers, and other trades requiring a portable yet reliable method of drilling holes. As this item is a 3/4 inch hole drill it would be suitable for fencing and providing holes for structural studs. As with all outdoor farm equipment, man power was required (be it the farmer or farm hands). Fitness of the operator was at a high standard but protective gloves were not highly thought of as it was before occupational, health and safety regulations became mandatory over all manual handling activities, be they on rural properties or town/city factories. This period was one where the male ego was at its pinnacle i.e. the harder the tasks the more of a man was required. Hard manual work was not only the "way to go" but also a necessity. Evolution of cheap portable electric/battery powered tools opened up a more efficient method available, especially to those with less muscle strength.This item personifies the rugged environment of the rural workplace. The Kiewa Valley with its main emphasis on farming and grazing provided ample opportunity to use this construction implement. The manufacturer being a Scottish tool company is very significant in the era when this hole maker was in high demand. British steel products were of high grade and had a good record of reliability. The reliability of any tool was a solid factor for farmers and tradesmen in this semi-isolated region (Circa early 1900s) of the Kiewa Valley and its regional area. This factor,although not as crucial, post 1960s, when Asian manufacturers entered the market place and produced cheaper tools and transportation and supplies was more frequent and reliable, the need for the more expensive British made tools diminished considerably. After the influx of tradesmen from war torn Europe (post 1945) and the increased availability of tradesmen in the Kiewa Valley and its region the price of tools is not as crucial and the cost of all required tools has become a minimal part of the equation. It is only with the emerging younger trades person, farmer and grazier, who have more, "one eye on production costs" and no "old ties to the motherland" inert mind set that quality tools such as this auger and other hand tools "must be made to last a life time" is no longer part of the modern work environment.This cast iron hand operated drill, has a short barrel-shaped cylinder, known as "the eye" welded across the main rod and is 30mm in circumference. It also has a hole drilled to allow a screw to be fastened onto the hand stock ( not available).The main rod is solid for 400mm and then has been flattened and coiled (Helical screw blade) for another 200mm. At the end of the larger screw blade there is a smaller gauged starter blade with a pointer thread 15mm long. This Auger produces a 1/8th inch hole (metric measurement not used at time of manufacture) See KVHS 0469 for 3/4 inch hole and KVHS 0470 for another 1/8th inch hole.auger, hand drill, fencing, tool, rural trades, brace & bit

John Nunn was one of the earliest brickmakers on record in Ballarat and has a road named for him - Nunn Street - where he resided..1) An oblong-shaped timber box open at top. Only butt joints are used. Iron strapping wraps around the vertical pieces of timber and across the top edge of the box. The longest pieces of vertical timber protrude past the end and are shaped like solid handles - one is broken. On each end piece there are small, blank iron plates held with screws. The base piece of timber is made from two different width weatherboard-style timbers. The nails in the base piece appear to be hand-made. Remnants of clay still line the interior. .2) Light brown brick. Please note: Brick mould and brick may be from different sources..1) Handwritten (possibly in ink) on one long side: MR H. G. SMITH ...(illegible) Ballarat .2) Imprinted: J. NUNNjohn nunn, j nunn, brick, mould, brick mould, industrial mould, brickmaker, ballarat, clay, ceramics

'Document Pathway' was commissioned for the entrance of the new Administration Building at Mount Helen. The University of Ballarat was renamed Federation University Australia on 01 January 2014. This item is part of the Federation University Art Collection. The Art Collection features over 1000 works and was listed as a 'Ballarat Treasure' in 2007.In 1993 Iain Reid wrote: "Document Pathway" Celebrating the presence of the University of Ballarat. The composition based on the proportions of a document. The document serves as a vehicle transmitting knowledge. Boarders of the document contain a structured pathway. It is solid in its base and growing aspiring to new levels and understanding. Marks on teh painting reflect an interest in Chaos theory. Through research random order is understood via measured knowledge. Surrounding the inner document lays the resource. A world to explore and enhance through knowledge. The surface of the painting investigates the aerial landscape placing the University of Ballarat within a physical location. The geometric structure demonstrating a peopled landscape where ideas create form. art, artwork, iain reid

