Climax geared locomotive No. 1694 in active service on special occasions - stored at Emerald Station A Miraculous Survivor Climax locomotive No.1694 is a miraculous survivor of a rare breed of steam locomotive. For about 100 years from the mid-1850s sawn timber was carted from Victorian sawmills to the nearest railway station by timber tramway. These tramways were generally very rough, steeply graded, sharply curved, and of narrow gauge. Many had wooden rails, and horses provided haulage. The better ones used steam locomotives. In all about fifty steam locomotives are known to have worked on Victorian timber tramways. These locomotives were usually somewhat peculiar - made to cope with arduous, rough conditions, rather than speed. Climax locomotive No.1694 is the only one of these locomotives to survive intact. It was built in 1928 by the Climax Manufacturing Company, Corry, Pennsylvania, USA, for the Forests Commission of Victoria. The distinctive feature of the Climax locomotive is that the cylinders do not directly connect to the driving wheels. Instead they drive a cross shaft near the centre of the locomotive. From there the drive is transmitted to the small driving wheels through rotating shafts, universal joints, and bevel gears. The driving wheels are mounted in two four-wheel bogies so that they can easily follow sharp curves in the track. None of these features are found in normal steam locomotives. The result is a locomotive that is extremely powerful for its size, and that will cope with sharp curves and steep grades with ease. But this is at the cost of speed, Climax locomotive No.1694 is just about flat-out at 13 km/h (8 mph). Climax Locomotive Built in 1928 for the Forests Commission of Victoria and painted all-over black with the name CLIMAX painted on the sides of the cab in white block letters, this locomotive was issued to the Tyers Valley tramway which branched off the Moe to Walhalla line at Collins Siding. This locomotive was withdrawn from service in 1949 following the closure of the tramway and in 1950 it travelled from Tyers Junction to Collins Siding to Erica where it remained stored until 1965. Loaned to the Puffing Billy Preservation Society for its Steam Museum, it was taken to Menzies Creek in 1965 where it remained until 1982 when the Emerald Tourist Railway Board bought it and transferred it to Belgrave for restoration. It was returned to service for special use on the Belgrave to Gembrook line in 1988 painted in its original all-over black livery, except that the word “Climax” on the sides of the cab was now painted in the style of the Climax Manufacturing Co., a style that this locomotive had never carried.Historical - Industrial railway - Forests Commission of Victoria, Timber Logging Climax Locomotive Climax geared Steam locomotive made of steel and wrought iron Climax 1694climax locomotive works, climax, geared steam locomotive, puffing billy, climax locomotive no. 1694, steam locomotive

Station Sign - Yea Yea Station Opened 16 November 1883 Closed 8 November 1978 Yea is a former railway station in Yea, Victoria, Australia. The tracks have been removed and the reserve has been turned into The Yea Railway Park consisting of the historic railway station and eleven acres of parkland. It has a picnic shelter, barbecue, toilets, playground, skatepark, walking track, community reserve and includes Rotary Park. The station building houses Blackthorn Textiles (a privately run craft shop). Also on the site are the former goods sheds which are available for hire for varied functions. The Yea Country Market is held in the park on the first Saturday of each month and local artists hold an exhibition and sale in the goods sheds each Easter. The site is listed on the Victorian Heritage Register ref: https://en.wikipedia.org/wiki/Yea_railway_station photo at http://vhd.heritagecouncil.vic.gov.au/vhd-images/places/000/078/092.jpg Historic - Victorian Railways Station sign used at Yea StationStation Sign - Yea Metal rectangle Station Name Sign with white enamel back ground and black lettersYeapuffing billy, station sign, yea station

