Yields information about the installation of the service pits in the depot during 1935/1936 and the methods usedSet of 2 Black and white photo prints from collected negatives of the construction of service pits and the pit for the wheel grinder at the SEC Ballarat depot building, during refurbishment by the SEC during the 1935/ 1936. 1352.1 - Formwork being set up for the service pit in No. 1 road at the SEC depot. 1352.2 - finished concrete walls for pit and wheel grinder on No. 4 road at the SEC depot, but not yet fully backfilled. No. 12 at the front of the depot and two other single truckers on adjacent tracks. 2nd copy held of 1352.2 ex moveable display boards. Colour photocopies laminated of these photographs on display 6/2000 at 02-02-06. 3rd copy of 1352.2 added 14-08-2006. See Reg Item 3806 for a photograph of the grinder in use. Copy 4 - of both photos - large format prints (203H x 253W) - added 28/7/2007, ex Alan Bradley holding of prints, received 5/2007. See also Reg Item 3901 for a mounted set of these photographs along with those of Reg Item. 1351, Neg rescanned 14/5/2020 at 3200dpi, images replaced. tramways, trams, wendouree parade, sec depot, rehabilitation, service pits, wheel grinder, tram 12

A rim splitter was used on the outer rims of older vehicles to facilitate removal and replacement of tires. The tool was used to remove a tyre and replace it onto a split wheel rim. After the air was let out, the safety rim key was pulled. The swing arms were spread out and the three arms evenly spaced around the rim. The single arm with the screw gear needed to be close to the split so that the hooks fit on the rim and the rim was then pulled inward and the tyre could be be removed from the rim. After the tire was repaired or a new one was ready to be put on the collapsed rim the tool was used to push the rim back together and the safety key could be reinserted. A rim splitter were a universal type tool used for many cars of the 1920's and 1930's.A cast iron rim splitter which has two hinged side arms with hooked ends. The middle shaft has a hooked end and an inner bolt that can be screwed up or down.St Joseph Michigan Hercules Product Co Made in U.S.A. L 7motoring rim-splitter tyres tool

18NBH - Excursion Car (28) Puffing Billy Service History or Notes Between 1979 and 1988 the Puffing Billy railway built six more NBHs, numbered 18-23. These had steel frames, padded seats, and a wide "window sill". At first glance they look the same as the previous NBHs. There are other minor construction differences due to the use of steel framing. 18NBH entered traffic on 19/4/1997; Currently these six steel framed NBHs (numbers 18-23) are being modified to provide double doors and space for wheel chairs at one end. The photo on the right shows the exterior of one such NBH. These have a seating capacity of 24 passengers.Historic - Puffing Billy Railway Narrow Gauge - Passenger Rolling Stock: Excursion Car18 NBH Passenger Carriage - Excursion Car18NBHpuffing billy railway, pbr, rolling stock , 18 nbh, narrow gauge - passenger rolling stock, passenger carriage - excursion car

19NBH - Excursion Car Puffing Billy Service History or Notes Between 1997 and 1998 the Puffing Billy railway built six more NBHs, numbered 18-23. These had steel frames, padded seats, and a wide "window sill". At first glance they look the same as the previous NBHs. There are other minor construction differences due to the use of steel framing. 19NBH entered traffic on 5/12/1997 Currently these six steel framed NBHs (numbers 18-23) are being modified to provide double doors and space for wheel chairs at one end. The photo on the right shows the exterior of one such NBH. These have a seating capacity of 24 passengers.Historic - Puffing Billy Railway Narrow Gauge - Passenger Rolling Stock: Excursion Car19 NBH - Passenger Carriage - Excursion Car made of wrought iron and timber19NBHpuffing billy, pbr, rolling stock, 19 nbh, narrow gauge - passenger rolling stock, passenger carriage - excursion car

