Eight page technical pamphlet, titled "Air Compressors for Automobile Service", published by Westinghouse Brake and Saxby Signal Co. October 1925. Manual No. D.P. 6 Saddle stapled with two staples. Covers air compressors for motor vehicles, including trolley buses. Shows the O35 compressor, M50 compressor and oil pump for the M50. Has photos of the various pieces of equipment."Colin Rutledge" stamped on top of page 1.trams, tramways, trams, tramways, westinghouse, trolley buses, compressors

Yields information about a compressor governor that is fitted to some Ballarat Trams, Westinghouse.Two A4 photocopied sheets, giving a side elevation of the Westinghouse "S-6-A Electric Compressor Governor" and the setting or the regulation and adjustment, installation and maintenance of the Governor. Commonly known as a "Bettleback" Governor. Dates from 1916. See Reg Item 703 for a MMTB drawing. WAD’s thoughts on setting Beetle back compressor Governors – 19/12/2009. Refer to instructions as well. Set both valves to approximately the same tension or thread length If when pumping up, both valves start to chatter, screw down the back valve further. When working satisfactorily, but pressures not right, that is, the governor is cutting out without valves chattering or with excessive range or pressure too high. Adjust the front valve until the desired cut out pressure arrived at. The cap must be on this valve for it to work. Adjust the back valve to adjust the cutting in setting, screw down for high cut in pressure. Adjust both as necessary to obtain your desires! And best of luck, it can be done, but is frustrating!!!!!trams, tramways, governors, westinghouse, air compressors, instructions

Red covered auction catalogue for a sale held at the works of Gold Dumps Pty. Ltd., Eaglehawk on the 8th and 9th September, 1959 of Sand Treatment Machinery & Plant. Sale held at the Devonshire Sands Site and the New Moon Site. Included in the sale were 2 Oliver Filters, Large Assortment of Pumps, Pomona Pump, Electric Motors, Air Compressors and Receivers, Assay Equipment, Piping & Pipe Fittings, Steel Water Tanks, Buildings, Tools, Huge Quantity Scrap & Accessories. J. H. Curnow & Son Pty. Ltd. Were the Auctioneers. Catalogue, a Bolton Bros. Print. Auctioneers Copy written on the top of the front cover. Prices of lots have been written near the lots.business, auctioneers, j h curnow & son pty ltd, ian dyett collection - auction catalogue - gold dumps pty ltd, j h curnow & son pty ltd, devonshire sands site, new moon site, bolton bros print

Red covered auction catalogue for an auction sale held on 10th December, 1958 at the Sunbeam Colleries, Korumburra of Coal Mining Plant. Lots include Electric Winches, Jaques Crushing Plant, Air Compressing Plant, 15-ton Avery Weighbridge, Corr. Iron Buildings, Rails, Pumps, Electric Motors, Piping, Stores, Engineers and Blacksmiths Plant, Pneumatic and Hand Tools, Valuable Electrical Equipment and Costly Accessories. There are descriptions of some lots. J. H. Curnow & Son Pty. Ltd. Were the auctioneers.business, auctioneers, j h curnow & son pty ltd, ian dyett collection - auction catalogue - sunbeam colleries, j h curnow & son, prahran telegraph printing co pty ltd

Red covered auction catalogue with black printing for a sale at C.R.A. Research Unit, Eastville, Vic on 27th March 1985. For sale was Pump Setting Rig skid mounted with 12,000 lbs. Thomas Winch with 5.5 K.W. 415 V. 3 HP Electric Motor & 100m of Cable, 1981 W.B. Holden 1 Tonne Utility, Massey Ferguson 290 Tractor, 75 KVA McFarlane Generator with 6 Cyl. Diesel Motor on Tandem Trailer, Alum. Site Workshop, Steel Ships Container, 2 Uniroyal Static Storage Tanks each 50,000 gallons (U.S.), 13 Groundfos Electric S.S. Submersible Pumps, Portacom Toilet, Thousands of Metres H.D. Electrical Cable, Air Hose, Steel Flanged, Drill & P.V.C. Piping, Assorted Tools, Electrical and General Equipment. J. H. Curnow & Son Pty. Ltd. Were the auctioneers.business, auctioneers, j h curnow & son pty ltd, ian dyett collection - auction catalogue - c.r.a. research unit - eastville vic, j h curnow & son pty ltd, f c dyett, i m dyett, n f dyett, bolton bros pty ltd print

