Taken between 1928 and 1930, depicted is the Bethanga Bridge under construction. The Bridge was completed in 1930 and was built to assist residents of the Bethanga district to travel to Albury. Other bridges would become submerged by the backed-up water of the Murray and Mitta Rivers so the Bethanga bridge was built two miles above the Mitta Weir. The Bethanga Bridge was built north of the future Hume Dam which would be completed in 1936. At 2430 feet long, Bethanga Bridge was the longest road bridge in Australia at the time of its completion. The Bridge is 20 feet wide and made up of nine 270 feet long spans. Materials used include ten tons of paint for the steel works; 1600 tons of steel; 900 tons of timber for the decking; and reinforced concrete for the piers. The tender for the construction was awarded to C. Ruwolt Pty. Ltd., engineers who were located on Victoria Street, West Richmond. The contract was awarded for £71,890. It was predicted between 250 and 300 men would find employment on the project. The news was well received by trade unions at the time as there had been a drop in available engineering work.This photograph is historically significant as it depicts the progress of the Bethanga Bridge construction, which was important infrastructure for the area. It is also a good example of methods used in the area to assist in travel over the river prior to the construction of the Hume Dam.Black and white rectangular photo printed on matte photographic paper.Reverse: 1997 3186 / 84-19-3 / This is the bridge. / It is not yet open to traffic / yet. will not be completed / until May next / It is a wonderful bridge the / pillars are 100 feet high. / KODAK PRINT Envelope Obverse: Peterson PHOTO / Hume Weir Envelope Reverse: BMM 84-20-1,2+3. bethanga bridge, lake hume, hume dam, hume weir, murray river, bridge, bethanga, albury

View looking across Main Road to Wingrove Cottage (c.1950s), former home Charles Symons Wingrove. Charles Wingrove was a prominent figure in Victorian local government, as secretary to the Eltham District Road Board and Shire Council from 1858 to 1904, and, as Shire Engineer and Secretary to the Heidelberg Road Board. He was part of the Committee to establish the Church of England at Eltham. The Wingroves were an important pioneer family of Eltham and Wingrove Cottage is one of the most important heritage buildings in Eltham as one of the few surviving 19th century buildings. Reputedly built in 1858, Wingrove Cottage was recorded in the 1859-60 Eltham Road District rates book as a brick house owned and occupied by Wingrove with a Net Annual Value (NAV) of ₤30. In 1861, the year the Church opened, Wingrove's house was identified as a two -roomed brick cottage. Charles Wingrove is buried with other members of his family in the cemetery at St Katherine’s Church, St. Helena. This image is believed to have been incorporated in a presentation by Russell Yeoman to the 10 November 2004 Society meeting on "Significant Trees, Wildflowers and Local Gardens."This photo forms part of a collection of photographs gathered by the Shire of Eltham for their centenary project book,"Pioneers and Painters: 100 years of the Shire of Eltham" by Alan Marshall (1971). The collection of over 500 images is held in partnership between Eltham District Historical Society and Yarra Plenty Regional Library (Eltham Library) and is now formally known as the 'The Shire of Eltham Pioneers Photograph Collection.' It is significant in being the first community sourced collection representing the places and people of the Shire's first one hundred years.Digital image 4 x 5 inch B&W Negshire of eltham pioneers photograph collection, eltham, main road, wingrove cottage, george w. bell collection, significant tree

This hollow core bit has hard cutting inserts for drilling into rock. It was used to drill and recover 50mm diameter (most common size) rock cores. The rock cores were assessed by geologists and engineers to provide information for design of structures such as tunnels, dams and underground power stations (eg. McKay Creek Power Station, West Kiewa Power Station). This type of bit was also used where damage to the surrounding rock had to be minimised. The Diamond Drill Bit,used in the early 1900's, when it was primarily used as a method of sampling rock for ore deposits and oil exploration resulting in a "coring" of rock. The use of "coring" to obtained samples for the SEC Kiewa Hydro Electricity Scheme(1920's onward) was to analyse the core to obtain temperature and rainfall patterns shown by the levels of layered solidified soil(rock). This diamond drill would have been used in the early 1900's to provide a sub strata map of temperature and water patterns (over an long period of time). This was a pre requisite to any decisions about the viability of the region to provide the water needed for a successful hydro electricity scheme.This diamond drill for core sampling was at the forefront of the analysis whether to construct a hydro electrical facility in the Kiewa Valley and the adjoining alpine region. The rock core samples produced were assessed by geologists and structural engineers. It was only after extensive core drilling covering the region that solid scientific evidence could be provided to start the "SEC Vic Hydro Electricity Scheme" within its current boundaries.This "diamond" drill bit has eight "teeth" at its cutting edge. The drill creates an 55mm hole in extremely hard rock material to obtain 50mm core samples.. Three quarters down the shank it has thread screw channels to attach the bit to the drill pipe. The coring pipe attaches via screwing it onto this bit. Core samples are the main objective of this tool.alternate energy supplies, alpine feasibility studies temperature, rainfall, sec, kiewa hydro electric scheme, electricity

