Showing 319 items
matching lamp glass
-
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Lights, paraffin lamp c1950, c1950
A flat-wick lamp is a simple type of kerosene lamp, which burns kerosene drawn up through a wick by capillary action. A flat-wick lamp has a fuel tank (fount), with the lamp burner attached. Four prongs hold the glass chimney, which acts to prevent the flame from being blown out and enhances a thermally induced draft. The glass chimney needs a "throat," or slight constriction, to create the proper draft for complete combustion of the fuel; the draft carries more air (oxygen) past the flame, helping to produce a smokeless light which is brighter than that produced by an open flame. The lamp burner has a flat wick, usually made of cotton. The lower part of the wick dips into the fount and absorbs the kerosene; the top part of the wick extends out of the wick tube of the lamp burner, which includes a wick-adjustment mechanism. Adjusting how much of the wick extends above the wick tube controls the flame. The wick tube surrounds the wick, and ensures that the correct amount of air reaches the lamp burner. Adjustment is usually done by means of a small knob operating a toothed, metal sprocket bearing against the wick. A paraffin lamp with a green metal base to hold fuel with a side screw to adjust wick length. An opaque white glass shield sits in a metal frame attached to base* moorabbin, bentleigh, cheltenham, pioneers, early settlers, market gardeners, lights, lamps, paraffin, oil lamps -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Lights, Victorian kerosene banquet lamp, c1900
... source, protected by a glass chimney or globe; lamps may be used... source, protected by a glass chimney or globe; lamps may be used ...The kerosene lamp is a type of lighting device that uses kerosene as a fuel. Kerosene lamps have a wick or mantle as light source, protected by a glass chimney or globe; lamps may be used on a table, or hand-held lanterns may used for portable lighting. There are three types of kerosene lamp: traditional flat wick, central draught (tubular round wick), and mantle lamp. The side screws adjust the length of the wick and hence the strength of the flame / light produced. Prior to the introduction of gas and electricity these lamps provided light in households after sunset.Prior to the introduction of gas and electricity these lamps provided light after sunset for the early settlers, as they established their farms and businesses, in Moorabbin Shire.A Victorian kerosene banquet lamp, with a gilded metal quad footed base, cranberry glass oil reservoir with geometric patterns, original etched, yellow, glass globe shade and clear glass chimney. There are 2 side screws for adjusting the flame.early settlers. pioneers, follett w, moorabbin, bentleigh, brighton, ormond, market gardeners, kerosene, paraffin, lights, lamps, candles -
Federation University Historical Collection
Photograph, Clare Gervasoni, Stained Glass window at the Ballarat School of Mines, 04/2020
... , the miners lamp and two hammers. Their is also stained glass ...The Ballarat Technical Art School building was opened in 1915. It is not known when the stained glass was put into position.Colour digital photograph showing the stained glass at the Ballarat Technical Art School. The mining lamp detail is on the entrance door to the Ballarat School of Mines Technical Art School building. The design features three tools associated with mining, the miners lamp and two hammers. Their is also stained glass on the entrance doors and a window by the entrance.ballarat school of mines, ballarat technical art school, stained glass, miners lamp, entrance -
Federation University Historical Collection
Photograph, Lisa Gervasoni, Stained Glass window at the Ballarat School of Mines, 2006, 30/06/2006
... art school stained glass miners lamp Lisa Gervasoni ...The Ballarat Technical Art School building was opened in 1915. It is not known when the stained glass was put into position.Colour digital photograph showing the stained glass detail on the entrance door to the Ballarat School of Mines Technical Art School building. The design features three tools associated with mining, the miners lamp and two hammers. ballarat school of mines, ballarat technical art school, stained glass, miners lamp -
Federation University Historical Collection
Equipment - Scientific Instument, Globes, 20th Century