One of a few service vehicles built from almost new by the MMTB rather than being a converted vehicle. Donated to the BTM in 1999 and has been an operational tram 2001.Single truck (4 wheels), special purpose tram fitted with two cabs, control equipment, air brakes, track scrubber or cleaning equipment, pump, water and air lines to clean track. Carries approx. 4 cubic metres of water. The tram was built by the Melbourne and Metropolitan Tramways Board in 1934 using the cabs from a C class tram (No. 32). It was transported to the isolated Footscray system a number of times to clean the rails there. In 1961 it received additional body bracing and repainted in the diagonal black and string (light cream) stripes. The tram became 8W during 1975 as the then new Z class trams came into service. By the early 1990's the need for the tram and the other similar cars used to "scrub" the surface of the rails was no longer. The tram was stored at Malvern depot for many years before being donated to the Ballarat Tramway Museum by the Public Transport Commission in September 1999. It has been scrubbing the rails in Ballarat since March 2001. For a detailed article see April 2008 issue of Fares Please. Photo Warren Doubleday 20/9/2008 after painting completed See Destination CityMMTBtrams, scrubber tram

The heavy twin tanks formerly contained vaporised kerosene which was used as a fuel to light the lantern. Kerosene became available in the 1860s as the oil industry in the United States developed, and vaporised kerosene soon became the most common system of illumination. The kerosene vapour lamp was perfected by Chance Bros. for burning the light in their renowned lenses. The system involved vaporising kerosene under pressure and mixing it with air and then burning the vapour to heat an incandescent mantle. The lamp had to be watched throughout the night in case a mantle broke, and the tanks needed to be maintained by hand-pumping each hour or so. Kerosene tanks like these were developed in the early twentieth century, and kerosene as a fuel was phased out by electricity, with the last kerosene system in Australia eventually replaced in 1985. The wick lamp in Gabo Island’s light was altered to a vaporised incandescent kerosene mantle burner in 1909. They would have been in use until 1935, when the light was electrified and the original first-order lens was replaced by a fourth-order lens. The Gabo Island tanks, which are presumed to be those used in the lighthouse between 1909 and 1935, are not attached to the optical apparatus and are no longer in the lighthouse. They are also missing the pressure gauges that were formerly attached to the top of each cylinder. Cape Schanck has a pair of unattached tanks, which are not historically associated with the lighthouse. Point Hicks has an iron stand that formerly supported its lighthouse oil tanks. Despite their lack of intactness, the Gabo Island tanks have first level contributory significance for their provenance to the lightstation and historic association with the lantern’s original Chance Brothers first order lens, which was removed in 1935Two large green cylinders standing in a metal frame. There is also a pumping mechanism attached to the stand with a wooden handle.

Was the stand for a Chance Brothers air & oil containers fitted with pump handle & pressure gauges.This type of installation was once common and relied on the lightkeeper having to pressurise the cylinders manually at regular intervals throughout the hours of darkness. The oil was fed under pressure to the burner mantle. It is all that remains of an air and kerosene oil tank installation, with each rounded side formerly supporting a heavy iron tank. The containers would have been fitted with a pump handle and pressure gauges. An intact assemblage is displayed in the AMSA offices, Canberra with a text that explains ‘This type of installation was once common and relied on the lightkeeper having to pressurise the cylinders manually at regular intervals throughout the hours of darkness’.The system involved vaporising kerosene under pressure and mixing it with air and then burning the vapour to heat an incandescent mantle. The use of kerosene as a fuel to light the lantern became the most common system of illumination from the 1860s after the oil industry in the United States began to develop. The kerosene vapour burner was created in 1901 by British inventor Arthur Kitson (1859-1937) and perfected by Chance Bros for burning a more intense light in their renowned lenses. The lamp had to be watched throughout the night in case a mantle broke, and the tanks needed to be maintained by hand-pumping each hour or so. The Point Hicks lantern was initially lit by a six-wick Trinity house kerosene burner. This was replaced by the more efficient and brighter 55mm vaporised kerosene mantle burner in 1905, and the tank stand is probably original to this apparatus. Electricity eventually replaced kerosene at Point Hicks in 1964 making the tank installation obsolete, and the last kerosene system in an Australian lighthouse was replaced in 1985. Gabo Island Lightstation has a pair of tanks that are not attached to the optical system and are no longer in the lighthouse. They are also missing the pressure gauges that were formerly attached to the top of each cylinder. An intact tank assemblage is displayed at the Cape Schanck Lighthouse Museum it is detached and not original to the lighthouse. Although corroded, the remnant Point Hicks tank stand has first level contributory importance to the lightstation. It is significant for its provenance and historical value as part of the Chance Bros vaporised kerosene burner introduced in 1905 to intensify the light and improve the efficiency of the system. The rusted iron stand rests on four short legs and is shaped like a pair of spectacles.