In architecture a corbel serves a decorative as well as structural function as a solid piece of stone, wood or metal that is built into a wall and juts out like a bracket to carry a weight. The smoothly shaped corbel was formerly built into the external wall of the lighthouse facing the sea. It consists of two cupped, rounded forms, one bigger than the other, which are attached to a damaged flat base. Made of cast concrete, it is the same fabric as the lighthouse and shows evidence of white paint on its surface. An early architectural drawing of the tower shows the corbel as a projecting, decorative moulding underpinning the balcony floor associated with the auxiliary light. It indicates the original corbel was a much larger architectural feature which started as a solid rectangular block and terminated with a smaller block and then two tapering, rounded forms. Prepared in mid-1888, the architectural drawings for the lighthouse by Victorian Public Works Department architect, Frederick Hynes, were amended in 1888-89 to provide for an auxiliary light, which comprised an arched opening and door in the tower wall below the lantern room and small balcony. In the late nineteenth century all of Victoria’s lightstations installed a red auxiliary light to serve as a danger warning to mariners sailing too close to shoare. Existing lightstations, like Cape Otway, built a pavilion below their lighthouse facing out to sea, but newly constructed towers like Point Hicks and Split Point incorporated them into their designs. The efficacy of auxiliary lights became a controversial issue and all were discontinued on 1 January 1913. The Point Hicks balcony was removed from the face of the tower in 1971 after it was found to be badly rusted. This resulted in the complete removal of the corbel, from which the rounded moulding and part of the base survives. The auxiliary light and door were subsequently removed in 1975 and glass blocks now fill the opening. Cape Schanck Lightstation retains four cast iron brackets from its auxiliary light balcony which are currently stored in the lighthouse on the ground floor. No other architectural fabric associated with the auxiliary light has been identified at Point Hicks Lightstation. The fragment of corbel has first level contributory significance for its historic and architectural values as a relic of the auxiliary light and as an original moulding from the fabric of Victoria’s first concrete lighthouse.A masonary corbel.

A plastic, costume jewellery, fashion accessory for early 20th Century ladies Plastic is a material consisting of any of a wide range of synthetic or semi-synthetic organics that are malleable and can be moulded into solid objects of diverse shapes. Due to their relatively low cost, ease of manufacture, versatility, and imperviousness to water, plastics are used in an enormous and expanding range of products. They displaced many traditional materials, such as wood, stone, horn and bone, leather, paper, metal, glass, and ceramic, in most of their former uses including jewellery. Parkesine is considered the first man-made plastic. The plastic material was patented by Alexander Parkes, In Birmingham, UK in 1856.The world's first fully synthetic plastic was bakelite, invented in New York in 1907 by Leo Baekeland who coined the term 'plastics'. After World War I, improvements in chemical technology led to an explosion in new forms of plastics, with mass production beginning in the 1940s during World War 11 due to shortages of silk and ivory. A small, black plastic brooch with a verticle pin at back and diamante decoration .fashion, costume jewellery, personal effects, moorabbin, bentleigh, cheltenham, early settlers, jewellery, plastic

Jacqueline SLAYMAKER This work was undertaken in 1992 when Jacqueline Slaymaker was a 3rd Year student at Ballarat University College. The catalogue for the End of Year exhibition in 1992 states "The figures importance is purposeful. The strong sculptural form of the torso, tensions of the skin and volume are the aspects I focus on. Drawing is vital to my painting. The heavily layered works that I sand, scratch and rub back into eventually resolve some of the problems associated with painting. I believe this constant re-addressing creates a sense of history and building a texture creates a sense of history and build up of texture illustrates the concrete solid way I see the figure. I draw resource from ancient sculpture in particular Etruscan coffins and tomb wall painting. More recently I am interested in the draftsmanship of Jim Dine and monoprints of May Frank.' This item is part of the Federation University Art Collection. The Art Collection features over 1000 works and was listed as a 'Ballarat Treasure' in 2007.Framed life painting of a female nude. art, artwork, jacqueline slaymaker, nude, life study, oil on canvas, alumni, end of year exhibition