Most were used in various capacities at Ballarat School of Mines or University of Ballarat.Assorted lamps including Edison Carbon filament light bulbs and other special purpose lamps, .1-3) Robertson, pear shaped 220 V 16, carbon filament? bayonet light bulb with 'nipple'. .4) Ediswan, standard shaped, 928, carbon filament? bayonet light bulb with 'nipple'. .5) (B in a circle) 280 V 32 oo1A, pear shaped, carbon filament? bayonet light bulb with 'nipple'. .6-7) Crompton? standard shaped, carbon filament? bayonet light bulb. Clear glass with an amber tint. .8) 230-240 V 40 W, pear shaped, wire filament bayonet light bulb. .9-10) Osram standard shaped, heavy spiral and disc electrodes, bayonet light bulb. (The disc is loose in 10) .11 a&b) Osram black glass, large standard shaped, 230-240 V 125 W, bayonet light bulb. .12) Philips tubular shaped projector lamp with instruction leaflet. .13) Philips tubular shaped projector lamp with instruction leaflet in original box. .14) EH JA 12 V 55 W small projector lamp. .15) Large special purpose, standard shaped, frosted bayonet light bulb. .16) Siemens, standard shaped, modern Edison screw light bulb. .17) Philips, standard shaped, modern Edison screw, frosted light bulb. .18) Crompton, gas filled 240 V 75 W, standard shaped, bayonet frosted light bulb in original box. .19) Crompton, gas filled 230 V 300 W. standard shaped, large modern Edison screw light bulb. .20) Probably an extension cord with a bayonet fitting at one end connected by a twisted cord of two fabric covered wires to a large socket. This socket has a copper Edison screw inner, surrounded by a ceramic tube and covered with a copper housing. The housing is cracked in two places.Some have makers brand and voltage and wattage stamped onto the glass.scientific instrument, ballarat school of mines, globes, edison, lamps, light bulbs, bayonet -
Federation University Historical Collection
Equipment - Scientific Instruments, Flash-Point Tester, 1898
Probably used in the Ballarat School of Mines Chemisry Laboratories, at that time led by Professor Alfred Mica Smith, with lecturer Daniel Walker. From W. Watson & Sons, Block Arcade, MelbourneAn early model of a flashpoint apparatus, of mainly brass construction, heated by a spirit lamp. Complete with two mercury-in-glass tfermometers (50 degree to 70 degrees celcius x 1 degree, 10 degrees to 50 degrees celcius c 1 degree), and lamp-stand. Serial Number 1786.scientific instruments, chemistry, alfred mica smith, daniel walker, ballarat school of mines, w. watson & sons ltd, thermometer -
Blacksmith's Cottage and Forge
Lamp, 1900 (estimated)
This item type was used during the First World War throughout Europe. This item is an artillery siege lamp. It was used by artillery units. The lamps were powered by a single candle, the light being magnified by a lens. A shutter closes over the lens to give an illuminated vertical line. They were used originally in fortified siege artillery posititions as a general purpose lamp. They were also used as aiming lamps when they were placed in front of artillery posititions and used as a guide in aiming at night. Further research has suggested that this item may have been attached to bicycles for illuminating the way in the blackout.This item is considered rare and important. It is historically and technically siginficant at a national level. Painted black metal(tin) candle power, hand held or placed on flat area, open base so candle can be inserted and 'screwed' in, side door for lighting, fron magnifying glass, metal lens cover with vertical slit. There is considerable damage to the black paint in the external regions of the lamp.world war one, military, candle, artillery, europe, lamp, black, artillery siege lamp, artillery units, candle power, aiming lamp, wwi, 1900, australian war memorial, bike light, bike, bicycle, bicycle lamp, blackout -
Flagstaff Hill Maritime Museum and Village
Lamp
Kerosene lamp with ceramic base and shade. Metal shade holder and glass cover for mantle.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village -
Flagstaff Hill Maritime Museum and Village
Lamp
Lantern frame with chain painted white with glass cover and lighting apparatus missing.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village -
Flagstaff Hill Maritime Museum and Village
Functional object - Lamp, Bradley & Hubbard, 1900-1919
One of the most common centre draft kerosene lamps one can find in the USA and Canada is the Rayo. Large and sturdy, simple to use, but also notorious for being a fuel hog. This lamp was made by Bradley and Hubbard Metalworks in Chicago also Bradley and Hubbard made the “Perfection” brand lamps that look like the Rayo and are pretty much the same lamp with all parts interchangeable. The Rayo was given away to customers for free as a promotional item by the Standard Oil Company. The lamp’s huge appetite for fuel meant a hefty increase in sales of kerosene for the company and increased profits. The Rayo is a classic centre draft lamp that uses a widely available tubular wick that measures 62mm flat. It employs a simple and reliable mechanism for securing wicks in the burner along with a brass tube with many small teeth at its end. The tube is attached to the toothed rack that’s moved up and down by the adjuster knob.This type of lamp was used in most households and on rural properties before the introduction of electricity and is an early example of a promotional. The lamp was given away to customers of Kerosene oil as a means of increasing the Standard Oil Company sales of Kerosene during the late19th to early 20th century.Lamp of metal without shade. Mantle burner, plated light metal base. Ornate shade holder. Broken glass.Marked "Rayo Junior"flagstaff hill, warrnambool, flagstaff hill maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, lamp, mantle lamp, metal lamp, lighting, oil lamp, bradley & hubbard -