Station Sign - Tecoma Tecoma railway station is located on the Belgrave line in Victoria, Australia. It serves the eastern Melbourne suburb of Tecoma opening on 1st December 1924. The station was originally on the Upper Ferntree Gully - Gembrook narrow gauge line. It along with the rest of the line closed on 30 April 1954, reopening on 19 February 1962 when the line as far as Belgrave was converted to broad gauge. ref: https://en.wikipedia.org/wiki/Tecoma_railway_stationHistoric - Victorian Railways Station sign used at Tecoma StationStation Sign - Tecoma wooden rectangle Station name sign pained yellow background with black letters Tecomapuffing billy, station sign, tecoma station, narrow gauge, puffing billy museum

Station Sign - Emerald Emerald Station is situated on the Puffing Billy Railway in Victoria, Australia. It was opened with the Railway on 18 December 1900 and comprised a platform track and a loop siding. A passing loop was added between the two a few years later. There was also a spur siding off the Down end of No. 3 Road. Two standard 12 ft by 20 ft timber portable station buildings with a Van Goods Shed between (all adjoining) were provided on the platform and a Goods Shed on the No. 3 Road loop siding. Other buildings included Tea Rooms, lamp room and toilets along with a cattle race and loading bank. The station building was later reduced in length by one of the portables which housed the General and Ladies' waiting rooms. Emerald today remains very similar to the early days, but has had other Roads added into a Carriage Workshops, a turntable and storage sidings. Also, a Signal and Telegraph Branch depot in the form of a large Goods Shed and a multi-purpose yard building in the form of a Locomotive Depot administration building have been added. During 2009, the station building underwent stage one of an internal restoration to its former glory. ref: https://en.wikipedia.org/wiki/Emerald_railway_station,_Victoria photos at http://www.vicrailstations.com/Gembrook/Emerald/Emerald.html Historic - Victorian Railways Station sign used at Emerald Station Station Sign - Emerald Metal rectangle Station Name Sign with white enamel back ground and black lettersEmeraldstation sign, puffing billy, emerald station

Station Sign - Toilet Gentlemen An obvious sign for a convenience. The use of the term Gentlemen was shortened to Men at a later time. Historic - Victorian Railways Station Sign - Toilet GentlemenStation Sign - Toilet Gentlemen sign wooden rectangle Station name sign pained white background with black lettersGentlemenpuffing billy, victorian railways, station sign, toilet gentlemen sign

Station Sign - Toilet Ladies An obvious sign for a convenience. The use of the term Ladies was altered to Women at a later time.Historic - Victorian Railways Station Sign - Toilet LadiesStation Sign - Toilet Ladies sign wooden rectangle Station name sign painted white background with black lettersLadiespuffing billy, victorian railways, station sign, toilet ladies sign

In 1879, James Griffiths established one of Australia’s first tea and coffee distribution companies at 30 Flinders St, Melbourne, which is now, occupied by the boutique Lindrum Hotel. Established with his brother John, recent immigrants from England, Griffiths occupied the highest position in the commercial world during their many years as distributors of tea, coffee, cocoa and other products throughout Victoria and Australia. The Griffiths brand was a guarantee for quality of product and service as it still is today. This extensive service was provided to customers via horse drawn carts serviced by rail from Melbourne. As a spirited entrepreneur, Griffiths made his company a household name through his pioneering use of outdoor advertising by installing the infamous blue and white enamel “Griffiths Tea” promotional signs affixed to the railway boundary fences highlighting to travellers the distance to or from Melbourne, indicating so many “— miles to Griffiths Tea”. These signs, much sought after today, were well known through out the eastern states. Photographs have been published of a sign erected by a Digger in France during the First World War with the words “1100 miles to Griffiths Bros”. Tragically, James and his wife Emily with friends died in a level rail crossing accident at Bayswater in 1925. Despite this unfortunate accident, Griffiths and its culture of innovation has survived as one of the few 100% Australian owned coffee roasters, with only three owners in 128 years. http://www.griffithscoffee.com.au/about-us/back-to-1879/ Sign - Advertising - Griffiths Tea Sign - 30 MilesHistoric - Sign - Advertising - Griffiths Tea Sign - used along side of Victorian Railway lines and at StationsSign - Advertising - Griffiths Tea Sign - 30 Miles Griffiths Tea sign made of Enamel paint on metal sign30 Miles to Griffiths Tea Sign puffing billy, sign - advertising - griffiths tea sign - 30 miles