20NBH - Excursion Car Puffing Billy Service History or Notes Between 1979 and 1988 the Puffing Billy railway built six more NBHs, numbered 18-23. These had steel frames, padded seats, and a wide "window sill". At first glance they look the same as the previous NBHs. There are other minor construction differences due to the use of steel framing. 20NBH entered traffic on 19/12/1997 Currently these six steel framed NBHs (numbers 18-23) are being modified to provide double doors and space for wheel chairs at one end. The photo on the right shows the exterior of one such NBH. These have a seating capacity of 24 passengers.Historic - Puffing Billy Railway Narrow Gauge - Passenger Rolling Stock: Excursion Car20 NBH - Passenger Carriage - Excursion Car Steel Iron and timber20NBHnbh, puffing billy, narrow gauge

23NBH - Excursion Car Puffing Billy Service History or Notes Between 1979 and 1988 the Puffing Billy railway built six more NBHs, numbered 18-23. These had steel frames, padded seats, and a wide "window sill". At first glance they look the same as the previous NBHs. There are other minor construction differences due to the use of steel framing. 23NBH entered traffic in 1998. Currently these six steel framed NBHs (numbers 18-23) are being modified to provide double doors and space for wheel chairs at one end. The photo on the right shows the exterior of one such NBH. These have a seating capacity of 24 passengers.Historic - Puffing Billy Railway Narrow Gauge - Passenger Rolling Stock: Excursion Car23 NBH - Passenger Carriage - Excursion Car 23NBHpuffing billy, pbr, rolling stock , 23 nbh, narrow gauge - passenger rolling stock, passenger carriage - excursion car

The photograph of the Royal District Nursing Service (RDNS) Holden Torana vehicles was taken in the RDNS Headquarters car park at the rear of 452 St Kilda Road. These cars are part of the RDNS fleet, with others housed at RDNS Centres. The cars were used by the RDNS District nurses to visit patients in their own homes. This photograph depicts two door Holden Torana cars of 1972.Royal District Nursing Service (RDNS) has had various modes of transport over the last 130 plus years. At first, from 1885 as Melbourne District Nursing Society (MDNS), their Trained nurses (Nurses) walked the streets and lane ways amid the slums of central Melbourne. As the Society expanded public transport was used, and bicycles were bought by the Society in 1903 and used in inner areas until 1945. During the Spanish flu epidemic, in 1919, MDNS appealed for assistance to procure Motor vehicles so the Nurses could visit an influx of cases. Through trusts, grants and donations four 'Ford T Model' cars were procured which enabled the Nurses to triple their visits. Through constant use the cars were in such a poor state two were sold in 1922 and the others later. In 1922-23 three Peugeot cars were purchased and a woman Chauffeur, 'Miss Sword', was employed who lived in the Home and was also in charge of the garage. MDNS was expanding and a Motor Auxiliary was formed in 1929 to take the Trained nurses (Sisters) to patients, and some Sisters used their own cars; even a motorcycle was used by one Sister in 1933. All these forms of transport were intermingled and in the early 1950s, and now as Melbourne District Nursing Service, seven Ford Prefect cars were bought followed by twelve Ford Anglia cars 1955. Having received Royal patronage; the now Royal District Nursing Service (RDNS) had its own fleet of Holden vehicles by the mid 1960s and the Motor Auxiliary ceased operating in 1971 as by then all staff employed were required to have a driving licence. Seat-belts had been introduced to Victoria in 1959 and District fitted them to their cars from 1962, even though they did not become compulsory until 1970. The Holden vehicles were replaced with grey Holden Torana vehicles. After several years the fleet was changed to white Toyota Corolla vehicles. The Melways Directory of maps was introduced in 1966, which was a boon to the Sisters, though it was a few years before it went beyond Seville, so a large paper map was used by the Sisters visiting patients in the areas passed Seville. By 2009 there were 598 cars in the fleet and the Sisters travelled 9 million 200,000 kilometres – this is equivalent to 12 trips to the moon and back. Black and white photograph of 14, some partly hidden, new grey Holden Torana two door vehicles parked in two rows in the RDNS concrete based car park. The cars are parked with their front lights, grill, bumper bars and number plates facing the left of the photograph. The cars are seen side-on with the full side-on view of the two cars at the beginning of the rows seen in the foreground of the photograph. The flat bonnet is the same width as the rest of the body of the car; the windscreen slopes upward and joins the flat roof; there are two wiper blades resting at the base of the windscreen. In line, and at the level of the windscreen, a quarter window, and two windows divided by a narrow pillar can be seen running along the side of the car above the slightly convex body work and front door. The rear window slopes back from the roof and the slope continues on the upper bodywork of the boot lid. A metal strip runs along the side of the car about half way down the bodywork, and another runs just up from the beginning of the front wheel arch to the rear wheel arch; beside the front wheel arch is the word 'Torana'. The round, with capital letters 'RDNS', insignia can be seen on the upper centre of the front door of the two cars. The solid wheel caps have the Holden logo on them. The front grill which runs between the headlights on either side of the car, slopes slightly backwards from the central Holden badge. The bumper bar below this is metal. Black number plates with white written capital letters and numbers 'LFA - 208' and 'LFA - 207' are seen on two of the cars in the front row. The tops of two front seats with headrests and the top of a long back seat can be seen inside the car. A tall brick fence is seen running along the rear and right hand side of the car park. In the left background is a two storey building with a flat roof, and behind this on its left is a part of a tall building and to its right part of a bare tree can be seen. To the buildings right rear part of a house can be seen. In front and to the right of this is a three storey brick building, with the top two storeys seen above the car park fence. Multiple windows run along both levels of this building which has a tiled hip roof. The tops of some bushes are seen behind parts of the car park fence.Barry Sutton Photographer's Stamp Quote KX83rdns, royal district nursing service, rdns transport, rdns headquarters, rdns car park