WT George & Co of Sherlock Street Birmingham were makers of ships lanterns under the trade name “Meteorite”. In 1941 Thomas George writer assumes a relative of WT George was granted a patent number GB546575 relating to improvements to his lamps. After this date a plate was affixed with this number. What's confusing with the companies records is that they show that in Birmingham three companies are listed making lamps together and the writer is assuming under a partnership agreement. First in 1983 W T George & Co with William Harvie & Co went into liquidation with G Bocock & Co, together, then in 1992 George Bocock and Harvie Ltd were in liquidation. Although these companies seem to have different addresses in Birmingham they were linked together given they were all liquidated at the same time for two of them. They all appear to have been partners in some way making marine lamps under the William Harvie banner. William Harvie & Co. Ltd advertised as being electric light and power engineers, and patent ship lamp manufacturers, as early as 1901-1902, as listed in the Post Office annual Glasgow Directory 1901-1902.An item made by a company that was an innovator of significant improvements in the manufacture of marine signal and navigation lamps during the late 19th and 20th centuries. Lamps made by this manufacturer are now sought after collector's items that are of significant value. Lamp, round ship's copper lamp with clear glass, handle at top, fitted with hinged and catch section at top to service lamp. Bracket at back for hanging lamp. Stamped "Meteorite 110560" Bottom stamped "Patent no GB546575 and others pending".warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, lamp, round ship's lamp, kerosene marine lamp, w t george & co, william harvie & co, george bocock & co

Metal money boxes shaped like common familiar objects became popular in the 18th century. In the 20th century, they were used to promote and advertise events and businesses. In the 1950s metal money boxes shaped like a bank building were given away to children by their parents' bank to encourage them to save money. This metal money box was produced for the company of OXO Ltd of London. It was made specifically as a souvenir of the Coronation of King George VI of England, which happened on May 12, 1937. OXO Ltd. still makes OXO stock cubes, which contain a concentrated meat extract. The cubes are used to flavour soups, gravy, casseroles and other food recipes to enhance their flavour. The cubes are removed from their foil wrapper then crumbled into the dish and mixed with the ingredients. Chemist Justus von Liebig worked with engineer George Gilbert of Uruguay to produce Liebig’s Extract of Meat, the forerunner of OXO . In the late 1890s, OXO produced a liquid form of the meat extract and in 1899 registered the OXO trademark worldwide, and in 1900 in the UK. In 1910 the OXO 'penny' cube was in production and proved very popular. The money box is significant for its connection to British Monarch, King George IV, who reigned from 1932-1952. It is also significant for its connection to the OXO cube, a very well knon brand of food additive from the mid-19th century to current times.Souvenir money box, oval cylinder with domed, pull-off lid and framed coin slot, with seams on each side. It once contained six OXO Cubes. The red tin with gold tin has the Royal Insignia of King George VI and Elizabeth on one side and the Royal medallion-style portrait of King George VI and Elizabeth on the other side. There is an inscription on the base and floral decorations on the sides. It was produced for OXO Ltd, Thames House, London, England, to commemorate the coronation of King George V1 and Elizabeth on May 12th 1937.Logo, Royal Insignia: "[Crown] over "G VI R" Medallion-style Portrait image: "GEORGE VI AND ELIZABETH MAY 12TH 1937" around " (Image of King George VI and Elizabeth) " Printed on base: "CORONATION / SOUVENIR MONEY BOX / CONTAINING / 6 OXO CUBES / BRAND / OXO LTD., THAMES HOUSE, / LONDON, ENGLAND."flagstaff hill, flagstaff hill maritime museum and village, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, money box, money safe, commemorative money box, coronation king george iv, 1937, vintage money box, oxo cube, numismatics