Detonator (DET) An explosive device (not shown) is placed on the rail line and triggered by wheel pressure—used to warn of hazards aheadHistoric - Victorian Railways - Detonator (DET) Boxred box - DETS 7A Made of metal sheetDETS 7Apuffing billy, detonator (det) box

Electric staff - Electric staff instruments The staff and ticket system was still too inflexible for busy lines, as it did not allow for the situation where the train intended to carry the actual token was cancelled or running very late. To provide for this, the electric train token system was developed. Each single-line section is provided with a pair of token instruments, one at the signal box at each end. A supply of identical tokens is stored in the instruments, which are connected by telegraph lines. A Staff can be removed from one instrument only if both signalmen co-operate in agreeing to the release. Once a Staff has been removed, another cannot be removed until the token which is "out" is replaced in either instrument. (There are variations on this sequence of events.) By this means, it can be ensured that at any one time, only one token is available to be issued to a driver. Staff belonging to adjacent sections have different configurations to prevent them being inserted into the wrong instrument. Nevertheless, in the Abermule train collision in 1921 and lax working procedures allowed the safeguards provided by the electric Staff system to be circumvented; a driver was handed a Staff for the wrong section, and without reading the information listed on the staff, proceeded on the mistaken belief that the Staff was correct. To prevent this, it became a requirement in the UK for the signals controlling entry to the single line section (starting or section signals) to be locked at danger unless a token has been released from the relevant Staff instrument. Historic - Victorian Railways Electric Staff Instrument Electric Staff Instrument made of Iron , Brass and Glasspuffing billy, electric staff instrument, victorian railways

Porters Luggage Trolley - large red one Used for transporting luggage and other items on a railway platforms by porters and other station staff.Historic - Victorian Railways - Station Porters platform Luggage Trolley Large Porters Trolley - made of wood and steelpuffing billy, victorian railways, porter, luggage, hand trolley

Station Porters platform Luggage Trolley - two smaller unpainted ones Historic - Victorian Railways - Station Porters platform Luggage TrolleyStation Porters platform Luggage Trolley - two smaller unpainted ones - made of wood and wrought ironstation porters platform luggage trolley, puffing billy, victorian railways

1 NBC Toilet Roll Holder Toilet roll holder that was located in 1 NBC when obtained in the 1990s Carriage 1 NBC was built 4/ 2/1899 NWS Built new at Newport Workshops Historic - Victorian Railways - Carriage Toilet Roll Holder from 1 NBC carriage1 NBC Toilet Roll Holder made of cast wrought iron puffing billy, 1 nbc toilet roll holder

These leather soled shoes were used by railway workers undertaking work on overhead electrical cables and HV boxes. Known as "slippers" they were provided just inside explosives vans and worn to stop metal protectors on shoes scraping across metal floor and possibly causing a spark and a explosion. info from Syd Coles : on Explosives Slippers Beaufort station used to get a explosive wagon with drums of gelignite regularly slipper type shoes were in a little box built into the inside wall of the wagon....A Special powdervan key was sent from H/OFFICE as a VALUE which each person handling it had to sign for it.....It would arrive on the early down Passenger Train ex Melbourne...then the "P" wagon was unloaded....Prior to the wagon leaving a Railway Internal telegram was sent to the SM @Beaufort giving the wagon number...consignee (owners of dynamite) contents and the KEY number which would be sent....When all unloaded the KEY sent back as a VALUE...a Internal telegram sent as to KEY number and train it was despatched on....fair bit of security.but couldn't afford to lose a KEY as they fitted all the LOCKS used on the EXPLOSIVE "P" wagons whatever Stations they went to.Historic - Victorian Railways - leather soled shoesLeather soled slip-on shoes, with single strap across bridge of foot and featuring stitchwork along edges.VR & arrow symbolpuffing billy, victorian railways, leather soled shoes, railway slippers, explosives, worker safety, linesmen

