This hand operated drill was used to drill holes in the rails so that with fishplates (metal joiners) the rails could be bolted together to form a continuous length.Historic - Railways Permanent Way and Works - track equipment - Hand Operated Rail Drill Hand Operated Rail Drill made of cast Metalpuffing billy, hand operated rail drill

Hand Rail Drill Out on the track in the old days, it was sometimes required to drill some holes in a piece of rail so that two rails may be joined together by a metal joiner – called a fishplate. Before the use of generators and oxy cutting, the only way to do this was with a hand drill. This is the machine operated by two people, that would drill a hole in the rail. With two to three holes to be drilled in each rail end (ie 4 or 6 holes), it was a tiring, back breaking job. And then there was usually the rail on the other side of the track to be done! Historic - Railways Permanent Way and Works - track equipment - Hand Rail DrillHand Rail Drill made of metal puffing billy, hand rail drill

Hand Operated Rail Saw Out on the track in the old days, it was sometimes required to cut a piece of railway track. Before the use of generators and oxy cutting, the only way to do this was with a hand saw. This is the machine operated by two people, that would cut a piece of rail in half. And when the rail was cut, it was usually required to join it to another rail which required putting in 4 to 6 holes in the rail with a Hand Operated drill. Historic - Railways Permanent Way and Works - track equipment - Hand Operated Rail Saw Hand Operated Rail Saw made of cast metalpuffing billy, hand operated rail saw

Light Rail Bender Most rails are produced straight. While they to easily bend and appear flexible, they are required to bend for some curves, at rail joins on curves and at point (turn-out) junctions. For a safe transition around curves and in the finer areas of the point, this use to be done with a manual rail bender. Sometimes referred to as a Buddah, the rail bender attaches its two claws to the rail. In the middle of the two claws is a screw that is slowly tightened using a crow-bar to bend the rail. Tightening the screw too fast or too tightly may not give the structure of the rail time to redistribute and the rail may break if not done properly. Historic - Railways Permanent Way and Works - track equipment - Light Rail Bender Light Rail Bender made out of cast wrought ironpuffing billy, light rail bender

Railway tracks are produced straight. They may appear to be easy to bend and may appear flexible, but are required to be bent for curves, at rail joins on curves and at point (turn-out) junctions. For a safe transition around curves and in the finer areas of the point, this was required to be done with a manual rail bender. Sometimes referred to as a Jim Crow, the rail bender attaches its two claws to the rail. In the middle of the two claws is a screw that is slowly tightened using a crow-bar to bend the rail. Tightening the screw too fast or too tightly may not give the structure of the rail time to redistribute and the rail may break if not done properly.Victorian Railways Permanent Way and Works track equipment Light Rail Bender narrow GaugeCast iron semi-circular tool, with hooked ends and central screw shaft.puffing billy, rail bender, jim crow

Rail Turning Bar Rail is heavy, sometimes as much as 120 lbs per yard. To assist in being able to move rail, a special turning bar was developed. Usually a long handle, on one end various features in the head allow rail to be moved Historic - Railway Permanent Way and Works - track equipment - Rail Turning BarRail Turning Bar made from cast wrought iron puffing billy, rail turning bar

Red Trolley - BN Class Trolly Class: BN* * Trailers marked (*) are classified as Rail Mounted Tools or Tool Carriers for the purposes of Section 1 of Appendix 1 of the General Instructions. Number: 1, 2 & 3 Name: - Description: Flat top dummy Load Capacity. - Goods : 1 ton (1 tonne) - Persons. ---Puffing Billy Railway - Narrow Gauge Track maintenance Vehicle - BN Class TrollyRed Trolley - BN Class Trolly - Flat top dummy made of wood and wrought ironpuffing billy railway, pbr, red - trolley, bn class trolley, trolley, trolly

Yellow Trolly - BN Class Trolly Class: BN* * Trailers marked (*) are classified as Rail Mounted Tools or Tool Carriers for the purposes of Section 1 of Appendix 1 of the General Instructions. Number: 1, 2 & 3 Name: - Description: Flat top dummy Load Capacity. - Goods : 1 ton (1 tonne) - Persons. ---Puffing Billy Railway - Narrow Gauge Track maintenance Vehicle - BN Class TrollyYellow Trolly - BN Class Trolly - Flat top dummy made of wood and wrought ironpuffing billy railway, pbr, rolling stock , yellow - trolley, bn class trolley, trolly, trolley