Visible behind T-94 is an AEC Railmotor (with tiger stripes on front) and trailer used on branch lines to haul a 4-wheel trailer. Steam locomotive T-94 has been preserved and is currently on display at the Australian Railway Historical Society Museum at North Williamstown http://www.australiansteam.com/T%2094.htm "V.R. Cavalcade" Centenary 1854-1954 Exhibition (11-25 Sep 1954) presented a model railway occupying about 1,400 square feet in the Lower Town Hall featuring a number of model railway working scale models. The exhibition also included a display of rolling stock, track, electrical and other railway equipment held at Spencer Street Railway Station.Digital TIFF file Scan of Kopdak 620 black and white negative transparencygeorge coop collection, display, spencer street railway station, v.r. cavalcade, victorian railways centenary 1854-1954 exhibition, aec railmotor, railmotor, t-94, t-class steam locomotive

Double or exposure containing an AEC Railmotor (with tiger stripes on front) and 4-wheel trailer used on branch lines. Where the strips appear to curve down is a sun visor over the windscreen of the railmotor. The image is double exposed with a E-class 2-4-2 steam locomotive and Tait train on display adjacent "V.R. Cavalcade" Centenary 1854-1954 Exhibition (11-25 Sep 1954) presented a model railway occupying about 1,400 square feet in the Lower Town Hall featuring a number of model railway working scale models. The exhibition also included a display of rolling stock, track, electrical and other railway equipment held at Spencer Street Railway Station.Digital TIFF file Scan of Kopdak 620 black and white negative transparencygeorge coop collection, display, spencer street railway station, v.r. cavalcade, victorian railways centenary 1854-1954 exhibition, aec railmotor

The Birney tram was named after its designer Charles Birney and was designated a "safety car". It was a type G tram that had a smaller wheel base and was designed specifically for routes with lighter traffic as it could only carry 50 passengers. It featured folding doors and steps and was the first tram that could be operated by the driver alone without a conductor. This particular tram was built in 1925 by the J G Brill Company in Philadelphia, USA. It was flat-packed to Adelaide where it was reassembled. It operator in Adelaide until 1935 when it was sold to Geelong before again being sold to the Bendigo Tramways in 1947. It continued to operate until the tramways closure in 1972. Each winter it becomes the Bendigo yarnbomb tram. Birney tram photographed at Charing Cross, Bendigo (probably tour with Association of Engineers on Thursday March 12th 1970). B&W photograph.burnie tram, tour at charing cross, bendigo 1973