These boots belonged to Captain Charlie Rogers of the Australian Army who wore these and ceremonial regalia when he was part of the Guard of Honour during the visit of the Duke of Gloucester in 1934. The visit was part of Victoria’s centenary celebrations and the Duke officially opened the Melbourne Shrine of Remembrance. Rogers was a well-known Warrnambool identity in the 1930s, 40s and 50s as a horseman and an Army identity. He built a house in Birdwood Avenue, Warrnambool, in 1935 and was a long-serving Warrnambool Show official as a judge of equine events. Rogers died in 1961. These items are of great interest as examples of the boots worn by Army Lighthorse personnel in the 1930s. The mechanism for keeping the boots in good condition is of some technological interest. They are also of interest because they belonged to a well-known 20th century Warrnambool person. These are two knee-high brown leather boots with brown laces. The boots are slightly scuffed. Inside the boots are two pieces of red-striped canvas. The boots have wooden inserts to support the boots in storage. These wooden inserts, all varnished, are in four pieces - a solid foot shape to fit in the foot of the boots, two pieces shaped to fit the calf of the leg padded with green felt, one with slight indents at the top and the bottom and the other with a decided groove and the centre piece that has a hole cut out to fit the shape of the other two. This last piece has a wooden handle with a metal attachment. There is only one handle as it can be screwed out and fitted to either wooden insert. On the two wooden inserts ‘R ‘ for right and ‘L’ for left, marked twice on each insert.charles rogers, duke of gloucester, warrnambool

The stencil set has signs of use, with ink on the metal and paper stencils, and in the mixing lid and the block and tube of ink have been used too. The larger brush in this set is labelled "rubber set". The phrase is not to be confused with the 1900-1950s firm Rubberset but ''rubber set" is the process of setting the bristles of a brush into rubber to keep them together and hold them in place. This stencil set once belonged to Dr William Roy Angus. He habitually labelled his possessions with his name - this stencil set may have been used for that purpose. This set is now part of Flagstaff Hill’s comprehensive W.R. Angus Collection, donated by the family of Dr W R Angus, 1901-1970, surgeon and oculist. The W.R. Angus Collection: - The W.R. Angus Collection includes historical medical equipment, surgical instruments and material belonging to Dr Edward Ryan and Dr Thomas Francis Ryan, (both of Nhill, Victoria) and Dr Angus’ own belongings. The Collection’s history spans the medical practices of the two Doctors Ryan, from 1885-1926 plus that of Dr Angus, up until 1969. It includes historical medical and surgical equipment and instruments from the doctors Edward and Thomas Ryan of Nhill, Victoria. Dr Angus married Gladys in 1927 at Ballarat, the nearest big city to Nhill where he began as a Medical Assistant. He was also Acting House surgeon at the Nhill hospital where their two daughters were born. During World War II He served as a Military Doctor in the Australian Defence Force. Dr Angus and his family moved to Warrnambool in 1939, where Dr Angus operated his own medical practice. He later added the part-time Port Medical Officer responsibility and was the last person appointed to that position. Both Dr Angus and his wife were very involved in the local community, including the planning stages of the new Flagstaff Hill and the layout of the gardens there. Dr Angus passed away in March 1970.This stencil set is an example of objects belonging to Dr. W. R. Angus, 1901-1970, surgeon and oculist. It shows the keeness of the owner to label his posessions. The W.R. Angus Collection is significant for still being located at the site it is connected with, Doctor Angus being the last Port Medical Officer in Warrnambool. The Collection includes historical medical objects that date back to the late 1800s.Stencil set with 27 metal cut stencils of the 26 letters of the Alphabet plus an ‘&’, and a metal clip to hold the set together (.1 - .28). The set also has two wooden handled brushes (large with a purple band .29, small with grey band .30) a solid block of black ink and a tube of black paint (.31 and .32) in a green tobacco tin, and a round metal lid used for mixing the inks. The set is contained in a vintage wooden cigar box with a hinged lid. Another stencil (8452.33) is made from stiff waxed paper and reproduces the medical symbol [serpent wound around a rod or cross]. This set is part of the W. R. Angus Collection.Stamped on a large brush "PURE BRISTLE" "RUBBER SET" and a logo (looks like the head of an animal) On small brush "- - - ER" On the wooden box lid and inside the lid "EL VUELO" within a round logo with leaves, "MANILLA LEAF" and on the long side "PERLAS" "25" On wooden box end handwritten in pencil "STENCIL" On ink in a tin "The "GREYS" "SILK CUT VIRGINIA TOBACCO" On the round lid "‘Cellona’"flagstaff hill, warrnambool, maritime village, maritime museum, shipwreck coast, great ocean road, flagstaff hill maritime museum and village, dr w r angus, dr ryan, w.r. angus collection, stencils, stencil set, bristle brushes, rubber set brush, metal stencils, waxed paper stencil, black ink block, black ink tube, stencil ink, labelling equipment, el vuelo, manilla leaf cigars, the greys, virginia tobacco, silk cut virginia tobacco