The ship’s communication system that was used from the late 19th century to early-to-mid-20th-century is called an Engine Order Telegraph (E.O.T.) or ship’s telegraph. The system has two parts, the Bridge Section and the Engine Room Section. The Bridge Section is usually mounted on top of a pedestal, and the Engine Room Section is often attached to a vertical surface. The standard commands printed or stamped onto the dial are the directions of AHEAD and ASTERN, and the speeds of STOP, SLOW, HALF, and FULL. The ship’s pilot on the Bridge of a vessel sends his Orders for speed and direction to the to the Engine Room with the E.O.T. He moves the lever or levers, depending on the number of engines the ship has, to change the indicator on the Bridge Section’s dial to point in the new direction and speed of travel. This change causes the Orders to be duplicated on the Engine Room Section’s dial and a bell to signal the change at the same time. The engineer then adjusts the ship’s engines and steering equipment to follow the pilot’s Order. The manufacturer, A. Robinson & Co. Ltd of Liverpool, established his business in 1780 and continued until 1968 when the business was purchased by marine products maker Chadburns, established in London in 1870.This Engine Room section is part of a ship's telegraph communication system and represents marine technology used in the late-19th to mid-20th-century. Engine Room Section of a ship’s telegraph or Engine Order Telegraph (E.O.T.). The round brass dial has inscriptions stamped around its edge and centre. Red inlaid glass plates have inscriptions in white paint on them. The inscriptions are nautical terms for direction and speed and include the maker’s details. A rotating pointer is joined to the centre of the dial. The maker is A. Robinson & Co. Ltd of Liverpool. Stamped: “FULL / HALF / SLOW / STOP / FULL / HALF / SLOW / STOP”, “AHEAD / ASTERN” Printed: “FULL / HALF / SLOW / STOP / FULL / HALF / SLOW / STOP” Stamped on the dial: “A. ROBINSON & CO. LTD / MANUFACTURERS / LIVERPOOL”flagstaff hill, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, marine technology, marine communications, engine order telegraph, e.o.t., ship’s telegraph, bridge section, engine room section, ship’s engine telegraph section, marine telegraph, a. robinson & co. ltd, liverpool

Basil George Watson was an aviation pioneer born in Bendigo 12/10/1893. The family moved to Melbourne when he was a child. In 1914 he went to England to work as an engineer for the Sopwith Aviation Company. He also took flying lessons and received his licence in 1915. He now worked as a test pilot for Sopwith but when a crash rendered him unfit for military duty, he returned to Australia in late 1915. He designed and constructed his own biplane in the back yard of his Elsternwick home. At the end of 1916 he tested his plane by flying from Point Cook to Bendigo and then to Melbourne. This included an aviation display in Bendigo. He followed this by flying to Warnambool 25/1/1916. He then set up an experimental airmail flight from Melbourne to Mount Gambier. On 28th March 1917, Watson was demonstrating aerobatics for the entertainment of AIF servicemen at Point Cook, when his plane collapsed and fell into the ocean close to shore. Unfortunately, Watson was tangled in the plane's wires and died. On hearing of his death, the bells of St Pauls in Bendigo and the Bendigo fire bell tolled.A paper detailing the life of Bendigo pilot Basil Watson, one of the first Australian pilots. 4 pages.aviation, basil watson, sopwith

At the top of the shield is a Lions International symbol consisting of two lions heads facing outwards either side of the words 'Lions International' and the letter 'L' in between them. At the base of the shield is a blue and gold coloured badge, consisting of two rifles crossed in front of the RVIB lighthouse, with the words 'Royal Victorian Institute for the Blind Rifle Club' around the outside. Between the two symbols is engraved "In memory of the late George Glover Past President-Lions Club of Bennettswood - Patron and Life Member of the R.V.I.B. Rifle Club. George developed and donated equipment in order that the blind may enjoy rifle shooting and compete with others. His work done will continue to serve." In the 1960's, the RVIB approached engineer George Glover to produce equipment to allow blind people to shoot, based upon that made available at St Dunstan's Hospital in the UK. The rifle range opened in February 1966 at the rear of St Kilda Road with 30 members, and soon became involved in matches with sighted rifle clubs in the area. Passionate about the sport, Mr Glover continued work and supporting the club until his death in 1977.1 wooden shield with engraved silver plategeorge glover, rvib rifle club

The colour negative appears to be an official photo arranged by the City of Ringwood Council.Gerald Smart was mayor in 1973/74 and 1976/77 for the City of Ringwood. He also served as a Councillor from 1967/68 until 1981/82. Married Sandra, who also served as Mayoress for Cr Pat Palmer. Gerald was instrumental in getting the Wyrenna-based local radio station, ECB-FM, off the ground. Other information:- SMART, Gerald Richard George 1967-73, Mayor 1973-74, Chartered Engineer. Melbourne University, R.M.I.T., Diploma of Radio Engineering. Son of Walter and Doris Smart. Married with one son. Cricket, tennis, golf, spearfishing, chess, table tennis, photography (8mm, 35mm, stills, music.) Theatre - Melbourne University, Emerald Hill Repertory Company. Radio - Music session on 3XY. Television - 'Consider Your Verdict', character parts. President Ringwood Arts and Crafts Society Honorary Secretary of Television Society of Australia Patron, Ringwood Swimming and Life Saving Club President Ringwood District Scouting Association Executive Committee Member of Municipal Association of Victoria Formed ECB-FM +Additional Keywords: Refer to the "Mayor" envelope, registration no. 3932, for further information.