The Phoebus is a fibreglass composite sailplane that was designed by H. Nagele, R. Linder and R. Eppler in the early 1960s for competition flying. It is a derivative from the Akaflieg Stuttart Phonix which was the first sailplane to be built of fibreglass. The first Phoebus, a Standard Class design with a 15 metre wingspan, flew in 1964. The Phoebus C is the open class version of the type that was introduced in 1967. It has a 17 metre wing span, retractable wheel and tail brake parachute. Several hundred Phoebus sailplanes (all versions) were made by the manufacturer Bolkow at Ottobrun in Germany before production ended in 1970. The Museum’s Phoebus C, serial number 866, was built in 1969. It was donated to the Museum by Ian Cohn in 2008. Early fibreglass design that was manufactured in numbers. The Phoebus is a modern looking single seat glass fibre sailplane with a ‘T’ tailplane. It is finished in white with light red detailing including thin red stripe on wings and some red striping on fuselage sides from nose to underneath wings.Serial number 866 on plate affixed inside cockpit – registration VH-GSW which has been painted on the sides of the fuselage rear of the wings. A Freistaat Bayern crest has been applied to each side of the vertical stabilizer. australian gliding, glider, sailplane, bolkow, phoebus, cohn, nagele, linder, eppler

Document titled "Tramway Maintenance Minutes of Conference - April 26 and 27 1951", attended by SEC Head Office Officers, representatives from Bendigo and Geelong. Opening note on page 2 - that the discussions should be based on the SEC operating the tramways indefinitely. Topics covered - tyres and wheel centres, truck maintenance, suspension bearings, bearing metal (white metal), motor armatures, carbon brushes, air receivers, overhead equipment, tracks, car renovation - painting, gold lining, roof, floor treatment and covering, trolley wheels, purchase requisitions, spare parts, supplies, brake shoes, timber, castings, tramway drawings, patterns and a summary of action. Has a list of attendees.Yields information and demonstrates SEC Meeting minutes about discussions between the three Provincial operators about tramcars and operations.Minutes - 26 duplicated foolscap sheets pinned (was stapled poorly) in the left hand corner.trams, tramways, minutes, sec, geelong, ballarat, bendigo, tramcar equipment, maintenance, trackwork, overhead, painting, trolley wheels, brakes, motors

These badges or insignia are probably British and belong to artillery and infantry military units but no further information has been found regarding them. They were probably attached to the shoulder pad or other part of the military uniform.These items have no known local provenance but are kept for display purposes..1 A metal badge or piece of insignia with two crossed cannons and a bursting bomb and the number 158 in the centre of the bomb. .2 A metal badge or piece of insignia in the shape of a shield with two crossed cannons, a wheel and flame. There are three metal rings at the back for affixing the item to part of a uniform. .3 A metal badge or piece of insignia with two crossed rifles, a circle with the number 158 and a crown atop. .4 A metal badge or piece of insignia in the form of a shield with two crossed cannons and a bursting bomb. There are three metal rings at the back for attachment to part of a uniform. 158military insignia, history of warrnambool, badges

black and white photo mounted on same size board. Group of 30 men and boys outside double storey building with verandah with iron lace. At left man mounted on horse. At rigfht, horse and 4 wheeled vehicle. At centre 2 men, 1 each side of box with '1311' 4 pieces of smooth material piled on box ( smelted gold ? ) At far left, 2 girls, 1 bending down. On left hand window of building 'old' On RH window ' …. Mercial bank'? Above doorway at far left ' private entrance'organization, business, oriental bank, eaglehawk