This wooden juggling club or exercise club may also be referred to as a juggling pin. It is very similar in shape to a bowling pin or an Indian club. It dates approximately to the early 20th century. It may have been used as one of a pair for gymnastics or exercise, or part of a larger set used by a juggler for entertainment in a circus or carnival. At some time it may have been used with a ball or disc as part of a Skittles or bowling game set. The historical collection of Federation University Australia, Victoria, includes a very similar but slightly shorter club, labelled ‘timber skittle”, as can be seen in their photograph. Another example of very similar-shaped, same-sized clubs can be seen in the collection of Nobelius Heritage Park and Emerald Museum, Emerald, Victoria. JUGGLING Jugglers entertain audiences with their tricks and routines at events such as circuses, amusement parks, parties, shows on television or theatre, schools and parties. Juggles also compete at International Championships to obtain world records, performing as individuals or in groups or teams. Contemporary champion juggler David Cain performs a Juggling History Show that both entertains and educates his audience. His routines date from the early 1600s to the 20th century. He uses a wide variety of equipment in his acts including juggling clubs. EXERCISE Exercise clubs or Indian clubs were used in 19th century Victorian times as part of exercise or strengthening programs when they were swung in certain patterns and movements. Even in the early 20th century workplace a few minutes of Indian club swinging was common practice for the relief of tension. A video clip of an American school room in 1904 shows a group of boys and girls skilfully wielding clubs in an exercise sequence (see ‘Links” section). The 1904 and 1932 Olympic Games had an event called Club Swinging. Rhythmic gymnastics was added to the Olympic Program at the L.A. Games in 1984 where competitors use apparatus such as rope, hoop, ball, ribbon and clubs. The clubs come in a variety of weights and heights and have been used from the mid-1800s until around the 1930s in schools and military institutions. They are decorated in a variety of patterns and colours and some have feature lines or scored rings on them. This juggling club is significant for its association with education, entertainment and sport in the late 19th and early 20th century.Wooden juggling club (or pin, skittle or Indian club). Vintage, bottle-shaped club with a flat, slightly concave, base. Its turned, solid timber body tapers out from the base then in again to a very narrow handle with a round knob joined onto the top. Two concentric feature lines are scored into the wider part of club. It was possibly used in exercise, gymnastics or as a skittle. Sections of the club have two brown painted stripes; paint on the lower strip has been worn off at the base . There are remnants of white paint in two areas, possibly the remains of a maker’s name or decoration. There also appears to be an inscription stamped into the wooden handle but this is illegible. Late 19th to early 20th century.Remnants of what appears to be stamped lettering and painted labelling.flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, wooden skittle, entertainment, bowling skittle, wooden juggling pin, wooden juggling club, wooden exercise club, indian club, exercise club, club swinging, rhythmic gymnastics, sport equipment, juggling equipment, wooden club