Flagstaff Hill Maritime Museum and Village
Lamp
Lamp, grey colour metal round with red inner glass. Moveable handle & hinged lid. Outer clear glass surrounds lantern & is intact. Meteorite' Model #92277flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village -
Flagstaff Hill Maritime Museum and Village
Lamp
Starboard side light with fresnal glass lens with removable blue/green filter, oil/kero burner with reflector inside. Made by "Tung Woo Hong Kong No. S1477", rounded front and 2 flat sides, bracket on one side for hanging. H 57.5cm x D 35cm.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, lamp, starboard side light -
Bendigo Military Museum
Equipment - LAMP
Khaki painted metal casing with space for battery. Carry handle on top with on & off switch also on top. Front has globe & reflector with glass front and blackout cover which can be lowered over light. A belt clip is attached to back of lamp.Stamped on belt clip D↑ most wording unreadable ----No-------Thorne - 44lamp, army equipment -
Kiewa Valley Historical Society
Lamp Table Kerosene, pre 1950s
... This nearly fully glass made table lamp(kerosene) has... Kerosene This nearly fully glass made table lamp(kerosene) has ...This particular lamp was made for the dinner table or "parlour". This was the most effective indoor lighting before electrical lighting was introduced in the 1940's. These table lights would have still been used after this time as emergency lighting during electrical power shortages (outages). These emergency lighting lamps, including candles, were eventually replaced by battery power. The Kiewa Valley was supplied by electricity well before many other rural regions due to the State Electricity Commission constructing the Kiewa Hydro Electricity power turbines (late 1930's to mid 1950's). Petrol and diesel generators were used in other rural regions before state wide electricity was available.The significance of this kerosene lamp to the Kiewa Valley is that it provides the proof that before the Hydro electricity scheme was established in the valley, householder and commerce relied on candle/kerosene power. Although at certain times before battery and solar energy became the night time lighters the sole source of lighting was candle power and kerosene power. The supply of both however was still required by most of the population by supply from city and larger country town suppliers. This nearly fully glass made table lamp(kerosene) has a large glass bowl/basin like kerosene storage unit with a glass circular finger handle (similar to a ordinary cup). Formed single star like patterns (50mm apart) encircle the centre of the bowl. On top of the bowl sits the metal (brass) wick holder with a small wheel protruding out one side for adjusting the wick length(increasing or decreasing the strength(regulating) of the amount of light projected. Four prongs rise from the circular base light fixture holding the windproof and refractive glass "pot belly" shield. lamp table, kerosene lamp, household lighting (non electrical) -
Kiewa Valley Historical Society
Lamp Small Kerosene, circa early 1900s
... upon the size of the lamp(wick and glass bowl). The small size ...The period when kerosene was extensively used for indoor lighting was before electrical reticulation was installed in rural areas. In remote areas this was up to the mid 1900's. The kerosene lantern however was still in use, for camping and outdoor activities, well beyond this period and was eventually replaced by LPG and battery powered lighting. The transition phase to "modern" outdoor and domestic lighting lingered on the rural areas where the electrical reticulation suffered from reliable constant supply.In the Kiewa Valley, being a rural region, had reliable electrical domestic and farm supply only after the Kiewa Hydro Electricity Scheme had been fully operational. The supply was relative to how close the homestead was to the major electricity substation. This kerosene lamp was in use during the period when it was the only reliable source of domestic night time lighting. The strength of refractive light produced by this lantern/lamp hinged upon the size of the lamp(wick and glass bowl). The small size of this lamp suggests that it was for use in a small room(children's bedroom) or as providing a light for a safe walk to the outside ablutions (toilet) area. This small kerosene lamp has an enclosed "cup" body which would have contained the kerosene fuel. The top wick holder, made