Black and white photograph of Ballarat SEC No. 21 decorated for the 1968 Myers Christmas Tram. Photographed at the depot by Bob Prentice, 16/11/1968. Tram has been decorated as a "show boat" with a paddle wheel, waves and the side windows covered to resemble port holes. Destination box has been covered with the words "To Myers". Tram has a roof advertisement "Myers for Everything under the tree". Theme: Santa's Showboat. Photographed with Lake Wendouree and the toilet block in the background. See Date advised by Alan Bradley, 15/3/03On rear in blue ink "No. 21 at Ballarat Depot / Saturday 16th November 1968 / Photo - Bob Prentice for T.M.S.V. archives" and in red felt tip pen in centre of photo "Page 1"trams, tramways, myers, decorated trams, depot, christmas trams, tram 21

Set of two black and white photographs which have been coloured to show possible arrangements for covers to the side frames of a Brill 21E and Brill 22E (single truck or four wheel truck or bogie tram). 1793.1 - Showing possible arrangement for a cover for a maximum traction tram truck - cover has been outlined in red and then coloured to match the tram colour. The body has been coloured as well with green and yellow colours. 1793.2 - ditto for single truck tram No. 20. Background for the preparation of these photographs is unknown. Date unknown.trams, tramways, trucks, covers, brill trucks, tram 20

Agfachrome Professional plastic mount (blue base, white cover) reproduction slide of a black and white photograph of Geelong Nos 8, 4, 1 and another 4 wheel tramcar and a open cab motor bus photographed within the interior of Geelong depot, prior to 1924. From notes provided by David O'Neil, 12/2003, advises that bus driver is either Bill Hamaling or Charles Stafford. Gentlemen next to No. 8 could be Vic Phipps. Hawthorn Tram Museum Reg Item 3558 shows the tram on the left hand side - Geelong 2."G 1" and "1 -1" in pencil.tramways, trams, geelong, depot, motor buses, tram 8, tram 4, tram 1

Possibly has a strong association with the tram and depot maintenance staff at the time of closure of the SEC operated Ballarat system.Colour print of a group of eight depot workers standing alongside a four wheel tram with the depot building in the background. Left to Right: G. Gray, Stan Lakey, ?, N.Lorensini, ? A. Domaschenz (kneeling), B. Peart and W. Trusler. See Reg Item 6543.4 for a colour slide of this photograph. See Reg Item 1861 for staff photo and Reg Item 3236 for other staff photos. Item was placed in an envelope marked "Mr. Tony Den Ouden" - retained with photograph in storage folder. Photo printed on Kodak Paper. Photograph by Lilian Butler?in ink on rear " Tram Depot Wendouree Parade Ballarat September 1971. With my compliments Lilian Butler"trams, tramways, sec, depot, personnel

Hand written letter signed by A. Richardson, 29 Harrison Street, Bendigo - 03/02/1970. Royal Hustler Reserve No. 2 (lift) shaft. Depth 1660 feet. Memorial Hall in Pall Mall covers site. Steel poppet legs, 60 ft high (lattice-steel garden type). Winding engines built by Roberts and Sons, Bendigo. Pair of 24 in. clear cylinders, 5ft stroke, 10ft ? drums. Note 3rd wheel on poppet legs for pumping equipment to be raised or lowered. Gold yield from this shaft 9,009 ounces.person, mining, albert richardson

Three fold DL pamphlet printed on off white paper, two colour + black - titled "Your Government Bus Service Serving you better" - discussing the pros and cons of a government bus service compared to a privately operated bus service and the subsidy provided. Notes the Liberal Coalition policy is to privatise public services. Has photos of step lift, kneeling, wheel chair and ambulance bus. Printed c1982, notes the reduction in funding and staffing. No details as to who printed the document. Second copy added 17-4-2017trams, tramways, public transport, buses, privatisation