NVW 1 - Track Patrol vehicle Rebuilt by Puffing Billy Volunteers given Number NVW 1 as it was built with a (VW) Volks wagon engine Was originally a trolley on the Australian Portland Cement Ltd at Fyansford Victoria Obtained by the Puffing Billy Preservation Society around 1968. Originally 3'6" ( 1067mm) before being rebuilt. Historic - Puffing Billy Track patrol - Rail Vehicle - NVW 1 NVW 1 - Track Patrol vehicle made of metal & steel with canvas vinyl blindsNVW 1puffing billy, nvw 1, trolley, trolly

V.R Fuel Can for Trolley - Victorian Railways Fuel Can for Trolly Motor Spirit Highly Inflammable Transporting Tin Container "Motor Spirit" is just another name for petrol. "K" and the "KS" Kasey Trolleys were two stroke petrol motors Operation, Care and Maintenance of Track Motors Victorian Railways, 1959 http://www.geoffsrailpix.com/Documents/Motors.pdf gives the following : Inspection motor type B, - straight petrol Inspection motor type V, - pre-mixed petrol Motorised tricycle type M.T., - pre-mixed petrol Gang motor type K.S., - pre-mixed petrol Gang motor type K - pre-mixed petrol Motor cars altered for rail uses (Wiki) Petrol Inspection Car This was a small car numbered '1' and named the Inspection Car. It was built in England in 1923, but was not found in the 1936 stocktake. Gang Motor The eight-horsepower Gang Motor held five people, and was built at Arden Street in late 1923. In 1950 the vehicle was removed from the rolling stock register and given to "Way and Works" as a track motor. Motor Car The Motor Car was put into service in mid 1925, after being fitted with rail wheels in lieu of tyres. In 1927 the car was named "Mr Molomby's Inspection Car", and allocated to Seymour. It was scrapped in 1952. Dodge Cars There were seven Dodge cars in rail service. The cars were numbered 1 to 6, with car 7 listed "No 7 Repair". The cars were built by the Dodge Company of Melbourne and assembled at Newport. Construction was in 1925 and they lasted until 1949.Historic - Victorian Railways - Permanent Way and Works - track equipment - V.R Fuel Can for TrolleyV.R Fuel Can for Trolly - Metal Fuel TinMotor Spirit Highly Flammable V.R 8 ?puffing billy, victorian railways, fuel can, trolley, trolly

Rail spike from the Wensleydale rail line. The line ran from Moriac to Wensleydale which closed in 1948 and was dismanatled in 1951. The rail spike is a large nail with offset head used to secure rails and base plates to railroad ties in the track.Nonerailway spike, wensleydale railway, crampon

One man lost his life during the building of this bridge. The bridge was constructed by the Victorian Railways between 1927 to 1929 to carry a new double track goods line. This enabled trains from all parts of the state except Gippsland to have direct access to the Tottenham marshalling and sorting yards. These yards were constructed in the 1920's to relieve congestion in the Melbourne Yard near Spencer Street station. The congestion was being caused by the construction of suburban passenger platforms associated with the electrification of the suburban railway network. Initially the bridge was for goods trains but during the Second World War it was also used by troop trains. When the standard gauge line was built in 1962 all trains to Albury and Sydney have used this route, thus avoiding travelling through Essendon and Pascoe Vale on the suburban tracks. The standard gauge track across the bridge took the place of one of the broad gauge tracks so broad gauge trains crossing the bridge in either direction have to now use the same track. The bridge is 1,257 feet (383.13 metres) long and 180 feet (54.86 metres) above the water level. It is just 63 feet (19.2 metres) short of a quarter mile in length between abutments. There is a similar bridge on the same railway line crossing the Moonee Ponds Creek between Gowenbrae and Glenroy, however it is smaller at 1060 feet (323.08 metres) length and 115 feet (35.05) height.The bridge is now Victorian Heritage Registered under Number: H1197, and Heritage Overlay Numbers HO5, and HO107. On the Heritage Register it is named RAIL BRIDGE (ALBION VIADUCT). According to the Heritage Report the bridge is scientifically and architecturally important because of its large size, and because of the cost effective design features such as two girders per span (one for each track), the K bracing in the towers, and the broad flange beams as columns. When it was being built it was the largest trestle bridge in Australia, and until the Sydney Harbour bridge was constructed it was the highest railway bridge.Five B&W yellowing photos showing stages of construction of the Maribyrnong River Viaduct known as the Trestle Bridge but mainly known locally as the QUARTER MILE BRIDGE. It is a railway only bridge which runs over the Maribyrnong River between Sunshine North and Keilor East. A sixth image, which is not part of this set of photos, is included to show what the completed bridge looks like.