Guards Hand Lamp - Tri Colour Harvey, Shaw & Drake 1913 Gills Alley is located between Queen and Elizabeth streets, extending north to a dead-end from Little Collins Street. In 1895, Gills Alley extended through from Little Collins Street to Bourke Street. The Saracen's Head Hotel was located on the corner of Gills Alley and Bourke Street. By 1920, however, the north end of the lane had been closed off, leaving the sole entrance to the lane on Little Collins Street. Gills Alley was at this time the location of several warehouses, showrooms and factories belonging to the Harvey, Shaw and Drake Company.Guards Hand Lamp - Tri Colour Harvey, Shaw & Drake 1913 used by the victorian railwaysTri Colour Harvey, Shaw & Drake 1913 guards hand lamp Made of Metal , brass and glassTri Colour Harvey, Shaw & Drake 1913 puffing billy, guards hand lamp, harvey, shaw and drake company, tinsmith

fittersLeather Tool Bag - Large A leather bag used by the fitter to carry spanners and other tools required for repairs.leather bag used by fitters on the victorian railways Leather Tool Bag - Large made of leather with copper rivetspuffing billy, leather bag, victorian railways, fitter

fitters Leather Tool Bag - Medium fitters Leather Tool BagLeather Tool Bag - (Medium size)made of leather with copper rivets puffing billy, railway fitter, victorian railways, tool bag

vaporizing kerosene gas lamps of this type were used by track gangers to facilitate night works. Historic - Victorian Railways - Permanent Way and Works - track equipment - Ganger's Lamp made of metal, brass and glass V.R ( and Arrow symbol ) AL 14puffing billy, victorian railways, ganger's lamp

NKS Trolley Motor Transporting Box A wooden box used for transporting the engines of the Gangers trolleys between the line in use and the Workshops at Spotswood. Engines were often changed over due to mechanical failure or being required for a service. Rather than send the complete trolley in for work, the engine was removed and transported. These boxes may have arrived at a location with an engine in it, to replace the one returning to the Workshops, cutting down the time that the trolley may have been out of use. Historic - Victorian Railways - Permanent Way and Works - track equipment - NKS Trolly Motor Transporting BoxNKS Trolly Motor Transporting Box - two boxes made of timber with wrought iron fittings puffing billy, nks trolley motor transporting box, trolly, trolley

Kerosene was used to light the signal lamps at night time on a railway, to ensure that a locomotive driver could see that the line was clear there was no danger of another train ahead. This container was used to store the in kerosene to fuel such lamps and was kept inside a lamp room until required for use.Victorian Railways - Keroseane Container Used in the storage of kerosene prior to use in lamps at stations.Large, cylindrical tin container with conical lid and wire handle. A small zinc spout is embedded in the lower quadrant. The word 'KERO' is stencilled in white across the front. Keropuffing billy, kerosene, fuel, combustible material, tin container, lamps

Gangers Shed Desk A desk used in the Gang Shed for office work and other associated functions. Historic - Victorian Railways Permanent Way and Works - Gangers Shed Desk Gangers Shed Desk made of wood with wrought iron fittingspuffing billy, gangers shed desk, victorian railways

Railway tracks are produced straight. They may appear to be easy to bend and may appear flexible, but are required to be bent for curves, at rail joins on curves and at point (turn-out) junctions. For a safe transition around curves and in the finer areas of the point, this was required to be done with a manual rail bender. Sometimes referred to as a Jim Crow, the rail bender attaches its two claws to the rail. In the middle of the two claws is a screw that is slowly tightened using a crow-bar to bend the rail. Tightening the screw too fast or too tightly may not give the structure of the rail time to redistribute and the rail may break if not done properly.Victorian Railways Permanent Way and Works track equipment Light Rail Bender narrow GaugeCast iron semi-circular tool, with hooked ends and central screw shaft.puffing billy, rail bender, jim crow