from brass, has an extended enclosed spout which raises the wick approximately 20mm from the bottom of the holder. The wick holder screws into the the top of the kerosene reservoir bowl and has a wick adjustment screw (light control) at one side. The small white glass light reflector bulb nestles securely onto the wick holder and is kept snug by snap designed extending "fingers". The section between the bottom of the refractive glass "light" bowl and the top of the kerosene bowl has perforations to allow air passage to feed directly to the wick.The light refracting bulb is open at the top to allow heat and smoke from the burning wick to escape upwards.On the wick control screw "CWB BRITISH MADE"kerosene reading lamp, domestic lighting, bedside light -
Kiewa Valley Historical Society
Transformer Lamp System, late 1950's
This transformer lamp system, which has a dial to transform 240 volts to a minimum of 32 volts was used by electrical technicians to inspect internal parts of the large generators (even in small confined spaces). The reason for the reduction of the 240 volts to the 32 volts was for the safety of the inspector. The SEC Victoria Hydro Scheme's electrical generators are powered by the hydro force of "stored" water at a higher altitude. The establishment of both the NSW and Victorian Hydro schemes was achieved from the mid 1900's to the 1960's. At this the point in time the need for additional power sources to quench both an industrial and domestic demand for electricity was purely an economic and not and environmental (carbon reduction) factor. This hydro scheme was instigated by "the Government of the day" as a bold move and was the major force of the World War II refugee and "technical" workforce inclusion of skilled and unskilled migration into the Australian environment. Although this mass "invasion" of workers with families was thought of in some circles as intrusive, the expansion of population post war years and its integration into the Australian rural sector, produced the multi- lingual multi-cultural diversity of later years.This transformer lamp is very significant to the Kiewa Valley as it was introduced as a very small part of the explosion of human resources into the valley. This influx of population transformed the region from that of a basically quiet rural region to one which evolved into both industrial and larger residential community. This evolution in the valley created a change, not only in the "physical" landscape but also the socio-economic expansion which permitted other "tourist" based industries into the valley. This is also a specific electronic item which was manufactured in Melbourne and not sourced from Europe or Asia. This demonstrates the fast evolution of Australian technology to a high standard compatible to that of the rest of the world.This heavy hand held electrical transformer (transforms 240 volts to 32 Volts) an has one leather handle on the top with three small (gauze filtered) air holes. It also has two 2 pin directional cable distribution (clipsal) in/out points 10amps / 240 volts. There is one glassed in volts/ac meter and one variable switch (180 to 150 voltage in settings of 10 volt increments.There are two vents (one on each of the smaller sides). There is also one three pin electrical lead coming out from the top.On one side is a manufacturer's plaque with "ELECTRONIC A & R EQUIPMENT MELBOURNE" and underneath "TYPE 1719, PRI V. 180 250" underneath "V.A. 1250" underneath "CYC 50" underneath "SEC V. 115" underneath "SEC A. 10 . 8". The label on topside "CAUTION SET SWITCH TO 250 v BEFORE CONNECTING TO MAINS THEN, WITH EQUIPMENT OPERATING, SET METER TO RED LINE.kiewa hydro electricity scheme, victorian state electricity commission, transformers -
Frankston RSL Sub Branch
Lamp, c. World War 1
Arthur E. Woodley donated the WW1 Military Carbide Signal and General Purpose Lamp to Frankston RSL. It was given to Arthur E. Woodley of Crib Point during the 1960s by Captain Ivan E. Layton MBE who was then the Executive Officer of Melbourne Legacy. During WW2 Ivan Layton was secretary to General Blamey. Ivan Layton died on 15th September, 1979. The carbide workings of the lamp were removed because of corrosion, otherwise it is almost complete.WW1 Military Carbide Signal and General Purpose Lamp which is round and made of brass. The lamp has a latched and hinged brass top. Brass and wood hinged handle with knurled access knob which is situated at the top of the lamp. In between the handle uprights is a round chimney flu which allows heat to escape. Approximately one third down from the top of the lamp there is a brass side handle. Immediately to the left of the handle is a rectangular curved view port with brass cover. Directly opposite the side handle is a convex glass window. Air vents are located at the bottom of the lamp. Inside the top half of the lamp is a chamber which contains the carbide lamp and perpendicular sleeves for the insertion of coloured glass panels. The bottom half of the lamp contains the carbide.Manufacturers Stamp, 'PLAYER & MITCHELL LTD', 'SENTINEL WORKS' 'BIRMINGHAM'ww1, military, brass, lamp, world war 1, round, great war, carbide, signal lamp, player mitchell, birmingham -