Newspaper clipping from The Melbourne Weekly, 16/8/1994 with a cover photo of SW6 866 as a City Circle Tram, containing an article titled Transformation, The Low Down on the Wheel World". Consists of 3 full colour sheets. Article written Angela Martinkus and Michelle Griffin. Looks at the issues of ticket machines, conductors, tourism, the fleet, tram art, timetables, crimes, passenger safety, W class, works, the PTC, history of tram types and ten tram facts Includes a Photo and story on Robert D'Andrea, Norm Cross, and tram in Preston Workshops.trams, tramways, melbourne, people and places, preston workshops, conductors, ticket machines, fares, ticket inspectors, advertising trams

.1 - Instruction - approx. 50 pages, A4 pages with some foolscap pages detailing the: "Wheel diameter compensator - Kit Details and installation instructions", prepared by the Metropolitan Transit Authority for Manager Preston Workshop by the Manager electrical design and communications branch - P. CussZ. Dated July 1984 for fitting to Z1 and Z2 trams. Includes an "Owners' Manual" in a plastic folder, prepared by Selectronic Components of Bayswater. .2 -set of 3 drawings showing the layout for the circuit boards prepared by Precision Engineering dated 29-8-1991, in a labelled plastic folder.trams, tramways, z class, maintenance, electrical engineering, electrical equipment, wheels, the met, tram 980

Photograph - of a K class four-wheel or single truck tram on a PMTT route 14 (STRATHALBYN ST (Kew) - VICTORIA BRIDGE) tram service, at Harp Road and High St. The reference gives the tram based at Kew Depot in 1928. The tram was originally a Prahran and Malvern Tramways Trust tram, though, by the time of this photograph, it has been re-lettered for the MMTB, which took over the PMTT in 1920. The photograph has been marked up for a submission possibly to either Council or the MMTB for a waiting room or shelter at this location. The wall of the Harp of Erin Hotel and a Victoria Bitter sign can be seen on the right-hand side. The original photo appears to have been torn. Original photo mid to late 1920's.Yields information about the K class tram of the MMTB and methods of seeking a tram stop shelter and High Street and Harp Road intersection.Kodachrome cardboard duplicate slide - Black and white reproduction photograph - K class tram 92 - at Harp Road Kew "MP17" in penciltrams, tramways, kew, harp road, route 14, k class tram, tram 92, harp of erin, victoria bitter, high st, strathalbyn st

NRT1 - Ruston & Hornsby Diesel Locomotive Built in 1951 to a gauge of 3', this Ruston diesel locomotive or rail tractor operated on the State Electricity Commission of Victoria’s Kiewa scheme. Some years later, it was regauged to 2'6" and was operated by the Melbourne & Metropolitan Board of Works. NRT1 is a Ruston & Hornsby diesel locomotive, built in England in 1951 to a gauge of 3 feet, and was initially employed by the State Electricity Commission of Victoria. It was later re-gauged to 2' 6" and ended it's working life in 1977 when it was transferred to Puffing Billy. In 1977, it was taken to the P.B.P.S. Steam Museum and stored until 1978 when it was taken to the Emerald Carriage Workshops. Later in 1983 it was returned to service as NRT1 following the V.R. classification procedure as a narrow-gauge rail tractor, but it had number plates installed and was painted Hawthorn green. It will eventually be painted the red of V.R. rail tractors with the number & class painted on in black. This type of locomotive was popular in many industrial locations, with their unique clutch-less 3 speed gearbox meaning the driver could control them whilst walking alongside, a bonus when shunting. Adjustable tie rods meant that as the axles moved on the springs, they followed the radius of the drive chains, reducing the chances of chain snatch LOCOMOTIVE DETAILS NRT class No. originally constructed : No. in service : 1 No. stored: Wheel arrangement : 0-4-0DM Roadworthy weight : 9T 3cwt. Maximum axle load : 4T 15cwt. Tractive effort (85%) : Length overall: 15' 6" Height overall: 10' Driving wheel diameter: 18" Date of manufacture: 1950 Manufacturer : Ruston Hornsby Place of manufacture: Lincoln, England Locomotive type : Diesel Mechanical Manufacturers classification : 48 DL Historic - Industrial narrow Gauge Railway - Ruston & Hornsby diesel locomotive used by State Electricity Commission of Victoria - NRT1 - Ruston & Hornsby Diesel Locomotive NRT1 - Ruston & Hornsby Diesel Locomotive made of steel NRT1 ruston & hornsby diesel locomotive, nrt1 diesel locomotive, nrt1, puffing billy