Van 8 NUU - Louvered Van Louvred Truck (11) (on u/frame of 110 NQR) Untrafficable NUU LOUVRED TRUCK. Seven louvre vans for carrying general goods were built during 1899-1901, with another one in 1906 and a further six in 1911, a total of 14 louvre vans numbered 1-14. The term Louvred Truck describes the sides which consist of fixed louvres for ventilation. The aim was to keep the goods inside cool. VR Service History : *NUU 8.VA - 20/ 7/1906 NWS Built new - / /1926 - To NU 8.VA - NU 8.VA - / 9/1928 - Modified AC Malco 21/12/1953 - Sold (to) Coulston & Hyder RS54/338 Historic - Victorian Railways Narrow Gauge - Rolling Stock - Louvred VanWooden Louvered Van on under frame of 110 NQR - Made of Timber on a Wrought iron frame - current condition Untrafficable8NUUpuffing billy, 110 nqr, 8 nuu - louvered van, victorian railways, 2'6" gauge, narrow gauge rolling stock

1NB - (1st Series) Saloon carriage (24) Body and underframe purchased by Puffing Billy Preservation Society from Pakenham In Active Service NB There were three types:- NB Class - Number Built (1st Series) 6 - Number Built (2nd Series) 17 - Number Built (3rd Series) 4 Nos. 1-6 were Saloon cars having end platforms and a ladies toilet, and were built from 1899-1904. Nos. 7-23 were 5-compartment side loading cars, built from 1906-1915. Nos. 24-27 were the former NAB class cars mentioned previously and were also side loading, having 6 compartments and two ladies toilets. VR Service History NBB 1.VA - 4/ 2/1899 NWS Built new - circa 1910 - To NB 1.VA - *NB 1.VA - / 2/1928 - Modified AC Malco BO 21/10/1930 NWS Into Workshops - 5/12/1930 NWS Out of Workshops (46 days) 30/ 1/1951 - Scrapped Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: Saloon carriage (No. 1) Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection1NB Passenger Rolling Stock: Saloon carriage (No. 1) - Made of Timber and steel 1NBpuffing billy, 1nb, saloon carriage, victorian railways, narrow gauge passenger rolling stock, 2'6" guage

14NB - Carriage (NB 2nd series) 6 compartments (40) Awaiting restoration NB There were three types: -Nos. 1-6 were Saloon cars having end platforms and a ladies toilet, and were built from 1899-1904. Nos. 7-23 were 5-compartment side loading cars, built from 1906-1915. Nos. 24-27 were the former NAB class cars mentioned previously and were also side loading, having 6 compartments and two ladies toilets. VR Service History *NB 14.VA - 16/12/1912 NWS Built new - / 5/1926 - Modified AC Malco 15/ 7/1931 NWS Into Workshops - 20/10/1931 NWS Out of Workshops (98 days) 5/ 8/1936 NWS Into Workshops - 6/11/1936 NWS Out of Workshops (94 days) 26/ 2/1951 - Scrapped - Body and underframe purchased by the Puffing Billy Preservation Society from Pakenham.Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: NB Passenger carriage Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection Passenger Rolling Stock: Passenger carriage 14NB - Carriage (NB 2nd series) 5 compartments - Made of Timber on a Wrought iron frame Awaiting restoration14NBpuffing billy, 14nb, nb passenger carriage, 2'6" guage, victorian railways, narrow gauge passenger rolling stock