Upper Yarra Museum
Lamp accessory, Tilley Lamp Company
... Highway Yarra Junction yarra-valley-and-dandenong-ranges Lamp ...A glass jar supplied by the company Tilley,it is sealed with a lid The lid has a printed blue label. Inside the jar is a small wire appliance with a handle at one end and the other end has packed fibres on both sides of the scissor type blades. The fibres are blackened. Printed on the lid. Methylated Spirits Fuel. for pre-heating Tilley Lamp.tilley lantern vapourized fibres methylated spirits torch -
Upper Yarra Museum
Lamp
http://en.wikipedia.org/wiki/Horse-drawn_vehicle http://www.coyaltix.com/lamps.htmlThe candle light needed to be protected from the wind. This removeable light or lantern has 4 sides with 2 oblong bevelled glass panals, 3rd panel is plain with a heat vent and the 4th opens to light the lamp and has a 4.5 cm round red glass which would act as a reflector. The candle holder screws out to allow for a narrow candle to be inserted. It has a black ventilated cover on top and has slide fixture to attached the lamp on to the carriage. . Powerhouse Museum Collection Thesaurus Protected lamps or lanterns, fixed or removable, used on coaches or carriages. Commonly made of brass, they often were fitted with reflectors as well as red lenses to serve as tail lights (Art and Architecture Thesaurus).red and clear glass lenses light candle reflector bevelled glass horse buggy tail light -
Kiewa Valley Historical Society
Lamp - Bradley and Hubbard Oil Lamp
Bradley and Hubbard Co. 1869 to 1940. Pat'd 1895 - 1898.Used by a Kiewa Valley residentNickel plate body with glass chimney and large white lamp shade. Both bowl and base are panelled and the base is scrolled on the edge. The bowl has a fill cap inscribed B & H and opposite there is a ratchet wheel lift. On top of the bowl is a decorated cylinder which lifts up to enable the lamp to be lit with a match. The glass chimney sits on top. There are 3 curved equally spaced rods coming up around this cylinder - to hold up the shade.Embossed on Fill Cap lid: "B & H" Embossed on top of bowl "Dec. 1885 / No. 4 Radiant / The/ B & H" and opposite "Pat'd Aug. 16 1888" Embossed on side under the 'grate': Pat'd Feb. 16 '97" Painted on glass chimney: "Griffen - Brand / dragon logo / Fire Proof / Madein Saxony / Rochester / No. 2lamp, lantern, bradley & hubbard, kerosene, oil light -
Orbost & District Historical Society
lantern, 1939?
Blackout lantern used in WW11. This type of lantern was used during both World War. It is an artillery siege lamp and was originally used by artillery units. The lamps were powered by a single candle, the light being magnified by a lens. A shutter closes over the lens to give an illuminated vertical line. They were used originally in fortified siege artillery positions as a general purpose lamp. They were also used as aiming lamps when they were placed in front of artillery positions and used as a guide in aiming at night. These lamps were often used on the front of bicycles to guide at night. Donated by Clem Heather. Forestry Commision, carved faces on trees with axe., builder of tall. spliced single pole fire towers. This item is considered rare and important. It is historically and technically siginficant at a national level.Small black metal blackout lantern with handle. Front of lantern has round shield with small slit - small door at side for easy lighting of candle. It is hand held or placed on flat area, open base so candle can be inserted and 'screwed' in. Front is a magnifying glass and it has metal lens cover with vertical slit. lantern blackout ww11 military candle-power lamp -
Orbost & District Historical Society
lantern
This item is an important example of the early technology of artificial light. It has historical significance in demonstrating lighting devices used before the widespread use of electricity.Kerosene/oil hand-held lantern with carry handle. Red glass window (for a show of red light) and a clear glass window that opens for lighting of wick. (Dietz Dainty Tail Lamp)lantern candle dietz-dainty-tail-lamp -
Orbost & District Historical Society
lantern, circa 1890
This item is an example of a lighting device used before electricity and battery power were widespread.A small brass Elfin Reflector Night kerosene lantern with a reflector plate at the back. A handle runs around the middle. It has a small canvas wick. The glass is missing.On top of fuel tank-ELFIN REFLECTOR NIGHT LAMP On back-MADE IN U.S.A. BY EDWARD MILLER & CO USA On wicker winder (left) -E. MILLER -CO.U.S.A.lamp lantern kerosene oil lighting miller-edward -
Warrnambool and District Historical Society Inc.