Document. Two page advertising flyer for the Comic Opera Company, Masonic Hall, Bendigo. On the back page, ''Printed at the Bendigo Independant Office, Williamson St., Bendigo''. Advertisers: W.Parkinson and Co - Copper Plate Cleaners and gold refiners. Walter E.Ellis - Tobacconist. W.Bartle - Jeweller and Watchmaker. Mrs Newman's - Coffee Palace. Jas. Burston - Watchmaker, Jeweller and Optician. Lazarus Telegraph Hotel. H.Lorenz - Tailor. Mrs A. Keast - Dining Rooms. P. Drescher - Watchmaker and Jeweller. W A Parker - Hairdresser and Tobacconist. O'Hagan's Sandhurst Hotel. Leslie's Blacksmith. Mrs Leonard - Tobacconist. J Dunne - Market Hotel. Bright's - Fish and Fruit. E J Delaney - Harp and Shamrock Hotel. Banfield and Co - Goldbrokers. Swift and Rothberg - Tailors and Drapery. Hans Irvine - Wine Sales. T Sayer - Undertaker. Terminus Hotel. Jack Francis Cafe. A Frigerio - Wire Worker. Barnett's Jewellers. B Sluyterman - Electrical Engineer. T R Jones - Chemist. Jack E Coates - Scenery for Hire. Krast and Co - Gold Brokers. Sydney P Ewing - Dentist. H Nickson - Furniture Hire. Geo Jackman - S P Bookmaker.performing arts, elocution, theatre flyer

Yields information about the operation of one man trams in Ballarat and Bendigo and the provision of information to the American tramway or Street car press. Has a strong association with the Author - Mr Pringle.Series of five digital images of items from the Electric Street Railway Journal about one-man tram operations and wages in Ballarat, written by the ESCo Manager, Mr P J Pringle, Chief Engineer and General Manager. Images i1 and i2 - pages 172 and 173 - letter titled "Improved one-man Operation in Australia", Vol 47 No. 4, 22/1/1916 - describing the operation, and how it operates. Reference to the use in other places in made by the author and the magazine. image i3 - general comment making possible reference to a UK magazine - and how one man tram are worked and their routes, including tickets and wages. From Vol 46, page 23, 4/12/1915. image i4 - "The Principals of Differential Wages in Awards" - Vol 56, No. 19., 6/11/1920 page 965, looking at wages based on locations, arbitration, over WW1, including cost of living and renting. image i5 - "One Man cars in Australia" - Vol 55, No. 24, 12/6/2020 - page 1206, looking at the accident rates between one and two man cars.trams, tramways, one man trams, electric street railway journal, ballarat, bendigo, esco, wages, fares, accidents

Photocopy of an article in the State Electricity Commission of Victoria Magazine, Contact, Vol 1, No. 4, Feb 1937 titled "Electricity Supply and Tramways / Reconditioning the Tramway Systems at Ballarat and Bendigo". Each item had a thin strip of paper attached by staple to the top left hand corner, giving the Vol. No. details. The item gives the background to the takeover from ESCo. Details some of the work undertaken in both Ballarat and Bendigo, including the widening of double track in McCrae St to 10' to allow ex MMTB trams to run. Work at Grenville St - City Loop, the method of track laying in Ballarat - concrete stringers, welded joints, financial arrangements for the work - employment council. Includes replacement of trolley wire. Features photos of reconditioned track on the Eaglehawk Route and a caterpillar tractor. Record revised 31/3/2019 to replace images with those from Andrew Cook CD and to include item .1 .1 - Item also was originally printed with different photographs in the Electrical Engineer and merchandiser Sept 15 1936. See Reg Item 2968i5.pdf. Copy provided on heat sensitive paper.trams, tramways, sec, reconstruction, trackwork, mccrae st, grenville st, esco

Notebook - comprising heavy card covers, with preprinted (18) sheets for use as a wages sheets. Use by Wal Jack to record notes of people, events and negatives and photographs. The sheets have been side stapled and then were bound within the heavy brown cardboard sheets with a blue cloth binding on the left hand side. Book was made by 'F. W. Wright Print Ballarat" Has notes from Murray Hood of the Chief Civil Engineers Office WAGR about events and happenings in Perth, WA. Diagrams of stations on the Benalla to Yarrawonga rail line - dated 14/10/1954. Photos received dated 1953 - 1954 - steam. Photos sent to Norm De Pomeroy and received back Photos sent or received from John Radcliffe Wal Larsen - SAR Photos Notes on Wal Larsen's UK, Europe to India trip - 1963 - daily mileage and towns visited - likely to link to albums of photographs. List of Alwyn Marshall photos - Nov. - Dec 1960 - Asia, India Wal Larson photos - 1961 - QR, VR, CR etc - 1957 as well. All hand written notestrams, tramways, europe, uk, notebooks, diary

brighton, council, mayor, councillors, officers, brighton town hall, t. vincent, park ranger, j.n. clark, overseer, f. blackham, press, r.j. lawrence, bank manager, a. vogt, assistant, j. clementson, inspector, l.w.p baker, assistant town clerk, g.w. woodward, hallkeeper, g. marsh, curator, a.f. magill c.e., city engineer, w. turner, cr. w.e. briggs, dr w.c. mcclelland, health officer, cr c.h.j. pickett, c.h. livesey, rate collector, cr j.a. grant, cr. j.w. satchwell, cr p.a. oakley, j. ritson, librarian, cr c.a. hack, cr j. richards, cr h.e. hall, cr t. wilson, j.h. taylor, town clerk, cr. w.p. francis, cr j.b. grout j.p., cr h.e. pullman, g.h. jefferson, solicitor, miss d.m. grout, typist, d. thomas, office boy, peace and city year