Section of Narrow Gauge Railway Track. Two standard spaced section joining holes at one end of the Rail

2 photos of three story flour mill and adjoining buildings 1920's.Two photographs of railway tracks in front of the Stawell flour mill and adjoin buildings. Two people are standing in front of the three story flour mill with a timber fence along the railway tracks and a telephone pole in front of two of the four rail wagons. stawell industry

Photo depicts Cordillo Downs Shearing Shed, located 176kms north of Innaminka. Donated by Gwen Cox (Hon. Staff Member). Once the largest sheep station in the world, the shearing shed had 120 stands. The wool clip had to be carted 600km down the track to the rail head at Farina by camel train. In 1883, a complete scouring plant was installed at "Cordillo". The region now (1989) carries cattle.shearing sheds, photographs, cordillo downs

One of a collection of photographs taken of the Nunawading Railway Station prior to the lowering of the railway line and building of the new railway station on the western side of Springvale Road so that the Springvale Road Rail Crossing can be eliminated.Black & white photograph of he precinct surrounding the Nunawading Station and the Springvale Road Railway crossing. This photograph is of the railway track looking east from railway crossing in Springvale road. Note the railway station in the distance. See NP 3545 to NP3567 for the complete set of photographsnunawading railway station, springvale road nunawading, redevelopment of railway line/springvale road.

One of a collection of photographs taken of the Nunawading Railway Station prior to the lowering of the railway line and building of the new railway station on the western side of Springvale Road so that the Springvale Road Rail Crossing can be eliminated.Black & white photograph of he precinct surrounding the Nunawading Station and the Springvale Road Railway crossing. This photograph is the railway crossing and tracks looking west to Blackburn. See NP 3545 to NP3567 for the complete set of photographsnunawading railway station, springvale road nunawading, redevelopment of railway line/springvale road.

One of a collection of photographs taken of the Nunawading Railway Station prior to the lowering of the railway line and building of the new railway station on the western side of Springvale Road so that the Springvale Road Rail Crossing can be eliminated.Black & white photograph of he precinct surrounding the Nunawading Station and the Springvale Road Railway crossing. This photograph is the station looking from the entrance of station on the north side of the tracks. See NP 3545 to NP3567 for the complete set of photographsnunawading railway station, springvale road nunawading, redevelopment of railway line/springvale road.

The train smash occurred in Sunbury between the Station Street level rail crossing and Sunbury Station on February 6th 1952 at around 10pm. The goods train was being pulled by the green locomotive, which was used to take the Jubilee train throughout Victoria in 1951, to acknowledge 125 of European settlement in Victoria, ran into the back of another stationary goods train on the rail line. The guard, A.C Read, in the stationary goods train was killed. P J Mcwhirter, the guard in the other train was injured. The tree lined street in the background is Horne Street.This smash was one of a number that have happened along the Sunbury rail line and in the vicinity of Sunbury Station over the years.A black and white photograph with a white border of a train smash which wrecked a steam engine and carriages. Workmen are on the tracks surveying the wreckage. A rail crossing is in the background.jubilee train, train crashes, station street, sunbury railway station, a c read, p j mcwhirter

On 17th April 1919 a stock train travelling north crashed head-on with a goods train coming in the opposite direction. The driver thought he had been given the all-clear to proceed into Sunbury and it was only when the train was approaching the Macedon Street bridge that he saw the red light and it was too late. The accident caused damage to rolling stack and disruption on the Bendigo and Maryborough lines. The train coming from Bendigo smashed onto the platform at Sunbury. The driver of the stock train was thrown under the van and suffered a broken arm and facial injuries. The fireman was thrown clear of the tracks. A local Sunbury doctor treated them before they were taken by a casualty train to hospital. A crew from Melbourne came to Sunbury to repair the damage. The track was cleared by that afternoon.This rail crash is one of a number that have happened in and near Sunbury over the years.A black and white photograph with a cream border, of a goods train smash at a railway siding. The carriages have 'jack-knifed'. Four men are on the tracks looking at the damage while a number of onlookers are surveying the damage from a footbridge. There are boxes of rabbit carcasses in crates stacked in the foreground.rail crashes, sunbury