The original Weatherly Library was situated in the space immediately on the left of the archway. The fittings and furnishing of the library was a generous gift in 1936 of Mrs H P Mackenzie of Trawalla in honour of her pioneer parents, Mr and Mrs William Weatherly. The library was panelled with blackwood and fitted with shelves intended to eventually house 3000 books. Specially made solid blackwood chairs, upholstered in genuine hide, two long reading tables, an upholstered bench seat under the north window and an ornate carved mantelpiece topped by a classical broken pediment framing a carved head of Minerva were also donated. In 1971 this library was no longer large enought o serve the growing number of boys at the college; it was replaced by a bigger, separate building, also known as the Weatherly Library. This building is currently in use, and recently renovated, as the senior staff room. In 1993 a third library building was opened and named Erindale in recognition of property associated with Clarendon PLC. In 2012 the school opened the Fraser Library on the senior campus in honour of old collegian and school council chair, Darrell J Fraser. Wooden frames with mounts and glass; both include printed descriptions; one includes a black and white photographh p mackenzie, weatherly library

Glasses, also known as eyeglasses or spectacles, are frames bearing lenses worn in front of the eyes. They are normally used for vision correction or eye protection. Pince-nez is a French style of spectacles, popular in the 19th century, that are supported without earpieces, by pinching the bridge of the nose. The name comes from French pincer, "to pinch", and nez, "nose". Although pince-nez were used in Europe in the 15th, 16th, and 17th centuries, modern ones appeared in the 1840s and reached their peak popularity around 1880 to 1900 A solid bridge piece is moulded to fit the curvature of the bridge of the nose. They are anchored onto the bridge of the nose via two small spring-loaded clips terminating in special nose-pads made from bone or tortoise shell on metal called plaquettes, which are tweezered apart for placement on the face through applying pressure to two small lever-like finger-pieces located on the front of the bridge. Plaquettes could be either hinged and flexible, permitting a better fit, or static as in the older examples of this type.. They were popular from the 1890s through to the 1950s, One half of a pair of lady’s Pince-nez eyeglasses with 1 gold rimmed glass lens , a gold style bridge and a fine gold chain that is attached to the side of the lens frame and to a shaped over- ear metal piece. eyes, spectacles, eye glasses, optometry, moorabbin, bentleigh, cheltenham, market gardeners, pioneers, early settlers, pince-nez

The Minimax conical fire extinguishers were manufactured until 1960 and then removed from the company’s product range. The earliest model had been produced with a simple handle made of folded pressed metal that is similar if not the same as that on the Point Hicks extinguisher. Later handles were moulded and had more substance to the way they were cut and then folded to form a solid grip. The Point Hicks Minimax extinguisher is an early model that probably dates from the years when these devices were demonstrated across parts of Australia. While numerous examples of the extinguishers survive in public and private collections in northern hemisphere countries, few appear to exist in Australian museum collections. However, the auction house records confirm that some do survive in private collections. The Point Hicks extinguisher was found by lighthouse keepers in 1974 buried in the sand in a flattened but surprisingly intact condition. It was beaten back into its original shape but the body still retains various dents. In 2010, AMSA located the extinguisher at the National Trust’s Polly Woodside historic ship museum and it is now at the Point Hicks Lightstation. The Minimax conical extinguisher has first level contributory significance as a historic item of early fire-fighting equipment from the lightstation that dates from the early twentieth century.Conical shaped brass fire extinguisher painted red with small nozzle at one end and a pump section at the other end. There is a handle on one side with closely spaced rivets down one side. Brass plaque with instructions attached to the body. There ia a square hook to hang the object form a wall or similar." ...ANKS ... / QUENCH.../ FOR FIRE / DRIVE IN PLUNGER / AT BIG END / ...ON GROUND /..../..../..."

This photographic equipment was manufactured by Eastman Kodak for amateur photographers. It enabled them to develop their films in a simple and effective manner. This box and contents have no known local provenance but are retained as an example of early photographic equipment. The items will be useful for display. This is a Kodak film tank development box and contents. The box is rectangular and wooden with a light brown polished surface. The sides of the box rest on a base that is slightly larger than the box sides. The lid is a separate piece and slots into ridges on the inside of the top of the box. Under the lid is a printed set of instructions on paper. Inside, the box is painted black and on one side it has an affixed metal piece for the attachment of the film spool. A removable solid cylindrical silver metal drum is inside the box. This has an outer covering of corrugated cardboard. There are three unattached pieces inside the box– two silver metal rods with handles and one silver metal rod with two larger end pieces. At the base of the inside is a piece of paper with instructions for use.Kodak Film Tank Kodak Film Tank B Time and Temperature for Tank Development Manufactured by Eastman Kodak Co. Pat: Aug 26, 02 May 23, 05 May 21, 07 Sep 17, 07 vintage photography equipment, warrnambool