Functional object - Portable lamp, Lucas Industries, c 1900
This portable lamp was manufactured by the Lucas Industries, a company in Birmingham, England that first produced lamps after 1875. It could have domestic use or be attached to cars or bicycles early in the 20th Century to provide light at night. The lighting fluid was oil. This object is an interesting example of lighting for cars and bicycles and in the home in the late 19th and early 20th Centuries.This is a brass lantern with a circular glass piece in the middle front, and a top metal mechanism with a handle. Inside the circular opening is a domed jet with holes for lighting the lamp. On the sides there are various mechanisms for turning the light up and down, opening the front glass and opening the bottom to allow filling of the lighting fluid. The item is corroded on the exterior. The top has air vents to permit the vapours to escape. On the side is the maker's name LUCAS No. 722 KING OF THE ROAD JOS. LUCAS LTD. vintage lighting, lucas industries -
Warrnambool and District Historical Society Inc.
Functional object - Portable cycle carbide lamp, Powell & Hanmer, Birmingham, c 1920
This is a removable bicycle lantern probably dating from the first half of the 20th Century. It is a carbide lamp which was a popular form of lighting, particularly in rural areas. This item has no known local provenance but is retained as it is a good example of an early bicycle lamp.This is a brass and steel bicycle lamp. It has a circular glass front, a mechanism for attaching the lamp to the bicycle, a lighting adjustable wick and two glass panels on the side, one green and one red. There is a label with the manufacturer's name on the side. POWELL & HANMER "KINGFISHER" MAKERS, BIRMINGHAMvintage lighting, powell and hanmer -
Yarrawonga and Mulwala Pioneer Museum
Kerosene Lantern X 2
Two metal lanterns with metal handles. A 7cm oval glass inserts in each of the 3 sides. A hinged door is on the fourth side. Open arched top on each. A kerosene lamp base inside.One is labelled CRB. One is labelled OCA. -
Anglesea and District Historical Society
Lantern, Estimated early 1900's
Rail signal lamp, probably used an oil burner, before electricity was used. This item is missing the glass lens and oil burner. Victorian Railways rail train brass lantern signal bull''s eye lamp.Nonerailway lantern, signalman's lamp -
Anglesea and District Historical Society
Tilley Lamp, W. H. Tilley, Estimated 1954-57
Tilley Owl England Kerosene Pressure Lantern. A camping pressure lamp with dark blue enamel top. Pump action handle pressurizes the fuel tank to approx 2 atmospheres. Owl motif on base (very unclear).TILLEY - ENGLAND (on tank) GLASS - TILLEY - DAVISIL 171 HEAT RESISTING / MADE IN ENGLAND Owl motif on basetilley, kerosene, lamp -
Robin Boyd Foundation
Functional object - Lamp, Don Brown from Brown Evans and Co. - BECO in Australia
This Beco lamp was designed by Donald Brown, a pre-eminent Australian lighting designer in the '50s and '60s. Robin Boyd often specified BECO lighting, including elsewhere in his own home. This was originally a bedside reading lamp in the upper living room, as seen in the Mark Strizic 1958 photograph in Robin Boyd's book Living in Australia p129.Beco 720 lamp, with black stand base with switch and white glass shadeBrown Evans & Cowalsh st furnishings, robin boyd, ohm2022, ohm2022_25 -
Friends of Westgarthtown
Lamp, paraffin
Paraffin lamp. Dark wooden turned ornate stem. Metal base. Vitreous enamel fuel reservoir. Glass chimney with mantel. Plastic and cloth shade."Aladdin 21C Made in England GB. PAT. NOS. 694273-4 21C11" imprinted on fuel reservoir. "Aladdin heat resistant glass" imprinted on chimney. " Remove this gallery when lighting REG. TM. Aladdin Made in England" Written on gallery (under chimney)lighting, kerosene & oil, aladdin, kitchen lamp, light, paraffin, mantel, table lamp, chimney, lamp shade.