Report - 32 pages centre stapled, printed on foolscap paper, has an index (see image i2), report of the Royal Commissioner Sawyer titled "Report on the Status and Affairs of the State Electricity Commission of Victoria and the scope and working of the State Electricity Commission Acts". Looks at the financial situation of the Commission, its management, equipment, power supply systems, Newport, technical issues, hydro power stations, Yallourn, problems with brown coal, use of Richmond Power station Signed by author on rear page. Note: At the time of cataloguing very little found on Mr. W. Sawyer - see reference in Trove for meeting with Sir John Monash - http://trove.nla.gov.au/newspaper/article/3737172/446386 and International Electrical Engineers - http://ieeexplore.ieee.org/stamp/stamp.jsp?arnumber=5217646, that he died 1/3/1966, age 93 - had been associated with Electric Street Railway companies, the Railway Engineering Department of General Electric and the firm Ford Bacon and Davis in New York City. For scan of full document see htd2104i3.pdf - downloaded from the Parliamentary web site - 29/7/2018.In the top right hand sector "J.P.S. just to let you know that I have appreciated your many courtesies and kindnesses HHS - 28/5/26". On rear page, has been signed by Willits H. Sawyer.trams, tramways, secv, power supply, royal commission, newport power station, richmond power station

File containing correspondence between the MMTB Chief Engineer Mr. Strickland and various companies, including Railless Ltd, Australian General Electric, English Electric / Dick Kerr and its UK consultants Heap and Digby between the period August 1922 and January 1923. Includes drawings, technical specifications and a book titled "AEC Railless Trolley Bus Specification", date stamped 15/8/1922. For a scan of this document see htd535-trolleybus.pdf (imaging not working correctly for this database as at 9-8-14) For a listing of the contents of this file and of Reg Item 535, see Related Documents - htd535-536list.pdf Item 535 - Trolley Buses Listed from top of file, in order found. Letters generally to/from MMTB Chief Engineer. Date Type, contents and notes 18/11/1922 Letter to Metro Vickers from Chief Engineer re Railless trams 12/1/1923 Letter to Aust GE re railless trams Not likely to proceed at this time. 11/1/1923 Letter from Aust GE Co. providing photographs, drawings, BTH, pamphlets, and general information. Includes photo of Tee-side trolley bus No. 17. No other papers with this item. 6/9/1922 Letter to Aust. GE asked for particulars and drawings of motor omnibuses These three items pinned together. 5/9/1922 Letter to Chief Engineer from Aust. GE provided up to date figures on BTH Railless vehicles. These three items pinned together. 31/8/1922 Letter to Aust GE returning folded of data in relation to petrol and petrol electric cars. These three items pinned together. 24/10/1922 Letter to Heap & Digby, thanks for information, but unlikely to use trolley buses due to poor road conditions where they could be used in terms of revenue. 14/9/1922 Letter from Heap & Digby, inclosing photos of Railless Ltd vehicles supplied to Bloemfontein South Africa and testing. These two items clipped together with drawing No. SK 14-8, showing Mexborough gradients. 28/8/1922 Letter from AEC to Heap & Digby re trolley buses, construction costs and practicality of shipping these to Aust. Includes the Mexborough test results. These two items clipped together with drawing No. SK 14-8, showing Mexborough gradients. 3/8/1922 to 31/10/22 Correspondence between MMTB and H&D regarding the Bloemfontein vehicles. Pinned together. 17/11/1922 Letter from Metro Vickers to MMTB providing details (no photos or drawings) of trolley buses – four pages. 18/1/1923 Letter to H&D thanking him for information and a paper ready by a Mr. Munro. 31/8/1922 Letter to Metro Vic – Melbourne asking whether Westinghouse had developed standard lines of motors for railless cars. 4/10/1922 Letter to Aust GE thanking for info. 2/10/1922 Letter from Aust GE providing two cuttings about railless vehicles in Birmingham and the cost of tram track construction. Papers Contained within a green strip of cloth. 26/9/1922 Letter from H&D providing info from EE – Dick Kerr Preston works equipment used by Railless Ltd. EE Specification for DK 26B Trackless trolley motors 18/9/1922 Letter from EE to H&D providing info on 20HP motors, 40HP, and other information. Blueprint – drawing 2810 – DK 26 Motor Performance curves for above motor Blueprint – No. 1312D – controller diagram Pamphlet – EE – tramcar Type D automatic circuit Breakers. Publication No. 230, dated 9/1920. Ditto, Form A, drawings No 3565, 1/1/19. Performance curves – blueprint – Type DK85A Blueprint – 4449 – outline of controller DK, Type D, form B. Blueprint – P2002M034 – DK85 Motor. EE specification for Traction Motor DK85 Modified from a tram motor. EE blueprint P2102F021, traction control wiring for form D controller. EE blueprint P2103F033 – outline of controller type SE1, form C and D. EE blueprint P2102Z011 – wiring diagram for type SE1 form controller. Performance curves for DK85A motor. EE blueprint – P2102F025 – diagram of connections (wiring) for Type SE1, form D controller. Blueprint – EE drawing – P2002M036 – DK85 motor with ball bearings. Single documents. Date Type Notes 27/9/1922 Letter to H&D acknowledging AEC Trackless trolley bus specification. 15/8/1922 Letter from H&D forwarding above specification String bound book – AEC Railless Trolley Bus Specification – stamped 15/8/22 Scanned as a separate document. 4/9/1922 Letter from Metro Vic. Melbourne advising that they have no information on Westinghouse Motors for use in railless cars, but seeking same.trams, tramways, trolley buses, melbourne, mmtb, aec, heap and digby, english electric, railless, dick kerr, general electric