See history of the Clarke family on Register 325-11.325-16 - Sepia photograph of three men talking on the ferry Alvina. Jack Spaven on the left, Mr Candy talking to Cpt Jimmy Clarke in the background. Taken 1930's. 325-17 - Small sepia photograph of Captain Jimmy Clarke. 325-18 - Sepia photograph of Captain George Clarke. 325-19 - Sepia photograph of three people on the S.S.Alvina. Captain Jimmy Clarke on the right, adjusting the gangway. Other people unknown. 325-20 - Sepia photograph in solid cardboard mount of the Clarke homestead in San Remo, Victoria. 325-21 - Small sepia photograph of Jack Clarke in 1901. 325-22 - Black & White photograph of Violet and Jack Clarke. Violet was Jack & Jimmy's sister.Some inscriptions written on by Arthur Woodley. 325-16 - "Taken in the 1930's, Mr Candy talking to Captain J. L. Clarke on "Alvina", Jack Spaven on left. 325-18 - "Daddy on way home at San Remo" - Capt. G. P. Clarke at San Remo. 325-19 - "Captain Jimmy Clarke, right, adjusting the gangway on S. S. Alvina 1920's - other people not known". 325-20 - "Our old home at San Remo". "Clarke's old home". "Home of Captain George Clarke. He dies 1904" 325-21 - "In 1901". "Captain Jimmy Clarke's twin brother. Jimmy would have been at sea then". 325-22 - "Jack& Vi at Punt Road, Sth Yarra". "Jack Clarke was Captai Jimmy Clarke's twin brother, Violet the sister".jimmy clarke, jack clarke, violet clarke, captain george clarke, jack spaven, mr candy, ss alvina, clarke's home san remo, arthur woodley

A wooden racquet with solid, and tapered, convex throat, cloth tape shoulder reinforcements, and medium grooved handle. Features early use of laminated wood strips, nailed to side of stem, and up along throat and lower head. This is also painted brown. Inscription across throat on obverse: TUNMER/"SPECIAL". Inscription across butt cover, in French: A.A. TUNMER/& CO.//PARIS/A GARDER SOUS PRESSE. Adhered onto the throat on obverse is a small metallic - possibly silver - monogram, possibly spelling the initials K.B. On the throat on reverse, is inscription in French and Latin: MARQUE DE FABRIQUE DEPOSEE/ATA/IN HOC SIGNO VINCES. Materials: Wood, Gut, Cloth tape, Ink, Glue, Lacquer, Leather, Metal, Painttennis