NB Class - Number Built (1st Series) 6 - Number Built (2nd Series) 17 - Number Built (3rd Series) 4 26 NAC - Former NB Class (3rd Series) - Carriage 3 compartments and van (24 pass.) In Active Service - Belgrave Station Yard NAC COMBINED NB PASSENGER CAR AND GUARD'S VAN. A compartment NB which has had a guard's compartment temporarily added in one end. Due to the temporary nature of the guard's compartment, this vehicle retains its number in the NB numbering sequence, but has been classed NAC to differentiate it from the standard NBC. The use of the A is a recognition of the car's original NAB classification. VR Service History NABAB 2.VA - 1/ 7/1907 NWS Built new - circa 1910 - To NAB 2.VA - *NAB 2.VA - circa 1910 - Reference Photo SL20 p20 20/ 8/1923 FTG To NB 26.VA - NB 26.VA - /12/1927 - Modified AC Malco BO 27/ 9/1934 NWS Into Workshops - 30/10/1934 NWS Out of Workshops (34 days) 17/12/1954 - Scrapped Body to Eng. Spcl Works, RS55/707 Purchased by the Puffing Billy Preservation Society as a body & underframe. Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: Passsenger carriage Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection Passenger Rolling Stock: 26 NAC - Passenger carriage - Made of Timber on a Wrought iron frame 3 compartments and van (No. 26)26 NAC puffing billy, 26 nac, nac passenger carriage, victorian railways, narrow gauge passenger rolling stock, 2'6" guage

10NBH Carriage - Excursion Car In Active Service - Belgrave Station Yard NBH SECOND-CLASS EXCURSION CAR. The H was recognising their use for "Holiday" traffic. 15 of these cars were built in 1919 and numbered 1-15. Two more were built in 1981, and numbered 16 & 17. Two extended versions for wheelchair passengers were built in 1981 & 1983. These were numbered 51 & 52 - a separate number series due to the different type of vehicle. Six, numbered 18-23, were built in 1997-98. These had steel frames, padded seats, and a wide "window sill". At first glance they look the same as the previous NBHs. There are other minor construction differences due to the use of steel framing. 18NBH entered traffic 19/4/1997; 19NBH on 5/12/1997; 20NBH on 19/12/1997, the others added in 1998. VR Service History : *NBH 10.VA - 8/12/1919 NWS Built new - /12/1928 - Modified AC Malco BO circa 1955 - Condemned -Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: Excursion Car Victorian Heritage Register (VHR) Number H2187 Puffing Billy Locomotives and Rolling Stock Collection10 NBH Passenger Carriage - Excursion Car made of steel and timber10NBHpuffing billy, 10nbh, nbh - excursion car, victorian railways, victorian railways narrow gauge - passenger rolling stock

Van 2NBC - 1 compartment and van (7 & 4 ton capacity) In Active Service - Belgrave Station Yard NBC COMBINED SECOND-CLASS PASSENGER CAR AND GUARD'S VAN. Six cars, numbered 1-6, were built during 1898-1905 and originally classed NBDBD. The D was previously the letter code for Brakevans/Guard's Vans, but was changed to C when the double-letter code was dropped in 1910. A final NBC numbered 7 was added to the fleet in 1910. VR Service History : NBDBD 2.VA - 3/10/1899 NCL Built new - circa 1900 - Photograph R101: as N2BDBD circa 1910 - To NBC 2.VA - *NBC 2.VA - / 5/1926 - Modified AC Malco circa 1955 - Condemned -Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: Passenger and Guard's Van carriage Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection2NBC - Combined Second-Class Passenger Car And Guard's Van. - Made of Timber on a Wrought iron frame 2NBC - 1 compartment and van (7 & 4 ton capacity)2NBCpuffing billy, 2nbc, 2nbc - combined second-class passenger car and guard's van, victorian railways, narrow gauge passenger and guard's van rolling stock, 2'6" guage