17th April 1919 a stock train travelling north crashed head-on with a goods train coming in the opposite direction. The driver thought he had been given the all-clear to proceed into Sunbury and it was only when the train was approaching the Macedon Street bridge that he saw the red light and it was too late. The accident caused damage to rolling stack and disruption on the Bendigo and Maryborough lines. The train coming from Bendigo smashed onto the platform at Sunbury. The driver of the stock train was thrown under the van and suffered a broken arm and facial injuries. The fireman was thrown clear of the tracks. A local Sunbury doctor treated them before they were taken by a casualty train to hospital. A crew from Melbourne came to Sunbury to repair the damage. The track was cleared by that afternoon. This photograph shows the crane lifting steam engine off the platform at Sunbury Station. This rail crash was one of many that has occurred in and near Sunbury and further on the tracks on the Bendigo Line over the years. A black and white photograph with a cream border of a steam train engine on its side with a crane lifting it back onto the rails. Two workmen are standing by the tracks.train crashes, sunbury station

2x metal spikes used to secure plates on railway tracks to sleepers

Black and white negative - 4 scanned images - of the laying of the first track inside the BTPS depot - placing sleepers and rail on No. 3 road. May or June 1972,trams, tramways, btps, trackwork, depot

Newspaper clipping from The Courier, 13/9/2018, titled "Getting our old tram tracks back on new tracks", about the deteriorating tram track in Wendouree Parade and the Museum seeking "Pick My Project" funding. Quotes Neville Britton, Operations Manager. Article written by Rochelle Kirkham, Photo Kate Healy. Gives details of the funding link. Has a photo of Neville pointing to a rail with tram 28 in the background. See Reg Item 7122 re the project outcome and 7123 for the award itself.btm, track repairs, wendouree parade, pick my project

The two items concern the work being undertaken at the time by the City of Ballarat to reconstruct Bridge St Mall. The City of Ballarat notes the archaeological significance of the works. The photograph shows some of the rail being excavated. Understood that the work is being done in four stages.Demonstrates the work to return road traffic to Bridge St BallaratReport downloaded from the City of Ballarat website - 21-11-2023 and digital image from [email protected] received by email 21-11-2023bridge st, bridge mall, city of ballarat, roadworks

These screws were samples provided to BTM by Ajax Fasteners. Two Rail Screws (each slightly different) in cardboard box. These screws were samples provided by Ajax Fasteners. Box has self adhesive labels showing name, delivery address and description of contents.ballarat, tramways, track

Yields information about depot activities of the BTPS in building the depot fan and access track.Set of 10 Agfa blue and white plastic mounts - 27mm square slides or 35mm slides of BTPS workers, c1973/1974 preparing rail joints or welding them. .1 - welding access track .2 - setting up to weld track .3 - welding access track .4 - installing fish plates prior to the extension of 2 road across the level crossing - Noel Gipps .5 - Cutting Rail - Noel Gipps and Barry McCandlish .6 - Cutting Rail - Noel Gipps, Barry McCandlish and Bill Kingsley .7 - welding track across the curve in Wendouree Parade .8 - ditto with Richard Gilbert and Noel Forster .9 - welding track across the curve .10 - dittoVarious notations by John as to the slide number and the trams in pencil and ink.tramways, trams, btps, depot, trackwork, wendouree parade

Yields information about depot activities of the BTPS in building the depot fan and access track.Set of 4 AGFA blue and white plastic mount 27mm sq and Fuji film 35mm slides of views of the depot from across the parklands c1973 - 1974. .1 - looking north with the rail stack in the park. .2 - ditto with 26 on the fan - note overhead is up. .3 - from the east side of the fish hatchery - overhead is up .4 - from the east side, with rails, earth stacks and pipes - no overhead up - early 1973 - 26 and 27 are on the fan .5 - ditto - some tidying up - power is on - 26 on the fan.Various notations by John as to the slide number and the trams in pencil and ink.tramways, trams, btps, depot, overhead, track construction, tram 26, tram 27

Yields information about the BTPS constructing No. 1 road at the depot.Digital images scanned from 35mm slides of the construction of 1 road points, first half of 1973. Points and crossings installed and poles installed. Little segments of rail have been laid out to indicate the position of the track.trams, tramways, btps, trackwork, depot, overhead

Yields information about the extent of the Ballarat and Bendigo tramway systems and possibly has a strong association with the work of Tom Murray.Set of two hand drawn maps of the Ballarat and Bendigo tram systems, showing loops, terminus, depots and rail lines, including out of use loops and reserved track. Possibly made during the 1960's or early 1970's. Drawn on lined foolscap paper - have been torn from a pad.trams, tramways, map, drawings, ballarat, bendigo