This white Toyota Corolla is one of the fleet of cars driven by Royal District Nursing Service (RDNS) Sisters to visit patients in the community to administer nursing care. 1985 was the centenary of the founding of the Melbourne District Nursing Society; founded in 1885; the Society was given Royal patronage in 1966 and became the Royal District Nursing Service. The Coat of Arms shown on the car was granted by the College of Arms in London in 1970. Royal District Nursing Service (RDNS) has had various modes of transport over the last 130 plus years. At first, from 1885 as Melbourne District Nursing Society (MDNS), their Trained nurses (Nurses) walked the streets and lane ways amid the slums of central Melbourne. As the Society expanded public transport was used, and bicycles were bought by the Society in 1903 and used in inner areas until 1945. During the Spanish flu epidemic, in 1919, MDNS appealed for assistance to procure Motor vehicles so the Nurses could visit an influx of cases. Through trusts, grants and donations four 'Ford T Model' cars were procured which enabled the Nurses to triple their visits. Through constant use the cars were in such a poor state two were sold in 1922 and the others later. In 1922-23 three Peugeot cars were purchased and a woman Chauffeur, 'Miss Sword', was employed who lived in the Home and was also in charge of the garage. MDNS was expanding and a Motor Auxiliary was formed in 1929 to take the Trained nurses (Sisters) to patients, and some Sisters used their own cars; even a motorcycle was used by one Sister in 1933. All these forms of transport were intermingled and in the early 1950s, and now as Melbourne District Nursing Service, seven Ford Prefect cars were bought followed by twelve Ford Anglia cars 1955. Having received Royal patronage; the now Royal District Nursing Service (RDNS) had its own fleet of Holden vehicles by the mid 1960s and the Motor Auxiliary ceased operating in 1971 as by then all staff employed were required to have a driving licence. Seat-belts had been introduced to Victoria in 1959 and District fitted them to their cars from 1962, even though they did not become compulsory until 1970. The Holden vehicles were replaced with grey Holden Torana vehicles. After several years the fleet was changed to white Toyota Corolla vehicles. The Melways Directory of maps was introduced in 1966, which was a boon to the Sisters, though it was a few years before it went beyond Seville, so a large paper map was used by the Sisters visiting patients in the areas passed Seville. By 2009 there were 598 cars in the fleet and the Sisters travelled 9 million 200,000 kilometres – this is equivalent to 12 trips to the moon and back. Coloured photograph of the side on view of a Royal District Nursing Service (RDNS).white Toyota Corolla sedan displaying the RDNS Coat of Arms on the upper centre of the front door. The car is the same width all over and the flat bonnet joins to a sloping large front windscreen. on the side, at the level of the windscreen are two windows, above the metal body work of both doors. The roof runs from the top of the windscreen to the rear of the vehicle where it joins with a short back window which sits above a short boot. Part of the front grill and headlights either side of it are seen, and a bumper bar below this. A black tyred wheel with solid hub cap is seen under a wheel arch in the body work, at the front and rear of the vehicle.melbourne district nursing society, mdns, royal district nursing service, rdns, rdns crest, rdns transport

In 1875, the Rocky Mountain Extended Gold Sluicing Company Ltd was created, utilising the previous Rocky Mountain claim for the area near Lake Sambell. The company employed A.L Martin to survey an area for a tunnel underneath Beechworth and Johnson Stephens to dig it. The tunnel was built at a rate of 40 feet a month and eventually measured 800 metres. The tunnel was a true accomplishment both in the present and during the 19th century. It was considered to be a marvelous engineering feat. Beechworth is renowned for its hydraulic sluice method of mining. This involved soil being exposed to torrents of water from high-pressure hoses. From 1876 until its closure in 1921, the mine produced an astounding 47,926 ozs of gold. Companies like this were the source of income for many Chinese gold-diggers who sought to make their fortune on the goldfields of Beechworth. During the height of the rush, the town had around 7,000 Chinese inhabitants living on the outskirts of town as they were not permitted to live within Beechworth itself.The search for gold is ingrained into the history of Victoria and therefore, images like this one which portrays an open-cut sluicing site can reveal important information for society and technology for the date when the photograph was taken. This image is of important historical significance for its ability to convey information about sluicing and the methods used to find gold in 1910. It also shows a location where sluicing was undertaken which provides insight into the impact of sluicing on the environment at a time when it was done. This image of the Rocky Mountain mine is historically significant as the mining complex is now non-existent, with the only remains being the tunnel built in 1880 by the company, which was considered one of the greatest engineering feats of the time. The image also provides a first-hand look into the social and cultural networks at play during the 19th century with racial segregation of the Chinese at the 'Chinese Camp', as well as an insight into Beechworth's origins during the Gold Rush.A sepia rectangular photograph printed on matte photographic paper as a postcardReverse: Historic Beechworth / 7792.1 / ROCKY MOUNTAIN MINE / Viewed from the “Chinese Camp”, shown partly in the foreground, we see the central plant of the famous Rocky Mountain Mining Company. This extensive complex, of which nothing remains, was situated between Silver Creek and the present Lake Sambell area. The company was responsible for a tunnel cut through solid bedrock underneath the town of Beechworth and surfacing near the keystone bridge on the Wangaratta side. Completed in 1880 it was declared to be one of the greatest engineering feats in Australia. The tunnel is still basically intact today. / Series by Wooragee Graphics: Historic Beechworth. / COPYRIGHT BURKE MUSEUM / No.72 beechworth, rocky mountain mine, sluicing, gold rush, mining, gold