This chainsaw was one of the earliest models sold in Australia. It was manufactured by the Lombard company which was established in 1894 when Nathaniel Lombard developed the first practical water wheel governor in Roxbury, Massachusetts, USA. In 1904, the company moved to Ashland, Massachusetts. During the first World War, Lombard Governor produced hydraulic lathes for the manufacture of artillery shells At the conclusion of the war, Lombard expanded into the areas of chain saws and plastic molding injection machines. This model, the L-30 was only produced for 2 years from 1962 - 1964, primarily due to safety concerns and the fact that it did not have any way to sharpen or tighten the chain. This chainsaw was sold by Mann of Wodonga and donated to the Wodonga and District Historical society by David Mann, owner and manager of Mann Wodonga.This item is significant as it was produced for a limited time. It was also sold by a prominent Wodonga business.A single operator chain saw from Lombard, Ashland, Massachusetts, USA. The chainsaw was relatively lightweight but had no safety features such as a chain brake. It was made primarily of sand cast magnesium. The main cylinder was constructed of aluminium with a cast iron sleeve. It had a manual oil pump, the crankshaft operated on ball bearings and it had a maximum rpm of 4,500. See the Model profile in the accompanying Media item for details.On side of fuel tank: "ONE HALF PINT/SAE-30 OIL/ FOR EACH/ GALLON GASOLINE/ MIX WELL IN SEPARATE CONTAINER/BEFORE FILLING" On opposite side: "STARTING INSTRUCTIONS 1: FILL FUEL TANK WITH PROPER FUEL MIXTURE ( AS NOTED ON TANK) 2. FILL OIL RESERVOIR WITH #30 MOTOR OIL 3. CLOSE CHOKE, MOVE LEVER BACK TOWARDS AIR FILTER 4. HOLD THROTTLE WIDE OPEN 5. PULL STARTER HANDLE SLOWLY UNTIL STARTER ENGAGES, THEN GIVE IT A SHARP YANK 6. AS ENGINE WARMS UP, EASE CHOKE LEVER TO OPEN POSITION"hand tools, vintage chainsaws, david mann, mann wodonga

FLETCHER RUSSELL & CO. LTD/ WARRINGTON MANCHESTER & LONDON Thomas Fletcher (1840-1903) had established a gas appliance manufactory in Thynne Street, Warrington by the 1880s. By 1895 the company had become Fletcher Russell and Co Gas Engineers, his firm having merged with Alexander and William Russell of Pendleton Iron Works. In 1950, the firm merged into Radiation Ltd which was later acquired by 'TI New World. In the early 1880s Thomas Fletcher was a registered dentist who went on to found a dental apparatus manufacturing business. He later diversified into producing equipment for blacksmiths, foundries, forging and other sectors. The company had grown to 900 employees in 1914. These foot-operated bellows were for pumping gas to keep the patient relaxed while the dentist worked on their teeth. They were later modified for a variety of uses where a continual flow of air was needed.These bellows are representative of a range of devices developed in the late 19th Century to assist in manufacturing. They were donated to our collection by a Wodonga resident.A set of foot bellows made from timber, metal and leather. The bellows were activated by pressing up and down on the metal step-shaped lever at the front. The air outlet on one side would have a hose attached to it to direct the air current to wherever it was needed. The bellows are made from leather. The manufacturers mark is attached to the top within a metal circle.On top of Bellows in a circle: "FLETCHER RUSSELL & CO./ WARRINGTON/ MANCHESTER / LONDON"foot bellows, fletcher russell & co. ltd.

BHS CollectionA Davis Tyre pump. A black metal cylinder four centimetres diameter and 48 centimetres long is attached to a metal plate four centimetres wide and 14 centimetres long. A one centimetre diameter, 50 centimetre long rubber hose is attached to the bottom of the cylinder has a metal fitting on the other end. The wooden handle on top of the cylinder is 17 centimetres long and three centimetres diameter, it has a one centimetre diameter, 44 centimetre long metal rood attached to the middle of it which goes into the cylinder and presumably has something on the end of it to push air through the rubber hose. The logo near the top of the pump is partly destroyed has on it - 02 (an unreadable word) DAVIS TYRE PUMP. (There is a picture of The Davis Cup tennis trophy in the middle) Partly destroyed on the bottom of the logo is - DAVIS INDUSTRIES AUSTRALIA Part of the Aileen and John Ellison Collectionaileen and john ellison, davis tyre pump