Murray Comrie Collection. Shire of Bet Bet Proclaimed Sept 20, 1864 Re-defined Feb 10, 1891 Tarnagulla Borough united Oct 1915 Dunolly Borough united Nov 1, 1921 Re subdivision from 5 to 3 ridings Oct 1952Monochrome photograph of a group of men assembled in rows for a photograph. Accompanied by a handwritten note (catalogued separately as a Research Note) with subjects' names. Names of subjects from accompanying note (handwriting difficult to decipher) are believed to be: Left to Right Back/3rd row: Cr J. Grogan, A. Whitehead, G. Barman, J.B. Reid, I.R. Stevens (?), KAG Lowe (Shire Sec), Mr A Rescott (Maryborough Advertiser) Middle row: Crs N.K. Conera (Pres. Elect), D.E. Wood, A. Brownbill, J.P. Mason, D. Clark, K.R. Culleton (Shire Engineer). Front/1st row: Crs G. Fotheringham, J. Fremantle (1951-52), A. Green, J. Hickey. Note also states: 'Secretary Lowe passed away Sept 7, 1952' and 'Fotheringham House, Glenferrie' (location where photograph taken?)tarnagulla, council, bet bet shire, local government, councillors, mayor, shire, engineer, maryborough advertiser, reid, grogan, whitehead, barman, stevens, lowe, rescott, conera, wood, brownbill, mason, clark, culleton, fotheringham, fremantle, green, hickey

This photograph shows the Richardson family having a picnic on the verandah of Captain McNeil' house at Marlo - April 1897. Snowy River Shipping Company formed in 1880. They were soon shipping produce (mainly vegetables) from the area to Melbourne. The Snowy River Shipping Company was formed by Mr Henry James during the 1880s, with Captain McNeil as master. Captain Hegarty was the shipping agent at Marlo. Towing a line of small barges these paddle steamers plied their trade between the port of Marlo, and the farms along the river banks, churning their way almost twenty miles upstream to a landing beside what is now Frank Richardson’s property. On these trips, the barges carried mail and supplies to the townspeople and farmers, loading their produce, mostly maize, on the return trip to the coast. The coming of the railway in 1915 spelt the end for the little river boats. ( ref. F. W. RODWELL in the “Snowy Review”) Frank Richardson 1877-1950 was a sawmiller at Tabbara and helped build and run paddle steamer "Curlip"as engineer. Captain McNeil was an always cheerful Marlo identity and local children had many times sailing with him on the river. Captain McNeil with tug went out through the entrance and brought in the schooners.This item is associated with the Richardson family, early settlers of the Orbost district.A black / white photograph of a group of people having afternoon tea on the end of a verandah of a wooden house. All are seated.on back - " The Richardson family picnic at Marlo"richardson-family-orbost-marlo mcneil-captain