The Northern Hawk-owl is a nomadic and generally solitary bird, although they can occasionally be seen in pairs. While these birds resemble owls, their behaviour is more similar to that of a hawk, hence their name. Normally active during the day (similar to the hunting habits of a hawk), they prefer to reside in boreal forest, grasslands, shrublands and temperate, cold and polar zones. Located in North America, Europe and Asia, these owls can also occasionally be found during migration, in the northern United States. There are three subspecies in North America, Central Asia and Siberia. At the present time (2021), its numbers are stable and so it is therefore considered of ‘least concern’ on the IUCN Red List, indicating it is not yet endangered. This particular specimen has been correctly mounted and presented as a relatively accurate representation of the actual bird. This specimen is part of a collection of almost 200 animal specimens that were originally acquired as skins from various institutions across Australia, including the Australian Museum in Sydney and the National Museum of Victoria (known as Museums Victoria since 1983), as well as individuals such as amateur anthropologist Reynell Eveleigh Johns between 1860-1880. These skins were then mounted by members of the Burke Museum Committee and put-on display in the formal space of the Museum’s original exhibition hall where they continue to be on display. This display of taxidermy mounts initially served to instruct visitors to the Burke Museum of the natural world around them, today it serves as an insight into the collecting habits of the 19th century.This specimen is part of a significant and rare taxidermy mount collection in the Burke Museum. This collection is scientifically and culturally important for reminding us of how science continues to shape our understanding of the modern world. They demonstrate a capacity to hold evidence of how Australia’s fauna history existed in the past and are potentially important for future environmental research. This collection continues to be on display in the Museum and has become a key part to interpreting the collecting habits of the 19th century.The Northern hawk-owl's face features white and brown soft feathery plumage and a dark brown border around its face/chin area, with a dark cream curving beak soft yellowy brown coloured eyes. Its front breast feathers are generally off white in colour with some flecks of brown. It has a long brown tail with off white banding, with creamy white claws. The owl has speckled brown and white plumage over the back of its body and wings and some areas of more solid brown are present around the back of its neck and top of wings. This specimen stands upon a wooden platform and two identifying tags hang from its right leg, while a metal numbered tag hangs from its left.Swing-tag: 38 / Rayed Swin Owl –/ See Catalogue, Page 53. Tag with faded script: No 33 Strix[?] / misarea[?] / Sweden[?] Metal tag - digits on metal tag appear to read, either ‘5028’ or ‘6028’taxidermy mount, taxidermy, animalia, burke museum, beechworth, australian museum, skin, reynell eveleigh johns, bird, surnia ulula, strigidae, northern hawk-owl, hawk-owl, canadian owl, hudsonian hawk-owl, owl, canada, asia, europe, north america

Ron White owned these jugs during his lifetime. Popular circa 1940s.Ron White owned these jugs. See KVHS 12821. Water Jug - tall glass jug with thin pale green 'plastic?' 'coating' wrapped around it. The cover has painted in colour -flowers and leaves. The lip is wavy with a clear plastic cover pulled over it. The handle is attached to the top half in the shape of an ear.The base is wider than the the top.Handblown. 2. Milk Jug - Unusual shaped small rectangular cream coloured jug with a handle at one end and a pouring lip at the opposite end. It sits on a four legged base and is decorated with coloured flowers and a cottage on each side. 3. Shaving Jug - Solid ceramic cream coloured jug with 7 holes in main area with a handle on one side and a pouring lip on the other. The jug is decorated with 3 small pictures of the countryside. The lip of the jug is defined in blue.1. Nil 2. At the base: "Hampton/ Ivory/ Swinnertons / England" 3. At the base: "Empire / Ivory ware/ England" and embossed also at the base "261 / England / 12?"ron white, ceramic and glass jugs, kitchenware, bathroomware