This particular lamp was made for the dinner table or "parlour". This was the most effective indoor lighting before electrical lighting was introduced in the 1940's. These table lights would have still been used after this time as emergency lighting during electrical power shortages (outages). These emergency lighting lamps, including candles, were eventually replaced by battery power. The Kiewa Valley was supplied by electricity well before many other rural regions due to the State Electricity Commission constructing the Kiewa Hydro Electricity power turbines (late 1930's to mid 1950's). Petrol and diesel generators were used in other rural regions before state wide electricity was available.The significance of this kerosene lamp to the Kiewa Valley is that it provides the proof that before the Hydro electricity scheme was established in the valley, householder and commerce relied on candle/kerosene power. Although at certain times before battery and solar energy became the night time lighters the sole source of lighting was candle power and kerosene power. The supply of both however was still required by most of the population by supply from city and larger country town suppliers. This nearly fully glass made table lamp(kerosene) has a large glass bowl/basin like kerosene storage unit with a glass circular finger handle (similar to a ordinary cup). Formed single star like patterns (50mm apart) encircle the centre of the bowl. On top of the bowl sits the metal (brass) wick holder with a small wheel protruding out one side for adjusting the wick length(increasing or decreasing the strength(regulating) of the amount of light projected. Four prongs rise from the circular base light fixture holding the windproof and refractive glass "pot belly" shield. lamp table, kerosene lamp, household lighting (non electrical)

Black and white photograph. Forest Creek (Victoria) gold reefs crushing works. The Garfield overshot waterwheel which drove the battery at Chewton. Inscriptions on back: 'MNG 31''Garfield Mine, Chewton, J Ebbett, Manager' ( in top LHC), 'Royal Historical Society of Victoria, Bendigo Branch' (in circular rubber stamp). History of object: Previous ACC. No. 'MNG 31', Ralph Birrell 5.11.1999 'Garfield Waterwheel and Crushing Mill, Chewton:' Gardield overshot waterwheel which drove the Forest Creek Gold Mines crushing battery at Chewton. The foundations of this wheel can still be seen today.Bendigo Advertiserbuildings, commercial, garfield waterwheel at chewton

Yields information about Ballarat 's No. 39, when it was numbered MMTB 42 and the internal arrangements within the depot.Digital image from the Wal Jack Ballarat Album of Ballarat 39, when still with its MMTB number - 42 inside the depot 17-8-1951. Has a number of wheel sets in the foreground. See rear of photos for other details. See image i2 for rear of photograph. See image i3 for hi res scan of print. See image i4 for hi res scan of negative See image i5 for another view of the tram in the depot on the 125 negative. See Reg Item 6415i for a photo of the tram in Coburg Depot prior to delivery.On rear in ink "SEC Ballarat ex M&MTB 42 "C" class now No. 39 (in service Dec. 1951). Wendouree depot, Ballarat". In top right hand corner is Wal Jack stamp with no negative number written in.trams, tramways, depot, bogie trams, mmtb, tram 39, tram mmtb 42

Letter concerning "Mr Jerusalem Smith" forwarding drawings of rail Sections that could be used in horse tramways. The cross-section of the rail in the drawings have been water coloured with a blue and yellow wash. .1 - Covering Letter from Ian Armstrong of the Armstrong Collection .2 - Image of the cover of the book at Post-it note that came with the item .3 - Drawing of Gjedsted Rail. .4 - Central Webbed Rail .5 - Davies Foot Rail with fishplates shown. .6 - Davies Foot Rail with a wheel shown in the drawing. See also Reg item 4248 for further correspondence on this matter.trams, tramways, trackwork, horse trams, city of ballarat