Samuel Baird attended Ballarat College 1864 - 1872. He was the first student enrolled at the school. His father, Samuel Baird, was the first engineer for the city of Ballarat. According to his grandson Samuel Baird was indentured to a local chemist in Ballarat. He moved to Melbourne and took over the chemist business Hood and Co in Elizabeth Street Melbourne. This business remained in the family for a further generation. This certificate is accompanied by an earlier certificate indicating that Samuel also sat a matriculation examination in October 1871 and passed in four subjects (000132.1). The certificates are accompanied by signed receipts from the University of Melbourne for matriculation examinations at a totla of four times - Receipt no 503 30 October 1871 for 5 subjects (000132.2) Receipt no 495 6 August 1872 less than six subjects (000132.3) Receipt no 696 29 October 1872 for 8 subjects (000132.4) Receipt no 195 14 February 1873 for matriculation exam (000132.5) for purchased copies of matriculation certificates. This infers that Samuel Baird sat some portion of the matriculation certificate over four examinations. Record 000131 is related to these items being a reference from the Principal Robert Oliver McCoy for Samuel Baird written in 1873. Historic significance for its connection with the first student of Ballarat College. Single sheet form printed on one side with handwritten insertions. Front: THE UNIVERSITY OF MELBOURNE / MATRICULATION EXAMINATION CERTIFICATE / At a Matriculation Examination held in the / October Term, 1872 / Samuel Baird / passed in the following six subjects: / 1. Latin 4. Arithmetic / 2. English 5. Algebra / 3. French 6. Euclid / [Signature] President / 14 Feb 1873 [Signature] Registrarsamuel-baird, 1864, ballarat-college, receipt, university-of-melbourne, matriculation

Louise Amy Breaks, also known as Lulu, died on the 8 May 1943. An error on the plaque mentions 1945 which was likeky erected later. In her obituary published on the Williamstown Chronicle, Friday 14 May 1943, page 1: A well-known and very highly respected resident of this city, Miss Louise Amy (Lulu) Breaks, of 4 Jackson Court, Ferguson St., died on Saturday morning, after a brief Illness. Deceased was born .ocally and was the eldest daughter of the late Engineer Commander James L. Breaks, R.N., and Alice Breaks. Deceased was a very prominent member and worker of Holy Trinity Church and actively identified with every caritable movement in this City. She leaves a sister, Miss Maude Breaks, to mourn her loss. The funeral took place on Monday afternioon, leaving Holy Trinity Church after a service conducted by the Rev. J. H. Raverty, assisted by the Revs. S. P. H. Martin and Oliver. The large congregation in the Church, lengthy cortege, and very large number of floral tributes received testified to the esteem in which deceased was held. Ernest W. Jackson. had charge of the funeral arrangements, and the Rev. J. H: Raverty officiated at the cemetery.Louise Breaks and her family were active members of the Mission. Her father James Lennox Breaks, aged 22 years, sailed from England on the Cerberus on her maiden voyage, and was associated with the ship for 34 years until he retired. Commemorative Plaque for Louise Amy Breakswilliamstown, seamen's institute, seamen's mission, mission to seamen, nelson place, st nicholas chapel, james l. breaks, engineering commander, alice breaks, maude breaks, alice breaks nee jobson, hms cerberus, lhlg, lightkeepers' auxiliary

Since 1895, Hobbies Ltd have been supplying model makers and enthusiasts throughout the world with a wide range of quality model kits, accessories, tools, components and handbooks. The Hobbies Company began life in Dereham, Norfolk in 1881 with a London Office opened later (1922) at 65 New Oxford Street, WC1. In 1895 Hobbies began supplying model makers with their products and in 1897 were incorporated into a Public company. In 1922 at a British Industries Fair the company had a stand advertising their products as "The All-British Firm with a World reputation". Fretwork Outfits. Fretwork Machines. Carpentry Outfits. Strip work Outfits. Also manufactures of Fretwork Tools and Benches, Wood, Circular Saws, Lathes, Picture Framing Outfits, Tools, etc. In 1947 the company had expanded and was still making tools and materials for the amateur craftsman in wood. They had acquired a reputation as manufacturers of quality Fretwork Outfits, Tools, Treadle Machines, Model Maker's Tool Kits. The company also publishers of ‘Hobbies Weekly magazine’ and also sold plans for fretwork, model making and wooden toys. In 1961 they were still manufacturers and retailers of craft tools and materials, timber merchants, light engineers and Government contractors with around 500 employees. A vintage tool made for hobbyists and distributed throughout the world by a British company that is still in existence today. The item is significant as it catalogues the manufactures history at a specific time in the company's development.Foot operated treadle Fret saw called "GEM" subject item is a short saw , the stand in the background is the base for a Delta Q3 model scroll saw. Gem inscription cast into the cast iron frameworkflagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, saw, treadle saw, fret saw, pedal saw, the gem, tool, hobbies ltd, treadle, foot operated

Originally contained in a 'magnetic' photo album of scenic photos of Yan Yean and Warrandyte believed to be donated by Mrs Eric Stephenson, Jingalong, 110 Ryans Road, Eltham, Vic. 3095; relocated to archival safe storage. On the 20th December 1853 Lieut Governor Charles LaTrobe took his spade to turn the first sod of an embankment across the swampy bed of the Plenty River at a lonely place called Yan Yean, in order to create Melbourne’s first water supply. In the early 1850’s water had been drawn from the Yarra which even then was known as Yarra Soup. A convict by the name of James Blackburn produced the basic design for supplying water to Melbourne from a reservoir on the Plenty River at Yan Yean, and later on he was appointed consulting engineer on the project. In 1853 a contract was let for the building of the wall for 91 thousand 575 pounds, and at one stage some 400 labourers were at work in the area. A tramway was constructed to convey stone and other materials from Melbourne. So famous was this magnificent stretch of water that illustrations of the bluestone embankment and tower appeared in London journals Whittlesea Historical Society – Historic items for Diamond Valley Community Radio September 1990 Colour photographyan yean, yan yean reservoir