The NQRs were the standard Medium open goods wagon. Generally the sides and ends were removable thus providing a totally flat truck. Three long drop-down doors formed the sides thus allowing easy loading and unloading. 218 of these goods vehicles were built between 1898 and 1914 ? numbered 1 - 218​. Originally, these wagons carried the code letter R​ as they were built with sides and ends. They later had the R removed. Unlike the Broad Gauge, VR's 2 ft 6 in (762 mm) narrow gauge network never had four-wheeled wagons (aside from a handful of trolleys). Because of this, a single design of open wagon emerged and this was the only type of wagon ever used on these lines. This was the NQR class, a wagon with the same length and loading capacity as a Broad Gauge four-wheeled open wagon to make transferring freight between the gauges easier. The wagons, numbered 1 through 218, were built between 1898 and 1914. The wagons used the same underframe as most other non-locomotives on the VR Narrow Gauge. Letters and numbers were originally painted only on the end bulkheads and doors, both of which could be removed as traffic dictated, and this made wagon identification difficult until the decals were transferred to the underframes of each wagon In the 1910s some NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223​, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames In the 1960s the Puffing Billy Railway added grids in the floor of some to enable them to be used to drop ballast on the track where needed. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 92NQR - Goods Vehicle - Open Medium Truck NQ/NQR OPEN MEDIUM TRUCKS. 218 of these goods vehicles were built between 1898 and 1914 numbered 1-218. Originally, these wagons carried the code letter R as they were built with sides and ends. Some later had the R removed if they regularly ran as flat wagons without theh sides and ends. Over the years, a number of NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames. 92 NQR VR Service History : *NQR 92.VA - 2/ 3/1907 NWS Built new - / /1926 - To NQ 92.VA -Historic - Victorian Railways - Narrow Gauge Rolling Stock - NQR Open Medium Truck with drop ends Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection 92NQR - Open Medium Truck with drop ends made of Steel and metal92NQR puffing billy railway, pbr, rolling stock , 29 nqr, narrow gauge rolling stock, victorian railways, nqr wagon

149NQ - Water Wagon - Water Truck (2000 gallons) In Traffic NQ WATER TRUCK. This vehicle (No. 149) is an NQR without sides and with a 2000-gallon (9000-litre) water tank fitted. Over the years of V.R, operation a number of NQs were fitted with water tanks, but retained their NQ code and number. (For a number of years this vehicle carried the classification NWT but retained its number in the NQ numbering sequence). VR Service History : *NQR 149.VA - 24/ 9/1910 NWS Built new - / /1926 - To NQ 149.VA -Historic - Victorian Railways - Narrow Gauge Rolling Stock - Water truck (No. 149) Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection 149 NQ - Water Wagon - Water Truck (2000 gallons) made of Steel and metal149 NQpuffing billy, victorian railways, narrow gauge rolling stock, nq water wagon, 149 nq

10 NU Louvre Van - Louvred Truck (11) Untrafficable NUU LOUVRED TRUCK. Seven louvre vans for carrying general goods were built during 1899-1901, with another one in 1906 and a further six in 1911, a total of 14 louvre vans numbered 1-14. The term Louvred Truck describes the sides which consist of fixed louvres for ventilation. The aim was to keep the goods inside cool. VR Service History : *NUU 10.VA - 30/12/1911 NWS Built new - / /1926 - To NU 10.VA - NU 10.VA - / 5/1926 - Modified AC Malco /12/1972 BEL To NW 10.VA Sec72/3400, RS72/9371 NW 10.VA - 26/ 8/1976 CLS Photograph #662.2-.4: and end detail 1/10/1977 - Off Register To ETRB Sec76/3630 RS77/4223 Build Date: 30/12/1911 NWS Built new Victorian Heritage Register (VHR) Number H2187 NW 10 is a 1972 reclassification of NU 10. It is presumed the van was used to store tools and equipment. In 1977, the van was removed from railway records and control handed to the Puffing Billy group.Historic - Victorian Railways Narrow Gauge - Rolling Stock - Louvered Van Victorian Heritage Register (VHR) Number H2187 Puffing Billy Locomotives and Rolling Stock CollectionWooden Louvered Van - Made of Timber on a Wrought iron frame - current condition Untrafficable10 NU puffing billy, louvered van, 10nu, victorian railways, 2'6" gauge, narrow gauge rolling stock