This bell was used by the public to ring encouragement to participants competing in the Kangaroo Hoppet. The Kangaroo Hoppet has its origins in the Birkebeiner Nordic Ski Club's 21 km Australian Birkebeiner, first held in 1979 at Falls Creek. In 1991 the first Kangaroo Hoppet of 42 km was conducted and became part of the Worldloppet being the first and, at the time, the only one in the southern hemisphere. It continues (2024) to be held on the fourth Saturday in August. It also includes the Australian Birkebeiner 21 km and the Joey Hoppet 7 km.Used by local family to cheer on relatives competing in the 1995 Kangaroo Hoppet at Falls Creek.Metal cylinder fastened with 3 metal rivets with metal ring handle on metal top. Attached is a metal ringer and a white ribbon with blue writing and boomerang and skis logo. Handmade.Ribbon: "AASF Falls Creek 1995"kangaroo hoppet; ski race; cross country skiing; bogong high plains, snow sports, metal bell

ring bound non-fictionFamily history of Henry McCurry and Elizabeth Lindseymccurry, family history

One of a collection of 7 photographs of amygdales polished by Dr G Baker CSRO 1950. A fully coloured plate of the originals was to have appeared in the book "Phillip Island in Picture & Story".Black & White photograph of an Amygdale Stone - outer ring and inner ring with patterned centre."Phillip Island Amygdale magnified 5 diam. Colours red & yellow."phillip island, amygdale stone, dr g baker, joshua w gliddon

Bell used by the conductor to signal to the driver to stop, proceed or an emergency stop. The flat leather strap indicates it was used on a cable tram, rather than an electric tramcar which were fitted with round leather cords. The leather strap is riveted to a round steel ring.Demonstrates a conductors communication or signal bell made for use on cable trams.Brass Conductor Communication Bell, or signal bell, consisting of cast frame, bell striker and bell pull part. Has at both ends, four open screw holes that were used to secure the bell to the roof of a tram with a flat 22mm wide leather strap attached using a steel ring.trams, tramways, conductors, bells, cable trams

Probably of US origin Can , Meat (Mess Kit), M-1910, M-1918 The older style mess kits had the flat lid that could also be used as a plate. The M-1932 (not unit in our collection) unit had the plate divided into two sections so food could be separated. The folding handle, when closed, fits into the groove formed by the divider. The ring on the plate was moved to the end of the groove so the lip of the handle fits right into it. The M-1932 Meat Can was made of "corrosion resistant" galvanized steel, not aluminium. It used the same WW I style narrow profile steel handle attached by a cast hinge.Oval aluminium mess kit with steel handle which acts as a lid lock when folded. Cover has a mounted bracket for a ring fitting for attachment to belt.Nilmess kit, m-1918, m-1910

VEMU1615.1 The 2 rings are elongated horizontally and have an axial length of 11cm. The shanks are 10cm long. VEMU1615.2 The rings are 8.7cm diameter, and the shanks are 9.7cm long. VEMU1615.3 The rings are 6.3cm diameter, one ring is circular and the second has a pointed end. The is 12cm long. VEMU1615.4 The rings are 6.2cm diameter, and the shanks 8.4cm long.

Aluminium Seal Covering Lid Berry Styled Border around the Writing/text(Leaf styled ring Border around bottle) Superior Raspberry Cordial

Black powder splitting guns were commonly used to split large logs into more manageable pieces before the advent of excavators and front-end loaders in bush logging operations. A typical splitting gun used in Victorian forests was a piece of high-grade steel about 1-1/2 to 2 inches in diameter and about 16 inches long, and slightly tapered at one end. They had a ¾ inch hole drilled about 9 inches deep into the centre of the shaft with a small pilot hole drilled from the outside to load the fuse. The tube was carefully loaded with an amount of black gunpowder using a funnel and spoon. Experience being the guide on how much powder to use, which depended on log size, species and difficulty of splitting the wood. The hole was stopped with a piece of wadded paper and the gun positioned at the end of a length of the log to be split. The splitting gun was then belted into the log with a large wooden maul or even the back of an axe to a depth of about 3 to 4 inches. There were often markings as a guide. This also had the effect of tamping the black powder inside the gun. Preferably the gun was backed up by another large log to absorb the shock and avoid it flying off in the bush somewhere. I have seen guns where a length of string and coloured flag could be attached to help find them. A length of fuse was then inserted in the small hole and lit. Kaboom !!!! Needless to say, the splitting gun was a dangerous implement.Commonly used to split pulpwood but now rareBlack Powder Splitting GunFive marking rings used to guide how far the gun was in the logforest harvesting

Black and white photograph of two men in a butcher's shop, one standing behind counter, the other in front of the cool-room door.On back of photo: "Doug Warren, Ring ? | Butchers shop, Main St."butchers shop, main street, doug warren, butchers

Legacy have many programs to send young junior legatees on activities, camps and outings. This photo shows children standing under a Legacy logo with Santa and two photos of children from that group with Santa. The logo imprinted on the back implies it was December 1999. It was stored with other photos of Junior Legatees from the 1980s and 1990s. A record of a Legacy providing experiences for the junior legatees.Colour photo x 3 of junior legatees at a Christmas party.Printed on Kodak paper with Olympic rings 'Official sponsor of the Olympic Games'.junior legatee outing, christmas party

Large wooden horizontal shaft with two metal rings at either end and large centre rings.transport, animal, rural industry, livestock