Originally contained in a 'magnetic' photo album of scenic photos of Yan Yean and Warrandyte believed to be donated by Mrs Eric Stephenson, Jingalong, 110 Ryans Road, Eltham, Vic. 3095; relocated to archival safe storage. On the 20th December 1853 Lieut Governor Charles LaTrobe took his spade to turn the first sod of an embankment across the swampy bed of the Plenty River at a lonely place called Yan Yean, in order to create Melbourne’s first water supply. In the early 1850’s water had been drawn from the Yarra which even then was known as Yarra Soup. A convict by the name of James Blackburn produced the basic design for supplying water to Melbourne from a reservoir on the Plenty River at Yan Yean, and later on he was appointed consulting engineer on the project. In 1853 a contract was let for the building of the wall for 91 thousand 575 pounds, and at one stage some 400 labourers were at work in the area. A tramway was constructed to convey stone and other materials from Melbourne. So famous was this magnificent stretch of water that illustrations of the bluestone embankment and tower appeared in London journals Whittlesea Historical Society – Historic items for Diamond Valley Community Radio September 1990 Colour photographyan yean, yan yean reservoir

Originally contained in a 'magnetic' photo album of scenic photos of Yan Yean and Warrandyte believed to be donated by Mrs Eric Stephenson, Jingalong, 110 Ryans Road, Eltham, Vic. 3095; relocated to archival safe storage. On the 20th December 1853 Lieut Governor Charles LaTrobe took his spade to turn the first sod of an embankment across the swampy bed of the Plenty River at a lonely place called Yan Yean, in order to create Melbourne’s first water supply. In the early 1850’s water had been drawn from the Yarra which even then was known as Yarra Soup. A convict by the name of James Blackburn produced the basic design for supplying water to Melbourne from a reservoir on the Plenty River at Yan Yean, and later on he was appointed consulting engineer on the project. In 1853 a contract was let for the building of the wall for 91 thousand 575 pounds, and at one stage some 400 labourers were at work in the area. A tramway was constructed to convey stone and other materials from Melbourne. So famous was this magnificent stretch of water that illustrations of the bluestone embankment and tower appeared in London journals Whittlesea Historical Society – Historic items for Diamond Valley Community Radio September 1990 Colour photographyan yean, yan yean reservoir

Originally contained in a 'magnetic' photo album of scenic photos of Yan Yean and Warrandyte believed to be donated by Mrs Eric Stephenson, Jingalong, 110 Ryans Road, Eltham, Vic. 3095; relocated to archival safe storage. On the 20th December 1853 Lieut Governor Charles LaTrobe took his spade to turn the first sod of an embankment across the swampy bed of the Plenty River at a lonely place called Yan Yean, in order to create Melbourne’s first water supply. In the early 1850’s water had been drawn from the Yarra which even then was known as Yarra Soup. A convict by the name of James Blackburn produced the basic design for supplying water to Melbourne from a reservoir on the Plenty River at Yan Yean, and later on he was appointed consulting engineer on the project. In 1853 a contract was let for the building of the wall for 91 thousand 575 pounds, and at one stage some 400 labourers were at work in the area. A tramway was constructed to convey stone and other materials from Melbourne. So famous was this magnificent stretch of water that illustrations of the bluestone embankment and tower appeared in London journals Whittlesea Historical Society – Historic items for Diamond Valley Community Radio September 1990 Colour photographyan yean, yan yean reservoir

Originally contained in a 'magnetic' photo album of scenic photos of Yan Yean and Warrandyte believed to be donated by Mrs Eric Stephenson, Jingalong, 110 Ryans Road, Eltham, Vic. 3095; relocated to archival safe storage. On the 20th December 1853 Lieut Governor Charles LaTrobe took his spade to turn the first sod of an embankment across the swampy bed of the Plenty River at a lonely place called Yan Yean, in order to create Melbourne’s first water supply. In the early 1850’s water had been drawn from the Yarra which even then was known as Yarra Soup. A convict by the name of James Blackburn produced the basic design for supplying water to Melbourne from a reservoir on the Plenty River at Yan Yean, and later on he was appointed consulting engineer on the project. In 1853 a contract was let for the building of the wall for 91 thousand 575 pounds, and at one stage some 400 labourers were at work in the area. A tramway was constructed to convey stone and other materials from Melbourne. So famous was this magnificent stretch of water that illustrations of the bluestone embankment and tower appeared in London journals Whittlesea Historical Society – Historic items for Diamond Valley Community Radio September 1990Colour photographyan yean, yan yean reservoir