Heavy card sign printed in black. Code of Signals, including winding, pumping, interplat signals. Firing Signal printed across middle of sign. Winding signals: 1 Stop when in motion, 1 Heave up, 2 Lower, 3 Hold fast! Danger, 4 Men on, 6, Cage at liberty, 7 Change Tanks or Cages, 8 Put drum in or out of gear, 9 Turn Air on or off, 10 Accident, 15 Serious Accident. Firing Signal 4 pause 3 - holes charged ready to fire, 1 Heave up.Boltons Print, Bendigobendigo, mining, code of signals

This bellows was used at the Warrnambool Racecourse by Master Farrier, Brian Chapman (1931-2017), during the 1970s but its history before then is still being investigated. The bellows have continued to be used from 1978 at Flagstaff Hill's blacksmith's workshop. Even today, in 2021, this same bellows are used by a volunteer blacksmith as he demonstrate the skills and tells of the importance of the blacksmith trade to colonial Australia. This 1860s double-action bellows is a typical form of blacksmith's or shipsmith's bellows. The end is forge-fitted with an iron nozzle or tube, called a tuyere or Tue iron, which concentrates the air to fan the fire or furnace. Tuyeres were traditionally made of cow horn. The double-action design of this bellows efficiently moves air both in and out of the chambers in the one movement of the long handle. The bellows was manufactured by John C. Onions of Birmingham, England, between 1862 and 1875. The stamp with the text, Gold Medal 1862, was also used on the business’ advertising. In 1875 the company was registered and began using the name John C. Onions Limited. JOHN C. ONIONS - John C. (Collingwood) Onions (1841-1904) was the son of a bellows maker of the same name. Onions (born 1841) and his wife Helen married in 1867 and they named one of their children John Collingwood Onions (1868-1913), as was the family tradition. He was well known as a Birmingham manufacturer of patented bellows and other forge-related equipment. He sold to the wholesale and retail markets for both local and overseas customers, including the British colonies. An 1862 advertisement points out that John C. Onions was a “Bellows manufacturer and contractor to Her Majesty’s Honourable Board of Ordinance” and His Imperial Majesty the Emperor of the French [Napoleon Bonaparte]”. The advertisement includes a sketched portrait of the Emperor Napoleon III, and an Imperial Autograph Letter dated May 23, 1854, from Napoleon, Palace of the Tulleries to Mr J C Onions of Bradford Street, Birmingham. In 1863 the company registered a patent on portable forges. In 1871 there were eight employees. John C. Onions Limited became a registered company in 1875. In 1876 an advertisements included that the company were smiths for hearths and tools in general and showed a row of six medallions including one with “Napoleon III, Emperor” and his portrait, and another “ _ _ _ 1862 MEDAL”. Their advertising motto was “For Excellence of Quality”. In 1885 the company merged with William Allday and Sons to become Allday and Onions. This mid-19th century bellows has local historical significance as it were once used by blacksmiths at the Warrnambool Racecourse in the annual racing event that continues today. This bellows is significant as a working example of equipment used in the 1800 and 1900s in the trace of blacksmiths and other metal working smiths. The bellows is technologically significant as it shows the progress from simple bellows to the double-action bellows, a time saving and efficient improvement. The manufacturer John C. Onions is historically significant as a family business that began in the 1600s and continued up until the 1980s.Bellows; large, oval, mechanical double-action smith’s bellows, manually operated, in working condition. The paddles of wood that form the top, middle sections and base of the bellows have flexible leather pieces attached firmly between them, forming airtight double lungs. Cut-outs in the panels allow the bellows to fill with air then force it out. A long handle is connected to pump the bellows and control the quantity and force of the air. The blasts of air are forced through the metal nozzle or tuyere at the end of the bellows and into the forge’s fire. Inscriptions are impressed into the wood on the upper paddle or board of the bellows. There are three circular stamps containing text. Text impressed in the wooden upper paddle of the bellows has been assumed to read “JOHN C. ONIONS, PATENTEES & MANUFACTURERS, BIRMINGHAM””?” “EXTRA” “AWARDED FOR EXCELLENCE OF QUALITY”, made from the following readable text :- “JOHN C ONIONS“ “PATENT - - - & MAN - - - - - - - - -“, “BIR - - - - HAM“, “ _ ERA - - - - “- XTRA-“, “- - - - - - - FOR EXCELL-“ “OF - - - - ITY” Text in the stamp “ - - ECE - - “, “ - - - - - / 1862 / MEDAL”, “- ITY” flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, john collingwood onions, john c onions, allday and onions, bellows, smith’s bellows, 19th century bellows, double-action bellows, double-acting bellows, double lung bellows, double chamber bellows, blacksmith tools, blacksmith trade, blacksmith craft, blacksmith equipment, forging equipment, john c onions patented double-action bellows, brian chapman, warrnambool racecourse, blacksmith, shipsmith, iron smith, mechanical bellows